MAX3232CWE-TG068 - 3V-5.5V RS-232 Transceiver | Maxim
MPN: MAX3232CWE-TG068 ✓ AktifMAX3232CWE-TG068 Ringkasan
An RS-232 transceiver is an interface IC within the broader hierarchy of transceiver IC, interface IC, and semiconductor. True RS-232 implementations include the voltage levels, slew behavior, and driver-receiver arrangement required by the RS-232 standard. The MAX3232 family is designed for equipment that requires bidirectional serial communication without the higher supply voltage traditionally associated with older RS-232 implementations.
The MAX3232CWE-TG068 operates from 3.0 V to 5.5 V and supports communication rates up to 1 Mbps. Its low-power design is suitable for portable, industrial-control, instrumentation, and embedded equipment where supply current and board area matter. The manufacturer datasheet describes a charge-pump-assisted true RS-232 architecture and specifies the use of four 0.1 uF capacitors, allowing the device to generate the required bipolar voltage levels from a single low-voltage supply.
The CWE package is a 16-pin wide SOIC intended for surface-mount assembly. This package provides more spacing between pins than a narrow SOIC, which can simplify routing and hand-soldering in equipment assembled with mixed analog and digital circuitry. Operating and electrical details such as the complete pin assignment, temperature range, receiver thresholds, driver slew rate, and exact capacitor tolerances must be confirmed in the manufacturer datasheet before releasing a production design.
Typical applications include RS-232 ports in industrial controllers, laboratory instruments, barcode and data-acquisition equipment, service interfaces, and embedded systems that communicate with legacy peripherals. The 1 Mbps capability supports data links faster than conventional low-speed serial ports, while the 3.0 V to 5.5 V supply range permits operation from common embedded and logic rails.
A critical implementation detail is capacitor placement: route the four 0.1 uF charge-pump capacitors with short, direct traces and maintain the ground return close to the device. Keep RS-232 driver outputs away from sensitive receiver inputs, use the package's defined supply and ground pins, and verify external connector protection according to the voltage tolerance and grounding requirements of the finished equipment.
This product page consolidates the verified electrical envelope, package information, sourcing status, and engineering guidance for the MAX3232CWE-TG068. It also distinguishes verified same-footprint alternatives from narrower-package options and highlights the package and capacitance details that most directly affect PCB implementation.
Alternatif penggantian untuk MAX3232CWE-TG068 — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian MAX3232CWE-TG068 (sama faktor bentuk dan footprint) — berbeda di dalam Package, Product Type, Supply Voltage Range.
MAX3232CWE+
✅ Drop-InKontak untuk harga
Lihat Datasheet →MAX3232ECDW
✅ Drop-InKontak untuk harga
Lihat Datasheet →MAX328CWE
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
MAX3232CWE-TG068 Spesifikasi
| Product Type | RS-232 transceiver interface IC |
| Supply Voltage Range | 3.0 V to 5.5 V |
| Maximum Data Rate | 1 Mbps |
| RS-232 Transceiver Count | 2 drivers and 2 receivers |
| Charge-Pump Capacitor Requirement | 4 x 0.1 uF |
| Paket | 16-pin wide SOIC |
| Tipe Mounting | Surface mount |
| Transceiver Type | True RS-232 transceiver |
MAX3232CWE-TG068 16-pin wide soic Diamant Konfigurasi Panduan
Konfigurasi pin untuk MAX3232CWE-TG068 (16-pin wide soic pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.
Tidak ada data diatribut pin yang tersedia untuk MAX3232CWE-TG068.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
MAX3232CWE-TG068 cocok untuk 6 aplikasis: Industrial Controller RS-232 Port, Test and Measurement Instrument, Data-Acquisition Equipment, Embedded Service Interface, Portable Diagnostic Device, Barcode and Labeling Equipment.
Industrial Controller RS-232 Port
The MAX3232CWE-TG068 fits an industrial controller that must communicate with legacy RS-232 equipment from a 3.0 V to 5.5 V control system. Its true RS-232 interface supports data rates up to 1 Mbps, allowing the controller to serve as a maintenance, configuration, or supervisory link without requiring a separate high-voltage interface supply. The dual-driver and dual-receiver arrangement provides two RS-232 channels in one 16-pin wide SOIC. Four 0.1 uF charge-pump capacitors should be placed close to the device according to the manufacturer datasheet. A production design should also include defined logic-side grounding, connector-level protection, and verified common-mode behavior for the attached equipment.
Direkomendasikan
Test and Measurement Instrument
The MAX3232CWE-TG068 is useful in laboratory instruments that expose a PC-compatible RS-232 configuration port for calibration, logging, or instrument control. Its 3.0 V to 5.5 V supply range integrates easily with modern embedded control systems, while the 1 Mbps maximum data rate supports faster command and measurement-data transfers than conventional low-speed serial links. The wide SOIC package offers adequate lead spacing for mixed-signal boards. Place the four required 0.1 uF charge-pump capacitors close to their associated pins, and route the cable-side outputs away from sensitive analog sections. Verify logic levels, grounding, and ESD protection at the external connector.
Direkomendasikan
Data-Acquisition Equipment
The MAX3232CWE-TG068 can provide a compact command and status connection between a data-acquisition controller and an external computer or service terminal. Its low 3.0 V to 5.5 V operating range reduces the need for a separate RS-232 supply rail, while the capability for rates up to 1 Mbps accommodates burst-oriented status and configuration traffic. The two transmitters and two receivers allow more than one RS-232 node on the board, subject to the individual line and protocol requirements. Use the manufacturer charge-pump capacitor values and placement exactly, provide local supply decoupling, and add appropriate protection at any user-accessible connector. A logic-level cross-reference should be included in the schematic to simplify future board revisions.
Direkomendasikan
Embedded Service Interface
The MAX3232CWE-TG068 is appropriate for embedded products that require a service or configuration port using an RS-232 connector. Its 3.0 V minimum supply allows operation from common embedded rails, and its up-to-1-Mbps capability provides useful margin for firmware download logs, configuration exchanges, and diagnostic traffic. The wide SOIC package can simplify assembly where mixed component pitches are used. Maintain short charge-pump capacitor connections, avoid sharing sensitive signal returns with charge-pump currents, and define connector behavior when the port is disconnected or exposed to an external cable. For production equipment, incorporate a documented logic-level interface so that a future equivalent can be evaluated without changing the surrounding processor hardware.
Direkomendasikan
Portable Diagnostic Device
The MAX3232CWE-TG068 can support a portable diagnostic device that connects to a host computer through an RS-232 service cable. The 3.0 V to 5.5 V operating range is compatible with battery-derived and portable-system rails, and the low-power MAX3232 family avoids requiring a dedicated RS-232 voltage source. Its 1 Mbps capability is more than adequate for diagnostic commands and event logs while leaving margin for firmware update traffic. Validate the complete current draw for the intended operating mode and use the manufacturer's four 0.1 uF capacitor arrangement. Because an external cable introduces ESD and ground-transient risks, place protection at the connector boundary and verify the final system against its applicable interface requirements.
Direkomendasikan
Barcode and Labeling Equipment
The MAX3232CWE-TG068 suits barcode scanners, label printers, and production-floor equipment that use an RS-232 host connection. The 3.0 V to 5.5 V supply range simplifies integration with embedded controllers, and the 1 Mbps capability provides ample bandwidth for scan data, configuration commands, and status reporting. The 16-pin wide SOIC package supports mixed assembly methods and provides practical pin spacing compared with a narrow-SOIC version. Follow the manufacturer datasheet for the four 0.1 uF charge-pump capacitors and their placement. Keep the protected cable interface separated from sensitive logic, use a low-impedance ground path, and verify connector protection for the industrial environment in which the barcode equipment will operate.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk MAX3232CWE-TG068 — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | MAX3232CWE+ | MAX3232ECDW | MAX328CWE |
|---|---|---|---|---|
| Brand | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated |
| Package | SOIC-16 (Wide) | SOIC-16 (Wide) | SOIC-16 (Wide) | SOIC-16 (Wide) |
| Interface Standard | True RS-232 | True RS-232 | True RS-232 | RS-232 |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount |
Diferensiator Kunci
- Exact 3.0 V to 5.5 V low-voltage RS-232 operation (vsMAX328CWE)
- Close family-level functional match (vsMAX3232CWE+)
- Wide-body package aligns with the target footprint (vsMAX3232CSE+)
Catatan Desain
Place the four required 0.1 uF charge-pump capacitors directly beside their associated IC pins. Keep each capacitor connection short and symmetrical, and provide a nearby supply bypass capacitor on the device power pin. Avoid routing the charge-pump current path through areas carrying receiver inputs or low-level analog signals. The manufacturer datasheet pin table should be used to assign each capacitor because different MAX3232 package order codes must not be treated as interchangeable by name alone.
Do not substitute a narrow-SOIC MAX3232 variant for this wide-body CWE footprint without redesigning the PCB pads. MAX3232CSE+ and MAX3232EESE+T are identified as narrow-SOIC versions, so their lead spacing differs even though the family functions are related. Verify the package drawing, pin numbering, and exposed lead geometry before considering any ordering-code change. For an assembled PCB, use the manufacturer CWE drawing as the dimensional authority.
Separate the cable-side RS-232 nets from sensitive logic and analog traces. Keep driver outputs away from receiver inputs, especially on bidirectional RS-232 links where both directions share a connector. Route both transmit and receive pairs with consistent return paths, and evaluate the completed board for ground bounce when a connected device changes its ground reference. A connector-side protection network should be selected using the finished equipment's cable length and interface exposure rather than a generic component value.
Budget the MAX3232 supply current together with the load presented by the connected logic circuitry and external interface protection. The 3.0 V to 5.5 V operating range simplifies rail selection but does not remove the need for accurate source impedance and local decoupling. Confirm the low-power operating mode required by the application against the manufacturer datasheet. If the board sleeps between transactions, verify whether the remote RS-232 connection remains active and how that condition affects total system power.
Informasi Konformitas
The MAX3232 family is listed as production by Analog Devices. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations for the exact MAX3232CWE-TG068 configuration require confirmation from the manufacturer or its current compliance documentation.