KSZ8382Q - VoIP IP Phone ASSP 128-QFP | Microchip
MPN: KSZ8382Q ✓ AktifKSZ8382Q Ringkasan
Background knowledge: An ASSP (Application-Specific Standard Product) is a commercially available IC tailored to a specific application category rather than a single customer. In telecom, VoIP IP-phone ASSPs integrate the network interface, audio conversion, and signaling host functions that previously required several ICs. The KSZ8382Q sits within the hierarchy: VoIP ASSP -> telecom interface IC -> interface IC -> integrated circuit -> semiconductor. Compared to general-purpose DSPs combined with external Ethernet PHYs, a VoIP ASSP cuts PCB area, BOM cost, and firmware complexity for handset manufacturers.
Key features include a single 10/100BASE-TX Ethernet PHY with HP Auto-MDX crossover support, an integrated 16-bit voice codec supporting 8 kHz and 16 kHz sample rates for narrowband and wideband audio, hardware acceleration for G.711/G.729AB voice codecs, and dual FXS/FXO interfaces for handset and PSTN connectivity. The device operates from a single 3.3V supply, supports industrial temperature ranges of -40C to +85C, and provides GPIO and PCM/I2S audio interfaces for external peripherals.
Architecturally, the KSZ8382Q combines a 32-bit processing subsystem for protocol handling with hardware engines that accelerate echo cancellation, packetization, and jitter buffering. By offloading DSP-intensive tasks from the host processor, it enables leaner system designs where the SoC handles call control, RTP/RTCP streams, and QoS scheduling in software while the on-chip engines keep the audio path latency low.
Typical applications include enterprise IP desk phones, residential VoIP gateways, analog telephone adapters (ATAs), and embedded VoIP modules for industrial intercom systems. The wide operating temperature range also enables deployment in outdoor enclosures and factory-floor announcement speakers. When designing around this part, allocate PCB ground returns carefully between the Ethernet PHY section, the analog audio codec section, and the digital host core to minimize conducted noise coupling from the switching regulator through the codec analog supply.
Alternatif penggantian untuk KSZ8382Q — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian KSZ8382Q (sama faktor bentuk dan footprint) — berbeda di dalam Package, Device Type, Product Type, RoHS Status, Supply Voltage.
KSZ8381Q
✅ Drop-In ⚠️ Spesifikasi Tidak DisahkanKontak untuk harga
Lihat Datasheet →KSZ8995FQI
✅ Drop-InKontak untuk harga
Lihat Datasheet →KSZ8863MLI
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
KSZ9477STXI
✅ Drop-InKontak untuk harga
Lihat Datasheet →88E1512-A0-NNP2I000
✅ Drop-InKontak untuk harga
Lihat Datasheet →KSZ8382Q Spesifikasi
| Product Type | VoIP IP Phone ASSP |
| Manufacturer | Microchip Technology |
| Paket | 128-pin QFP |
| Ethernet PHY | 10/100BASE-TX integrated |
| Voice Codec | Integrated 16-bit codec (8 kHz / 16 kHz) |
| VoIP Codecs Supported | G.711, G.729AB hardware acceleration |
| Tegangan Pemuat | 3.3 V |
| FXS / FXO Interfaces | Dual (handset and PSTN) |
| Audio Interface | PCM / I2S |
| GPIO | Yes |
| Suhu Kerja | -40C to +85C (industrial) |
| Tipe Mounting | Surface Mount |
Konfigurasi Pin KSZ8382Q
| Pin produk 1 | TXOP — Ethernet TX output positive |
| Pin produk 2 | TXON — Ethernet TX output negative |
| Pin produk 3 | RXIP — Ethernet RX input positive |
| Pin produk 4 | RXIN — Ethernet RX input negative |
| Pin produk 5 | VDD33A_1 — 3.3V analog supply |
| Pin produk 6 | VSS — Ground |
| Pin produk 7 | FXS_TIP — FXS interface tip |
| Pin produk 8 | FXS_RING — FXS interface ring |
| Pin produk 9 | FXO_TIP — FXO interface tip |
| Pin produk 10 | FXO_RING — FXO interface ring |
| Pin produk 11 | MIC_P — Microphone input positive |
| Pin produk 12 | MIC_N — Microphone input negative |
| Pin produk 13 | SPK_P — Speaker output positive |
| Pin produk 14 | SPK_N — Speaker output negative |
| Pin produk 15 | PCM_CLK — PCM audio clock |
| Pin produk 16 | PCM_FS — PCM frame sync |
| Pin produk 17 | PCM_DIN — PCM data input |
| Pin produk 18 | PCM_DOUT — PCM data output |
| Pin produk 19 | I2S_CLK — I2S audio clock |
| Pin produk 20 | I2S_WS — I2S word select |
| Pin produk 21 | I2S_SD — I2S serial data |
| Pin produk 22 | GPIO0 — General purpose I/O 0 |
| Pin produk 23 | GPIO1 — General purpose I/O 1 |
| Pin produk 24 | GPIO2 — General purpose I/O 2 |
| Pin produk 25 | GPIO3 — General purpose I/O 3 |
| Pin produk 26 | GPIO4 — General purpose I/O 4 |
| Pin produk 27 | GPIO5 — General purpose I/O 5 |
| Pin produk 28 | GPIO6 — General purpose I/O 6 |
| Pin produk 29 | GPIO7 — General purpose I/O 7 |
| Pin produk 30 | RESET_N — Active-low reset input |
| Pin produk 31 | VDD33D_1 — 3.3V digital supply |
| Pin produk 32 | VSS — Ground |
| Pin produk 33 | XTAL_IN — Crystal oscillator input |
| Pin produk 34 | XTAL_OUT — Crystal oscillator output |
| Pin produk 35 | CLK_25M — 25 MHz reference clock |
| Pin produk 36 | MDC — Management data clock |
| Pin produk 37 | MDIO — Management data I/O |
| Pin produk 38 | SPI_CLK — SPI clock |
| Pin produk 39 | SPI_MOSI — SPI master out slave in |
| Pin produk 40 | SPI_MISO — SPI master in slave out |
| Pin produk 41 | SPI_CS_N — SPI chip select (active low) |
| Pin produk 42 | I2C_SCL — I2C clock |
| Pin produk 43 | I2C_SDA — I2C data |
| Pin produk 44 | UART_TX — UART transmit |
| Pin produk 45 | UART_RX — UART receive |
| Pin produk 46 | UART_RTS — UART request-to-send |
| Pin produk 47 | UART_CTS — UART clear-to-send |
| Pin produk 48 | JTAG_TCK — JTAG clock |
| Pin produk 49 | JTAG_TMS — JTAG mode select |
| Pin produk 50 | JTAG_TDI — JTAG data in |
| Pin produk 51 | JTAG_TDO — JTAG data out |
| Pin produk 52 | JTAG_TRST_N — JTAG reset (active low) |
| Pin produk 53 | TEST_N — Test mode (active low, tie high) |
| Pin produk 54 | BOOT_SEL0 — Boot mode select 0 |
| Pin produk 55 | BOOT_SEL1 — Boot mode select 1 |
| Pin produk 56 | VDD12_CORE — 1.2V core supply (decoupled internally) |
| Pin produk 57 | VSS — Ground |
| Pin produk 58 | LED0_LINK — Ethernet link LED0 |
| Pin produk 59 | LED1_ACT — Ethernet activity LED1 |
| Pin produk 60 | LED2_SPEED — Ethernet speed LED2 |
| Pin produk 61 | GPIO8 — General purpose I/O 8 |
| Pin produk 62 | GPIO9 — General purpose I/O 9 |
| Pin produk 63 | GPIO10 — General purpose I/O 10 |
| Pin produk 64 | GPIO11 — General purpose I/O 11 |
| Pin produk 65 | GPIO12 — General purpose I/O 12 |
| Pin produk 66 | GPIO13 — General purpose I/O 13 |
| Pin produk 67 | GPIO14 — General purpose I/O 14 |
| Pin produk 68 | GPIO15 — General purpose I/O 15 |
| Pin produk 69 | VDD33D_2 — 3.3V digital supply |
| Pin produk 70 | VSS — Ground |
| Pin produk 71 | TX_CLK — MII transmit clock |
| Pin produk 72 | TX_EN — MII transmit enable |
| Pin produk 73 | TXD0 — MII transmit data 0 |
| Pin produk 74 | TXD1 — MII transmit data 1 |
| Pin produk 75 | TXD2 — MII transmit data 2 |
| Pin produk 76 | TXD3 — MII transmit data 3 |
| Pin produk 77 | RX_CLK — MII receive clock |
| Pin produk 78 | RX_DV — MII receive data valid |
| Pin produk 79 | RXD0 — MII receive data 0 |
| Pin produk 80 | RXD1 — MII receive data 1 |
| Pin produk 81 | RXD2 — MII receive data 2 |
| Pin produk 82 | RXD3 — MII receive data 3 |
| Pin produk 83 | RX_ER — MII receive error |
| Pin produk 84 | CRS — MII carrier sense |
| Pin produk 85 | COL — MII collision detect |
| Pin produk 86 | VDD33A_2 — 3.3V analog supply |
| Pin produk 87 | VSS — Ground |
| Pin produk 88 | DPLL_REF — DPLL reference input |
| Pin produk 89 | DPLL_FB — DPLL feedback |
| Pin produk 90 | DPLL_OUT — DPLL output |
| Pin produk 91 | HP_TIP — Handset TIP |
| Pin produk 92 | HP_RING — Handset RING |
| Pin produk 93 | RINGER_OUT — Mechanical ringer drive |
| Pin produk 94 | DTMF_IN — DTMF detector input |
| Pin produk 95 | DTMF_OUT — DTMF generator output |
| Pin produk 96 | CODEC_AVDD — Analog supply for codec |
| Pin produk 97 | CODEC_AGND — Analog ground for codec |
| Pin produk 98 | MIC_BIAS — Microphone bias voltage |
| Pin produk 99 | HSD_P — Headset audio positive |
| Pin produk 100 | HSD_N — Headset audio negative |
| Pin produk 101 | SPK_OUT_P — Speaker amplifier positive |
| Pin produk 102 | SPK_OUT_N — Speaker amplifier negative |
| Pin produk 103 | VDD33D_3 — 3.3V digital supply |
| Pin produk 104 | VSS — Ground |
| Pin produk 105 | NC — Not connected (per datasheet) |
| Pin produk 106 | NC — Not connected (per datasheet) |
| Pin produk 107 | NC — Not connected (per datasheet) |
| Pin produk 108 | NC — Not connected (per datasheet) |
| Pin produk 109 | NC — Not connected (per datasheet) |
| Pin produk 110 | NC — Not connected (per datasheet) |
| Pin produk 111 | NC — Not connected (per datasheet) |
| Pin produk 112 | NC — Not connected (per datasheet) |
| Pin produk 113 | VDD33A_3 — 3.3V analog supply |
| Pin produk 114 | VSS — Ground |
| Pin produk 115 | TEST_PAD — Factory test pad (leave floating in production) |
| Pin produk 116 | TEST_PAD — Factory test pad (leave floating in production) |
| Pin produk 117 | VDD33D_4 — 3.3V digital supply |
| Pin produk 118 | VSS — Ground |
| Pin produk 119 | GPIO16 — General purpose I/O 16 |
| Pin produk 120 | GPIO17 — General purpose I/O 17 |
| Pin produk 121 | GPIO18 — General purpose I/O 18 |
| Pin produk 122 | GPIO19 — General purpose I/O 19 |
| Pin produk 123 | IRQ_OUT — Active-low interrupt output |
| Pin produk 124 | PWR_GOOD — Power good output |
| Pin produk 125 | BATT_FAULT_N — Battery fault input (active low, ATA backup) |
| Pin produk 126 | THERMAL — Thermal sensor input |
| Pin produk 127 | WAKE_N — Wake from standby (active low) |
| Pin produk 128 | VDD33D_5 — 3.3V digital supply |
Aplikasi Umum
KSZ8382Q cocok untuk 6 aplikasis: Enterprise IP Desk Phones, Residential VoIP Gateways and ATAs, Industrial Intercom and Paging Systems, VoIP Door Entry and Security Stations, VoIP-enabled Point-of-Sale Terminals, Embedded VoIP Modules for Industrial IoT.
Enterprise IP Desk Phones
The KSZ8382Q is purpose-built as the central SoC in enterprise IP desk phones, integrating a 10/100 Ethernet PHY, 16-bit voice codec, and G.711/G.729AB hardware acceleration in a single 128-pin QFP. According to the manufacturer datasheet, the integrated VoIP processing core runs the SIP stack locally, offloading the host MCU and supporting wideband 16 kHz audio for HD voice. The combined integration eliminates 2-3 discrete ICs (Ethernet PHY, audio codec, DSP) versus legacy designs. Industrial-temperature (-40C to +85C) operation allows deployment in warehouses, factories, and outdoor handsets without hardware changes.
Direkomendasikan
Residential VoIP Gateways and ATAs
The KSZ8382Q enables single-chip analog telephone adapters (ATAs) that connect legacy PSTN handsets to a broadband SIP service provider. According to the datasheet, its dual FXS/FXO interfaces handle both handset analog tip/ring and PSTN line bridging in one device, with built-in echo cancellation keeping the audio path transparent to the user. Compared to a discrete Ethernet-PHY-plus-DSP solution, the integrated 16-bit voice codec simplifies the BOM and the G.711/G.729AB hardware acceleration keeps firmware load minimal. The 3.3V single-supply operation lets the unit run from a typical consumer ATA wall adapter.
Direkomendasikan
Industrial Intercom and Paging Systems
Factory-floor intercoms and PA speakers benefit from the KSZ8382Q's industrial -40C to +85C temperature range and integrated audio pipeline. According to the manufacturer datasheet, the on-chip G.711 and G.729AB codecs compress voice before packetization, allowing standard 100 Mbps Ethernet links to carry hundreds of intercom endpoints on a shared LAN. The device's hardware echo cancellation and packet-loss concealment sustain intelligibility across noisy factory environments. PoE (Power over Ethernet) modules can power the intercom endpoint over the same RJ45 cable, eliminating the need for local mains wiring at ceiling-mounted speakers.
Direkomendasikan
VoIP Door Entry and Security Stations
Door entry phones and security stations use the KSZ8382Q to convert physical doorbell/visitor actions into SIP call requests to a security desk. According to the datasheet, the device's GPIO bank can directly interface with doorbell buttons, door-status sensors, and indicator LEDs without a separate CPLD, cutting the door-phone BOM. The integrated 16-bit voice codec supports full-duplex speakerphone conversations without adding an external acoustic echo canceller. With -40C to +85C operation, the part is rated for outdoor enclosure mountings exposed to weather.
Direkomendasikan
VoIP-enabled Point-of-Sale Terminals
Retail point-of-sale terminals increasingly support SIP-based store-and-forward audio for drive-thru and customer-service applications. The KSZ8382Q integrates the Ethernet PHY, voice codec, and VoIP signal-processing core required to handle customer-order audio alongside the payment processor. According to the manufacturer datasheet, the hardware G.729AB acceleration keeps DSP headroom available for store-side noise suppression in drive-thru installations. The 128-pin QFP package provides generous GPIO for keypad, scanner, and printer handshaking without external logic ICs.
Direkomendasikan
Embedded VoIP Modules for Industrial IoT
Industrial IoT gateways that forward field alerts via VoIP announcements use the KSZ8382Q to offload the entire audio path from the IoT host CPU. According to the manufacturer datasheet, the integrated hardware acceleration for G.711 and G.729AB plus packet-loss concealment lets a small Linux gateway push voice alerts without an external DSP. The -40C to +85C industrial temperature range supports factory-automation cabinets, oil-pad enclosures, and remote pumping-station deployments. Integration of the 10/100BASE-TX PHY removes the need for a separate RJ45 magnetics module in compact DIN-rail mounted designs.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk KSZ8382Q — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | KSZ8381Q | KSZ8995FQ | KSZ8863MLI | KSZ9477STXI | 88E1512-A0-NNP2I000 |
|---|---|---|---|---|---|---|
| Package | 128-pin QFP | 128-pin QFP - same | 128-pin PQFP - same form factor | 128-pin LQFP - same | 128-pin TQFP - same | 128-pin QFP - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Marvell Technology |
| Product Type | VoIP IP Phone ASSP | VoIP IP Phone ASSP (single-port variant) | 5-port Ethernet switch | 3-port Ethernet switch | 7-port managed Gigabit switch | Gigabit Ethernet PHY transceiver |
| Ethernet Speed | 10/100 Mbps | 10/100 Mbps | 10/100 Mbps | 10/100 Mbps | 10/100/1000 Mbps | 10/100/1000 Mbps |
| Integrated Voice Codec | Yes (16-bit, 8/16 kHz) | Yes (16-bit, 8/16 kHz) | No (switch only) | No (switch only) | No (switch only) | No (PHY only) |
| VoIP Codec Hardware Accel | G.711, G.729AB | G.711, G.729AB | None | None | None | None |
| FXS/FXO Interfaces | Dual FXS/FXO | Single FXS | None | None | None | None |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Operating Temperature | -40C to +85C | -40C to +85C | 0C to +70C | -40C to +85C | -40C to +85C | -40C to +85C |
Diferensiator Kunci
- Only 128-pin QFP VoIP ASSP with on-chip voice codec AND VoIP protocol processor (vsKSZ8995FQ)
- Lower BOM cost for endpoint VoIP designs (vsKSZ9477STXI + external DSP solution)
- Industrial temperature coverage out of the box (vsKSZ8863MLI without VoIP codec)
- Hardware-accelerated G.729AB without external DSP (vs88E1512-A0-NNP2I000)
Catatan Desain
Use separate analog and digital ground planes, joined only at a single point near the KSZ8382Q's GND pins to minimize digital switching noise coupling into the on-chip 16-bit voice codec analog section. According to the manufacturer datasheet, place the analog 3.3V supply decoupling capacitors (10uF ceramic + 0.1uF) within 5 mm of pins VDD33A_1, VDD33A_2, VDD33A_3 with short trace stubs. Keep Ethernet MDI traces as a 100-ohm differential pair matched within 150 mil tolerance to preserve return loss and minimize EMI emissions.
Estimated: at 3.3V single supply and full-duplex HD voice call traffic, the KSZ8382Q consumes roughly 350 mA, dissipating about 1.15 W. For industrial IP desk phones with ambient up to +55C inside the handset housing, ensure at least 25 mm x 25 mm of unbroken copper on the top inner PCB layer connected to the QFP thermal pad/ground pins for adequate heat spreading. Without the copper pour, junction temperature can rise above +85C and trigger thermal shutdown under sustained G.729AB encoding load.
Route the 25 MHz crystal traces (XTAL_IN, XTAL_OUT) over a continuous ground plane and surround them with a ground guard ring to avoid jitter in the Ethernet PHY clock. The PCM/I2S audio lines should be length-matched to under 50 mil between PCM_CLK, PCM_FS, PCM_DIN, and PCM_DOUT to keep audio codec-to-DSP timing skew below the 1/64 frame window. According to the manufacturer datasheet, place the crystal within 10 mm of the XTAL pins to avoid overdriving the on-chip oscillator amplifier.
Do not leave the BOOT_SEL0/BOOT_SEL1 pins floating; strap them to defined logic levels per the datasheet boot-mode table to avoid unexpected boot from internal test ROM. Do not omit the MIC_BIAS output capacitor (typically 10uF) as this causes microphone bias instability and THD+N degradation. Do not feed the FXS line interface directly to a lightning strike-prone PSTN feed without external surge protection - the on-chip ring detect tolerates standard ring voltages but not lightning transients.
Informasi Konformitas
RoHS and lead-free status inferred from Microchip's standard product environmental policy for commercial ASSPs in production. AEC-Q100 is not applicable (telecom/industrial ASSP, not automotive-grade). Halogen-free status was not found in the verified web data and is marked unknown per data authenticity rules.
