MAX232CWE+T - Dual RS-232 Transceiver | Analog Devices
MPN: MAX232CWE+T ✓ AktifMAX232CWE+T Ringkasan
An RS-232 transceiver is an interface IC that converts logic-level signals into differential bipolar RS-232 levels and converts received bipolar signals back into CMOS-compatible logic. The MAX232CWE+T belongs to the line-driver and receiver hierarchy, providing the physical-layer functions required to connect a UART, microcontroller, or embedded controller to a serial port. It is particularly useful where the system cannot provide the positive and negative rails normally associated with RS-232 equipment.
Key features include two driver channels, two receiver channels, a single +5 V supply, and operation at 120 kbps. The charge-pump design permits RS-232 communication with only +5 V power, eliminating a dual-supply requirement and reducing board-level complexity. The wide SOIC package is a standard surface-mount option with adequate lead pitch for automated assembly and hand-soldering.
The device uses five external charge-pump capacitors to develop the bipolar voltage levels required for reliable transmission. Designers should place these capacitors close to the associated device pins and follow the connection arrangement in the manufacturer datasheet. Short, direct signal paths on the printed circuit board help limit ringing, reduce radiated emissions, and preserve the receiver's input threshold margin.
Typical uses include industrial serial consoles, instrumentation links, service equipment, barcode readers, point-of-sale terminals, and legacy peripheral connections. The MAX232CWE+T is appropriate where a +5 V system must communicate over an RS-232 cable with a host computer or controller while avoiding the older +12 V and -12 V supply architecture.
Choose this part when the required data rate is 120 kbps or lower and a 16-pin wide SOIC footprint is already on the PCB. Verify signal levels, cable length, grounding, and receiver thresholds at the system level, because RS-232 is a single-ended interface that depends on a common reference between connected equipment.
This page combines the manufacturer interface description with practical component comparison, pin-level implementation guidance, and design notes covering charge-pump capacitors, grounding, transmission limits, and second-source evaluation.
Alternatif penggantian untuk MAX232CWE+T — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian MAX232CWE+T (sama faktor bentuk dan footprint) — berbeda di dalam Product Type, Package, Maximum Data Rate, Number of Receivers, Number of Drivers.
SP232ACT-L/TR
✅ Drop-InKontak untuk harga
Lihat Datasheet →MAX232CWE+T Spesifikasi
| Product Type | RS-232 line-driver and receiver transceiver |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Duplex Mode | Full duplex |
| Maximum Data Rate | 120 kbps |
| Tegangan Pemuat | +5 V |
| Interface Standard | EIA/TIA-232E, V.28, and V.24 |
| Paket | 16-pin wide SOIC (WSOIC) |
| Tipe Mounting | Surface mount |
| External Charge-Pump Capacitors | 5 |
| Status RoHS | unknown |
| REACH Status | unknown |
| Lead-Free Status | unknown |
| Automotive Qualification | Not applicable |
| Shipping Configuration | Tape and reel |
Konfigurasi Pin MAX232CWE+T
| Pin produk 1 | R1OUT — Receiver 1 logic output |
| Pin produk 2 | R1IN — Receiver 1 RS-232 input |
| Pin produk 3 | R2OUT — Receiver 2 logic output |
| Pin produk 4 | R2IN — Receiver 2 RS-232 input |
| Pin produk 5 | T2IN — Driver 2 logic input |
| Pin produk 6 | T1IN — Driver 1 logic input |
| Pin produk 7 | V+ — Positive charge-pump supply node |
| Pin produk 8 | GND — Ground connection |
| Pin produk 9 | V- — Negative charge-pump output |
| Pin produk 10 | T1OUT — Driver 1 RS-232 output |
| Pin produk 11 | T2OUT — Driver 2 RS-232 output |
| Pin produk 12 | NC — Not connected |
| Pin produk 13 | NC — Not connected |
| Pin produk 14 | NC — Not connected |
| Pin produk 15 | GND — Ground connection |
| Pin produk 16 | V+ — Positive charge-pump supply node |
Aplikasi Umum
MAX232CWE+T cocok untuk 6 aplikasis: Industrial Serial Console, Laboratory Instrument Interface, Point-of-Sale Terminal Connection, Embedded Service and Configuration Port, Legacy Peripheral Data Link, Telemetry and Equipment Communication.
Industrial Serial Console
The MAX232CWE+T is well suited to an industrial console or service port that must connect a controller running at 5 V logic levels to a legacy RS-232 terminal. Its two drivers and two receivers support one full-duplex link, and the 120 kbps limit matches many administrative protocols, maintenance ports, and configuration interfaces. The integrated charge pump derives the required bipolar levels from one +5 V rail. Place the five charge-pump capacitors close to the device and route the cable-side traces away from sensitive analog and clock circuitry to limit radiated coupling.
Direkomendasikan
Laboratory Instrument Interface
Laboratory instruments and automated test equipment often retain RS-232 even when their internal controller operates with modern low-voltage logic. The MAX232CWE+T provides the required physical conversion while operating from +5 V, avoiding a separate +12 V and -12 V supply arrangement. Its 120 kbps rate suits command and measurement-data links that do not require continuous high-bandwidth transfer. Use a defined logic ground near the transceiver and verify the common-mode voltage range at the cable connector, because RS-232 is a single-ended interface sensitive to ground-potential differences.
Direkomendasikan
Point-of-Sale Terminal Connection
Point-of-sale terminals, receipt printers, barcode readers, and payment accessories frequently use RS-232 for short cable-based command links. The MAX232CWE+T fits a +5 V embedded controller that needs transmit and receive channels in one compact 16-pin SOIC package. A 120 kbps rate is appropriate for short transactions and configuration commands rather than high-volume imaging data. Confirm the cable length and receiver threshold margin, and keep the RS-232 trace pair separated from motor, relay, and switching-power-supply routing to avoid command errors.
Direkomendasikan
Embedded Service and Configuration Port
An embedded controller can use the MAX232CWE+T to expose a field-service configuration port that is accessible with a standard RS-232 cable. The device converts logic-level UART signals in both directions and eliminates the need for external bipolar supply rails. Its 120 kbps rate is sufficient for firmware menus, diagnostics, and short configuration transfers. Implement an enclosure ground reference or isolation strategy where the connected equipment can sit at a different earth potential, and use the datasheet's receiver threshold limits to define the acceptable common-mode range.
Direkomendasikan
Legacy Peripheral Data Link
The MAX232CWE+T connects modern +5 V logic to printers, programmers, scales, and other legacy peripherals that expose RS-232 ports. Because the device includes two transmitters and two receivers, one port can handle bidirectional command and response traffic while leaving the other direction available for status or flow-control signaling. The 120 kbps maximum rate suits legacy control protocols. Verify the peripheral's driver and receiver voltage levels, handshaking requirements, and pin assignment before finalizing the cable adapter and software protocol.
Direkomendasikan
Telemetry and Equipment Communication
MAX232CWE+T can serve as the local RS-232 interface in telemetry, remote-monitoring, and equipment-communication modules built around a low-voltage microcontroller or embedded processor. The single +5 V supply arrangement simplifies powering the interface in compact control boards, while the integrated charge pump supplies the bipolar levels needed by the RS-232 drivers. Use it for status reports and configuration traffic at or below 120 kbps. Shield long cable runs appropriately, provide a stable signal-ground reference, and apply the receiver threshold limits when designing a multi-drop or distributed installation.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk MAX232CWE+T — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | SP232ACT-L/TR |
|---|---|---|
| Brand | Analog Devices | MaxLinear |
| Package | 16-pin wide SOIC | 16-pin SOIC |
| Transceiver Configuration | 2 drivers and 2 receivers | 2 drivers and 2 receivers |
Diferensiator Kunci
- Single +5 V supply with integrated bipolar charge pump (vsSP232ACT-L/TR)
- Documented 120 kbps maximum data rate (vsSP232ACT-L/TR)
- Two transmitters and two receivers in one device (vsSP232ACT-L/TR)
Catatan Desain
Place the five external charge-pump capacitors adjacent to the pins shown in the manufacturer application circuit, and keep each capacitor's connection loop as short as practical. The switching charge-pump current circulates through these paths, so long traces can radiate noise into nearby receivers. Avoid routing RS-232 inputs and outputs directly beneath the charge-pump network, and provide a continuous ground reference beneath the device where board area permits.
Do not assume that every MAX232 ordering code is a board-level substitute. The C suffix denotes the wide SOIC package in this naming convention, while E denotes a narrow-body package with different lead dimensions. Confirm the manufacturer package drawing, pin numbering, and exposed or non-exposed pad arrangement before changing the bill of materials. Also verify the operating-temperature grade and supply requirements of the specific ordering code.
RS-232 is a single-ended standard, so the receiver's reference to the transmitter ground determines the available noise margin. Connect the interface ground to the equipment chassis or logic ground through the strategy defined for the finished product, and keep that connection away from high-current return paths. Long cables should use a defined shield ground and surge protection appropriate to the installation rather than relying on the transceiver alone for lightning or industrial transient protection.
Informasi Konformitas
No definitive RoHS, REACH, halogen-free, or conflict-minerals declaration was identified for this ordering code. Confirm compliance documentation for the exact lot and shipping configuration when required by a customer specification.