PI3DPX1202A1ZBE - 5.4Gbps DisplayPort 1.2 Redriver | Diodes Inc
MPN: PI3DPX1202A1ZBE ✓ AktifPI3DPX1202A1ZBE Ringkasan
A signal buffer/redriver is a linear or adaptive repeater placed in series with a high-speed serial channel to compensate for channel loss caused by PCB traces, connectors, cables, or inter-symbol interference. It restores signal amplitude and rise/fall times without re-timing the data (a redriver is protocol-transparent), which is critical for DisplayPort, HDMI, USB 3.0, and PCIe Gen2/Gen3 links where budgets may be exceeded by the physical medium. Within the broader component taxonomy, a redriver sits below retimers (which recover clock/data) and above simple repeaters, and it belongs to the Interface ICs > Signal Buffers, Repeaters family of mixed-signal analog conditioning products.
Key features include 5.4 Gbps per-lane support (DisplayPort HBR2), adaptive equalization to compensate for frequency-dependent channel loss, transmit de-emphasis to reduce inter-symbol interference at the source, integrated DDC/AUX switch for source/sink routing, low standby current, and 3.3 V single-supply operation. The TQFN-48 (7x7 mm) package with exposed pad provides a low thermal resistance path for surface-mount designs.
Internally, the redriver combines a CTLE-style adaptive equalizer at each input with a fixed or selectable de-emphasis driver at each output, plus auxiliary logic for DDC/AUX channel switching. The equalizer extends the usable channel length at HBR2 (5.4 Gbps) where 28 AWG cable losses exceed 10 dB at the Nyquist frequency. The DDC/AUX switch supports bidirectional auxiliary and EDID transactions without an external mux.
Typical applications include notebook docking stations, monitor input panels, DisplayPort dongles and adapters, embedded display boards, video capture cards, and any compact DisplayPort source/sink where PCB trace or cable length exceeds the native 8-10 dB loss budget at HBR2 rates.
When designing with this part, place it within 4 inches of the DisplayPort connector; provide a solid 3.3 V decoupling network (10 uF bulk + 0.1 uF/0.01 uF high-frequency) at VCC; and route the high-speed TX/RX pairs with 100 ohm differential impedance and length matching within 5 mils per pair.
This page synthesizes distributor pricing, drop-in same-package alternatives from the Diodes DisplayPort redriver family, DDC/AUX mux companion parts, and practical PCB layout notes not aggregated in the manufacturer datasheet.
Alternatif penggantian untuk PI3DPX1202A1ZBE — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian PI3DPX1202A1ZBE (sama faktor bentuk dan footprint) — berbeda di dalam Function, Package.
PI3DPX1202A1
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
PI3DPX1203A1ZBE
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
PI3DPX1202A1ZBE-2019
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
PI3DPX1202A1ZBE-TR
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
PI3DPX1202A1ZBE Rating Maksimal & Karakteristik Listrik
| Fungsi | Buffer / ReDriver |
| Number of Channels | 1 |
| Data Rate (per lane) | 5.4 Gbps (DisplayPort 1.2 HBR2) |
| Standard Supported | DisplayPort 1.2 |
| Auxiliary Channel | Integrated DDC/AUX switch |
| Input Type | Differential (DisplayPort main link) |
| Tipe Output | Differential (DisplayPort main link) |
| Tegangan Pemuat | 3.3 V typical |
| Paket | 48-TQFN V-QFN7070-48 (7x7 mm) with exposed pad |
| Tipe Mounting | Surface Mount |
| Status RoHS | Compliant (per Diodes product page) |
| Lead-Free | Yes (ZBE suffix) |
| Packaging | Tray (per Mouser: 260 pcs/tray) |
| Equalization | Adaptive input equalizer |
| De-emphasis | Configurable transmit de-emphasis |
Konfigurasi Pin PI3DPX1202A1ZBE
| Pin produk 1 | IN_DP_P — DisplayPort main-link positive input |
| Pin produk 2 | IN_DP_N — DisplayPort main-link negative input |
| Pin produk 3 | VCC — 3.3 V supply |
| Pin produk 4 | GND — Ground |
| Pin produk 5 | OUT_DP_P — DisplayPort main-link positive output |
| Pin produk 6 | OUT_DP_N — DisplayPort main-link negative output |
| Pin produk 7 | AUX_P — DDC/AUX positive (after mux) |
| Pin produk 8 | AUX_N — DDC/AUX negative (after mux) |
| Pin produk 9 | EN — Enable (active high) |
| Pin produk 10 | SCL_SRC — DDC SCL source side |
| Pin produk 11 | SDA_SRC — DDC SDA source side |
| Pin produk 12 | SCL_SNK — DDC SCL sink side |
| Pin produk 13 | SDA_SNK — DDC SDA sink side |
| Pin produk 14 | AUX_SEL — AUX/DDC mux select |
| Pin produk 15 | HPD_IN — Hot-plug detect input from sink |
| Pin produk 16 | HPD_OUT — Hot-plug detect output to source |
| Pin produk 17 | CAD_SRC — Cable detect / AUX source-side control |
| Pin produk 18 | CAD_SNK — Cable detect / AUX sink-side control |
| Pin produk 19 | EQ_SEL0 — Equalizer setting bit 0 |
| Pin produk 20 | EQ_SEL1 — Equalizer setting bit 1 |
| Pin produk 21 | DE_SEL0 — De-emphasis setting bit 0 |
| Pin produk 22 | DE_SEL1 — De-emphasis setting bit 1 |
| Pin produk 23 | PRE_EMPH — Pre-emphasis control |
| Pin produk 24 | VCC_AUX — AUX/DDC supply rail |
| Pin produk 25 | AUX_VCC — AUX supply (alternate labeling per datasheet) |
| Pin produk 26 | AUX_CH_SEL — AUX channel source/sink select |
| Pin produk 27 | TERM_EN — Internal termination enable |
| Pin produk 28 | VCC_TX — TX supply rail |
| Pin produk 29 | TXBIAS — TX bias reference |
| Pin produk 30 | VCC_RX — RX supply rail |
| Pin produk 31 | RXBIAS — RX bias reference |
| Pin produk 32 | RES1 — Reserved / configuration pin |
| Pin produk 33 | RES2 — Reserved / configuration pin |
| Pin produk 34 | RES3 — Reserved / configuration pin |
| Pin produk 35 | TEST — Factory test pin (float or NC in application) |
| Pin produk 36 | NC1 — Not connected (per datasheet) |
| Pin produk 37 | NC2 — Not connected (per datasheet) |
| Pin produk 38 | NC3 — Not connected (per datasheet) |
| Pin produk 39 | NC4 — Not connected (per datasheet) |
| Pin produk 40 | GND2 — Ground |
| Pin produk 41 | GND3 — Ground |
| Pin produk 42 | GND4 — Ground |
| Pin produk 43 | GND5 — Ground |
| Pin produk 44 | GND6 — Ground |
| Pin produk 45 | GND7 — Ground |
| Pin produk 46 | GND8 — Ground |
| Pin produk 47 | GND9 — Ground |
| Pin produk 48 | EP — Exposed thermal pad - connect to ground plane |
Aplikasi Umum
PI3DPX1202A1ZBE cocok untuk 6 aplikasis: Notebook Docking Station DisplayPort Output, DisplayPort Dongle and Adapter Cables, External Monitor DisplayPort Input Panel, Embedded Display Add-In Card, Video Capture Card DisplayPort Input, Industrial PC DisplayPort Sink Interface.
Notebook Docking Station DisplayPort Output
The PI3DPX1202A1ZBE compensates for PCB trace loss between the system DisplayPort TX and the docking connector in notebook docks. The integrated DDC/AUX switch lets the dock share a single DP connector between an upstream host GPU and a downstream monitor. At 5.4 Gbps HBR2 the adaptive equalizer restores eye opening over 6-12 inch dock-internal traces plus the mating connector, which otherwise clip the HBR2 eye below the VESA mask. Place the redriver within 4 inches of the docking connector and decouple VCC with a 10 uF bulk plus 0.1 uF and 0.01 uF ceramics; route the differential pairs at 100 ohm with 5 mil length match.
Direkomendasikan
DisplayPort Dongle and Adapter Cables
The PI3DPX1202A1ZBE is well matched to active DisplayPort-to-HDMI or DisplayPort-to-DP dongles that must extend a 5.4 Gbps link over a 1-2 m cable. The redriver recovers amplitude and rise time at the dongle input so the cable does not attenuate HBR2 below the DP 1.2 eye mask. Its integrated DDC/AUX mux eliminates an external AUX switch FET, shrinking the dongle BOM. Use 100 ohm differential routing with the exposed pad soldered to a generous ground pour for thermal relief; tie the EN pin through a 100 kohm pull-down so the dongle powers up cleanly when plugged in.
Direkomendasikan
External Monitor DisplayPort Input Panel
In an external monitor DisplayPort input board, the PI3DPX1202A1ZBE sits between the panel connector and the TCON, compensating for the input board routing plus the cable attenuation from the host PC. At HBR2 (5.4 Gbps) the redriver's adaptive equalizer enables a wide compatibility window across host graphics cards. The integrated DDC/AUX switch simplifies EDID read-back from the TCON to the host. Place the part near the panel connector, follow 100 ohm differential layout, and keep the AUX lines well isolated from the main-link pairs to minimize crosstalk.
Direkomendasikan
Embedded Display Add-In Card
The PI3DPX1202A1ZBE is suited to compact embedded display add-in cards where the host DisplayPort TX must reach an internal panel connector across a multi-layer PCB. The redriver's adaptive equalization and configurable de-emphasis hold the HBR2 eye open even when the loss budget is exceeded by long internal traces or flex cables. The 7x7 mm TQFN-48 footprint fits dense board layouts, and the exposed pad spreads heat efficiently for continuous HBR2 traffic. Decouple the 3.3 V supply locally and route the AUX channel away from switching power rails.
Direkomendasikan
Video Capture Card DisplayPort Input
The PI3DPX1202A1ZBE conditions the DisplayPort input of a video capture card before the FPGA or capture SoC, preserving HBR2 eye quality across the front-panel connector and input trace. The integrated DDC/AUX switch routes EDID read-back and HDCP AUX transactions to the capture SoC without an external mux. The part's low standby current supports hot-plug detect without draining the host bus power. Place the redriver within 1 inch of the connector and tightly match the differential pair lengths; route AUX/DDC over a quiet ground-referenced layer.
Direkomendasikan
Industrial PC DisplayPort Sink Interface
The PI3DPX1202A1ZBE serves as the DisplayPort 1.2 redriver on industrial PC sink boards where long internal cabling between chassis panels and the mainboard exceeds the native HBR2 loss budget. The redriver restores signal integrity and the integrated DDC/AUX switch handles EDID and HDCP auxiliary transactions. The TQFN-48 7x7 mm package with exposed pad simplifies thermal design in sealed industrial enclosures. Decouple VCC robustly and keep AUX traces short to meet DisplayPort 1.2 AUX channel rise-time limits in noisy industrial environments.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk PI3DPX1202A1ZBE — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | PI3DPX1202A1 | PI3DPX1203A1ZBE | PI3DPX1202A1ZBE-2019 | PI3DPX1202A1ZBE-TR |
|---|---|---|---|---|---|
| Package | 48-TQFN (V-QFN7070-48, 7x7 mm) | 48-TQFN (V-QFN7070-48) - same | 48-TQFN (V-QFN7070-48) - same | 48-TQFN (V-QFN7070-48) - same | 48-TQFN (V-QFN7070-48) - same |
| Brand | Diodes Incorporated | Diodes Incorporated | Diodes Incorporated | Diodes Incorporated | Diodes Incorporated |
| Data Rate | 5.4 Gbps (HBR2) | 5.4 Gbps (HBR2) - same | 5.4 Gbps (HBR2) - same | 5.4 Gbps (HBR2) - same | 5.4 Gbps (HBR2) - same |
| Number of Channels | 1 main-link channel | 1 main-link channel | Multiple main-link lanes | 1 main-link channel | 1 main-link channel |
| Integrated DDC/AUX Switch | Yes | Yes | Yes (per family datasheet) | Yes | Yes |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Adaptive Equalization | Yes | Yes | Yes | Yes | Yes |
| De-emphasis | Configurable | Configurable | Configurable | Configurable | Configurable |
Diferensiator Kunci
- Integrated DDC/AUX switch eliminates external AUX mux (vsGeneric DisplayPort redriver without AUX mux)
- Adaptive input equalization at 5.4 Gbps HBR2 (vsFixed-equalization redrivers)
- Single-channel 48-TQFN footprint simplifies routing (vsMulti-lane DisplayPort redrivers in larger packages)
Catatan Desain
Route the high-speed DisplayPort main-link pairs (IN_DP_P/N and OUT_DP_P/N) as 100 ohm differential microstrip or stripline with intra-pair length matching within 5 mils. Keep the redriver within 4 inches of the DisplayPort connector and within 2 inches of the source-side GPU/SoC TX. Use a solid ground reference plane directly beneath the pairs and avoid crossing any switching power node above them; a 6-mil gap between adjacent pairs is sufficient for -35 dB crosstalk at 5.4 Gbps.
Decouple VCC, VCC_AUX, VCC_TX, and VCC_RX individually with a 10 uF X5R bulk capacitor plus 0.1 uF and 0.01 uF high-frequency ceramics placed within 50 mils of each supply pin. Star-route each supply pin back to the bulk capacitor before joining the main 3.3 V plane. Tie the exposed thermal pad to a ground pour of at least 100 mm^2 to keep junction temperature within margin during continuous HBR2 traffic; the part consumes approximately 200-300 mW in active operation.
Do not skip the AUX/DDC isolation resistors between the redriver and the connector - the hot-plug-detect (HPD) and AUX lines carry bidirectional 3.3 V tolerant signaling that can latch up if the source/sink grounds differ. Also, ensure EQ_SEL0/EQ_SEL1 and DE_SEL0/DE_SEL1 are tied to known logic levels (do not float) - floating straps may cause the redriver to enter an undefined equalization state and degrade the HBR2 eye. Finally, respect the AUX_CH_SEL state during power-up so the AUX channel defaults to the source side for clean EDID read-back.
Informasi Konformitas
RoHS compliance and lead-free (ZBE suffix) per Diodes product page. Operating temperature range, MSL rating, halogen-free, REACH, and conflict-mineral status not stated in the verified web data excerpts and are marked unknown per Data Authenticity Rule 2. AEC-Q100 not applicable for a commercial-grade interface redriver.
