ISL8485IB-T - 5V 5Mbps RS-485/RS-422 Transceiver | Renesas
MPN: ISL8485IB-T ✓ AktifISL8485IB-T Ringkasan
An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals to and from differential balanced pairs. The RS-485 standard supports multipoint buses and longer interconnects with excellent noise immunity, while RS-422 provides a point-to-point differential interface. The ISL8485 family is specified as a BiCMOS single-transceiver solution that can satisfy both interface types, making it useful where field buses, industrial controllers, and instrumentation share a common physical layer.
The ISL8485IB-T operates from 4.5 V to 5.5 V and supports data rates up to 5 Mbps. It presents one unit load to an RS-485 bus, allowing up to 32 transceivers on the network when system loading and cabling conditions permit. Its half-duplex architecture reduces the number of external interface signals, while the 8-pin SOIC package supports compact surface-mount implementations.
The BiCMOS architecture combines bipolar and CMOS characteristics to support the drive and receive functions required by balanced communication links. The device family includes high-speed and slew-rate-limited operating choices, so the appropriate variant should be selected according to edge-rate requirements, cable length, topology, and electromagnetic-emissions constraints. The IB designation identifies the slew-rate-limited family option rather than the fastest A-series option.
Typical uses include industrial RS-485 field-bus links, building-control networks, factory equipment interfaces, data-acquisition systems, instrumentation, and communications equipment requiring a compact 5 V differential transceiver. Selection should account for bus direction control, termination, biasing, grounding, and the number of nodes connected to the same cable segment.
For a new PCB, place the transceiver and its decoupling capacitor close to the supply pins, connect the differential pair as a controlled-impedance route, and keep the driver, receiver, and connector ground references in one continuous plane. Add termination only where required by the network topology and verify common-mode voltage, stub length, and radiated emissions in the final equipment.
This product page combines the ISL8485 family electrical characteristics with package guidance, application analysis, and a parameter-focused comparison of compatible Renesas transceiver options. It is intended to help engineers narrow the choice before completing board-level timing, emissions, and fault-tolerance validation.
Alternatif penggantian untuk ISL8485IB-T — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian ISL8485IB-T (sama faktor bentuk dan footprint) — berbeda di dalam Transceiver Configuration.
ISL8485IBZ-T
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
ISL8485ABZ-T
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
ISL8485CBZ-T
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
ISL8490IBZ-T
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
ISL8491IBZ-T
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
ISL8485IB-T Spesifikasi
| Product Type | Single RS-485/RS-422 transceiver |
| Transceiver Configuration | 1 driver and 1 receiver |
| Duplex Mode | Half-duplex |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Nominal Supply Voltage | 5 V |
| Maximum Data Rate | 5 Mbps |
| Interface Standards | RS-485 and RS-422 |
| Logic Technology | BiCMOS |
| RS-485 Bus Load | 1 unit load |
| Maximum RS-485 Transceiver Count | 32 transceivers |
| Paket | 8-pin SOIC |
| Package Width | 3.90 mm |
| Tipe Mounting | Surface mount |
| RoHS Compliance | unknown |
| REACH Compliance | unknown |
| AEC-Q100 Qualification | unknown |
ISL8485IB-T 3.90 mm Diamant Konfigurasi Panduan
Konfigurasi pin untuk ISL8485IB-T (3.90 mm pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.
Tidak ada data diatribut pin yang tersedia untuk ISL8485IB-T.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
ISL8485IB-T cocok untuk 6 aplikasis: Industrial RS-485 Field Bus, Building Automation Controller, Data Acquisition Equipment, Factory Equipment Interface, Instrumentation and Test Equipment, Point-to-Point RS-422 Link.
Industrial RS-485 Field Bus
The ISL8485IB-T suits industrial field-bus nodes that require a 5 V differential interface and up to 5 Mbps capability. Its one-unit-load RS-485 presentation allows as many as 32 transceivers on a network when the physical topology permits. The slew-rate-limited B-series choice can reduce unwanted fast-edge activity on industrial wiring, although the final cable length, topology, and emissions requirements must determine whether it is preferable to the high-speed A-series option.
Direkomendasikan
Building Automation Controller
The ISL8485IB-T can connect a building-control controller to balanced RS-485 networks carrying sensor, actuator, and supervisory data. Its 4.5 V to 5.5 V operating range matches regulated 5 V controller rails, while the half-duplex arrangement reduces interface logic compared with a full-duplex design. Designers should use a continuous ground reference, suitable bus biasing, and termination appropriate to the cable topology to preserve signal integrity over the installed distance.
Direkomendasikan
Data Acquisition Equipment
The ISL8485IB-T is appropriate for data-acquisition equipment that exchanges measurements over an RS-485 or RS-422 balanced link. The one-driver, one-receiver arrangement supports half-duplex communication while the family data-rate ceiling of 5 Mbps provides ample margin for many digitized sensor streams. The receiver must be enabled only when the bus is not being driven, and cable routing should minimize stub lengths and maintain a common ground reference for reliable operation.
Direkomendasikan
Factory Equipment Interface
The ISL8485IB-T provides a compact physical layer for factory equipment controllers, motor-support modules, and remote I/O nodes. Its 8-pin SOIC package preserves board area, while the 4.5 V to 5.5 V supply range accommodates conventional 5 V logic. In equipment cabinets with long cables or adjacent switching power converters, the slew-rate-limited selection should be checked against emissions limits, termination strategy, and the timing requirements of the master controller.
Direkomendasikan
Instrumentation and Test Equipment
The ISL8485IB-T is useful in instrumentation that communicates through a robust differential port while retaining a compact 5 V implementation. Its one-unit-load RS-485 behavior allows several instruments or nodes to share a bus, subject to the documented 32-transceiver maximum and physical-layer design. The slew-rate-limited option can be advantageous on external cables where controlled transition rates help limit high-frequency content, but interoperability and receiver timing must be verified with every connected device.
Direkomendasikan
Point-to-Point RS-422 Link
The ISL8485IB-T can implement an RS-422 point-to-point link when a system prefers the same physical transceiver family used for RS-485 nodes. The 5 V supply and one-unit-load interface simplify integration with 5 V controllers, and the family's 5 Mbps rating supports moderately high-speed command or monitoring traffic. Because the device is also used in half-duplex RS-485 networks, the application must provide correct driver-enable and receiver-enable control while also observing the RS-422 termination arrangement.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk ISL8485IB-T — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | ISL8485IBZ-T | ISL8485ABZ-T | ISL8485CBZ-T | ISL8490IBZ-T |
|---|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Product Type | RS-485/RS-422 transceiver | RS-485/RS-422 transceiver | RS-485/RS-422 transceiver | RS-485/RS-422 transceiver | RS-485/RS-422 transceiver |
| Nominal Supply Voltage | 5 V | 5 V | 5 V | 5 V | 5 V |
| Supply Voltage Range | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V |
| Maximum Data Rate | 5 Mbps | 5 Mbps | 5 Mbps | 5 Mbps | 5 Mbps |
| Duplex Mode | Half-duplex | Half-duplex | Half-duplex | Half-duplex | Half-duplex |
| Logic Technology | BiCMOS | BiCMOS | BiCMOS | BiCMOS | BiCMOS |
| RS-485 Bus Load | 1 unit load; up to 32 transceivers | 1 unit load; up to 32 transceivers | 1 unit load; up to 32 transceivers | 1 unit load; up to 32 transceivers | 1 unit load; up to 32 transceivers |
Diferensiator Kunci
- Controlled-edge B-series selection (vsISL8485ABZ-T)
- Shared 8-pin SOIC interface family (vsISL8485CBZ-T)
- Established ISL8485 receiver architecture (vsISL8490IBZ-T)
Catatan Desain
Place the 5 V decoupling capacitor immediately adjacent to the transceiver supply pins and connect it directly into the ground reference used by the driver and receiver. Keep the differential pair routed as a coupled pair over a continuous reference plane, avoid routing it across switching-power stages, and minimize vias and stubs. These steps reduce common-mode excursions and improve the likelihood of consistent operation across temperature and cable conditions.
Ensure the bus controller never enables the driver while another node is transmitting. Receiver-enable and driver-enable timing should also prevent contention at the beginning and end of a packet. Follow the family datasheet for the recommended logic truth table, and verify the IB variant's transition-rate behavior against the required cable length and emissions limit rather than treating every 5 Mbps family member as electrically interchangeable.
Termination, fail-safe biasing, and common-mode protection are part of the complete RS-485 interface, not optional bus details. Apply termination only at the physical ends of the selected cable segment and confirm that the resulting differential voltage remains within the receiver's allowed range. For cabinets containing variable-speed drives or switching supplies, evaluate common-mode transients, surge exposure, and chassis-to-circuit grounding to prevent false transitions or damage.
Informasi Konformitas
No specific compliance declarations were identified for the exact ISL8485IB-T ordering code. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status with Renesas for the current lot and package configuration.