MAX3232CDBG4 - 3V to 5.5V RS-232 Transceiver | TI
MPN: MAX3232CDBG4 ✓ NakahandaMAX3232CDBG4 Ulas
An RS-232 transceiver is an interface IC that converts logic-level signals from a microcontroller, DSP, or computer into RS-232-compliant line levels and converts received RS-232 signals back into logic levels. The MAX3232 belongs to the line-driver and line-receiver hierarchy within interface ICs, bridging modern CMOS logic and the voltage levels used by legacy serial ports, industrial controllers, and point-of-sale equipment.
Principal features include a 1 Mbps maximum data rate, a 3.0 V to 5.5 V supply range, two transmit channels, two receive channels, and low-power operation. The commercial-temperature grade covers 0 °C to 70 °C. Its SSOP-16 package is suitable for compact PCB layouts where a larger SOIC footprint would be undesirable, and the lead-free gull-wing package is compatible with standard surface-mount assembly.
The transceiver generates the positive and negative RS-232 voltages from the single supply using an internal charge-pump circuit. Four 0.1 µF capacitors are required for that circuit, while the MAX3232 family operates without an external 5 V supply. Because RS-232 is a single-ended, unbalanced interface, the transceiver provides level translation but not galvanic isolation or long-distance noise immunity comparable with differential interfaces such as RS-485.
Typical applications include industrial control panels, serial adapters, automated test equipment, point-of-sale terminals, security systems, and embedded instrumentation. The 1 Mbps capability supports both legacy printer and mouse protocols as well as higher-rate data links when the connected equipment supports the corresponding protocol and cable characteristics.
When laying out the board, place the four charge-pump capacitors close to the device and keep the RS-232 traces away from sensitive analog or high-speed digital nets. Confirm the ground reference and cable shielding, and verify the logic levels against the host interface before energizing the board.
This page organizes the electrical ratings, package details, equivalent transceiver options, and application guidance needed to evaluate the MAX3232CDBG4 for a new RS-232 interface design.
Mga alternatibo na pwedeng ilagay na MAX3232CDBG4 — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok MAX3232CDBG4 (parehas na form factor at footprint) — pagkakaiba sa Supply Voltage Range, ESD Protection, External Capacitors, Function, Package.
MAX3232EIPWG4
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →MAX3232CDE4
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →TRS3232EIRGT
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →MAX3232CDBG4 Mga Spesipikasyon
| Product Type | RS-232 line driver/receiver transceiver |
| Supply Voltage Range | 3.0 V to 5.5 V |
| Maximum Data Rate | 1 Mbps |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Duplex Mode | Full duplex |
| ESD Protection | ±15 kV |
| Charge-Pump Capacitors Required | 4 external 0.1 µF capacitors |
| Hanay ng Temperature na Operasyon | 0 °C to 70 °C |
| Temperature Grade | Commercial |
| Package Type | SSOP-16 |
| Terminal Count | 16 |
| Terminal Form | Gull wing |
| Uri ng Pagpapasok | Surface mount |
| Logic Technology | CMOS |
| Lead-Free Status | Lead free |
| RoHS Compliance | Compliant |
| Product Lifecycle Status | Active |
Gabay sa Pin Configuration ng MAX3232CDBG4 ssop-16
Pin configuration para sa MAX3232CDBG4 (ssop-16 package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.
Wala ng detalyadong pinout data na magagamit para sa MAX3232CDBG4.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
MAX3232CDBG4 ay nararapat para sa 6 aplikasyons: Industrial Serial Control Panels, Point-of-Sale Terminals, Automated Test and Measurement Equipment, Embedded Security and Access Systems, Serial Adapters and Dongles, Printer and Legacy Peripheral Interfaces.
Industrial Serial Control Panels
The MAX3232CDBG4 suits controller boards that must communicate with legacy RS-232 panels, scales, or service ports. Its two drivers and two receivers support full-duplex exchange, while the 3.0 V to 5.5 V operating range allows connection to either a 3.3 V microcontroller rail or a 5 V controller. The 1 Mbps capability provides margin for common serial protocols. Designers should keep the four charge-pump capacitors close to the IC and route the RS-232 cable interface away from sensitive analog sections.
Inirekomenda
Point-of-Sale Terminals
POS peripherals often retain RS-232 connectors even when the main processor uses modern low-voltage logic. The MAX3232CDBG4 provides the required level translation through two transmit and two receive channels, operates from a single 3.0 V to 5.5 V supply, and eliminates the need for a separate RS-232 voltage source. The 16-pin SSOP package conserves board area in compact terminals. Firmware must match the UART baud rate and framing of the connected peripheral.
Inirekomenda
Automated Test and Measurement Equipment
Instrument controllers often need a short-distance serial link to a front panel, printer, or legacy test fixture. The MAX3232CDBG4 supports rates up to 1 Mbps, allowing designers to select faster serial modes when the peripheral supports them. Full-duplex operation permits simultaneous command transmission and response reception, while the commercial 0 °C to 70 °C range suits room-temperature test stations. Shielded cables and a common ground reference remain important for reliable industrial use.
Inirekomenda
Embedded Security and Access Systems
Access-control readers, intercoms, and camera-control boards can use the MAX3232CDBG4 to connect a CMOS controller to an RS-232 configuration port or downstream accessory. Its single-supply operation simplifies power design, and the two-channel arrangement allows one link for configuration and another for status reporting. The 16-pin SSOP footprint supports compact boards, while ±15 kV ESD protection strengthens the interface against electrostatic discharge encountered during installation or servicing.
Inirekomenda
Serial Adapters and Dongles
Compact serial adapters benefit from the MAX3232CDBG4 because it combines a 16-pin SSOP package, dual drivers, dual receivers, and single-supply operation in one component. The device supports both 3.3 V and 5 V host logic while presenting RS-232 levels to the attached peripheral. Designers should provide the datasheet-specified bypass capacitors, protect the connector from ESD, and verify that the cable length and baud rate suit the intended RS-232 application.
Inirekomenda
Printer and Legacy Peripheral Interfaces
The MAX3232CDBG4 remains appropriate for printers, scales, and legacy peripherals that use RS-232 rather than USB. Its two transmitters and receivers can support full-duplex links, and the 1 Mbps maximum rate covers the performance requirements of many printer and instrument protocols. Because the device does not translate protocol formats, the connected UART must use the same baud rate, data width, parity, and stop-bit configuration as the peripheral.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for MAX3232CDBG4 — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | MAX3232E | MAX3232CDE4 | TRS3232E |
|---|---|---|---|---|
| Package | SSOP-16 | SSOP-16 | SSOP-16 | SSOP-16 |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Supply Voltage Range | 3.0 V to 5.5 V | 3.0 V to 5.5 V | 3.0 V to 5.5 V | 3.0 V to 5.5 V |
| Maximum Data Rate | 1 Mbps | 1 Mbps | 1 Mbps | 1 Mbps |
| Drivers and Receivers | 2 drivers, 2 receivers | 2 drivers, 2 receivers | 2 drivers, 2 receivers | 2 drivers, 2 receivers |
| Duplex Mode | Full duplex | Full duplex | Full duplex | Full duplex |
| External Charge-Pump Capacitors | 4 × 0.1 µF | 4 × 0.1 µF | 4 × 0.1 µF | 4 × 0.1 µF |
| New-Design Recommendation | Existing MAX3232C option | Recommended by the manufacturer comparison guidance | Family ordering variant | Alternative series comparison |
Pangunahing mga Pagkakaiba
- Manufacturer-recommended direct upgrade path (kumpara saMAX3232E)
- Single-supply RS-232 operation in a compact footprint (kumpara saMAX3232CDE4)
- Integrated ESD protection for external cabling (kumpara saTRS3232E)
Talaan ng Disenyo
Place the four 0.1 µF charge-pump capacitors directly across their designated IC pins, with short traces and a solid ground connection. Keep the input and output bypass capacitors close to the supply and driver pins as well. Excessively long capacitor loops can allow switching transients from the charge pump to couple into the receiver path or reduce the guaranteed RS-232 output level.
Route RS-232 connector traces away from sensitive analog inputs, crystal circuits, and high-speed clock nets. Connect the cable shield to chassis or shield ground according to the equipment's grounding strategy, and provide a direct signal-ground return to the transceiver. Avoid routing RS-232 traces beneath the charge-pump capacitor network, where periodic current pulses can increase radiated noise.
Do not treat the 3.0 V to 5.5 V supply rating as permission to exceed 5.5 V. Confirm the logic-high thresholds of the connected UART, use the specified capacitor values, and observe the datasheet's no-connect and unused-driver guidance. When substituting another family member, verify the exact ordering suffix, package drawing, pin mapping, temperature grade, and ESD rating rather than matching only the MAX3232 family name.
Impormasyon ng Pagsunod sa Kautusan
The device is identified as a lead-free SSOP part. RoHS compliance is shown in the indexed component comparison. REACH, halogen-free, and conflict-minerals statuses were not established for this ordering code.