INA125U/2K5 - Low-Power Precision Instrumentation Amplifier with 2.5V Reference
MPN: INA125U/2K5 ✓ AktifINA125U/2K5 Ringkasan
An instrumentation amplifier is a differential-input amplifier optimized for measuring small signals buried in noise and common-mode interference. The category hierarchy runs instrumentation amplifier -> differential amplifier -> amplifier IC -> integrated circuit -> semiconductor. Unlike a discrete op-amp difference stage, an INA offers high input impedance, matched resistors, excellent common-mode rejection and a single-gain-set resistor, which is why it dominates strain-gauge, bridge and ratiometric sensor front ends.
Key features include a 50 uV maximum input offset voltage, a 2 uV/°C input offset voltage temperature coefficient, a 460 uA typical supply current for low-power designs, a 2 V/µs slew rate, and 60 µs settling time. The internal reference supplies a stable excitation voltage for bridge circuits, and an enable/shutdown pin supports power management. Overvoltage protection guards inputs during industrial transients.
Technically, the device uses a three-op-amp topology with laser-trimmed internal feedback resistors, so gain accuracy depends only on the external gain resistor. The on-board precision reference makes ratiometric conversion with an ADC possible without a second supply, and the reference can also serve as an external excitation source. The single external gain resistor keeps the calibration chain short, which supports the 0.075% gain error class of the device.
Typical applications include strain-gauge and load-cell front ends, isolated transmitter analog sections, bridge-powered sensor modules, medical monitoring instrumentation, and 4-20 mA loop signal conditioning where the reference eliminates a separate excitation supply.
When designing around the INA125U/2K5, keep the gain resistor close to the RG pin and use the recommended supply bypassing. Because it is a linear amplifier with a wide supply range, excessive headroom at high gain costs power and heat; choose the smallest gain that meets the sensitivity target.
This page consolidates distributor availability, drop-in same-family alternatives, parameter-by-parameter comparison, and practical layout notes that are not collected in a single place in the manufacturer datasheet.
Alternatif penggantian untuk INA125U/2K5 — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian INA125U/2K5 (sama faktor bentuk dan footprint) — berbeda di dalam Package, Gain Range, Common-Mode Rejection Ratio, Number of Channels, Quiescent Current.
INA125UA/2K5
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
INA125UA
✅ Drop-InKontak untuk harga
Lihat Datasheet →INA125U
✅ Drop-InKontak untuk harga
Lihat Datasheet →INA125U/2K5 Rating Maksimal & Karakteristik Listrik
| Device Type | Instrumentation amplifier with precision voltage reference |
| Supply Voltage Range | 2.7 V to 36 V |
| Maximum Total Supply Voltage | -18 V to +18 V (±18 V) |
| Gain Range | 4 V/V to 10,000 V/V, set by one external resistor |
| Gain Error (max) | 0.075% |
| Input Offset Voltage (max) | 50 uV |
| Input Offset Voltage Temperature Coefficient | 2 uV/°C |
| Input Bias Current | 10 nA |
| Common-Mode Rejection Ratio | 100 dB |
| Input Voltage Noise Density | 38 nV/√Hz at 1 kHz |
| Gain-Bandwidth Product | 0.15 MHz |
| Slew Rate | 2 V/µs |
| Settling Time | 60 µs |
| Typical Supply Current | 460 uA |
| Internal Reference Output | 2.5 V precision voltage reference |
| Rentang Suhu Kerja | -40 °C to +85 °C |
| Paket | 16-pin SOIC, PDSO16 |
| Tipe Mounting | Surface mount |
| Enable / Shutdown Control | Yes, enable/shutdown pin |
| Input Overvoltage Protection | Yes |
| Status RoHS | Compliant |
INA125U/2K5 16-pin soic, pdso16 Diamant Konfigurasi Panduan
Konfigurasi pin untuk INA125U/2K5 (16-pin soic, pdso16 pakai pakai). Komponen analog ini memiliki pin masukan, keluaran, dan pengirim daya. Lihat datasheet produsen untuk konfigurasi pin offset null, kompensasi, dan pengaktifan. Ideal untuk peralatan sinyal dan kabel penggandaran.
Tidak ada data diatribut pin yang tersedia untuk INA125U/2K5.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
INA125U/2K5 cocok untuk 6 aplikasis: Strain-Gauge and Load-Cell Front End, Ratiometric ADC Signal Conditioning, Industrial Transmitter Signal Conditioning, Medical and Biosignal Monitoring, Precision Bridge Excitation for Test and Measurement, Low-Power Sensor Node and IoT Edge.
Strain-Gauge and Load-Cell Front End
The INA125U/2K5 suits strain-gauge and load-cell bridges because it combines a 2.5 V precision reference output with a differential gain stage of 4 V/V to 10,000 V/V set by one resistor. With 100 dB CMRR, 38 nV/√Hz input noise at 1 kHz and 50 uV maximum input offset, the amplified millivolt-level bridge output can be sampled directly by a SAR ADC. Placing the gain resistor close to the RG pin and keeping the bridge wiring away from switching nodes preserves the ratiometric cancellation that makes the reference valuable. The 460 uA supply current keeps battery and portable load-cell modules compact without heatsinking.
Direkomendasikan
Ratiometric ADC Signal Conditioning
In ratiometric conversion the ADC reference and the sensor excitation share the same source, so supply drift cancels in the digital result. The INA125U/2K5 supports this directly: its on-board 2.5 V precision reference can drive both the bridge and the ADC reference input, eliminating a separate excitation supply. Gain accuracy of 0.075% then comes almost entirely from the external gain resistor, so a 0.05% resistor is usually sufficient. This makes the device a good fit for weighing, pressure and level systems where absolute calibration stability matters more than wide bandwidth.
Direkomendasikan
Industrial Transmitter Signal Conditioning
Field transmitters often need to survive industrial transients while delivering accurate measurement to a remote 4-20 mA loop. The INA125U/2K5 provides the differential accuracy, high input impedance and 100 dB CMRR needed to reject ground-potential differences between sensor and transmitter ground. Its input overvoltage protection helps in installations where cabling is long, and the enable/shutdown pin allows the analog section to be powered down during maintenance windows. Operating from 2.7 V to 36 V permits single 5 V or 24 V loop-powered rails.
Direkomendasikan
Medical and Biosignal Monitoring
Low-noise differential acquisition is central to patient monitoring, where small bioelectric signals sit on large electrode offsets. The INA125U/2K5 offers 38 nV/√Hz input noise at 1 kHz, a 2 uV/°C offset drift coefficient and 100 dB CMRR in a 16-pin SOIC package, enough to build compact single-channel front ends without a separate instrumentation amplifier stage. The integrated 2.5 V reference supports self-calibrated excitation for resistive sensors, while the 0.15 MHz bandwidth suits ECG-style and pressure-style signals rather than high-speed imaging chains.
Direkomendasikan
Precision Bridge Excitation for Test and Measurement
Instrumentation setups often need a quiet, well-defined excitation source plus a differential receiver in one device. The INA125U/2K5 provides both, so a bench module can supply bridge excitation from the internal 2.5 V reference and measure the resulting differential output with 4 V/V to 10,000 V/V gain. The 60 µs settling time and 2 V/µs slew rate suit slow precision measurements and pulsed test sequences, while the -40 °C to +85 °C range supports laboratory and industrial chassis environments. The wide 2.7 V to 36 V supply span allows use from battery-powered fixtures to 24 V racks.
Direkomendasikan
Low-Power Sensor Node and IoT Edge
Battery-powered sensor nodes must hold quiescent current low without giving up differential accuracy, and the INA125U/2K5 draws about 460 uA typical supply current while keeping offset at 50 uV maximum. In a self-powered bridge node, the internal 2.5 V reference excites the sensor and the amplifier conditions the output for a low-power ADC, and the enable/shutdown pin lets the analog section sleep between samples. The 16-pin SOIC package keeps board area small for compact IoT enclosures, and 2.7 V minimum supply supports coin-cell and energy-harvesting rails.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk INA125U/2K5 — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | INA125UA/2K5 | INA125UA | INA125U |
|---|---|---|---|---|
| Package | 16-pin SOIC (PDSO16) | 16-pin SOIC (PDSO16) - same | 16-pin SOIC (PDSO16) - same | 16-pin SOIC (PDSO16) - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Device Type | Instrumentation amplifier with precision voltage reference | Instrumentation amplifier with precision voltage reference | Instrumentation amplifier with precision voltage reference | Instrumentation amplifier with precision voltage reference |
| Supply Voltage Range | 2.7 V to 36 V | 2.7 V to 36 V | 2.7 V to 36 V | 2.7 V to 36 V |
| Gain Range | 4 V/V to 10,000 V/V (external resistor) | 4 V/V to 10,000 V/V (external resistor) | 4 V/V to 10,000 V/V (external resistor) | 4 V/V to 10,000 V/V (external resistor) |
| Accuracy Grade | Standard grade (gain error 0.075% max) | Higher-precision UA grade, tighter offset and gain limits | Higher-precision UA grade, tighter offset and gain limits | Standard grade |
| Common-Mode Rejection Ratio | 100 dB | 100 dB | 100 dB | 100 dB |
| Input Noise Density | 38 nV/√Hz at 1 kHz | 38 nV/√Hz at 1 kHz | 38 nV/√Hz at 1 kHz | 38 nV/√Hz at 1 kHz |
| Bandwidth | 0.15 MHz | 0.15 MHz | 0.15 MHz | 0.15 MHz |
| Supply Current (typical) | 460 uA | 460 uA | 460 uA | 460 uA |
| Internal Reference Output | 2.5 V precision voltage reference | 2.5 V precision voltage reference | 2.5 V precision voltage reference | 2.5 V precision voltage reference |
Diferensiator Kunci
- Integrated precision 2.5 V reference with the amplifier on one die (vsINA125UA)
- Single-resistor gain setting across a 4 to 10,000 V/V range (vsINA125U)
- Higher-precision grade available without any footprint or pin change (vsINA125UA/2K5)
Catatan Desain
Place the external gain resistor directly at the RG pin with a short, low-inductance trace, because stray capacitance in combination with the internal gain network degrades bandwidth and can cause peaking around the 0.15 MHz corner. Route the two differential inputs as a matched pair on a quiet layer, keep them away from the reference output and supply traces, and connect the reference output only to the bridge or ADC reference input. Use the manufacturer recommended bypass capacitor close to the supply pins.
A frequent field issue is assuming the gain is set by two resistors or by a digital control, when the INA125U/2K5 uses a single external resistor and the UA and U grades differ only in accuracy limits. Another trap is leaving the enable/shutdown pin floating, which can leave the amplifier in an indeterminate state; tie it to the supply or drive it from the host. Finally, the 2.5 V reference output cannot source large currents, so do not use it to power unrelated circuitry.
For bridge work, keep sensor wiring short and shield it, and ground the shield at the amplifier end only to avoid a ground loop that degrades the 100 dB CMRR figure. If the source impedance is high, add matched input bias compensation resistors as described in the manufacturer datasheet to preserve common-mode rejection balance. Because the offset drift is 2 uV/°C, specify resistors with low temperature coefficient for the gain network when working across wide ambient ranges.
Estimated: with a 5 V supply and 460 uA typical supply current, device dissipation is about 2.3 mW, so no thermal derating is required at low supply voltages. At a 24 V supply the same current gives roughly 11 mW, still negligible. The real thermal constraint is the linear output stage driving a low-impedance load at high gain, so budget output current separately from the 460 uA quiescent figure and keep the load impedance high enough that the output does not saturate.
Informasi Konformitas
RoHS compliance is listed for the INA125U/2K5 on the Texas Instruments product page. The part is an industrial/commercial grade device rated -40 °C to +85 °C, with no AEC-Q100 automotive-qualified option in this orderable line.