LM224ADRG4 - Quad 30V 1.2MHz Op Amp | Texas Instruments
MPN: LM224ADRG4 ✓ AktifLM224ADRG4 Ringkasan
A general-purpose operational amplifier is an analog signal-conditioning IC used to amplify voltage differences, buffer sensor outputs, or implement feedback-controlled analog circuits. In the hierarchy of electronic components, an operational amplifier belongs to the amplifier IC class, the larger analog and mixed-signal IC category, and ultimately the semiconductor family. Its internal gain is frequency dependent, so closed-loop bandwidth depends on the selected feedback network and noise gain.
The LM224A family provides four amplifiers in one package, allowing a compact PCB design to implement several independent analog functions. Its 1.2 MHz gain-bandwidth product supports general-purpose signal processing rather than high-speed precision instrumentation. The specified 3 mV input offset voltage is important when signals are small or when multiple stages must operate with controlled dc error. A 30 V maximum supply rating and ±16 V or 32 V operating supply descriptions cover conventional industrial supply environments.
Each amplifier is internally frequency compensated, simplifying implementation of standard inverting, non-inverting, summing, and comparator-style signal-processing arrangements. The package pinout follows the conventional quad operational-amplifier arrangement, with power, ground, four differential inputs, and four outputs. Because input offset, bias current, common-mode range, output swing, supply current, and noise are not stated in the product listing excerpts, consult the manufacturer datasheet before finalizing precision biasing, output-swing, or stability calculations.
Typical uses include industrial control and instrumentation, four-channel sensor conditioning, audio preamplification, power-supply feedback, sample-and-hold support circuits, and general mixed-signal interfaces. The four independent channels make the device especially useful when a design needs several similar low-frequency analog stages without allocating separate single-amplifier packages.
For a new layout, route each input and output according to the manufacturer pin-description table, place input and output decoupling capacitors close to the supply pins, and verify stability with the intended feedback network and load. This page combines ordering information, verified device characteristics, drop-in family alternatives, comparison details, and practical implementation guidance for faster component selection and PCB planning.
Alternatif penggantian untuk LM224ADRG4 — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian LM224ADRG4 (sama faktor bentuk dan footprint) — berbeda di dalam Mounting Type.
LM224ADR
✅ Drop-InKontak untuk harga
Lihat Datasheet →LM224DRG4
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
LM224ADRG4 Rating Maksimal & Karakteristik Listrik
| Amplifier Type | General-purpose operational amplifier |
| Number of Circuits | 4 circuits |
| Gain-Bandwidth Product | 1.2 MHz |
| Typical Input Offset Voltage | 3 mV |
| Maximum Supply Voltage | 30 V |
| Tegangan Pemuat Kerja | ±16 V or 32 V |
| Rentang Suhu Kerja | -25°C to 85°C |
| Package Type | 14-pin SOIC (D) |
| Jumlah Pin | 14 pins |
| Tipe Mounting | Surface mount |
| Frequency Compensation | Internally compensated |
LM224ADRG4 14-pin soic (d) Diamant Konfigurasi Panduan
Konfigurasi pin untuk LM224ADRG4 (14-pin soic (d) pakai pakai). Komponen analog ini memiliki pin masukan, keluaran, dan pengirim daya. Lihat datasheet produsen untuk konfigurasi pin offset null, kompensasi, dan pengaktifan. Ideal untuk peralatan sinyal dan kabel penggandaran.
Tidak ada data diatribut pin yang tersedia untuk LM224ADRG4.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
LM224ADRG4 cocok untuk 6 aplikasis: Industrial Sensor Conditioning, Audio Preamplification, Power-Supply Feedback Monitoring, Data Acquisition Front End, Control-System Signal Conditioning, Portable Measurement Module.
Industrial Sensor Conditioning
The LM224ADRG4 is appropriate for multichannel industrial sensor conditioning because it combines four internally compensated amplifiers with a 1.2 MHz gain-bandwidth product in one 14-pin SOIC. Separate channels can amplify, invert, sum, or buffer low-bandwidth transducer signals without requiring four single-amplifier packages. Its -25°C to 85°C operating range suits equipment operating above typical room temperature, provided the complete enclosure stays within that limit. Before committing to a gain network, check sensor impedance, input common-mode voltage, output swing, and the application-specific offset error. The listed 3 mV typical input offset can be significant when the sensor produces only millivolts, so use the manufacturer electrical tables to select practical resistor values and assess calibration requirements.
Direkomendasikan
Audio Preamplification
The LM224ADRG4 can provide four low-frequency preamplifier or buffer stages for audio-oriented analog subsystems. Its 1.2 MHz gain-bandwidth product is much faster than the bandwidth generally needed for baseband audio, while the four-channel 14-pin SOIC arrangement helps reduce board area in line-level preamplifier, mixer, or headphone-driver input networks. Use each channel independently for low-impedance source buffering or non-inverting amplification, and verify the output-current capability against the next stage. The 3 mV typical input offset is generally less important for audio signals than for precision sensors but should be included in minimum-signal calculations. Confirm input bias current, output swing, noise, and load stability from the manufacturer datasheet.
Direkomendasikan
Power-Supply Feedback Monitoring
The LM224ADRG4 can monitor and condition feedback signals in industrial or communications power-conversion systems where multiple analog channels are useful. Its four internally compensated amplifiers allow separate functions such as error-amplifier support, output-voltage sensing, current-shunt amplification, and fault-signal conditioning. The 30 V maximum supply rating supports conventional high-voltage analog rails, although the actual circuit must respect the complete input, output, and absolute-maximum limits. Keep sensing paths short, use Kelvin routing where shunt resistance is low, and account for the 3 mV typical input offset when determining the smallest detectable supply error. The 1.2 MHz gain-bandwidth product is suitable for control-loop and monitoring paths whose bandwidth is far below the amplifier limit.
Direkomendasikan
Data Acquisition Front End
The LM224ADRG4 is useful in a low-speed data-acquisition front end when four channels must amplify or buffer inputs before conversion. Its 1.2 MHz gain-bandwidth product can support signal paths well below the conversion rate, and the 14-pin SOIC package reduces the component count compared with four separate amplifier packages. Common uses include buffer amplifiers for sensor outputs, differential-to-single-ended stages, and programmable-gain building blocks using passive networks. Evaluate source impedance and amplifier bias current for high-impedance sensors, and verify that the 3 mV typical offset fits the acquisition resolution. The -25°C to 85°C range covers many industrial environments, but enclosure heating can reduce the allowable board temperature margin.
Direkomendasikan
Control-System Signal Conditioning
The LM224ADRG4 fits control and monitoring boards that need several general-purpose analog channels at modest bandwidth. The device can condition command signals, scale sensor feedback, generate error signals, and buffer outputs within one package. Its 1.2 MHz gain-bandwidth product provides ample bandwidth for common industrial control loops, while internal frequency compensation simplifies the design of standard unity-gain voltage followers and closed-loop amplifiers. Check the output-load and slew-rate requirements for actuator interfaces, and account for the 3 mV typical input offset when determining control accuracy. Confirm that each analog signal remains within the manufacturer input common-mode range and that the 30 V maximum supply is never exceeded under fault conditions.
Direkomendasikan
Portable Measurement Module
The LM224ADRG4 can support a compact battery-powered measurement module when four low-bandwidth analog functions must be handled within a limited board area. It may provide input buffering, gain stages, active filtering, or output isolation for a sensor cluster in a portable instrument. The 1.2 MHz gain-bandwidth product allows useful bandwidth for many slow physical measurements, but battery designs must still evaluate supply current and the amplifier's quiescent consumption from the manufacturer data. The 3 mV typical input offset may require offset correction for high-resolution measurements. The 14-pin SOIC package is easy to route in conventional PCB designs, and the -25°C to 85°C range covers many mobile and field-service operating environments.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk LM224ADRG4 — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | LM224ADR | LM224DRG4 |
|---|---|---|---|
| Package | 14-SOIC (D) | 14-SOIC (D) | 14-SOIC (D) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Number of Amplifiers | 4 circuits | 4 circuits | 4 circuits |
| Gain-Bandwidth Product | 1.2 MHz | 1.2 MHz | 1.2 MHz |
| Maximum Supply Voltage | 30 V | 30 V | 30 V |
| Typical Input Offset Voltage | 3 mV | 3 mV | 3 mV |
| Frequency Compensation | Internally compensated | Internally compensated | Internally compensated |
| Operating Supply Voltage | ±16 V or 32 V | ±16 V or 32 V | ±16 V or 32 V |
| Orderable Configuration | LM224ADRG4 tape-and-reel code | LM224ADR shortened ordering code | Wider-temperature family ordering code |
Diferensiator Kunci
- Four general-purpose amplifiers in one package (vsLM224ADR)
- Identified industrial temperature coverage (vsLM224DRG4)
- General-purpose 1.2 MHz performance with 3 mV typical offset (vsLM324ADR2G)
Catatan Desain
Use the manufacturer pin-description table to route the four amplifier channels and the common power connections. Place the supply bypass capacitor immediately between the supply and ground pins, with a short ground return and minimal loop area. Although the LM224ADRG4 uses a conventional 14-pin SOIC, incorrect channel assignment or bypass placement can introduce instability or amplify switching noise. Keep sensitive input and feedback traces away from inductor, relay, and power-converter nodes.
Do not assume that every 14-pin quad op amp is interchangeable with the LM224ADRG4. Confirm channel pinout, input common-mode range, output swing, supply-current behavior, offset limits, and stability with the intended load. The published 3 mV typical input offset can create meaningful error in millivolt-level sensor circuits. Also verify that the -25°C to 85°C LM224ADRG4 temperature rating covers the hottest expected board temperature rather than only the nominal ambient specification.
The 1.2 MHz gain-bandwidth product makes the LM224ADRG4 suitable for many low-bandwidth closed-loop stages, but noise gain and feedback impedance still determine usable bandwidth. Avoid extremely high source or feedback impedances when accurate dc behavior is required, because bias current and offset effects become more significant. For sensor lines, use guarded routing and a nearby buffer, and test the completed amplifier with the expected cable capacitance and load rather than an ideal simulator load.
Informasi Konformitas
The product listing excerpts do not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. LM224ADRG4 is a general-purpose commercial amplifier rather than an automotive-qualified AEC-Q100 device.