MAX3221IDBG4 - Single RS-232 Transceiver | Texas Instruments
MPN: MAX3221IDBG4 ✓ AktifMAX3221IDBG4 Ringkasan
An RS-232 transceiver is an interface IC that converts logic-level signals from a host, controller, or embedded processor into RS-232 voltage levels, while converting incoming RS-232 signals back into CMOS-compatible logic. This device belongs to the interface IC hierarchy, combining a line driver, line receiver, and dual charge-pump voltage-conversion circuitry in one package. It is designed to bridge modern digital electronics with legacy RS-232 equipment.
The MAX3221IDBG4 provides one driver and one receiver, making it appropriate for point-to-point serial links, industrial equipment, data-acquisition systems, service interfaces, and embedded control products. Its 3 V to 5.5 V operating range allows operation from both 3.3 V and 5 V systems. The 250 kbit/s data rate supports moderate-speed serial communication while the integrated charge pumps generate the bipolar voltage levels required by RS-232 without requiring a separate negative supply.
The ±15 kV ESD rating applies to the human-body model and is intended to improve protection when cables are connected to exposed communication ports. This protection does not eliminate the need for appropriate system-level grounding, shielding, or surge-protection design. The device also uses charge-pump circuitry, so power-supply bypass capacitors and careful layout around the flying-capacitor connections remain important for stable operation.
Typical uses include service-console interfaces, industrial control panels, instrumentation, point-of-sale equipment, and systems that retain an RS-232 port while using a modern microcontroller. Its single-channel architecture minimizes board area compared with multi-channel transceivers when only one serial port is required.
When selecting this interface, verify the connector's signal polarity, the host-side logic levels, the required data rate, and the grounding arrangement. Place the charge-pump capacitors and supply bypass capacitors close to their specified pins, and observe the recommended connector and cable-routing practices for exposed RS-232 ports. This page combines device specifications, sourcing guidance, compatible alternatives, and practical interface-design notes for engineers evaluating the MAX3221IDBG4.
Alternatif penggantian untuk MAX3221IDBG4 — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian MAX3221IDBG4 (sama faktor bentuk dan footprint) — berbeda di dalam Package, Product Type, Supply Voltage Range, Maximum Data Rate, Number of Drivers.
MAX3221IDB
✅ Drop-InKontak untuk harga
Lihat Datasheet →MAX3221MDBREP
✅ Drop-InKontak untuk harga
Lihat Datasheet →MAX3221CAE+
✅ Drop-InKontak untuk harga
Lihat Datasheet →MAX3221IDBG4 Spesifikasi
| Device Type | RS-232 line driver/receiver transceiver |
| Number of Drivers | 1 |
| Number of Receivers | 1 |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbit/s |
| Protocol | RS-232 |
| ESD Protection | ±15 kV human-body model |
| ESD Protected Pins | Serial-port connection pins, including GND |
| Compliance | TIA/EIA-232-F and ITU V.28 requirements |
| Voltage Conversion | Dual charge-pump circuit |
| Paket | 16-SSOP |
| Package Width | 5.30 mm |
| Package Body Width | 0.209 inch |
| Tipe Mounting | Surface mount |
| Lead-Free Status | Lead-free |
| Green Product | Yes |
| Antimony and Bromide | Free |
| Kategori | Integrated Circuits > Interface ICs > RS-232, RS-422, RS-485 Interface ICs |
MAX3221IDBG4 0.209 inch Diamant Konfigurasi Panduan
Konfigurasi pin untuk MAX3221IDBG4 (0.209 inch pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.
Tidak ada data diatribut pin yang tersedia untuk MAX3221IDBG4.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
MAX3221IDBG4 cocok untuk 6 aplikasis: Industrial Control Panels, Data-Acquisition Equipment, Point-of-Sale Terminals, Instrument Service Interfaces, Embedded Serial Service Ports, Remote Monitoring and Telemetry.
Industrial Control Panels
The MAX3221IDBG4 suits industrial control panels that retain an RS-232 service or configuration port while using a modern 3.3 V or 5 V controller. Its single driver and single receiver provide bidirectional signal conversion in a 16-SSOP package, while 250 kbit/s operation is sufficient for configuration consoles, parameter transfer, and supervisory commands. The ±15 kV human-body-model ESD protection on the serial connection pins adds useful defense for a cable-accessible port, although the enclosure, grounding, and cable routing still determine overall surge robustness. Use a low-noise bypass capacitor at the supply pins and place the charge-pump capacitors exactly as shown in the manufacturer layout to avoid converter noise or unstable startup.
Direkomendasikan
Data-Acquisition Equipment
For laboratory and industrial data-acquisition equipment, the MAX3221IDBG4 provides a compact interface between a controller and a legacy RS-232 instrument. The 3 V to 5.5 V supply range supports both 3.3 V embedded processors and 5 V control logic, while the 250 kbit/s limit accommodates many command and measurement-data links. The single-channel arrangement reduces footprint and power-system complexity when only one port is needed. Its integrated dual charge pump generates the required RS-232 levels, eliminating a separate negative rail. Place the bypass and charge-pump capacitors close to the device, route the interface ground with the signal return, and verify that the connected instrument uses compatible RS-232 voltage levels and signal polarity.
Direkomendasikan
Point-of-Sale Terminals
The MAX3221IDBG4 can provide a compact RS-232 connection between a point-of-sale terminal or peripheral and a legacy printer, scanner, or customer-display device. One driver and one receiver cover the required single-port conversion, and the 16-SSOP package preserves board area in compact equipment. Its 3 V to 5.5 V operating range allows use with common embedded system supplies, while the 250 kbit/s data rate is more than adequate for many peripheral-control protocols. The ±15 kV human-body-model rating is valuable for exposed service connectors. Design the connector-side ground as a low-impedance return path, use the manufacturer-specified capacitor values, and verify whether the peripheral requires hardware or software flow control.
Direkomendasikan
Instrument Service Interfaces
The MAX3221IDBG4 is appropriate for a service interface on test and measurement instruments where technicians connect a computer or service controller through RS-232. The device's one-driver, one-receiver configuration supports bidirectional command and response traffic, and 250 kbit/s operation supports common service-port baud rates. Its low-voltage supply range simplifies connection to 3.3 V and 5 V instrument control sections. Integrated charge-pump circuitry removes the need for a separate negative supply, while ±15 kV human-body-model ESD protection helps manage incidental cable-contact transients. Keep the RS-232 traces short and away from sensitive analog nodes, connect the interface ground correctly, and use the datasheet capacitor arrangement to preserve signal and power integrity.
Direkomendasikan
Embedded Serial Service Ports
The MAX3221IDBG4 allows a microcontroller-based product to retain a wired RS-232 service port for configuration, diagnostics, and firmware maintenance. Its 16-SSOP package and single-channel architecture are useful where board space is limited but one legacy serial interface is essential. The MAX3221IDBG4 accepts a 3 V to 5.5 V supply and supports communication at up to 250 kbit/s, matching many embedded debug and configuration protocols. Its dual charge-pump circuitry produces the bipolar RS-232 levels internally. Place the flying capacitors and supply bypass capacitor directly beside the associated pins, keep the charge-pump loop compact, and isolate the connector ground from noisy power-return paths where the system architecture requires separate signal and power grounds.
Direkomendasikan
Remote Monitoring and Telemetry
The MAX3221IDBG4 can be used in remote monitoring equipment that sends configuration commands or telemetry over a wired RS-232 link. Its 250 kbit/s data rate supports moderate-speed telemetry bursts, while the single driver and receiver reduce component count and board area compared with a multi-channel interface. The 3 V to 5.5 V supply range allows operation from either 3.3 V or 5 V telemetry controllers, and the internal charge pumps eliminate a separate negative supply. The ±15 kV human-body-model ESD rating on serial connection pins is especially relevant when the cable reaches beyond an enclosed enclosure. Use shielded cable where appropriate, connect signal ground consistently at the interface, and verify surge requirements beyond human-body-model ESD with an external protection network.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk MAX3221IDBG4 — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | MAX3221IDB | MAX3221MDBREP | MAX3221CAE |
|---|---|---|---|---|
| Package | 16-SSOP | 16-SSOP | 16-SSOP | 16-SSOP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Device Type | Single RS-232 transceiver | Single RS-232 transceiver | Single RS-232 transceiver | Single RS-232 transceiver |
| Number of Drivers | 1 | 1 | 1 | 1 |
| Number of Receivers | 1 | 1 | 1 | 1 |
| Supply Voltage Range | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbit/s | 250 kbit/s | 250 kbit/s | 250 kbit/s |
| ESD Protection | ±15 kV human-body model | ±15 kV human-body model | ±15 kV human-body model | ±15 kV human-body model |
| Charge-Pump Circuit | Dual charge-pump circuit | Dual charge-pump circuit | Dual charge-pump circuit | Dual charge-pump circuit |
Diferensiator Kunci
- Compact single-channel RS-232 conversion (vsMAX3221CAE)
- Direct same-family interface architecture (vsMAX3221IDB)
- Single-rail RS-232 level generation (vsMAX3221MDBREP)
Catatan Desain
Place the charge-pump capacitors and the supply bypass capacitor directly beside their associated MAX3221IDBG4 pins. Keep these loops compact, use the shortest practical ground return, and avoid routing the high-current charge-pump paths beneath sensitive analog or communication lines. The 3 V to 5.5 V operating range supports common system rails, but stable capacitor connections are essential for clean charge-pump operation and reliable RS-232 level generation.
Do not treat the ±15 kV human-body-model ESD rating as complete protection against every cable-borne surge. Connect the interface ground with the RS-232 signal return, use a suitable enclosure and cable strategy, and add external protection when the connector can encounter industrial surge or discharge conditions. Also verify whether the connected equipment requires hardware flow control or a particular RS-232 signal polarity.
Keep connector-side RS-232 traces separated from sensitive board areas and route them away from clocks, switching regulators, and high-current return paths. Use a continuous reference plane where practical, maintain return continuity beneath the interface, and terminate unused inputs according to the manufacturer recommendations. Before releasing a cross-reference design, compare the complete pin descriptions and physical drawings of the exact replacement ordering code.
Informasi Konformitas
The MAX3221IDBG4 listing identifies lead-free status and a green product without antimony and bromide. RoHS compliance is shown in the component comparison information; REACH, halogen-free status, and conflict-minerals status are not confirmed.