Analog Devices

MAX350CPN+ - Dual 4:1 Multiplexer, 100 ohm | Analog Devices

MPN: MAX350CPN+ ✓ Aktif
+/-2.7 V to +/-8 V Vdss 100 ohm Rds(on) 18-pin plastic DIP Package
MOQ: 1 |

MAX350CPN+ Ringkasan

Analog Devices MAX350CPN+ is a dual 4:1 analog multiplexer with 100 ohm maximum on-resistance, housed in an 18-pin plastic DIP package. It combines two independently controlled 4:1 selectors, providing eight channels of analog routing while supporting bidirectional signal conduction.

An analog multiplexer is an interface IC that connects one shared signal path to multiple inputs or one input to multiple outputs. The MAX350 belongs to the broader switch and multiplexer hierarchy, where low on-resistance, matched switch characteristics, and serial control are important for preserving signal integrity in test, measurement, and communication systems.

The MAX350 family provides on-resistance matched between switches to 16 ohm maximum and flat to 10 ohm maximum over the specified signal range. Its 100 ohm maximum on-resistance suits low-frequency analog routing, while serial control reduces the number of control inputs required on a constrained board. The dual 4:1 organization allows two multiplexers to operate as independent routing pairs.

The device supports continuous operation from dual supplies of ±2.7 V to ±8 V. It also supports a single-supply operating mode, although the complete single-supply limits must be confirmed in the manufacturer datasheet before final rail planning. Bidirectional conduction means the selected signal may travel into or out of the common terminal without changing the switch architecture.

Typical uses include automated test equipment, data-acquisition systems, instrumentation, signal routing, and communication equipment. In each case, the serial interface reduces control-line count while the matched low on-resistance helps minimize channel-dependent attenuation. The 18-pin DIP package is appropriate for through-hole prototype, legacy, and industrial assembly where surface-mount packaging is not required.

When laying out a board, keep common and switched traces short, provide a solid ground reference, and route control signals away from sensitive analog paths. Confirm supply sequencing, logic-level thresholds, signal-range limits, and exposed-pin assignments against the manufacturer datasheet before manufacturing.

This page combines manufacturer specifications, verified sourcing information, drop-in replacement analysis, application guidance, and design considerations to support component selection and PCB implementation.

Pilihan pengganti yang segera untuk MAX350CPN+ — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

MAX350CPN

✅ Masuk Drop-In
📦 18-PDIP
Uses the same 18-PDIP footprint and terminal configuration with consistent principal performance parameters; no quantified electrical difference is stated in the cross-reference result.

📋 Alternatif rujukan (tidak dalam katalog)

MAX350CPN+ Spesifikasi

Number of Circuits 2 circuits
Multiplexer Configuration Dual 4:1
Number of Channels 8 channels
Maximum On-Resistance 100 ohm
On-Resistance Matching Between Switches 16 ohm maximum
On-Resistance Flatness 10 ohm maximum
Signal Conduction Direction Bidirectional
Dual-Supply Operating Range +/-2.7 V to +/-8 V
Control Interface Serial
Package Type 18-pin plastic DIP
Package Pin Count 18 pins
Jenis Pemasangan Through-hole

Panduan Konfigurasi Pin MAX350CPN+ 18 pins

Konfigurasi pin untuk MAX350CPN+ (18 pins pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.

Garis bentuk pengecah pakai 18 pins untuk MAX350CPN+

Tiada data garisan pin yang diperoleh untuk MAX350CPN+.

Rujuk kepada lembaran data untuk konfigurasi pin penuh.

Aplikasi Biasa

MAX350CPN+ patut untuk 6 aplikasis: Automated Test Equipment, Data Acquisition Systems, Precision Signal Conditioning, Communication Interface Routing, Laboratory Instrumentation, Legacy Through-Hole Control Boards.

🖥️

Automated Test Equipment

The MAX350CPN+ fits automated test systems that must route one analog measurement path among several sources or destinations. Two independent 4:1 circuits provide eight switched channels, while serial control reduces the number of parallel control lines required from the test controller. Bidirectional conduction allows the same routing fabric to support different signal directions. Its maximum on-resistance of 100 ohm and switch matching to 16 ohm maximum help control channel-dependent errors, although the selected node may require buffering when driving a high-impedance instrument. The 18-pin through-hole package also remains practical for legacy test fixtures, laboratory systems, and industrial controller boards built with plated-through-hole assembly.

📡

Data Acquisition Systems

The MAX350CPN+ can multiplex several low-frequency analog inputs into shared acquisition circuitry in a data-acquisition system. Its two 4:1 sections allow eight switched inputs to be organized as independent routing groups, and the serial interface simplifies control from a microcontroller or test sequencer. The 100 ohm maximum on-resistance must be included in the source-impedance budget because it creates attenuation when feeding a finite input impedance. Matched switch characteristics of 16 ohm maximum reduce variation between channels, while flatness of 10 ohm maximum supports more consistent calibration. Use the manufacturer signal-range limits and account for leakage, capacitance, and acquisition settling time in the complete front-end design.

🔧

Precision Signal Conditioning

The MAX350CPN+ is useful for precision signal conditioning when several conditioned channels must reach a common amplifier, converter, or measurement block. Bidirectional conduction permits flexible test and calibration routing, and the dual 4:1 organization provides two independent selection paths. With a maximum on-resistance of 100 ohm, the device is best suited to low-frequency signals where insertion loss can be accepted or compensated. The specified 16 ohm maximum matching between switches limits channel-to-channel resistance variation, while the 10 ohm maximum flatness characteristic supports predictable transfer behavior. Place the mux close to the sensitive node, use a continuous ground plane, and buffer the output when the receiving circuit presents a high input impedance.

🌐

Communication Interface Routing

The MAX350CPN+ can support low-frequency communication routing in instrumentation and control equipment where multiple external lines share a common interface. Its bidirectional operation helps simplify direction changes, and the serial control bus reduces the number of discrete selector commands required by the host controller. The 100 ohm maximum on-resistance can materially attenuate high-impedance signals, so the design should confirm that the logic levels, signal amplitude, and bandwidth remain within the manufacturer specifications. The DIP package supports through-hole cards and legacy communication instruments, while the dual multiplexers allow two independent paths to share a controller. Add input protection and impedance-matched drivers where the routed lines leave the board.

📺

Laboratory Instrumentation

The MAX350CPN+ fits laboratory instruments that switch several low-frequency inputs into a shared measurement chain. Two 4:1 sections provide flexible routing without requiring many mechanical controls, and serial control allows an embedded controller to select channels programmatically. The matched, relatively flat on-resistance characteristic improves repeatability across switched paths compared with an uncontrolled resistance spread. Because the device is intended primarily for low-frequency routing, engineers should evaluate bandwidth and capacitance for high-speed instrumentation before using it. A solid analog ground, short common-node routing, and local bypass capacitors help preserve measurement integrity, while a socket or carefully designed through-hole footprint simplifies serviceability.

🏭

Legacy Through-Hole Control Boards

The MAX350CPN+ suits legacy industrial controllers, analyzers, and educational laboratory boards that use through-hole DIP components. The 18-pin package is straightforward to assemble, inspect, and replace, while the serial control reduces the number of host-controller pins needed for channel selection. Its dual 4:1 organization can support two independently switched groups, and bidirectional conduction makes the part useful for both source and destination routing. Maintain compatibility with the original system by checking supply polarity, logic thresholds, control timing, and maximum signal voltage against the manufacturer datasheet. The through-hole form also makes the device suitable for prototypes where surface-mount assembly equipment is unavailable.

What is the MAX350CPN+?
The MAX350CPN+ is a dual 4:1 analog multiplexer in an 18-pin plastic DIP package. According to the Analog Devices MAX350 product page, it provides eight total channels, 100 ohm maximum on-resistance, bidirectional conduction, and serial control. The device combines two independent 4:1 selectors and is intended for analog signal-routing, test, measurement, instrumentation, and communication equipment.
How many channels and circuits does MAX350CPN+ have?
The MAX350CPN+ contains two circuits, each configured as a 4:1 multiplexer, for eight channels in total. The verified distributor listing identifies the device as a 2-circuit IC switch with a 4:1 configuration, while the Analog Devices product page describes the MAX350 as a dual 4-channel multiplexer. Use the pin-description table in the manufacturer datasheet when assigning the eight switched terminals and common terminals.
What is the on-resistance of MAX350CPN+?
The MAX350CPN+ has a maximum on-resistance of 100 ohm. According to the Analog Devices MAX350 product page, on-resistance is matched between switches to 16 ohm maximum and remains flat to 10 ohm maximum over the specified signal range. These characteristics make the device appropriate for low-frequency analog routing where channel-dependent insertion loss and gain variation should remain controlled.
What voltage supplies does MAX350CPN+ operate from?
The MAX350CPN+ can operate continuously from dual supplies ranging from +2.7 V to +8 V and from -2.7 V to -8 V. The Analog Devices MAX350 product page states this dual-supply range explicitly. It also supports a single-supply mode, but the complete single-supply limits are not visible in the verified product-page excerpt, so use the manufacturer datasheet for the exact range and logic thresholds.
Can MAX350CPN+ conduct signals in both directions?
Yes, the MAX350CPN+ conducts signals equally well in either direction. The Analog Devices MAX350 product page identifies these devices as multiplexers that conduct bidirectionally. This allows a common terminal to serve as either the input or output of the selected analog path, simplifying test systems where the same routing fabric must accommodate several source and destination configurations.
What is the difference between MAX350CPN and MAX350CPN+?
MAX350CPN and MAX350CPN+ use the same 18-pin DIP package and are described as having consistent terminals, package characteristics, and principal performance parameters. The MAX350CPN+ is the ordered variant identified by the plus suffix, while MAX350CPN is the base ordering code. Check the manufacturer ordering table for any commercial, termination, or marking differences before substituting one for the other.
Is MAX350CPN+ a drop-in replacement for MAX350CPN?
MAX350CPN+ is a drop-in alternative for MAX350CPN because the comparison data identifies matching terminals and packages and states that replacement requires no board modification. Both use the 18-pin DIP format and represent the same dual 4:1 multiplexer function. Confirm supply tolerances, control timing, and temperature-grade requirements in the manufacturer datasheet before production substitution.
When should I choose MAX350CPN+ instead of another multiplexer?
Choose MAX350CPN+ when the design needs two independent 4:1 analog selectors, serial control, bidirectional routing, and an 18-pin DIP footprint. It is particularly suitable for through-hole test and measurement systems that need low-frequency analog multiplexing with a maximum on-resistance of 100 ohm. A different multiplexer may be preferable when surface-mount construction, wider signal-range support, or lower resistance is required.
Where can I download the MAX350CPN+ datasheet PDF?
The official MAX350 documentation is available through the Analog Devices product page at https://www.analog.com/en/products/max350.html. Select the manufacturer data-sheet resource from the Documentation section. The product page identifies the document as Data Sheet Rev. 1. Use the manufacturer PDF for authoritative pin assignments, timing, electrical characteristics, supply limits, and package drawings.
Where can I find the MAX350CPN+ pinout?
Use the pin-description table and package drawing in the Analog Devices MAX350 manufacturer datasheet. The MAX350CPN+ uses an 18-pin plastic DIP package, but the verified excerpts do not expose the numbered terminal names. Follow the datasheet numbering convention directly rather than inferring assignments from generic DIP sockets, and confirm common terminals, switched terminals, supply pins, ground, and serial-control connections before routing the PCB.
How should MAX350CPN+ be used in automated test equipment?
The MAX350CPN+ can route a low-frequency analog measurement path through two independent 4:1 selectors using its serial control interface. Its bidirectional conduction supports source and destination reconfiguration, while on-resistance matching to 16 ohm maximum reduces channel-dependent variation. Apply the device within the specified signal range and account for insertion loss when calculating measurement accuracy.
What design considerations matter for a MAX350CPN+ PCB layout?
Keep switched and common analog traces short, minimize loop area, and connect the device ground to a low-impedance plane. Keep the serial clock, data, and enable traces away from sensitive analog nodes, and place any required bypass capacitors close to their supply pins. Because the complete pinout and bypass recommendations are not visible in the verified excerpts, follow the manufacturer datasheet for final connections and layout values.
Is MAX350CPN+ suitable for low-frequency instrumentation?
The MAX350CPN+ is suitable for low-frequency instrumentation routing when the signal bandwidth and amplitude remain within the manufacturer specifications. Its maximum on-resistance of 100 ohm, matching to 16 ohm maximum, and flatness to 10 ohm maximum help limit channel-dependent errors. For high-impedance source paths, buffer the selected node because switch leakage and capacitance can influence accuracy.
Where can I buy MAX350CPN+ and check current lead time?
Use the Request a Quote form on this page to request MAX350CPN+ availability, current lead time, and order handling. The manufacturer product page lists the MAX350 in production, and the target package is supplied in tubes according to the technical listing. Supply conditions and lot availability can change, so obtain a written quotation for the exact MAX350CPN+ ordering code and required quantity.
What are the key specifications engineers should know about MAX350CPN+?
The key MAX350CPN+ specifications are two 4:1 circuits, eight total channels, 100 ohm maximum on-resistance, 16 ohm maximum matching between switches, and 10 ohm maximum on-resistance flatness. The Analog Devices product page also specifies bidirectional conduction, serial control, dual supplies from +2.7 V to +8 V, and an 18-pin plastic DIP package. These points define its core signal-routing and packaging capabilities.

Data referensi kejuruteraan untuk MAX350CPN+ — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Choose MAX350CPN+ when a new or maintained system requires two independent 4:1 analog selectors, bidirectional conduction, serial control, and a through-hole 18-pin DIP footprint. Its maximum on-resistance of 100 ohm makes it most appropriate for low-frequency routing where the complete source-to-destination impedance can remain acceptable. MAX350CPN is a pin- and package-compatible drop-in alternative when the base ordering code satisfies the required commercial and production requirements. Do not select either MAX350 variant for a design requiring very low insertion loss, high-frequency operation, or a surface-mount footprint without first checking the complete manufacturer electrical characteristics. Choose a lower-resistance or surface-mount multiplexer instead if those requirements dominate the design.

Perbandingan dengan Gantian

Parametr Produk Ini MAX350CPN
Brand Analog Devices Analog Devices
Package 18-PDIP 18-PDIP - same package
Circuit Configuration Dual 4:1 Dual 4:1
Total Channels 8 channels 8 channels
Maximum On-Resistance 100 ohm 100 ohm
On-Resistance Matching 16 ohm maximum 16 ohm maximum
On-Resistance Flatness 10 ohm maximum 10 ohm maximum
Dual-Supply Range +/-2.7 V to +/-8 V +/-2.7 V to +/-8 V
Control Interface Serial Serial
Signal Direction Bidirectional Bidirectional

Penyeberangsung Jelas

  • Two independent 4:1 selectors in one package (vsMAX350CPN)
  • Matched switch resistance improves channel consistency (vsMAX350CPN)
  • Bidirectional routing with serial control (vsMAX350CPN)

Catatan Desain

Route the common and switched analog nodes as short, direct traces on the same PCB layer where practical. Avoid placing the serial-control traces between sensitive analog paths, and provide an uninterrupted ground plane beneath and around the device. Because the mux introduces up to 100 ohm of resistance, keep the receiving amplifier or converter close enough that divider action with source and input impedances is included in the error budget.

Check the source impedance, load impedance, frequency, and input capacitance before treating the MAX350CPN+ as a transparent switch. A 100 ohm maximum on-resistance can create meaningful attenuation with high-impedance sources, and switch capacitance can reduce settling time. Add a buffer when the destination requires low input impedance, and validate the complete transfer response with the actual source and load rather than relying only on the nominal on-resistance.

Follow the manufacturer datasheet for supply-decoupling values and placement. Place each required bypass capacitor adjacent to its supply pin and connect it to a low-impedance ground return. Do not infer the single-supply limits or logic thresholds from the dual-supply range alone; those values determine whether the serial-control signals are recognized correctly and whether the analog signal remains inside the permitted common-mode range.

Do not substitute MAX350CPN for MAX350CPN+ without checking the ordering table and production requirements. The cross-reference identifies matching terminals, package characteristics, and principal performance parameters, but commercial qualifiers, markings, and environmental requirements may differ. For new production, use the exact ordering code, inspect the incoming parts, and verify all exposed and through-hole connections against the manufacturer pin table.

Maklumat Kesediaan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bosong logam timbal
Unknown
Bosong halogen
Unknown
Mineral konflik
Unknown

The MAX350 family is an analog interface multiplexer rather than an automotive-qualified device. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals statements are not present in the verified excerpts.

Data disahkan pada: 2026-11-18 — data yang disahkan dan disusun semula oleh pasukan kejuruteraan komponen XAIPART

Pencarian Berhubungan

MAX350CPN+ datasheet MAX350CPN+ pinout MAX350CPN+ datasheet pdf Analog Devices MAX350CPN+ MAX350CPN+ 100 ohm multiplexer MAX350CPN+ 18-PDIP MAX350CPN+ analog switch MAX350CPN+ vs MAX350CPN MAX350CPN+ drop-in replacement MAX350CPN+ cross reference MAX350CPN+ footprint MAX350CPN+ price MAX350CPN+ stock MAX350CPN+ lead time MAX350 dual 4:1 multiplexer

Komponen dan Tanda berkaitan

Analog Devices MAX350 MAX350CPN+ MAX350CPN dual 4:1 analog multiplexer analog multiplexer analog switch interface IC semiconductor serial control bidirectional conduction on-resistance signal matching on-resistance flatness 18-PDIP plastic DIP through-hole package dual power supply single-supply operation automated test equipment data acquisition laboratory instrumentation low-frequency signal routing
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ