INA125U/2K5 - Low-Power Precision Instrumentation Amplifier with 2.5V Reference
MPN: INA125U/2K5 ✓ 啟用中INA125U/2K5 概覽
An instrumentation amplifier is a differential-input amplifier optimized for measuring small signals buried in noise and common-mode interference. The category hierarchy runs instrumentation amplifier -> differential amplifier -> amplifier IC -> integrated circuit -> semiconductor. Unlike a discrete op-amp difference stage, an INA offers high input impedance, matched resistors, excellent common-mode rejection and a single-gain-set resistor, which is why it dominates strain-gauge, bridge and ratiometric sensor front ends.
Key features include a 50 uV maximum input offset voltage, a 2 uV/°C input offset voltage temperature coefficient, a 460 uA typical supply current for low-power designs, a 2 V/µs slew rate, and 60 µs settling time. The internal reference supplies a stable excitation voltage for bridge circuits, and an enable/shutdown pin supports power management. Overvoltage protection guards inputs during industrial transients.
Technically, the device uses a three-op-amp topology with laser-trimmed internal feedback resistors, so gain accuracy depends only on the external gain resistor. The on-board precision reference makes ratiometric conversion with an ADC possible without a second supply, and the reference can also serve as an external excitation source. The single external gain resistor keeps the calibration chain short, which supports the 0.075% gain error class of the device.
Typical applications include strain-gauge and load-cell front ends, isolated transmitter analog sections, bridge-powered sensor modules, medical monitoring instrumentation, and 4-20 mA loop signal conditioning where the reference eliminates a separate excitation supply.
When designing around the INA125U/2K5, keep the gain resistor close to the RG pin and use the recommended supply bypassing. Because it is a linear amplifier with a wide supply range, excessive headroom at high gain costs power and heat; choose the smallest gain that meets the sensitivity target.
This page consolidates distributor availability, drop-in same-family alternatives, parameter-by-parameter comparison, and practical layout notes that are not collected in a single place in the manufacturer datasheet.
直接替換替代品,適用於 INA125U/2K5 — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: INA125U/2K5 (相同外形與佔位) — 差異在於 Package, Gain Range, Common-Mode Rejection Ratio, Number of Channels, Quiescent Current.
INA125UA/2K5
✅ 直接替換📋 參考替代品(不在目錄中)
INA125U/2K5 最大額定值與電氣特性
| Device Type | Instrumentation amplifier with precision voltage reference |
| Supply Voltage Range | 2.7 V to 36 V |
| Maximum Total Supply Voltage | -18 V to +18 V (±18 V) |
| Gain Range | 4 V/V to 10,000 V/V, set by one external resistor |
| Gain Error (max) | 0.075% |
| Input Offset Voltage (max) | 50 uV |
| Input Offset Voltage Temperature Coefficient | 2 uV/°C |
| Input Bias Current | 10 nA |
| Common-Mode Rejection Ratio | 100 dB |
| Input Voltage Noise Density | 38 nV/√Hz at 1 kHz |
| Gain-Bandwidth Product | 0.15 MHz |
| Slew Rate | 2 V/µs |
| Settling Time | 60 µs |
| Typical Supply Current | 460 uA |
| Internal Reference Output | 2.5 V precision voltage reference |
| 工作溫度範圍 | -40 °C to +85 °C |
| 封裝 | 16-pin SOIC, PDSO16 |
| 安裝類型 | Surface mount |
| Enable / Shutdown Control | Yes, enable/shutdown pin |
| Input Overvoltage Protection | Yes |
| RoHS 狀態 | Compliant |
INA125U/2K5 16-pin soic, pdso16 腳位配置指南
INA125U/2K5(16-pin soic, pdso16 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: INA125U/2K5.
請參閱 資料表 以查看完整腳位配置。
典型應用
INA125U/2K5 適用於 6 應用s: Strain-Gauge and Load-Cell Front End, Ratiometric ADC Signal Conditioning, Industrial Transmitter Signal Conditioning, Medical and Biosignal Monitoring, Precision Bridge Excitation for Test and Measurement, Low-Power Sensor Node and IoT Edge.
Strain-Gauge and Load-Cell Front End
The INA125U/2K5 suits strain-gauge and load-cell bridges because it combines a 2.5 V precision reference output with a differential gain stage of 4 V/V to 10,000 V/V set by one resistor. With 100 dB CMRR, 38 nV/√Hz input noise at 1 kHz and 50 uV maximum input offset, the amplified millivolt-level bridge output can be sampled directly by a SAR ADC. Placing the gain resistor close to the RG pin and keeping the bridge wiring away from switching nodes preserves the ratiometric cancellation that makes the reference valuable. The 460 uA supply current keeps battery and portable load-cell modules compact without heatsinking.
推薦
Ratiometric ADC Signal Conditioning
In ratiometric conversion the ADC reference and the sensor excitation share the same source, so supply drift cancels in the digital result. The INA125U/2K5 supports this directly: its on-board 2.5 V precision reference can drive both the bridge and the ADC reference input, eliminating a separate excitation supply. Gain accuracy of 0.075% then comes almost entirely from the external gain resistor, so a 0.05% resistor is usually sufficient. This makes the device a good fit for weighing, pressure and level systems where absolute calibration stability matters more than wide bandwidth.
推薦
Industrial Transmitter Signal Conditioning
Field transmitters often need to survive industrial transients while delivering accurate measurement to a remote 4-20 mA loop. The INA125U/2K5 provides the differential accuracy, high input impedance and 100 dB CMRR needed to reject ground-potential differences between sensor and transmitter ground. Its input overvoltage protection helps in installations where cabling is long, and the enable/shutdown pin allows the analog section to be powered down during maintenance windows. Operating from 2.7 V to 36 V permits single 5 V or 24 V loop-powered rails.
推薦
Medical and Biosignal Monitoring
Low-noise differential acquisition is central to patient monitoring, where small bioelectric signals sit on large electrode offsets. The INA125U/2K5 offers 38 nV/√Hz input noise at 1 kHz, a 2 uV/°C offset drift coefficient and 100 dB CMRR in a 16-pin SOIC package, enough to build compact single-channel front ends without a separate instrumentation amplifier stage. The integrated 2.5 V reference supports self-calibrated excitation for resistive sensors, while the 0.15 MHz bandwidth suits ECG-style and pressure-style signals rather than high-speed imaging chains.
推薦
Precision Bridge Excitation for Test and Measurement
Instrumentation setups often need a quiet, well-defined excitation source plus a differential receiver in one device. The INA125U/2K5 provides both, so a bench module can supply bridge excitation from the internal 2.5 V reference and measure the resulting differential output with 4 V/V to 10,000 V/V gain. The 60 µs settling time and 2 V/µs slew rate suit slow precision measurements and pulsed test sequences, while the -40 °C to +85 °C range supports laboratory and industrial chassis environments. The wide 2.7 V to 36 V supply span allows use from battery-powered fixtures to 24 V racks.
推薦
Low-Power Sensor Node and IoT Edge
Battery-powered sensor nodes must hold quiescent current low without giving up differential accuracy, and the INA125U/2K5 draws about 460 uA typical supply current while keeping offset at 50 uV maximum. In a self-powered bridge node, the internal 2.5 V reference excites the sensor and the amplifier conditions the output for a low-power ADC, and the enable/shutdown pin lets the analog section sleep between samples. The 16-pin SOIC package keeps board area small for compact IoT enclosures, and 2.7 V minimum supply supports coin-cell and energy-harvesting rails.
推薦
推薦產品摘要
工程參考資料,適用於 INA125U/2K5 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | INA125UA/2K5 | INA125UA | INA125U |
|---|---|---|---|---|
| Package | 16-pin SOIC (PDSO16) | 16-pin SOIC (PDSO16) - same | 16-pin SOIC (PDSO16) - same | 16-pin SOIC (PDSO16) - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Device Type | Instrumentation amplifier with precision voltage reference | Instrumentation amplifier with precision voltage reference | Instrumentation amplifier with precision voltage reference | Instrumentation amplifier with precision voltage reference |
| Supply Voltage Range | 2.7 V to 36 V | 2.7 V to 36 V | 2.7 V to 36 V | 2.7 V to 36 V |
| Gain Range | 4 V/V to 10,000 V/V (external resistor) | 4 V/V to 10,000 V/V (external resistor) | 4 V/V to 10,000 V/V (external resistor) | 4 V/V to 10,000 V/V (external resistor) |
| Accuracy Grade | Standard grade (gain error 0.075% max) | Higher-precision UA grade, tighter offset and gain limits | Higher-precision UA grade, tighter offset and gain limits | Standard grade |
| Common-Mode Rejection Ratio | 100 dB | 100 dB | 100 dB | 100 dB |
| Input Noise Density | 38 nV/√Hz at 1 kHz | 38 nV/√Hz at 1 kHz | 38 nV/√Hz at 1 kHz | 38 nV/√Hz at 1 kHz |
| Bandwidth | 0.15 MHz | 0.15 MHz | 0.15 MHz | 0.15 MHz |
| Supply Current (typical) | 460 uA | 460 uA | 460 uA | 460 uA |
| Internal Reference Output | 2.5 V precision voltage reference | 2.5 V precision voltage reference | 2.5 V precision voltage reference | 2.5 V precision voltage reference |
主要差異化特點
- Integrated precision 2.5 V reference with the amplifier on one die (對比INA125UA)
- Single-resistor gain setting across a 4 to 10,000 V/V range (對比INA125U)
- Higher-precision grade available without any footprint or pin change (對比INA125UA/2K5)
設計說明
Place the external gain resistor directly at the RG pin with a short, low-inductance trace, because stray capacitance in combination with the internal gain network degrades bandwidth and can cause peaking around the 0.15 MHz corner. Route the two differential inputs as a matched pair on a quiet layer, keep them away from the reference output and supply traces, and connect the reference output only to the bridge or ADC reference input. Use the manufacturer recommended bypass capacitor close to the supply pins.
A frequent field issue is assuming the gain is set by two resistors or by a digital control, when the INA125U/2K5 uses a single external resistor and the UA and U grades differ only in accuracy limits. Another trap is leaving the enable/shutdown pin floating, which can leave the amplifier in an indeterminate state; tie it to the supply or drive it from the host. Finally, the 2.5 V reference output cannot source large currents, so do not use it to power unrelated circuitry.
For bridge work, keep sensor wiring short and shield it, and ground the shield at the amplifier end only to avoid a ground loop that degrades the 100 dB CMRR figure. If the source impedance is high, add matched input bias compensation resistors as described in the manufacturer datasheet to preserve common-mode rejection balance. Because the offset drift is 2 uV/°C, specify resistors with low temperature coefficient for the gain network when working across wide ambient ranges.
Estimated: with a 5 V supply and 460 uA typical supply current, device dissipation is about 2.3 mW, so no thermal derating is required at low supply voltages. At a 24 V supply the same current gives roughly 11 mW, still negligible. The real thermal constraint is the linear output stage driving a low-impedance load at high gain, so budget output current separately from the 460 uA quiescent figure and keep the load impedance high enough that the output does not saturate.
合規資訊
RoHS compliance is listed for the INA125U/2K5 on the Texas Instruments product page. The part is an industrial/commercial grade device rated -40 °C to +85 °C, with no AEC-Q100 automotive-qualified option in this orderable line.