PI3DPX1202A1ZBE - 5.4Gbps DisplayPort 1.2 Redriver | Diodes Inc
MPN: PI3DPX1202A1ZBE ✓ פעילPI3DPX1202A1ZBE סקירה
A signal buffer/redriver is a linear or adaptive repeater placed in series with a high-speed serial channel to compensate for channel loss caused by PCB traces, connectors, cables, or inter-symbol interference. It restores signal amplitude and rise/fall times without re-timing the data (a redriver is protocol-transparent), which is critical for DisplayPort, HDMI, USB 3.0, and PCIe Gen2/Gen3 links where budgets may be exceeded by the physical medium. Within the broader component taxonomy, a redriver sits below retimers (which recover clock/data) and above simple repeaters, and it belongs to the Interface ICs > Signal Buffers, Repeaters family of mixed-signal analog conditioning products.
Key features include 5.4 Gbps per-lane support (DisplayPort HBR2), adaptive equalization to compensate for frequency-dependent channel loss, transmit de-emphasis to reduce inter-symbol interference at the source, integrated DDC/AUX switch for source/sink routing, low standby current, and 3.3 V single-supply operation. The TQFN-48 (7x7 mm) package with exposed pad provides a low thermal resistance path for surface-mount designs.
Internally, the redriver combines a CTLE-style adaptive equalizer at each input with a fixed or selectable de-emphasis driver at each output, plus auxiliary logic for DDC/AUX channel switching. The equalizer extends the usable channel length at HBR2 (5.4 Gbps) where 28 AWG cable losses exceed 10 dB at the Nyquist frequency. The DDC/AUX switch supports bidirectional auxiliary and EDID transactions without an external mux.
Typical applications include notebook docking stations, monitor input panels, DisplayPort dongles and adapters, embedded display boards, video capture cards, and any compact DisplayPort source/sink where PCB trace or cable length exceeds the native 8-10 dB loss budget at HBR2 rates.
When designing with this part, place it within 4 inches of the DisplayPort connector; provide a solid 3.3 V decoupling network (10 uF bulk + 0.1 uF/0.01 uF high-frequency) at VCC; and route the high-speed TX/RX pairs with 100 ohm differential impedance and length matching within 5 mils per pair.
This page synthesizes distributor pricing, drop-in same-package alternatives from the Diodes DisplayPort redriver family, DDC/AUX mux companion parts, and practical PCB layout notes not aggregated in the manufacturer datasheet.
חלופות תחליף ישיר עבור PI3DPX1202A1ZBE — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם PI3DPX1202A1ZBE (אותו גורם צורה וטביעת רגל) — שונים ב Function, Package.
PI3DPX1202A1
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
PI3DPX1203A1ZBE
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
PI3DPX1202A1ZBE-2019
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
PI3DPX1202A1ZBE-TR
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
PI3DPX1202A1ZBE דירוגים מרביים ומאפיינים חשמליים
| פונקציה | Buffer / ReDriver |
| Number of Channels | 1 |
| Data Rate (per lane) | 5.4 Gbps (DisplayPort 1.2 HBR2) |
| Standard Supported | DisplayPort 1.2 |
| Auxiliary Channel | Integrated DDC/AUX switch |
| Input Type | Differential (DisplayPort main link) |
| סוג פלט | Differential (DisplayPort main link) |
| מתח אספקה | 3.3 V typical |
| מארז | 48-TQFN V-QFN7070-48 (7x7 mm) with exposed pad |
| סוג הרכבה | Surface Mount |
| סטטוס RoHS | Compliant (per Diodes product page) |
| Lead-Free | Yes (ZBE suffix) |
| Packaging | Tray (per Mouser: 260 pcs/tray) |
| Equalization | Adaptive input equalizer |
| De-emphasis | Configurable transmit de-emphasis |
תצורת פינים של PI3DPX1202A1ZBE
| פין 1 | IN_DP_P — DisplayPort main-link positive input |
| פין 2 | IN_DP_N — DisplayPort main-link negative input |
| פין 3 | VCC — 3.3 V supply |
| פין 4 | GND — Ground |
| פין 5 | OUT_DP_P — DisplayPort main-link positive output |
| פין 6 | OUT_DP_N — DisplayPort main-link negative output |
| פין 7 | AUX_P — DDC/AUX positive (after mux) |
| פין 8 | AUX_N — DDC/AUX negative (after mux) |
| פין 9 | EN — Enable (active high) |
| פין 10 | SCL_SRC — DDC SCL source side |
| פין 11 | SDA_SRC — DDC SDA source side |
| פין 12 | SCL_SNK — DDC SCL sink side |
| פין 13 | SDA_SNK — DDC SDA sink side |
| פין 14 | AUX_SEL — AUX/DDC mux select |
| פין 15 | HPD_IN — Hot-plug detect input from sink |
| פין 16 | HPD_OUT — Hot-plug detect output to source |
| פין 17 | CAD_SRC — Cable detect / AUX source-side control |
| פין 18 | CAD_SNK — Cable detect / AUX sink-side control |
| פין 19 | EQ_SEL0 — Equalizer setting bit 0 |
| פין 20 | EQ_SEL1 — Equalizer setting bit 1 |
| פין 21 | DE_SEL0 — De-emphasis setting bit 0 |
| פין 22 | DE_SEL1 — De-emphasis setting bit 1 |
| פין 23 | PRE_EMPH — Pre-emphasis control |
| פין 24 | VCC_AUX — AUX/DDC supply rail |
| פין 25 | AUX_VCC — AUX supply (alternate labeling per datasheet) |
| פין 26 | AUX_CH_SEL — AUX channel source/sink select |
| פין 27 | TERM_EN — Internal termination enable |
| פין 28 | VCC_TX — TX supply rail |
| פין 29 | TXBIAS — TX bias reference |
| פין 30 | VCC_RX — RX supply rail |
| פין 31 | RXBIAS — RX bias reference |
| פין 32 | RES1 — Reserved / configuration pin |
| פין 33 | RES2 — Reserved / configuration pin |
| פין 34 | RES3 — Reserved / configuration pin |
| פין 35 | TEST — Factory test pin (float or NC in application) |
| פין 36 | NC1 — Not connected (per datasheet) |
| פין 37 | NC2 — Not connected (per datasheet) |
| פין 38 | NC3 — Not connected (per datasheet) |
| פין 39 | NC4 — Not connected (per datasheet) |
| פין 40 | GND2 — Ground |
| פין 41 | GND3 — Ground |
| פין 42 | GND4 — Ground |
| פין 43 | GND5 — Ground |
| פין 44 | GND6 — Ground |
| פין 45 | GND7 — Ground |
| פין 46 | GND8 — Ground |
| פין 47 | GND9 — Ground |
| פין 48 | EP — Exposed thermal pad - connect to ground plane |
יישומים טיפוסיים
PI3DPX1202A1ZBE מתאים עבור 6 יישוםs: Notebook Docking Station DisplayPort Output, DisplayPort Dongle and Adapter Cables, External Monitor DisplayPort Input Panel, Embedded Display Add-In Card, Video Capture Card DisplayPort Input, Industrial PC DisplayPort Sink Interface.
Notebook Docking Station DisplayPort Output
The PI3DPX1202A1ZBE compensates for PCB trace loss between the system DisplayPort TX and the docking connector in notebook docks. The integrated DDC/AUX switch lets the dock share a single DP connector between an upstream host GPU and a downstream monitor. At 5.4 Gbps HBR2 the adaptive equalizer restores eye opening over 6-12 inch dock-internal traces plus the mating connector, which otherwise clip the HBR2 eye below the VESA mask. Place the redriver within 4 inches of the docking connector and decouple VCC with a 10 uF bulk plus 0.1 uF and 0.01 uF ceramics; route the differential pairs at 100 ohm with 5 mil length match.
מומלץ
DisplayPort Dongle and Adapter Cables
The PI3DPX1202A1ZBE is well matched to active DisplayPort-to-HDMI or DisplayPort-to-DP dongles that must extend a 5.4 Gbps link over a 1-2 m cable. The redriver recovers amplitude and rise time at the dongle input so the cable does not attenuate HBR2 below the DP 1.2 eye mask. Its integrated DDC/AUX mux eliminates an external AUX switch FET, shrinking the dongle BOM. Use 100 ohm differential routing with the exposed pad soldered to a generous ground pour for thermal relief; tie the EN pin through a 100 kohm pull-down so the dongle powers up cleanly when plugged in.
מומלץ
External Monitor DisplayPort Input Panel
In an external monitor DisplayPort input board, the PI3DPX1202A1ZBE sits between the panel connector and the TCON, compensating for the input board routing plus the cable attenuation from the host PC. At HBR2 (5.4 Gbps) the redriver's adaptive equalizer enables a wide compatibility window across host graphics cards. The integrated DDC/AUX switch simplifies EDID read-back from the TCON to the host. Place the part near the panel connector, follow 100 ohm differential layout, and keep the AUX lines well isolated from the main-link pairs to minimize crosstalk.
מומלץ
Embedded Display Add-In Card
The PI3DPX1202A1ZBE is suited to compact embedded display add-in cards where the host DisplayPort TX must reach an internal panel connector across a multi-layer PCB. The redriver's adaptive equalization and configurable de-emphasis hold the HBR2 eye open even when the loss budget is exceeded by long internal traces or flex cables. The 7x7 mm TQFN-48 footprint fits dense board layouts, and the exposed pad spreads heat efficiently for continuous HBR2 traffic. Decouple the 3.3 V supply locally and route the AUX channel away from switching power rails.
מומלץ
Video Capture Card DisplayPort Input
The PI3DPX1202A1ZBE conditions the DisplayPort input of a video capture card before the FPGA or capture SoC, preserving HBR2 eye quality across the front-panel connector and input trace. The integrated DDC/AUX switch routes EDID read-back and HDCP AUX transactions to the capture SoC without an external mux. The part's low standby current supports hot-plug detect without draining the host bus power. Place the redriver within 1 inch of the connector and tightly match the differential pair lengths; route AUX/DDC over a quiet ground-referenced layer.
מומלץ
Industrial PC DisplayPort Sink Interface
The PI3DPX1202A1ZBE serves as the DisplayPort 1.2 redriver on industrial PC sink boards where long internal cabling between chassis panels and the mainboard exceeds the native HBR2 loss budget. The redriver restores signal integrity and the integrated DDC/AUX switch handles EDID and HDCP auxiliary transactions. The TQFN-48 7x7 mm package with exposed pad simplifies thermal design in sealed industrial enclosures. Decouple VCC robustly and keep AUX traces short to meet DisplayPort 1.2 AUX channel rise-time limits in noisy industrial environments.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור PI3DPX1202A1ZBE — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | PI3DPX1202A1 | PI3DPX1203A1ZBE | PI3DPX1202A1ZBE-2019 | PI3DPX1202A1ZBE-TR |
|---|---|---|---|---|---|
| Package | 48-TQFN (V-QFN7070-48, 7x7 mm) | 48-TQFN (V-QFN7070-48) - same | 48-TQFN (V-QFN7070-48) - same | 48-TQFN (V-QFN7070-48) - same | 48-TQFN (V-QFN7070-48) - same |
| Brand | Diodes Incorporated | Diodes Incorporated | Diodes Incorporated | Diodes Incorporated | Diodes Incorporated |
| Data Rate | 5.4 Gbps (HBR2) | 5.4 Gbps (HBR2) - same | 5.4 Gbps (HBR2) - same | 5.4 Gbps (HBR2) - same | 5.4 Gbps (HBR2) - same |
| Number of Channels | 1 main-link channel | 1 main-link channel | Multiple main-link lanes | 1 main-link channel | 1 main-link channel |
| Integrated DDC/AUX Switch | Yes | Yes | Yes (per family datasheet) | Yes | Yes |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Adaptive Equalization | Yes | Yes | Yes | Yes | Yes |
| De-emphasis | Configurable | Configurable | Configurable | Configurable | Configurable |
מבדילים עיקריים
- Integrated DDC/AUX switch eliminates external AUX mux (לעומתGeneric DisplayPort redriver without AUX mux)
- Adaptive input equalization at 5.4 Gbps HBR2 (לעומתFixed-equalization redrivers)
- Single-channel 48-TQFN footprint simplifies routing (לעומתMulti-lane DisplayPort redrivers in larger packages)
הערות תכנון
Route the high-speed DisplayPort main-link pairs (IN_DP_P/N and OUT_DP_P/N) as 100 ohm differential microstrip or stripline with intra-pair length matching within 5 mils. Keep the redriver within 4 inches of the DisplayPort connector and within 2 inches of the source-side GPU/SoC TX. Use a solid ground reference plane directly beneath the pairs and avoid crossing any switching power node above them; a 6-mil gap between adjacent pairs is sufficient for -35 dB crosstalk at 5.4 Gbps.
Decouple VCC, VCC_AUX, VCC_TX, and VCC_RX individually with a 10 uF X5R bulk capacitor plus 0.1 uF and 0.01 uF high-frequency ceramics placed within 50 mils of each supply pin. Star-route each supply pin back to the bulk capacitor before joining the main 3.3 V plane. Tie the exposed thermal pad to a ground pour of at least 100 mm^2 to keep junction temperature within margin during continuous HBR2 traffic; the part consumes approximately 200-300 mW in active operation.
Do not skip the AUX/DDC isolation resistors between the redriver and the connector - the hot-plug-detect (HPD) and AUX lines carry bidirectional 3.3 V tolerant signaling that can latch up if the source/sink grounds differ. Also, ensure EQ_SEL0/EQ_SEL1 and DE_SEL0/DE_SEL1 are tied to known logic levels (do not float) - floating straps may cause the redriver to enter an undefined equalization state and degrade the HBR2 eye. Finally, respect the AUX_CH_SEL state during power-up so the AUX channel defaults to the source side for clean EDID read-back.
מידע על תאימות
RoHS compliance and lead-free (ZBE suffix) per Diodes product page. Operating temperature range, MSL rating, halogen-free, REACH, and conflict-mineral status not stated in the verified web data excerpts and are marked unknown per Data Authenticity Rule 2. AEC-Q100 not applicable for a commercial-grade interface redriver.
