MAX350CPN+ - Dual 4:1 Multiplexer, 100 ohm | Analog Devices
MPN: MAX350CPN+ ✓ AktifMAX350CPN+ Ringkasan
An analog multiplexer is an interface IC that connects one shared signal path to multiple inputs or one input to multiple outputs. The MAX350 belongs to the broader switch and multiplexer hierarchy, where low on-resistance, matched switch characteristics, and serial control are important for preserving signal integrity in test, measurement, and communication systems.
The MAX350 family provides on-resistance matched between switches to 16 ohm maximum and flat to 10 ohm maximum over the specified signal range. Its 100 ohm maximum on-resistance suits low-frequency analog routing, while serial control reduces the number of control inputs required on a constrained board. The dual 4:1 organization allows two multiplexers to operate as independent routing pairs.
The device supports continuous operation from dual supplies of ±2.7 V to ±8 V. It also supports a single-supply operating mode, although the complete single-supply limits must be confirmed in the manufacturer datasheet before final rail planning. Bidirectional conduction means the selected signal may travel into or out of the common terminal without changing the switch architecture.
Typical uses include automated test equipment, data-acquisition systems, instrumentation, signal routing, and communication equipment. In each case, the serial interface reduces control-line count while the matched low on-resistance helps minimize channel-dependent attenuation. The 18-pin DIP package is appropriate for through-hole prototype, legacy, and industrial assembly where surface-mount packaging is not required.
When laying out a board, keep common and switched traces short, provide a solid ground reference, and route control signals away from sensitive analog paths. Confirm supply sequencing, logic-level thresholds, signal-range limits, and exposed-pin assignments against the manufacturer datasheet before manufacturing.
This page combines manufacturer specifications, verified sourcing information, drop-in replacement analysis, application guidance, and design considerations to support component selection and PCB implementation.
Alternatif penggantian untuk MAX350CPN+ — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
MAX350CPN
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
MAX350CPN+ Spesifikasi
| Number of Circuits | 2 circuits |
| Multiplexer Configuration | Dual 4:1 |
| Number of Channels | 8 channels |
| Maximum On-Resistance | 100 ohm |
| On-Resistance Matching Between Switches | 16 ohm maximum |
| On-Resistance Flatness | 10 ohm maximum |
| Signal Conduction Direction | Bidirectional |
| Dual-Supply Operating Range | +/-2.7 V to +/-8 V |
| Control Interface | Serial |
| Package Type | 18-pin plastic DIP |
| Package Pin Count | 18 pins |
| Tipe Mounting | Through-hole |
MAX350CPN+ 18 pins Diamant Konfigurasi Panduan
Konfigurasi pin untuk MAX350CPN+ (18 pins pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.
Tidak ada data diatribut pin yang tersedia untuk MAX350CPN+.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
MAX350CPN+ cocok untuk 6 aplikasis: Automated Test Equipment, Data Acquisition Systems, Precision Signal Conditioning, Communication Interface Routing, Laboratory Instrumentation, Legacy Through-Hole Control Boards.
Automated Test Equipment
The MAX350CPN+ fits automated test systems that must route one analog measurement path among several sources or destinations. Two independent 4:1 circuits provide eight switched channels, while serial control reduces the number of parallel control lines required from the test controller. Bidirectional conduction allows the same routing fabric to support different signal directions. Its maximum on-resistance of 100 ohm and switch matching to 16 ohm maximum help control channel-dependent errors, although the selected node may require buffering when driving a high-impedance instrument. The 18-pin through-hole package also remains practical for legacy test fixtures, laboratory systems, and industrial controller boards built with plated-through-hole assembly.
Direkomendasikan
Data Acquisition Systems
The MAX350CPN+ can multiplex several low-frequency analog inputs into shared acquisition circuitry in a data-acquisition system. Its two 4:1 sections allow eight switched inputs to be organized as independent routing groups, and the serial interface simplifies control from a microcontroller or test sequencer. The 100 ohm maximum on-resistance must be included in the source-impedance budget because it creates attenuation when feeding a finite input impedance. Matched switch characteristics of 16 ohm maximum reduce variation between channels, while flatness of 10 ohm maximum supports more consistent calibration. Use the manufacturer signal-range limits and account for leakage, capacitance, and acquisition settling time in the complete front-end design.
Direkomendasikan
Precision Signal Conditioning
The MAX350CPN+ is useful for precision signal conditioning when several conditioned channels must reach a common amplifier, converter, or measurement block. Bidirectional conduction permits flexible test and calibration routing, and the dual 4:1 organization provides two independent selection paths. With a maximum on-resistance of 100 ohm, the device is best suited to low-frequency signals where insertion loss can be accepted or compensated. The specified 16 ohm maximum matching between switches limits channel-to-channel resistance variation, while the 10 ohm maximum flatness characteristic supports predictable transfer behavior. Place the mux close to the sensitive node, use a continuous ground plane, and buffer the output when the receiving circuit presents a high input impedance.
Direkomendasikan
Communication Interface Routing
The MAX350CPN+ can support low-frequency communication routing in instrumentation and control equipment where multiple external lines share a common interface. Its bidirectional operation helps simplify direction changes, and the serial control bus reduces the number of discrete selector commands required by the host controller. The 100 ohm maximum on-resistance can materially attenuate high-impedance signals, so the design should confirm that the logic levels, signal amplitude, and bandwidth remain within the manufacturer specifications. The DIP package supports through-hole cards and legacy communication instruments, while the dual multiplexers allow two independent paths to share a controller. Add input protection and impedance-matched drivers where the routed lines leave the board.
Direkomendasikan
Laboratory Instrumentation
The MAX350CPN+ fits laboratory instruments that switch several low-frequency inputs into a shared measurement chain. Two 4:1 sections provide flexible routing without requiring many mechanical controls, and serial control allows an embedded controller to select channels programmatically. The matched, relatively flat on-resistance characteristic improves repeatability across switched paths compared with an uncontrolled resistance spread. Because the device is intended primarily for low-frequency routing, engineers should evaluate bandwidth and capacitance for high-speed instrumentation before using it. A solid analog ground, short common-node routing, and local bypass capacitors help preserve measurement integrity, while a socket or carefully designed through-hole footprint simplifies serviceability.
Direkomendasikan
Legacy Through-Hole Control Boards
The MAX350CPN+ suits legacy industrial controllers, analyzers, and educational laboratory boards that use through-hole DIP components. The 18-pin package is straightforward to assemble, inspect, and replace, while the serial control reduces the number of host-controller pins needed for channel selection. Its dual 4:1 organization can support two independently switched groups, and bidirectional conduction makes the part useful for both source and destination routing. Maintain compatibility with the original system by checking supply polarity, logic thresholds, control timing, and maximum signal voltage against the manufacturer datasheet. The through-hole form also makes the device suitable for prototypes where surface-mount assembly equipment is unavailable.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk MAX350CPN+ — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | MAX350CPN |
|---|---|---|
| Brand | Analog Devices | Analog Devices |
| Package | 18-PDIP | 18-PDIP - same package |
| Circuit Configuration | Dual 4:1 | Dual 4:1 |
| Total Channels | 8 channels | 8 channels |
| Maximum On-Resistance | 100 ohm | 100 ohm |
| On-Resistance Matching | 16 ohm maximum | 16 ohm maximum |
| On-Resistance Flatness | 10 ohm maximum | 10 ohm maximum |
| Dual-Supply Range | +/-2.7 V to +/-8 V | +/-2.7 V to +/-8 V |
| Control Interface | Serial | Serial |
| Signal Direction | Bidirectional | Bidirectional |
Diferensiator Kunci
- Two independent 4:1 selectors in one package (vsMAX350CPN)
- Matched switch resistance improves channel consistency (vsMAX350CPN)
- Bidirectional routing with serial control (vsMAX350CPN)
Catatan Desain
Route the common and switched analog nodes as short, direct traces on the same PCB layer where practical. Avoid placing the serial-control traces between sensitive analog paths, and provide an uninterrupted ground plane beneath and around the device. Because the mux introduces up to 100 ohm of resistance, keep the receiving amplifier or converter close enough that divider action with source and input impedances is included in the error budget.
Check the source impedance, load impedance, frequency, and input capacitance before treating the MAX350CPN+ as a transparent switch. A 100 ohm maximum on-resistance can create meaningful attenuation with high-impedance sources, and switch capacitance can reduce settling time. Add a buffer when the destination requires low input impedance, and validate the complete transfer response with the actual source and load rather than relying only on the nominal on-resistance.
Follow the manufacturer datasheet for supply-decoupling values and placement. Place each required bypass capacitor adjacent to its supply pin and connect it to a low-impedance ground return. Do not infer the single-supply limits or logic thresholds from the dual-supply range alone; those values determine whether the serial-control signals are recognized correctly and whether the analog signal remains inside the permitted common-mode range.
Do not substitute MAX350CPN for MAX350CPN+ without checking the ordering table and production requirements. The cross-reference identifies matching terminals, package characteristics, and principal performance parameters, but commercial qualifiers, markings, and environmental requirements may differ. For new production, use the exact ordering code, inspect the incoming parts, and verify all exposed and through-hole connections against the manufacturer pin table.
Informasi Konformitas
The MAX350 family is an analog interface multiplexer rather than an automotive-qualified device. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals statements are not present in the verified excerpts.