MAX3232CDBG4 - 3V to 5.5V RS-232 Transceiver | TI
MPN: MAX3232CDBG4 ✓ AktifMAX3232CDBG4 Ringkasan
An RS-232 transceiver is an interface IC that converts logic-level signals from a microcontroller, DSP, or computer into RS-232-compliant line levels and converts received RS-232 signals back into logic levels. The MAX3232 belongs to the line-driver and line-receiver hierarchy within interface ICs, bridging modern CMOS logic and the voltage levels used by legacy serial ports, industrial controllers, and point-of-sale equipment.
Principal features include a 1 Mbps maximum data rate, a 3.0 V to 5.5 V supply range, two transmit channels, two receive channels, and low-power operation. The commercial-temperature grade covers 0 °C to 70 °C. Its SSOP-16 package is suitable for compact PCB layouts where a larger SOIC footprint would be undesirable, and the lead-free gull-wing package is compatible with standard surface-mount assembly.
The transceiver generates the positive and negative RS-232 voltages from the single supply using an internal charge-pump circuit. Four 0.1 µF capacitors are required for that circuit, while the MAX3232 family operates without an external 5 V supply. Because RS-232 is a single-ended, unbalanced interface, the transceiver provides level translation but not galvanic isolation or long-distance noise immunity comparable with differential interfaces such as RS-485.
Typical applications include industrial control panels, serial adapters, automated test equipment, point-of-sale terminals, security systems, and embedded instrumentation. The 1 Mbps capability supports both legacy printer and mouse protocols as well as higher-rate data links when the connected equipment supports the corresponding protocol and cable characteristics.
When laying out the board, place the four charge-pump capacitors close to the device and keep the RS-232 traces away from sensitive analog or high-speed digital nets. Confirm the ground reference and cable shielding, and verify the logic levels against the host interface before energizing the board.
This page organizes the electrical ratings, package details, equivalent transceiver options, and application guidance needed to evaluate the MAX3232CDBG4 for a new RS-232 interface design.
Alternatif penggantian untuk MAX3232CDBG4 — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian MAX3232CDBG4 (sama faktor bentuk dan footprint) — berbeda di dalam Supply Voltage Range, ESD Protection, External Capacitors, Function, Package.
MAX3232EIPWG4
✅ Drop-InKontak untuk harga
Lihat Datasheet →MAX3232CDE4
✅ Drop-InKontak untuk harga
Lihat Datasheet →TRS3232EIRGT
✅ Drop-InKontak untuk harga
Lihat Datasheet →MAX3232CDBG4 Spesifikasi
| Product Type | RS-232 line driver/receiver transceiver |
| Supply Voltage Range | 3.0 V to 5.5 V |
| Maximum Data Rate | 1 Mbps |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Duplex Mode | Full duplex |
| ESD Protection | ±15 kV |
| Charge-Pump Capacitors Required | 4 external 0.1 µF capacitors |
| Rentang Suhu Kerja | 0 °C to 70 °C |
| Temperature Grade | Commercial |
| Package Type | SSOP-16 |
| Terminal Count | 16 |
| Terminal Form | Gull wing |
| Tipe Mounting | Surface mount |
| Logic Technology | CMOS |
| Lead-Free Status | Lead free |
| RoHS Compliance | Compliant |
| Product Lifecycle Status | Active |
MAX3232CDBG4 ssop-16 Diamant Konfigurasi Panduan
Konfigurasi pin untuk MAX3232CDBG4 (ssop-16 pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.
Tidak ada data diatribut pin yang tersedia untuk MAX3232CDBG4.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
MAX3232CDBG4 cocok untuk 6 aplikasis: Industrial Serial Control Panels, Point-of-Sale Terminals, Automated Test and Measurement Equipment, Embedded Security and Access Systems, Serial Adapters and Dongles, Printer and Legacy Peripheral Interfaces.
Industrial Serial Control Panels
The MAX3232CDBG4 suits controller boards that must communicate with legacy RS-232 panels, scales, or service ports. Its two drivers and two receivers support full-duplex exchange, while the 3.0 V to 5.5 V operating range allows connection to either a 3.3 V microcontroller rail or a 5 V controller. The 1 Mbps capability provides margin for common serial protocols. Designers should keep the four charge-pump capacitors close to the IC and route the RS-232 cable interface away from sensitive analog sections.
Direkomendasikan
Point-of-Sale Terminals
POS peripherals often retain RS-232 connectors even when the main processor uses modern low-voltage logic. The MAX3232CDBG4 provides the required level translation through two transmit and two receive channels, operates from a single 3.0 V to 5.5 V supply, and eliminates the need for a separate RS-232 voltage source. The 16-pin SSOP package conserves board area in compact terminals. Firmware must match the UART baud rate and framing of the connected peripheral.
Direkomendasikan
Automated Test and Measurement Equipment
Instrument controllers often need a short-distance serial link to a front panel, printer, or legacy test fixture. The MAX3232CDBG4 supports rates up to 1 Mbps, allowing designers to select faster serial modes when the peripheral supports them. Full-duplex operation permits simultaneous command transmission and response reception, while the commercial 0 °C to 70 °C range suits room-temperature test stations. Shielded cables and a common ground reference remain important for reliable industrial use.
Direkomendasikan
Embedded Security and Access Systems
Access-control readers, intercoms, and camera-control boards can use the MAX3232CDBG4 to connect a CMOS controller to an RS-232 configuration port or downstream accessory. Its single-supply operation simplifies power design, and the two-channel arrangement allows one link for configuration and another for status reporting. The 16-pin SSOP footprint supports compact boards, while ±15 kV ESD protection strengthens the interface against electrostatic discharge encountered during installation or servicing.
Direkomendasikan
Serial Adapters and Dongles
Compact serial adapters benefit from the MAX3232CDBG4 because it combines a 16-pin SSOP package, dual drivers, dual receivers, and single-supply operation in one component. The device supports both 3.3 V and 5 V host logic while presenting RS-232 levels to the attached peripheral. Designers should provide the datasheet-specified bypass capacitors, protect the connector from ESD, and verify that the cable length and baud rate suit the intended RS-232 application.
Direkomendasikan
Printer and Legacy Peripheral Interfaces
The MAX3232CDBG4 remains appropriate for printers, scales, and legacy peripherals that use RS-232 rather than USB. Its two transmitters and receivers can support full-duplex links, and the 1 Mbps maximum rate covers the performance requirements of many printer and instrument protocols. Because the device does not translate protocol formats, the connected UART must use the same baud rate, data width, parity, and stop-bit configuration as the peripheral.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk MAX3232CDBG4 — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | MAX3232E | MAX3232CDE4 | TRS3232E |
|---|---|---|---|---|
| Package | SSOP-16 | SSOP-16 | SSOP-16 | SSOP-16 |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Supply Voltage Range | 3.0 V to 5.5 V | 3.0 V to 5.5 V | 3.0 V to 5.5 V | 3.0 V to 5.5 V |
| Maximum Data Rate | 1 Mbps | 1 Mbps | 1 Mbps | 1 Mbps |
| Drivers and Receivers | 2 drivers, 2 receivers | 2 drivers, 2 receivers | 2 drivers, 2 receivers | 2 drivers, 2 receivers |
| Duplex Mode | Full duplex | Full duplex | Full duplex | Full duplex |
| External Charge-Pump Capacitors | 4 × 0.1 µF | 4 × 0.1 µF | 4 × 0.1 µF | 4 × 0.1 µF |
| New-Design Recommendation | Existing MAX3232C option | Recommended by the manufacturer comparison guidance | Family ordering variant | Alternative series comparison |
Diferensiator Kunci
- Manufacturer-recommended direct upgrade path (vsMAX3232E)
- Single-supply RS-232 operation in a compact footprint (vsMAX3232CDE4)
- Integrated ESD protection for external cabling (vsTRS3232E)
Catatan Desain
Place the four 0.1 µF charge-pump capacitors directly across their designated IC pins, with short traces and a solid ground connection. Keep the input and output bypass capacitors close to the supply and driver pins as well. Excessively long capacitor loops can allow switching transients from the charge pump to couple into the receiver path or reduce the guaranteed RS-232 output level.
Route RS-232 connector traces away from sensitive analog inputs, crystal circuits, and high-speed clock nets. Connect the cable shield to chassis or shield ground according to the equipment's grounding strategy, and provide a direct signal-ground return to the transceiver. Avoid routing RS-232 traces beneath the charge-pump capacitor network, where periodic current pulses can increase radiated noise.
Do not treat the 3.0 V to 5.5 V supply rating as permission to exceed 5.5 V. Confirm the logic-high thresholds of the connected UART, use the specified capacitor values, and observe the datasheet's no-connect and unused-driver guidance. When substituting another family member, verify the exact ordering suffix, package drawing, pin mapping, temperature grade, and ESD rating rather than matching only the MAX3232 family name.
Informasi Konformitas
The device is identified as a lead-free SSOP part. RoHS compliance is shown in the indexed component comparison. REACH, halogen-free, and conflict-minerals statuses were not established for this ordering code.