ISL8485IB-T - 5V 5Mbps RS-485/RS-422 Transceiver | Renesas
MPN: ISL8485IB-T ✓ 啟用中ISL8485IB-T 概覽
An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals to and from differential balanced pairs. The RS-485 standard supports multipoint buses and longer interconnects with excellent noise immunity, while RS-422 provides a point-to-point differential interface. The ISL8485 family is specified as a BiCMOS single-transceiver solution that can satisfy both interface types, making it useful where field buses, industrial controllers, and instrumentation share a common physical layer.
The ISL8485IB-T operates from 4.5 V to 5.5 V and supports data rates up to 5 Mbps. It presents one unit load to an RS-485 bus, allowing up to 32 transceivers on the network when system loading and cabling conditions permit. Its half-duplex architecture reduces the number of external interface signals, while the 8-pin SOIC package supports compact surface-mount implementations.
The BiCMOS architecture combines bipolar and CMOS characteristics to support the drive and receive functions required by balanced communication links. The device family includes high-speed and slew-rate-limited operating choices, so the appropriate variant should be selected according to edge-rate requirements, cable length, topology, and electromagnetic-emissions constraints. The IB designation identifies the slew-rate-limited family option rather than the fastest A-series option.
Typical uses include industrial RS-485 field-bus links, building-control networks, factory equipment interfaces, data-acquisition systems, instrumentation, and communications equipment requiring a compact 5 V differential transceiver. Selection should account for bus direction control, termination, biasing, grounding, and the number of nodes connected to the same cable segment.
For a new PCB, place the transceiver and its decoupling capacitor close to the supply pins, connect the differential pair as a controlled-impedance route, and keep the driver, receiver, and connector ground references in one continuous plane. Add termination only where required by the network topology and verify common-mode voltage, stub length, and radiated emissions in the final equipment.
This product page combines the ISL8485 family electrical characteristics with package guidance, application analysis, and a parameter-focused comparison of compatible Renesas transceiver options. It is intended to help engineers narrow the choice before completing board-level timing, emissions, and fault-tolerance validation.
直接替換替代品,適用於 ISL8485IB-T — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: ISL8485IB-T (相同外形與佔位) — 差異在於 Transceiver Configuration.
ISL8485IBZ-T
✅ 直接替換📋 參考替代品(不在目錄中)
ISL8485ABZ-T
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
ISL8485CBZ-T
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
ISL8490IBZ-T
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
ISL8491IBZ-T
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
ISL8485IB-T 規格
| Product Type | Single RS-485/RS-422 transceiver |
| Transceiver Configuration | 1 driver and 1 receiver |
| Duplex Mode | Half-duplex |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Nominal Supply Voltage | 5 V |
| Maximum Data Rate | 5 Mbps |
| Interface Standards | RS-485 and RS-422 |
| Logic Technology | BiCMOS |
| RS-485 Bus Load | 1 unit load |
| Maximum RS-485 Transceiver Count | 32 transceivers |
| 封裝 | 8-pin SOIC |
| Package Width | 3.90 mm |
| 安裝類型 | Surface mount |
| RoHS Compliance | unknown |
| REACH Compliance | unknown |
| AEC-Q100 Qualification | unknown |
ISL8485IB-T 3.90 mm 腳位配置指南
ISL8485IB-T(3.90 mm 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: ISL8485IB-T.
請參閱 資料表 以查看完整腳位配置。
典型應用
ISL8485IB-T 適用於 6 應用s: Industrial RS-485 Field Bus, Building Automation Controller, Data Acquisition Equipment, Factory Equipment Interface, Instrumentation and Test Equipment, Point-to-Point RS-422 Link.
Industrial RS-485 Field Bus
The ISL8485IB-T suits industrial field-bus nodes that require a 5 V differential interface and up to 5 Mbps capability. Its one-unit-load RS-485 presentation allows as many as 32 transceivers on a network when the physical topology permits. The slew-rate-limited B-series choice can reduce unwanted fast-edge activity on industrial wiring, although the final cable length, topology, and emissions requirements must determine whether it is preferable to the high-speed A-series option.
推薦
Building Automation Controller
The ISL8485IB-T can connect a building-control controller to balanced RS-485 networks carrying sensor, actuator, and supervisory data. Its 4.5 V to 5.5 V operating range matches regulated 5 V controller rails, while the half-duplex arrangement reduces interface logic compared with a full-duplex design. Designers should use a continuous ground reference, suitable bus biasing, and termination appropriate to the cable topology to preserve signal integrity over the installed distance.
推薦
Data Acquisition Equipment
The ISL8485IB-T is appropriate for data-acquisition equipment that exchanges measurements over an RS-485 or RS-422 balanced link. The one-driver, one-receiver arrangement supports half-duplex communication while the family data-rate ceiling of 5 Mbps provides ample margin for many digitized sensor streams. The receiver must be enabled only when the bus is not being driven, and cable routing should minimize stub lengths and maintain a common ground reference for reliable operation.
推薦
Factory Equipment Interface
The ISL8485IB-T provides a compact physical layer for factory equipment controllers, motor-support modules, and remote I/O nodes. Its 8-pin SOIC package preserves board area, while the 4.5 V to 5.5 V supply range accommodates conventional 5 V logic. In equipment cabinets with long cables or adjacent switching power converters, the slew-rate-limited selection should be checked against emissions limits, termination strategy, and the timing requirements of the master controller.
推薦
Instrumentation and Test Equipment
The ISL8485IB-T is useful in instrumentation that communicates through a robust differential port while retaining a compact 5 V implementation. Its one-unit-load RS-485 behavior allows several instruments or nodes to share a bus, subject to the documented 32-transceiver maximum and physical-layer design. The slew-rate-limited option can be advantageous on external cables where controlled transition rates help limit high-frequency content, but interoperability and receiver timing must be verified with every connected device.
推薦
Point-to-Point RS-422 Link
The ISL8485IB-T can implement an RS-422 point-to-point link when a system prefers the same physical transceiver family used for RS-485 nodes. The 5 V supply and one-unit-load interface simplify integration with 5 V controllers, and the family's 5 Mbps rating supports moderately high-speed command or monitoring traffic. Because the device is also used in half-duplex RS-485 networks, the application must provide correct driver-enable and receiver-enable control while also observing the RS-422 termination arrangement.
推薦
推薦產品摘要
工程參考資料,適用於 ISL8485IB-T — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | ISL8485IBZ-T | ISL8485ABZ-T | ISL8485CBZ-T | ISL8490IBZ-T |
|---|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Product Type | RS-485/RS-422 transceiver | RS-485/RS-422 transceiver | RS-485/RS-422 transceiver | RS-485/RS-422 transceiver | RS-485/RS-422 transceiver |
| Nominal Supply Voltage | 5 V | 5 V | 5 V | 5 V | 5 V |
| Supply Voltage Range | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V |
| Maximum Data Rate | 5 Mbps | 5 Mbps | 5 Mbps | 5 Mbps | 5 Mbps |
| Duplex Mode | Half-duplex | Half-duplex | Half-duplex | Half-duplex | Half-duplex |
| Logic Technology | BiCMOS | BiCMOS | BiCMOS | BiCMOS | BiCMOS |
| RS-485 Bus Load | 1 unit load; up to 32 transceivers | 1 unit load; up to 32 transceivers | 1 unit load; up to 32 transceivers | 1 unit load; up to 32 transceivers | 1 unit load; up to 32 transceivers |
主要差異化特點
- Controlled-edge B-series selection (對比ISL8485ABZ-T)
- Shared 8-pin SOIC interface family (對比ISL8485CBZ-T)
- Established ISL8485 receiver architecture (對比ISL8490IBZ-T)
設計說明
Place the 5 V decoupling capacitor immediately adjacent to the transceiver supply pins and connect it directly into the ground reference used by the driver and receiver. Keep the differential pair routed as a coupled pair over a continuous reference plane, avoid routing it across switching-power stages, and minimize vias and stubs. These steps reduce common-mode excursions and improve the likelihood of consistent operation across temperature and cable conditions.
Ensure the bus controller never enables the driver while another node is transmitting. Receiver-enable and driver-enable timing should also prevent contention at the beginning and end of a packet. Follow the family datasheet for the recommended logic truth table, and verify the IB variant's transition-rate behavior against the required cable length and emissions limit rather than treating every 5 Mbps family member as electrically interchangeable.
Termination, fail-safe biasing, and common-mode protection are part of the complete RS-485 interface, not optional bus details. Apply termination only at the physical ends of the selected cable segment and confirm that the resulting differential voltage remains within the receiver's allowed range. For cabinets containing variable-speed drives or switching supplies, evaluate common-mode transients, surge exposure, and chassis-to-circuit grounding to prevent false transitions or damage.
合規資訊
No specific compliance declarations were identified for the exact ISL8485IB-T ordering code. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status with Renesas for the current lot and package configuration.