Renesas Electronics

ISL8485IB-T - 5V 5Mbps RS-485/RS-422 Transceiver | Renesas

N.º da peça: ISL8485IB-T ✓ Ativo
4.5 V to 5.5 V Vdss RS-485 and RS-422 Rds(on) 8-pin SOIC Package
MOQ: 1 |

ISL8485IB-T Visão geral

The Renesas ISL8485IB-T is a 5 V, low-power, half-duplex RS-485/RS-422 interface transceiver with a maximum data rate of 5 Mbps, packaged in an 8-pin SOIC. It provides one driver and one receiver for balanced serial communications and operates from a 4.5 V to 5.5 V supply, allowing operation with conventional 5 V power rails that may vary by 10%.

An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals to and from differential balanced pairs. The RS-485 standard supports multipoint buses and longer interconnects with excellent noise immunity, while RS-422 provides a point-to-point differential interface. The ISL8485 family is specified as a BiCMOS single-transceiver solution that can satisfy both interface types, making it useful where field buses, industrial controllers, and instrumentation share a common physical layer.

The ISL8485IB-T operates from 4.5 V to 5.5 V and supports data rates up to 5 Mbps. It presents one unit load to an RS-485 bus, allowing up to 32 transceivers on the network when system loading and cabling conditions permit. Its half-duplex architecture reduces the number of external interface signals, while the 8-pin SOIC package supports compact surface-mount implementations.

The BiCMOS architecture combines bipolar and CMOS characteristics to support the drive and receive functions required by balanced communication links. The device family includes high-speed and slew-rate-limited operating choices, so the appropriate variant should be selected according to edge-rate requirements, cable length, topology, and electromagnetic-emissions constraints. The IB designation identifies the slew-rate-limited family option rather than the fastest A-series option.

Typical uses include industrial RS-485 field-bus links, building-control networks, factory equipment interfaces, data-acquisition systems, instrumentation, and communications equipment requiring a compact 5 V differential transceiver. Selection should account for bus direction control, termination, biasing, grounding, and the number of nodes connected to the same cable segment.

For a new PCB, place the transceiver and its decoupling capacitor close to the supply pins, connect the differential pair as a controlled-impedance route, and keep the driver, receiver, and connector ground references in one continuous plane. Add termination only where required by the network topology and verify common-mode voltage, stub length, and radiated emissions in the final equipment.

This product page combines the ISL8485 family electrical characteristics with package guidance, application analysis, and a parameter-focused comparison of compatible Renesas transceiver options. It is intended to help engineers narrow the choice before completing board-level timing, emissions, and fault-tolerance validation.

Alternativas drop-in para ISL8485IB-T — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.

Variantes desta série

Modelos da mesma série compatíveis como drop-in com ISL8485IB-T (mesmo formato e footprint) — diferindo em Transceiver Configuration.

Renesas Electronics
Transceiver Configuration: 1 transmitter and 1 receiver
Comparar com ISL8485IB-T →

ISL8485IBZ-T

✅ Drop-In
📦 8-pin SOIC
Same 4.5 V to 5.5 V supply, 5 Mbps data rate, and half-duplex RS-485/RS-422 function; ordering suffix must be checked for temperature grade and reel format

📋 Alternativa de referência (fora do catálogo)

ISL8485ABZ-T

✅ Drop-In ⚠️ Especificações não verificadas
📦 8-pin SOIC
Same 4.5 V to 5.5 V supply and 5 Mbps family rating, but the A-series version uses the high-speed drive option rather than the B-series slew-rate-limited option

📋 Alternativa de referência (fora do catálogo)

ISL8485CBZ-T

✅ Drop-In ⚠️ Especificações não verificadas
📦 8-pin SOIC
Same 4.5 V to 5.5 V supply, 5 Mbps family capability, and RS-485/RS-422 function; C-series control and timing configuration must be checked

📋 Alternativa de referência (fora do catálogo)

ISL8490IBZ-T

✅ Drop-In ⚠️ Especificações não verificadas
📦 8-pin SOIC
Same 4.5 V to 5.5 V supply and 5 Mbps family capability, but the ISL8490 uses a different receiver circuit arrangement from the ISL8485

📋 Alternativa de referência (fora do catálogo)

ISL8491IBZ-T

✅ Drop-In ⚠️ Especificações não verificadas
📦 8-pin SOIC
Same 4.5 V to 5.5 V supply and 5 Mbps family capability, but the ISL8491 receiver and enable implementation differ from the ISL8485

📋 Alternativa de referência (fora do catálogo)

ISL8485IB-T Especificações

Product Type Single RS-485/RS-422 transceiver
Transceiver Configuration 1 driver and 1 receiver
Duplex Mode Half-duplex
Supply Voltage Range 4.5 V to 5.5 V
Nominal Supply Voltage 5 V
Maximum Data Rate 5 Mbps
Interface Standards RS-485 and RS-422
Logic Technology BiCMOS
RS-485 Bus Load 1 unit load
Maximum RS-485 Transceiver Count 32 transceivers
Encapsulamento 8-pin SOIC
Package Width 3.90 mm
Tipo de montagem Surface mount
RoHS Compliance unknown
REACH Compliance unknown
AEC-Q100 Qualification unknown

Guia de Configuração de Pinos do ISL8485IB-T 3.90 mm

Configuração de pinos para ISL8485IB-T (pacote 3.90 mm). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.

Diagrama de pinagem do pacote 3.90 mm para ISL8485IB-T

Nenhum dado detalhado de pinagem disponível para ISL8485IB-T.

Consulte a ficha técnica para a configuração completa dos pinos.

Aplicações típicas

ISL8485IB-T é adequado para 6 aplicaçãos: Industrial RS-485 Field Bus, Building Automation Controller, Data Acquisition Equipment, Factory Equipment Interface, Instrumentation and Test Equipment, Point-to-Point RS-422 Link.

🏭

Industrial RS-485 Field Bus

The ISL8485IB-T suits industrial field-bus nodes that require a 5 V differential interface and up to 5 Mbps capability. Its one-unit-load RS-485 presentation allows as many as 32 transceivers on a network when the physical topology permits. The slew-rate-limited B-series choice can reduce unwanted fast-edge activity on industrial wiring, although the final cable length, topology, and emissions requirements must determine whether it is preferable to the high-speed A-series option.

🏭

Building Automation Controller

The ISL8485IB-T can connect a building-control controller to balanced RS-485 networks carrying sensor, actuator, and supervisory data. Its 4.5 V to 5.5 V operating range matches regulated 5 V controller rails, while the half-duplex arrangement reduces interface logic compared with a full-duplex design. Designers should use a continuous ground reference, suitable bus biasing, and termination appropriate to the cable topology to preserve signal integrity over the installed distance.

🧩

Data Acquisition Equipment

The ISL8485IB-T is appropriate for data-acquisition equipment that exchanges measurements over an RS-485 or RS-422 balanced link. The one-driver, one-receiver arrangement supports half-duplex communication while the family data-rate ceiling of 5 Mbps provides ample margin for many digitized sensor streams. The receiver must be enabled only when the bus is not being driven, and cable routing should minimize stub lengths and maintain a common ground reference for reliable operation.

⚡

Factory Equipment Interface

The ISL8485IB-T provides a compact physical layer for factory equipment controllers, motor-support modules, and remote I/O nodes. Its 8-pin SOIC package preserves board area, while the 4.5 V to 5.5 V supply range accommodates conventional 5 V logic. In equipment cabinets with long cables or adjacent switching power converters, the slew-rate-limited selection should be checked against emissions limits, termination strategy, and the timing requirements of the master controller.

🔧

Instrumentation and Test Equipment

The ISL8485IB-T is useful in instrumentation that communicates through a robust differential port while retaining a compact 5 V implementation. Its one-unit-load RS-485 behavior allows several instruments or nodes to share a bus, subject to the documented 32-transceiver maximum and physical-layer design. The slew-rate-limited option can be advantageous on external cables where controlled transition rates help limit high-frequency content, but interoperability and receiver timing must be verified with every connected device.

🌐

Point-to-Point RS-422 Link

The ISL8485IB-T can implement an RS-422 point-to-point link when a system prefers the same physical transceiver family used for RS-485 nodes. The 5 V supply and one-unit-load interface simplify integration with 5 V controllers, and the family's 5 Mbps rating supports moderately high-speed command or monitoring traffic. Because the device is also used in half-duplex RS-485 networks, the application must provide correct driver-enable and receiver-enable control while also observing the RS-422 termination arrangement.

What is the ISL8485IB-T?
The ISL8485IB-T is a 5 V, half-duplex RS-485/RS-422 transceiver with one driver and one receiver in an 8-pin SOIC package. According to the Renesas ISL8485, ISL8490 and ISL8491 datasheet, the family is a BiCMOS 5 V single-transceiver solution supporting data rates up to 5 Mbps and supply voltages from 4.5 V to 5.5 V.
What is the operating voltage of ISL8485IB-T?
The ISL8485IB-T operates from 4.5 V to 5.5 V, equivalent to a nominal 5 V rail with 10% tolerance. The Renesas family datasheet specifically identifies this supply range as a family-level feature, allowing use with conventional regulated 5 V supplies whose actual voltage may vary across the allowable tolerance band.
What is the maximum data rate of ISL8485IB-T?
The ISL8485IB-T supports data rates up to 5 Mbps as part of the ISL8485 transceiver family. The Renesas family datasheet identifies 5 Mbps as the maximum data rate for the ISL8485, ISL8490 and ISL8491 devices, although the IB variant is the slew-rate-limited option and should be evaluated against the required bus length and emissions target.
Where can I download the ISL8485IB-T datasheet PDF?
The official Renesas ISL8485, ISL8490 and ISL8491 datasheet is available from the manufacturer's document page at https://www.renesas.com/en/document/dst/isl8485-isl8490-isl8491-datasheet. It contains the shared electrical characteristics, timing information, interface descriptions, and application details needed to select and implement the correct ISL8485 variant.
Where can I find the ISL8485IB-T pinout?
The ISL8485IB-T pin assignment is shown in the pin-description diagram of the official Renesas ISL8485, ISL8490 and ISL8491 datasheet. Use that diagram to assign the supply, ground, driver, receiver, enable-control, and differential bus connections before laying out the 8-pin SOIC footprint and its bypass capacitor.
Is the ISL8485IB-T the same as ISL8485IBZ-T?
The ISL8485IB-T and ISL8485IBZ-T identify closely related ISL8485IB configurations, but the ordering suffixes must be checked against the current Renesas part-number table. The official product page identifies ISL8485IBZ-T as the 5 V, half-duplex, 5 Mbps RS-485/RS-422 option. Confirm the package, tape-and-reel format, temperature grade, and marking before treating either ordering code as a production substitute.
ISL8485IB-T vs ISL8490IBZ-T: which is better for an RS-485 bus?
Choose the ISL8485IB-T when its documented slew-rate behavior matches the required bus; choose ISL8490IBZ-T only after confirming its receiver and bus-loading characteristics satisfy the application. Both belong to the Renesas 4.5 V to 5.5 V family with operation up to 5 Mbps, but the ISL8485 and ISL8490 use different circuit arrangements, so their receiver implementation and system-level behavior must be compared in the family datasheet.
When should I choose ISL8485IB-T over ISL8485ABZ-T?
Choose the ISL8485IB-T when controlled transition rates or reduced switching activity are more valuable than the fastest drive performance of the A-series option. The ISL8485 family includes high-speed and slew-rate-limited versions, and the B designation represents the slew-rate-limited choice. The final decision should consider cable length, topology, EMI requirements, and the receiver timing needed by the connected equipment.
What is the best drop-in replacement for ISL8485IB-T?
The closest documented Renesas family candidate is the ISL8485IBZ-T because it shares the 5 V, half-duplex, 5 Mbps RS-485/RS-422 description and 8-pin SOIC format. Before substitution, verify enable polarity, receiver enable timing, slew rate, temperature grade, marking, and supply tolerances. The Request a Quote form on this page can be used to check availability and obtain a formal sourcing response.
Can ISL8485CBZ-T replace ISL8485IB-T?
The ISL8485CBZ-T may be considered only after a complete pin and timing comparison because the C-series configuration can differ in its control interface. The Renesas family datasheet identifies both parts as 8-pin, 5 V RS-485/RS-422 transceivers, but an exact drop-in decision requires confirming driver-enable polarity, receiver-enable behavior, propagation delay, and bus loading. Request a Quote for availability of the exact ordered MPN.
How many RS-485 nodes can connect to the ISL8485IB-T?
The ISL8485IB-T presents one unit load to an RS-485 bus, allowing up to 32 transceivers on the network under the stated family conditions. The Renesas family datasheet explicitly identifies the one-unit-load behavior and 32-transceiver capability. Actual field deployments must also satisfy cable length, topology, termination, biasing, and signal-integrity constraints.
Where can I buy ISL8485IB-T online?
Use the Request a Quote form on this page to request the ISL8485IB-T, current lead time, stock status, and order quantity. The ordered device is an 8-pin SOIC RS-485/RS-422 transceiver from Renesas Electronics. Providing the required quantity and target date in the form allows the sourcing team to return a product-specific quotation without relying on generic marketplace availability.
What is the price of ISL8485IB-T?
Current pricing for the ISL8485IB-T is handled through the Request a Quote form on this page because quote-based sourcing can change with quantity, availability, and order configuration. The form supports a product-specific response for the exact ISL8485IB-T ordering code, including its 8-pin SOIC packaging and required quantity.
What is the lead time for ISL8485IB-T?
The current lead time for ISL8485IB-T should be confirmed through the Request a Quote form on this page. Submit the required order quantity, desired shipment date, and packaging requirements so the sourcing team can check the exact ordering code rather than infer availability from a related family member or a different package suffix.
Is ISL8485IB-T in stock?
Stock status for the exact ISL8485IB-T should be confirmed through the Request a Quote form on this page. Include the quantity required and whether tape-and-reel production quantities are acceptable. This provides a direct response for the specified Renesas ordering code and avoids treating availability of a related ISL8485 variant as confirmation of stock.

Dados de referência de engenharia para ISL8485IB-T — comparação, orientação de projeto e informações de conformidade.

Guia de seleção

Choose the ISL8485IB-T for a 5 V half-duplex RS-485 or RS-422 node when controlled transition rates are preferable to the fastest edge rate of the A-series option. Choose ISL8485ABZ-T when short, low-loss links require the high-speed configuration and emissions testing confirms compliance. Choose ISL8485CBZ-T only after checking its control-interface and timing behavior against the existing PCB. Choose ISL8490IBZ-T or ISL8491IBZ-T when their different receiver architectures provide a functional advantage, while preserving the 8-pin SOIC footprint and 4.5 V to 5.5 V operating range. ISL8485IBZ-T is the closest ordering-code candidate for a production substitution, but the exact suffix, temperature grade, reel format, enable polarity, and marking must be confirmed before approval.

Comparação com alternativas

Parâmetro Este produto ISL8485IBZ-T ISL8485ABZ-T ISL8485CBZ-T ISL8490IBZ-T
Brand Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics
Package 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC
Product Type RS-485/RS-422 transceiver RS-485/RS-422 transceiver RS-485/RS-422 transceiver RS-485/RS-422 transceiver RS-485/RS-422 transceiver
Nominal Supply Voltage 5 V 5 V 5 V 5 V 5 V
Supply Voltage Range 4.5 V to 5.5 V 4.5 V to 5.5 V 4.5 V to 5.5 V 4.5 V to 5.5 V 4.5 V to 5.5 V
Maximum Data Rate 5 Mbps 5 Mbps 5 Mbps 5 Mbps 5 Mbps
Duplex Mode Half-duplex Half-duplex Half-duplex Half-duplex Half-duplex
Logic Technology BiCMOS BiCMOS BiCMOS BiCMOS BiCMOS
RS-485 Bus Load 1 unit load; up to 32 transceivers 1 unit load; up to 32 transceivers 1 unit load; up to 32 transceivers 1 unit load; up to 32 transceivers 1 unit load; up to 32 transceivers

Principais diferenciais

  • Controlled-edge B-series selection (vs ISL8485ABZ-T)
  • Shared 8-pin SOIC interface family (vs ISL8485CBZ-T)
  • Established ISL8485 receiver architecture (vs ISL8490IBZ-T)

Notas de projeto

Place the 5 V decoupling capacitor immediately adjacent to the transceiver supply pins and connect it directly into the ground reference used by the driver and receiver. Keep the differential pair routed as a coupled pair over a continuous reference plane, avoid routing it across switching-power stages, and minimize vias and stubs. These steps reduce common-mode excursions and improve the likelihood of consistent operation across temperature and cable conditions.

Ensure the bus controller never enables the driver while another node is transmitting. Receiver-enable and driver-enable timing should also prevent contention at the beginning and end of a packet. Follow the family datasheet for the recommended logic truth table, and verify the IB variant's transition-rate behavior against the required cable length and emissions limit rather than treating every 5 Mbps family member as electrically interchangeable.

Termination, fail-safe biasing, and common-mode protection are part of the complete RS-485 interface, not optional bus details. Apply termination only at the physical ends of the selected cable segment and confirm that the resulting differential voltage remains within the receiver's allowed range. For cabinets containing variable-speed drives or switching supplies, evaluate common-mode transients, surge exposure, and chassis-to-circuit grounding to prevent false transitions or damage.

Informações de conformidade

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Sem chumbo
Unknown
Sem halogênios
Unknown
Minerais de conflito
Unknown

No specific compliance declarations were identified for the exact ISL8485IB-T ordering code. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status with Renesas for the current lot and package configuration.

Dados verificados em: 2026-11-20 — dados verificados e curados pela equipe de engenharia de componentes da XAIPART

Buscas relacionadas

ISL8485IB-T ISL8485IB-T datasheet ISL8485IB-T datasheet pdf ISL8485IB-T pinout ISL8485IB-T schematic ISL8485IB-T equivalent ISL8485IB-T replacement ISL8485IB-T cross reference ISL8485IB-T vs ISL8490IBZ-T Renesas ISL8485IB-T ISL8485IB-T price ISL8485IB-T stock 8-SOIC RS-485 transceiver 5Mbps RS-422 transceiver

Componentes & termos relacionados

Renesas Electronics ISL8485IB-T ISL8485IBZ-T ISL8485ABZ-T ISL8485CBZ-T ISL8490IBZ-T ISL8491IBZ-T RS-485 RS-422 half-duplex transceiver differential interface BiCMOS 5 Mbps 4.5 V to 5.5 V one unit load 32-transceiver network 8-pin SOIC SOIC family surface-mount package slew-rate-limited industrial field bus building automation data acquisition common-mode voltage
RFQ de cotação rápida
Preencha todos os detalhes — nossa equipe de vendas responderá em até 24 horas
Part number Fabricante Encapsulamento QTY Preço-alvo Total
✓
Cotação enviada!

Responderemos seu e-mail em até 24 horas

1
RFQ enviada
2
Cotação recebida
3
Pedido realizado
4
Pagamento
5
Enviado
6
Entregue
Ver detalhes da RFQ