MAX3221IDBG4 - Single RS-232 Transceiver | Texas Instruments
MPN: MAX3221IDBG4 ✓ Hoạt độngMAX3221IDBG4 Tóm tắt
An RS-232 transceiver is an interface IC that converts logic-level signals from a host, controller, or embedded processor into RS-232 voltage levels, while converting incoming RS-232 signals back into CMOS-compatible logic. This device belongs to the interface IC hierarchy, combining a line driver, line receiver, and dual charge-pump voltage-conversion circuitry in one package. It is designed to bridge modern digital electronics with legacy RS-232 equipment.
The MAX3221IDBG4 provides one driver and one receiver, making it appropriate for point-to-point serial links, industrial equipment, data-acquisition systems, service interfaces, and embedded control products. Its 3 V to 5.5 V operating range allows operation from both 3.3 V and 5 V systems. The 250 kbit/s data rate supports moderate-speed serial communication while the integrated charge pumps generate the bipolar voltage levels required by RS-232 without requiring a separate negative supply.
The ±15 kV ESD rating applies to the human-body model and is intended to improve protection when cables are connected to exposed communication ports. This protection does not eliminate the need for appropriate system-level grounding, shielding, or surge-protection design. The device also uses charge-pump circuitry, so power-supply bypass capacitors and careful layout around the flying-capacitor connections remain important for stable operation.
Typical uses include service-console interfaces, industrial control panels, instrumentation, point-of-sale equipment, and systems that retain an RS-232 port while using a modern microcontroller. Its single-channel architecture minimizes board area compared with multi-channel transceivers when only one serial port is required.
When selecting this interface, verify the connector's signal polarity, the host-side logic levels, the required data rate, and the grounding arrangement. Place the charge-pump capacitors and supply bypass capacitors close to their specified pins, and observe the recommended connector and cable-routing practices for exposed RS-232 ports. This page combines device specifications, sourcing guidance, compatible alternatives, and practical interface-design notes for engineers evaluating the MAX3221IDBG4.
Bộ thay thế dễ dàng lắp đặt cho MAX3221IDBG4 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MAX3221IDBG4 (cùng hình factor và footprint) — khác nhau ở Package, Product Type, Supply Voltage Range, Maximum Data Rate, Number of Drivers.
MAX3221IDB
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX3221MDBREP
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX3221CAE+
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX3221IDBG4 Thông số kỹ thuật
| Device Type | RS-232 line driver/receiver transceiver |
| Number of Drivers | 1 |
| Number of Receivers | 1 |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbit/s |
| Protocol | RS-232 |
| ESD Protection | ±15 kV human-body model |
| ESD Protected Pins | Serial-port connection pins, including GND |
| Compliance | TIA/EIA-232-F and ITU V.28 requirements |
| Voltage Conversion | Dual charge-pump circuit |
| Hộp | 16-SSOP |
| Package Width | 5.30 mm |
| Package Body Width | 0.209 inch |
| Kiểu lắp đặt | Surface mount |
| Lead-Free Status | Lead-free |
| Green Product | Yes |
| Antimony and Bromide | Free |
| Danh mục | Integrated Circuits > Interface ICs > RS-232, RS-422, RS-485 Interface ICs |
Hướng dẫn cấu hình chân MAX3221IDBG4 0.209 inch
Cấu hình chân cho MAX3221IDBG4 (0.209 inch gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho MAX3221IDBG4.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MAX3221IDBG4 phù hợp cho 6 Áp dụngs: Industrial Control Panels, Data-Acquisition Equipment, Point-of-Sale Terminals, Instrument Service Interfaces, Embedded Serial Service Ports, Remote Monitoring and Telemetry.
Industrial Control Panels
The MAX3221IDBG4 suits industrial control panels that retain an RS-232 service or configuration port while using a modern 3.3 V or 5 V controller. Its single driver and single receiver provide bidirectional signal conversion in a 16-SSOP package, while 250 kbit/s operation is sufficient for configuration consoles, parameter transfer, and supervisory commands. The ±15 kV human-body-model ESD protection on the serial connection pins adds useful defense for a cable-accessible port, although the enclosure, grounding, and cable routing still determine overall surge robustness. Use a low-noise bypass capacitor at the supply pins and place the charge-pump capacitors exactly as shown in the manufacturer layout to avoid converter noise or unstable startup.
Được đề xuất
Data-Acquisition Equipment
For laboratory and industrial data-acquisition equipment, the MAX3221IDBG4 provides a compact interface between a controller and a legacy RS-232 instrument. The 3 V to 5.5 V supply range supports both 3.3 V embedded processors and 5 V control logic, while the 250 kbit/s limit accommodates many command and measurement-data links. The single-channel arrangement reduces footprint and power-system complexity when only one port is needed. Its integrated dual charge pump generates the required RS-232 levels, eliminating a separate negative rail. Place the bypass and charge-pump capacitors close to the device, route the interface ground with the signal return, and verify that the connected instrument uses compatible RS-232 voltage levels and signal polarity.
Được đề xuất
Point-of-Sale Terminals
The MAX3221IDBG4 can provide a compact RS-232 connection between a point-of-sale terminal or peripheral and a legacy printer, scanner, or customer-display device. One driver and one receiver cover the required single-port conversion, and the 16-SSOP package preserves board area in compact equipment. Its 3 V to 5.5 V operating range allows use with common embedded system supplies, while the 250 kbit/s data rate is more than adequate for many peripheral-control protocols. The ±15 kV human-body-model rating is valuable for exposed service connectors. Design the connector-side ground as a low-impedance return path, use the manufacturer-specified capacitor values, and verify whether the peripheral requires hardware or software flow control.
Được đề xuất
Instrument Service Interfaces
The MAX3221IDBG4 is appropriate for a service interface on test and measurement instruments where technicians connect a computer or service controller through RS-232. The device's one-driver, one-receiver configuration supports bidirectional command and response traffic, and 250 kbit/s operation supports common service-port baud rates. Its low-voltage supply range simplifies connection to 3.3 V and 5 V instrument control sections. Integrated charge-pump circuitry removes the need for a separate negative supply, while ±15 kV human-body-model ESD protection helps manage incidental cable-contact transients. Keep the RS-232 traces short and away from sensitive analog nodes, connect the interface ground correctly, and use the datasheet capacitor arrangement to preserve signal and power integrity.
Được đề xuất
Embedded Serial Service Ports
The MAX3221IDBG4 allows a microcontroller-based product to retain a wired RS-232 service port for configuration, diagnostics, and firmware maintenance. Its 16-SSOP package and single-channel architecture are useful where board space is limited but one legacy serial interface is essential. The MAX3221IDBG4 accepts a 3 V to 5.5 V supply and supports communication at up to 250 kbit/s, matching many embedded debug and configuration protocols. Its dual charge-pump circuitry produces the bipolar RS-232 levels internally. Place the flying capacitors and supply bypass capacitor directly beside the associated pins, keep the charge-pump loop compact, and isolate the connector ground from noisy power-return paths where the system architecture requires separate signal and power grounds.
Được đề xuất
Remote Monitoring and Telemetry
The MAX3221IDBG4 can be used in remote monitoring equipment that sends configuration commands or telemetry over a wired RS-232 link. Its 250 kbit/s data rate supports moderate-speed telemetry bursts, while the single driver and receiver reduce component count and board area compared with a multi-channel interface. The 3 V to 5.5 V supply range allows operation from either 3.3 V or 5 V telemetry controllers, and the internal charge pumps eliminate a separate negative supply. The ±15 kV human-body-model ESD rating on serial connection pins is especially relevant when the cable reaches beyond an enclosed enclosure. Use shielded cable where appropriate, connect signal ground consistently at the interface, and verify surge requirements beyond human-body-model ESD with an external protection network.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MAX3221IDBG4 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MAX3221IDB | MAX3221MDBREP | MAX3221CAE |
|---|---|---|---|---|
| Package | 16-SSOP | 16-SSOP | 16-SSOP | 16-SSOP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Device Type | Single RS-232 transceiver | Single RS-232 transceiver | Single RS-232 transceiver | Single RS-232 transceiver |
| Number of Drivers | 1 | 1 | 1 | 1 |
| Number of Receivers | 1 | 1 | 1 | 1 |
| Supply Voltage Range | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbit/s | 250 kbit/s | 250 kbit/s | 250 kbit/s |
| ESD Protection | ±15 kV human-body model | ±15 kV human-body model | ±15 kV human-body model | ±15 kV human-body model |
| Charge-Pump Circuit | Dual charge-pump circuit | Dual charge-pump circuit | Dual charge-pump circuit | Dual charge-pump circuit |
Bảo phân biệt quan trọng
- Compact single-channel RS-232 conversion (vsMAX3221CAE)
- Direct same-family interface architecture (vsMAX3221IDB)
- Single-rail RS-232 level generation (vsMAX3221MDBREP)
Ghi chú thiết kế
Place the charge-pump capacitors and the supply bypass capacitor directly beside their associated MAX3221IDBG4 pins. Keep these loops compact, use the shortest practical ground return, and avoid routing the high-current charge-pump paths beneath sensitive analog or communication lines. The 3 V to 5.5 V operating range supports common system rails, but stable capacitor connections are essential for clean charge-pump operation and reliable RS-232 level generation.
Do not treat the ±15 kV human-body-model ESD rating as complete protection against every cable-borne surge. Connect the interface ground with the RS-232 signal return, use a suitable enclosure and cable strategy, and add external protection when the connector can encounter industrial surge or discharge conditions. Also verify whether the connected equipment requires hardware flow control or a particular RS-232 signal polarity.
Keep connector-side RS-232 traces separated from sensitive board areas and route them away from clocks, switching regulators, and high-current return paths. Use a continuous reference plane where practical, maintain return continuity beneath the interface, and terminate unused inputs according to the manufacturer recommendations. Before releasing a cross-reference design, compare the complete pin descriptions and physical drawings of the exact replacement ordering code.
Thông tin tuân thủ
The MAX3221IDBG4 listing identifies lead-free status and a green product without antimony and bromide. RoHS compliance is shown in the component comparison information; REACH, halogen-free status, and conflict-minerals status are not confirmed.