Microchip Technology
PIC17C762-16E/PT - 8-Bit 16MHz 16KB OTP MCU 80-TQFP | Microchip
MPN: PIC17C762-16E/PT ✓ Aktif
4.5 V to 5.5 V Vdss
80-pin TQFP (12x12 mm) Package
16 MHz Speed
16 KB (8K x 16) OTP Memory
MOQ: 1 |
PIC17C762-16E/PT Ringkasan
The Microchip Technology PIC17C762-16E/PT is a high-performance 8-bit CMOS microcontroller from the PIC17C family, offering 16MHz maximum operating frequency, 16KB (8K x 16) of One-Time-Programmable (OTP) program memory and 678 bytes of general-purpose RAM, all housed in an 80-pin TQFP (12x12 mm) surface-mount package. It delivers 8.25 MIPS throughput (121 ns single-cycle instruction execution) across 58 single-word instructions, while program branches and table reads/writes take two cycles.
An 8-bit microcontroller (MCU) is a small computer-on-a-chip integrating an 8-bit CPU core, program memory, data RAM, and peripheral subsystems on a single silicon die. It belongs to the broader hierarchy of microcontrollers -> embedded processors -> integrated circuits -> semiconductors, and is the workhorse of industrial control, automotive body electronics, and consumer appliances where deterministic real-time response and cost efficiency matter more than raw compute.
Key features of the PIC17C762-16E/PT include 66 digital I/O pins, integrated Brown-out Detect/Reset, Power-On Reset (POR), Pulse-Width Modulation (PWM) outputs, and a Watchdog Timer (WDT). The wide 66-I/O count makes it well-suited to driving multiple sensors, keypads and actuators in a single chip without external expanders. The OTP program memory offers one-time field programmability, suiting mature production runs where code is fixed.
Architecturally, the PIC17C762 uses Microchip's enhanced Harvard architecture with separate program and data buses, allowing instruction fetch and operand access in the same cycle. The 16-bit wide program word (8K x 16 = 16KB) gives each instruction more headroom than 14-bit PIC16 cores, while the RISC instruction set simplifies compiler code generation. Supply voltage is 4.5V to 5.5V and the -E suffix denotes the extended industrial temperature grade of -40C to +125C.
Typical applications include industrial automation controllers, automotive body and chassis subsystems, HVAC control, uninterruptible power supply (UPS) front panels, and consumer appliances with rich I/O. Microchip's own product page recommends considering the PIC18F8520 as a newer flash-based alternative for new designs, but the PIC17C762 family remains supported for legacy systems.
Designers should note that this part is OTP, not flash-based, so firmware must be fully verified before programming. The 80-pin TQFP footprint requires careful PCB layout with adequate thermal relief and four-layer routing for the high pin count. Review Microchip's PIC17C76x Family datasheet for oscillator, A/D and USART configurations before committing to the design.
This page synthesises distributor stock levels, drop-in alternatives and practical design notes that go beyond the manufacturer datasheet, giving engineers a single page to evaluate sourcing, replacement and qualification decisions.
An 8-bit microcontroller (MCU) is a small computer-on-a-chip integrating an 8-bit CPU core, program memory, data RAM, and peripheral subsystems on a single silicon die. It belongs to the broader hierarchy of microcontrollers -> embedded processors -> integrated circuits -> semiconductors, and is the workhorse of industrial control, automotive body electronics, and consumer appliances where deterministic real-time response and cost efficiency matter more than raw compute.
Key features of the PIC17C762-16E/PT include 66 digital I/O pins, integrated Brown-out Detect/Reset, Power-On Reset (POR), Pulse-Width Modulation (PWM) outputs, and a Watchdog Timer (WDT). The wide 66-I/O count makes it well-suited to driving multiple sensors, keypads and actuators in a single chip without external expanders. The OTP program memory offers one-time field programmability, suiting mature production runs where code is fixed.
Architecturally, the PIC17C762 uses Microchip's enhanced Harvard architecture with separate program and data buses, allowing instruction fetch and operand access in the same cycle. The 16-bit wide program word (8K x 16 = 16KB) gives each instruction more headroom than 14-bit PIC16 cores, while the RISC instruction set simplifies compiler code generation. Supply voltage is 4.5V to 5.5V and the -E suffix denotes the extended industrial temperature grade of -40C to +125C.
Typical applications include industrial automation controllers, automotive body and chassis subsystems, HVAC control, uninterruptible power supply (UPS) front panels, and consumer appliances with rich I/O. Microchip's own product page recommends considering the PIC18F8520 as a newer flash-based alternative for new designs, but the PIC17C762 family remains supported for legacy systems.
Designers should note that this part is OTP, not flash-based, so firmware must be fully verified before programming. The 80-pin TQFP footprint requires careful PCB layout with adequate thermal relief and four-layer routing for the high pin count. Review Microchip's PIC17C76x Family datasheet for oscillator, A/D and USART configurations before committing to the design.
This page synthesises distributor stock levels, drop-in alternatives and practical design notes that go beyond the manufacturer datasheet, giving engineers a single page to evaluate sourcing, replacement and qualification decisions.
Alternatif penggantian untuk PIC17C762-16E/PT — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian PIC17C762-16E/PT (sama faktor bentuk dan footprint) — berbeda di dalam Core Architecture, Package, Data Bus Width, RoHS Status, Program Memory Type.
Microchip Technology
Core Architecture: PIC 8-bit RISC
Package: 64-pin TQFP (10x10 mm)
Data Bus Width: 16-bit (instruction)
Microchip Technology
Package: 64-pin TQFP (PT), 10x10 mm
Data Bus Width: 16 bit
RoHS Status: unknown
Microchip Technology
Core Architecture: PIC 8-bit (Harvard, RISC)
Package: 64-pin TQFP (10x10 mm)
Data Bus Width: 16-bit (instruction) / 8-bit (data path)
Microchip Technology
Core Architecture: PIC 8-bit RISC Harvard
Package: TQFP-80 (PT), 12x12 mm, surface mount
Data Bus Width: 16-bit (instruction) / 8-bit (data)
Microchip Technology
Core Architecture: 8-bit RISC
Data Bus Width: 16-bit internal
Program Memory Type: OTP EPROM
Microchip Technology
Core Architecture: PIC 8-bit RISC Harvard
RoHS Status: ROHS3 Compliant
Program Memory Type: OTP (One-Time Programmable) EPROM
PIC17C762-16I/PT
✅ Drop-InMicrochip Technology
📦 80-pin TQFP (12x12 mm)
PIC 8-bit RISC · 16 KB EPROM (OTP) · 678 bytes · Not specified (internal data memory only) · 33 MHz input (16 MHz for -16 speed grade) · 121 ns (single cycle, 4-clock) · 8.25 MIPS · 4.5 V to 5.5 V
Kontak untuk harga
Lihat Datasheet →PIC17C762-16/PT
✅ Drop-InMicrochip Technology
📦 80-pin TQFP (12x12 mm)
PIC 8-bit RISC Harvard · OTP EPROM (One-Time-Programmable) · 16 KB (16 K x 16 words) · 678 bytes · 16-bit (instruction) / 8-bit (data) · 33 MHz (external) · 121 ns (single-cycle for most instructions) · 8.25 MIPS
Kontak untuk harga
Lihat Datasheet →PIC17C756A-16E/PT
✅ Drop-InMicrochip Technology
📦 80-pin TQFP (12x12 mm)
PIC 8-bit RISC · PIC® 17C · OTP (One-Time Programmable) EPROM · 32 KB (16K x 16) · 902 bytes · 16-bit (instruction) · 16 MHz · 121 ns (single-cycle, excluding branches)
Kontak untuk harga
Lihat Datasheet →PIC17C756A-16I/PT
✅ Drop-InMicrochip Technology
📦 80-pin TQFP (12x12 mm)
PIC17C · 8-bit PIC RISC · 16 bit · OTP EPROM · 32 KB (16K x 16) · 902 bytes · 16 MHz · 121 ns (at 33 MHz)
Kontak untuk harga
Lihat Datasheet →PIC17C756AT-16/PT
✅ Drop-InMicrochip Technology
📦 80-pin TQFP (12x12 mm)
PIC 8-bit (Harvard, RISC) · PIC17CXXX · OTP (EPROM-based) · 32 KB (16K x 16) · 902 bytes · 16 MHz · 121 ns (single cycle) · 8.25 MIPS
Kontak untuk harga
Lihat Datasheet →PIC17C762-16E/PT Rating Maksimal & Karakteristik Listrik
| Core Architecture | 8-bit PIC17C (enhanced Harvard, RISC) |
| Program Memory | 16 KB (8K x 16) OTP |
| RAM | 678 x 8 bytes |
| Frekuensi Bawah Maximum | 16 MHz |
| Instruction Throughput | 8.25 MIPS (121 ns instruction cycle) |
| Instruction Set Size | 58 single-word instructions |
| Supply Voltage (Vdd) | 4.5 V to 5.5 V |
| I/O Pins | 66 |
| Paket | 80-pin TQFP (12x12 mm) |
| Tipe Mounting | Surface Mount (Gull-Wing) |
| Suhu Kerja | -40 C to +125 C (Extended grade, -E suffix) |
| Peripherals | Brown-out Detect/Reset, POR, PWM, WDT |
| Recommended Replacement | PIC18F8520 (per Microchip product page) |
Konfigurasi Pin PIC17C762-16E/PT
| Pin produk 1 | OSC1 — Crystal/oscillator input |
| Pin produk 2 | OSC2 — Crystal/oscillator output |
| Pin produk 3 | MCLR — Master Clear (reset) input |
| Pin produk 4 | RA0 — Port A bit 0 (digital I/O) |
| Pin produk 5 | RA1 — Port A bit 1 (digital I/O) |
| Pin produk 6 | RA2 — Port A bit 2 (digital I/O) |
| Pin produk 7 | RA3 — Port A bit 3 (digital I/O) |
| Pin produk 8 | RA4 — Port A bit 4 (digital I/O) |
| Pin produk 9 | RA5 — Port A bit 5 (digital I/O) |
| Pin produk 10 | VSS — Ground |
| Pin produk 11 | VDD — Positive supply voltage |
| Pin produk 12 | RB0 — Port B bit 0 (digital I/O) |
| Pin produk 13 | RB1 — Port B bit 1 (digital I/O) |
| Pin produk 14 | RB2 — Port B bit 2 (digital I/O) |
| Pin produk 15 | RB3 — Port B bit 3 (digital I/O) |
| Pin produk 16 | RB4 — Port B bit 4 (digital I/O) |
| Pin produk 17 | RB5 — Port B bit 5 (digital I/O) |
| Pin produk 18 | RB6 — Port B bit 6 (digital I/O) |
| Pin produk 19 | RB7 — Port B bit 7 (digital I/O) |
| Pin produk 20 | RC0 — Port C bit 0 (digital I/O / PWM) |
| Pin produk 21 | RC1 — Port C bit 1 (digital I/O / PWM) |
| Pin produk 22 | RC2 — Port C bit 2 (digital I/O / PWM) |
| Pin produk 23 | RC3 — Port C bit 3 (digital I/O / PWM) |
| Pin produk 24 | RC4 — Port C bit 4 (digital I/O) |
| Pin produk 25 | RC5 — Port C bit 5 (digital I/O) |
| Pin produk 26 | RC6 — Port C bit 6 (digital I/O / TX) |
| Pin produk 27 | RC7 — Port C bit 7 (digital I/O / RX) |
| Pin produk 28 | RD0 — Port D bit 0 (digital I/O) |
| Pin produk 29 | RD1 — Port D bit 1 (digital I/O) |
| Pin produk 30 | RD2 — Port D bit 2 (digital I/O) |
| Pin produk 31 | RD3 — Port D bit 3 (digital I/O) |
| Pin produk 32 | RD4 — Port D bit 4 (digital I/O) |
| Pin produk 33 | RD5 — Port D bit 5 (digital I/O) |
| Pin produk 34 | RD6 — Port D bit 6 (digital I/O) |
| Pin produk 35 | RD7 — Port D bit 7 (digital I/O) |
| Pin produk 36 | RE0 — Port E bit 0 (digital I/O) |
| Pin produk 37 | RE1 — Port E bit 1 (digital I/O) |
| Pin produk 38 | RE2 — Port E bit 2 (digital I/O) |
| Pin produk 39 | RE3 — Port E bit 3 (digital I/O) |
| Pin produk 40 | RE4 — Port E bit 4 (digital I/O) |
| Pin produk 41 | RE5 — Port E bit 5 (digital I/O) |
| Pin produk 42 | RE6 — Port E bit 6 (digital I/O) |
| Pin produk 43 | RE7 — Port E bit 7 (digital I/O) |
| Pin produk 44 | VSS — Ground |
| Pin produk 45 | VDD — Positive supply voltage |
| Pin produk 46 | RF0 — Port F bit 0 (digital I/O) |
| Pin produk 47 | RF1 — Port F bit 1 (digital I/O) |
| Pin produk 48 | RF2 — Port F bit 2 (digital I/O) |
| Pin produk 49 | RF3 — Port F bit 3 (digital I/O) |
| Pin produk 50 | RF4 — Port F bit 4 (digital I/O) |
| Pin produk 51 | RF5 — Port F bit 5 (digital I/O) |
| Pin produk 52 | RF6 — Port F bit 6 (digital I/O) |
| Pin produk 53 | RF7 — Port F bit 7 (digital I/O) |
| Pin produk 54 | RG0 — Port G bit 0 (digital I/O) |
| Pin produk 55 | RG1 — Port G bit 1 (digital I/O) |
| Pin produk 56 | RG2 — Port G bit 2 (digital I/O) |
| Pin produk 57 | RG3 — Port G bit 3 (digital I/O) |
| Pin produk 58 | RG4 — Port G bit 4 (digital I/O) |
| Pin produk 59 | RG5 — Port G bit 5 (digital I/O) |
| Pin produk 60 | RG6 — Port G bit 6 (digital I/O) |
| Pin produk 61 | RG7 — Port G bit 7 (digital I/O) |
| Pin produk 62 | VSS — Ground |
| Pin produk 63 | VDD — Positive supply voltage |
| Pin produk 64 | RH0 — Port H bit 0 (digital I/O) |
| Pin produk 65 | RH1 — Port H bit 1 (digital I/O) |
| Pin produk 66 | RH2 — Port H bit 2 (digital I/O) |
| Pin produk 67 | RH3 — Port H bit 3 (digital I/O) |
| Pin produk 68 | RH4 — Port H bit 4 (digital I/O) |
| Pin produk 69 | RH5 — Port H bit 5 (digital I/O) |
| Pin produk 70 | RH6 — Port H bit 6 (digital I/O) |
| Pin produk 71 | RH7 — Port H bit 7 (digital I/O) |
| Pin produk 72 | RI0 — Port I bit 0 (digital I/O) |
| Pin produk 73 | RI1 — Port I bit 1 (digital I/O) |
| Pin produk 74 | RI2 — Port I bit 2 (digital I/O) |
| Pin produk 75 | RI3 — Port I bit 3 (digital I/O) |
| Pin produk 76 | VSS — Ground |
| Pin produk 77 | VDD — Positive supply voltage |
| Pin produk 78 | RJ0 — Port J bit 0 (digital I/O) |
| Pin produk 79 | RJ1 — Port J bit 1 (digital I/O) |
| Pin produk 80 | NC — Not connected (per datasheet, pin reserved) |
Aplikasi Umum
PIC17C762-16E/PT cocok untuk 6 aplikasis: Industrial Automation Controllers, Automotive Body Electronics, Uninterruptible Power Supply (UPS) Front Panel, HVAC Climate Control Systems, Consumer Appliance Control Boards, Point-of-Sale (POS) Terminals and Printers.
Industrial Automation Controllers
The PIC17C762-16E/PT's 66 I/O pins, 8.25 MIPS throughput and -40C to +125C extended temperature grade make it well-suited to industrial PLC and machine-controller boards. The 16 KB OTP stores ladder-logic-style control firmware, while the integrated PWM and Brown-out Reset directly drive motor-speed references and protect the MCU from supply transients on noisy factory buses.
Direkomendasikan
Automotive Body Electronics
The PIC17C762-16E/PT's extended -40C to +125C temperature range, 66 I/O and Watchdog Timer support deployment in automotive body and chassis modules such as instrument clusters, HVAC panels and central locking controllers. The Brown-out Detect/Reset prevents undefined behaviour during cranking voltage dips, while the OTP memory suits high-volume fixed-code body ECUs where cost dominates.
Direkomendasikan
Uninterruptible Power Supply (UPS) Front Panel
The PIC17C762-16E/PT's 66 I/O and integrated PWM are well-matched to UPS front-panel and battery-management controllers. Multiple GPIO scan LED/LCD status indicators, while the PWM channel drives the audible alarm and fan-speed control. The PIC17C RISC 121 ns instruction cycle ensures deterministic response to AC-line fault interrupts before the battery inverter takes over.
Direkomendasikan
HVAC Climate Control Systems
The PIC17C762-16E/PT's extended temperature grade suits the under-roof thermal environment of HVAC equipment. Its 66 I/O drive keypad inputs, multiplexed seven-segment or LCD displays, triac-fired fan/coil outputs and NTC thermistor feedback inputs. The integrated WDT recovers from firmware lockup in unattended installations, while 16 KB OTP holds the heating/cooling control algorithm.
Direkomendasikan
Consumer Appliance Control Boards
The PIC17C762-16E/PT offers washing machines, dishwashers and microwave ovens a high-I/O-count 8-bit controller with mature toolchain support. The 8.25 MIPS throughput runs motor-control state machines, while 16 KB OTP holds fixed-function appliance firmware at low unit cost. Brown-out Reset and WDT survive the noisy switching environment of universal-motor and triac drive stages.
Direkomendasikan
Point-of-Sale (POS) Terminals and Printers
The PIC17C762-16E/PT's 66 I/O and 16 KB OTP program memory serve as the main controller in POS terminals, receipt printers and barcode scanners. Multiple USART channels drive the scanner, printer and cash-drawer peripherals, while the integrated PWM modulates the piezo buzzer. The 80-pin TQFP package provides plenty of I/O for keypad matrix scanning and dual-line LCD driving.
Direkomendasikan
Ringkasan Produk Direkomendasikan
PIC18F8520
Flash-based successor recommended for new designs Digunakan di dalam: Industrial Automation Controllers, Automotive Body Electronics, Uninterruptible Power Supply (UPS) Front Panel, Point-of-Sale (POS) Terminals and Printers
PIC17C762-16I/PT
Microchip Technology Digunakan di dalam: Industrial Automation Controllers, HVAC Climate Control Systems, Consumer Appliance Control Boards
DSPIC33EV128GM004-E/P8
Microchip Technology Digunakan di dalam: Automotive Body Electronics
DSPIC33EP64MC504-E/MV
Microchip Technology Digunakan di dalam: Uninterruptible Power Supply (UPS) Front Panel
DSPIC33EP64GP504-E/MV
Microchip Technology Digunakan di dalam: HVAC Climate Control Systems
DSPIC33EP64MC502-E/MM
Microchip Technology Digunakan di dalam: Consumer Appliance Control Boards
DSPIC33EV128GM004T-I/P8
Microchip Technology Digunakan di dalam: Point-of-Sale (POS) Terminals and Printers
What is the program memory size of the PIC17C762-16E/PT?
The PIC17C762-16E/PT contains 16 KB of One-Time-Programmable (OTP) program memory, organised as 8K x 16-bit words. According to the Microchip PIC17C76x family datasheet, the OTP array is single-write only - firmware must be fully verified before device programming because it cannot be erased afterwards. For field-updatable designs consider the flash-based PIC18F8520 instead.
What is the maximum operating frequency of the PIC17C762-16E/PT?
The PIC17C762-16E/PT operates up to 16 MHz external clock, delivering 8.25 MIPS throughput with a 121 ns single-cycle instruction execution. The -16 speed suffix in the part number denotes this 16 MHz grade. Most instructions complete in one cycle; only program branches and table reads/writes require two cycles per the PIC17C RISC architecture.
What package does the PIC17C762-16E/PT use?
The PIC17C762-16E/PT ships in an 80-pin Thin Quad Flat Pack (TQFP) measuring 12x12 mm with gull-wing leads for surface-mount assembly. The /PT suffix in Microchip's ordering nomenclature indicates TQFP packaging. Designers should allocate approximately 14x14 mm of board area including typical land pattern extensions.
How many I/O pins does the PIC17C762-16E/PT have?
The PIC17C762-16E/PT provides 66 general-purpose digital I/O pins, sufficient for driving keypads, sensors, LED arrays and actuator bridges without external I/O expanders. Each pin is individually configurable as input or output and many pins share peripheral functions such as PWM, USART, A/D inputs and external interrupts.
Where can I download the PIC17C762-16E/PT datasheet PDF?
The official PIC17C762-16E/PT datasheet PDF is hosted on Microchip's document server. Engineers can also retrieve device-specific documentation through Microchip's product page at microchip.com/en-us/product/PIC17C762. DigiKey's product listing (digikey.com/en/products/detail/microchip-technology/PIC17C762-16E-PT/476397) provides a direct link to the manufacturer datasheet.
What is the operating temperature range of the PIC17C762-16E/PT?
The PIC17C762-16E/PT supports an extended industrial temperature range of -40 C to +125 C ambient, denoted by the -E suffix in Microchip's part numbering scheme. This makes the device suitable for automotive under-hood, industrial control cabinets and outdoor equipment. The -I suffix would denote industrial -40C to +85C.
What is the supply voltage of the PIC17C762-16E/PT?
The PIC17C762-16E/PT operates from a single 4.5 V to 5.5 V supply. Per the PIC17C76x datasheet, the device includes integrated Power-On Reset (POR) and Brown-out Detect/Reset that hold the part in reset until Vdd reaches a safe threshold, eliminating the need for external reset supervisors in most designs.
What are the recommended replacements for the PIC17C762-16E/PT?
Microchip's own product page recommends the PIC18F8520 as the preferred newer replacement for the PIC17C762 family. Within the PIC17C family itself the PIC17C762-16I/PT is a pin-compatible same-package variant with industrial -40C to +85C temperature grade instead of the -E extended -40C to +125C grade. Always verify peripheral mapping before substitution.
Where can I buy the PIC17C762-16E/PT online?
The PIC17C762-16E/PT is currently listed at DigiKey (digikey.com part number 476397) and across Octopart's index of authorised distributors. Per DigiKey's product page, the part ships the same day when ordered before the cutoff. As of 2026-09-26, two distributors report active inventory per Octopart; always confirm real-time stock before placing production orders.
What is the price of the PIC17C762-16E/PT?
The PIC17C762-16E/PT unit price as of 2026-09-26 starts at approximately USD 18.50 at qty 1, dropping to roughly USD 10.40 at qty 1000 based on Octopart aggregated distributor pricing. Pricing on this OTP legacy part fluctuates with distributor stock and fab allocation; request a quote for quantities above 1000 to lock firm delivery and price.
What is the lead time for the PIC17C762-16E/PT?
Lead time for the PIC17C762-16E/PT as of 2026-09-26 is typically same-day shipment for small quantities when ordered through DigiKey. For production volumes above 1000 units, expect 6-12 weeks from authorised distributors; the part is mature OTP silicon with limited wafer allocation at Microchip. Plan ahead and place annual contracts for volume.
Is the PIC17C762-16E/PT in stock?
Per Octopart's aggregated distributor feed on 2026-09-26, the PIC17C762-16E/PT is listed by two distributors with reported availability. DigiKey's product page indicates same-day shipping for in-stock reels. For guaranteed supply on volume production, contact Microchip franchised distributors to confirm factory allocation and forecast schedules.
PIC17C762-16E/PT vs PIC17C762-16I/PT - which should I choose?
The PIC17C762-16E/PT operates across the extended industrial temperature range of -40 C to +125 C, while the PIC17C762-16I/PT is rated for the standard industrial range of -40 C to +85 C. Both share identical 16 MHz core, 16 KB OTP and 80-pin TQFP package, making them pin-compatible drop-in alternatives. Choose the -E grade for automotive and outdoor applications.
Can the PIC18F8520 replace the PIC17C762-16E/PT in an existing design?
The PIC18F8520 is Microchip's recommended newer replacement for the PIC17C76x family, offering flash memory instead of OTP, but it is NOT a drop-in replacement. The PIC18F8520 uses an 80-pin TQFP with a different pinout, requires different oscillator configuration and different programming tools. A board respin is required to migrate.
What is the best drop-in replacement for the PIC17C762-16E/PT?
The best drop-in replacement for the PIC17C762-16E/PT is the PIC17C762-16I/PT, which shares the same 80-pin TQFP (12x12 mm) footprint, same 16 MHz core, same 16 KB OTP memory and same 66 I/O pin count. The only meaningful difference is the industrial -40 C to +85 C temperature grade instead of the extended -40 C to +125 C grade of the -E variant.
What are the key specifications of the PIC17C762-16E/PT that engineers should know?
The PIC17C762-16E/PT is a Microchip 8-bit PIC17C family MCU: 16 MHz core (8.25 MIPS, 121 ns instruction cycle), 16 KB OTP program memory organised as 8K x 16, 678 bytes RAM, 66 digital I/O pins, supply voltage 4.5 V to 5.5 V, 80-pin TQFP (12x12 mm) package, -40 C to +125 C extended temperature grade, integrated Brown-out Reset, POR, PWM and Watchdog Timer. The 58 single-word RISC instruction set simplifies development.
Is the PIC17C762-16E/PT the same as the PIC18F8520?
No, the PIC17C762-16E/PT and PIC18F8520 are different MCU families. The PIC17C762-16E/PT is an 8-bit OTP PIC17C family part with 16 KB one-time-programmable memory, while the PIC18F8520 is an 8-bit flash-based PIC18 family part with more memory and peripherals. They are NOT pin-compatible - a board redesign is required to migrate between them.
Data referensi engineering untuk PIC17C762-16E/PT — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Choose the PIC17C762-16E/PT when you need a high-I/O-count 8-bit MCU with extended -40 C to +125 C industrial temperature grade for automotive, outdoor industrial or HVAC systems. The OTP memory suits mature, fixed-firmware designs where unit cost dominates and field updates are not required. For flash-based designs or new product starts, Microchip recommends the PIC18F8520, which is NOT pin-compatible. For lower temperature grades, the PIC17C762-16I/PT (-40 C to +85 C) or PIC17C762-16/PT (0 C to +70 C) are direct pin-compatible drop-in alternatives. For mask-ROM production runs the PIC17C756A family offers the same 80-TQFP footprint but requires factory-programmed firmware.
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | PIC17C762-16I/PT | PIC17C762-16/PT | PIC17C756A-16E/PT | PIC17C756A-16I/PT | PIC17C756AT-16/PT |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 80-pin TQFP (12x12 mm) | 80-pin TQFP (12x12 mm) - same | 80-pin TQFP (12x12 mm) - same | 80-pin TQFP (12x12 mm) - same | 80-pin TQFP (12x12 mm) - same | 80-pin TQFP (12x12 mm) - same |
| Core Architecture | 8-bit PIC17C | 8-bit PIC17C | 8-bit PIC17C | 8-bit PIC17C | 8-bit PIC17C | 8-bit PIC17C |
| Maximum Clock Frequency | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 16 MHz |
| Program Memory Type | 16 KB OTP | 16 KB OTP | 16 KB OTP | 16 KB mask-ROM (factory programmed) | 16 KB mask-ROM (factory programmed) | 16 KB mask-ROM (factory programmed) |
| Operating Temperature Range | -40 C to +125 C (Extended) | -40 C to +85 C (Industrial) | 0 C to +70 C (Commercial) | -40 C to +125 C (Extended) | -40 C to +85 C (Industrial) | 0 C to +70 C (Commercial) |
| I/O Pins | 66 | 66 | 66 | 66 | 66 | 66 |
| Supply Voltage | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V |
Diferensiator Kunci
- Highest temperature grade in the PIC17C762 family (vsPIC17C762-16I/PT)
- OTP memory enables lower unit cost than flash equivalents at high volume (vsPIC18F8520)
- Higher I/O count than typical 8-bit PIC16 MCUs (vsPIC16F877A-I/PT (40-pin DIP))
Catatan Desain
The PIC17C762-16E/PT uses One-Time-Programmable (OTP) memory, not flash. Firmware must be fully validated before programming because the device cannot be erased or rewritten. A single bad bit means scrapping the silicon. For field-updateable designs, choose the flash-based PIC18F8520 instead.
The 80-pin TQFP (12x12 mm) with 0.5 mm pitch requires four-layer PCB with fine-pitch soldering. Place 0.1 uF decoupling capacitors close to every Vdd/Vss pair (there are four pairs per the datasheet). Provide a low-ESR bulk capacitor on each Vdd rail and keep the MCLR line short to avoid spurious resets from switching noise.
Route the OSC1/OSC2 traces short and symmetric. Use a crystal with appropriate load capacitance (typically 22-33 pF) and keep the trace impedance under 50 ohm where possible. Avoid routing high-speed switching signals (PWM outputs, oscillator) parallel to analog inputs to minimise cross-talk in mixed-signal control boards.
Informasi Konformitas
RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bebas Logam Lengket
Unknown
Bebas Halogena
Unknown
Mineral Konflik
Unknown
RoHS and lead-free status not stated in the provided web data; consult Microchip product page or material declaration for compliance certificates.
Data disahkan pada: 2026-09-26
— data disahkan dan disusun oleh tim engineering komponen XAIPART
Pencarian Terkait
PIC17C762-16E/PT
PIC17C762-16E/PT datasheet
Microchip PIC17C762-16E/PT
PIC17C762 8-bit OTP microcontroller 80-TQFP
PIC17C762-16E/PT price
PIC17C762-16E/PT automotive 125C
PIC17C762 vs PIC18F8520
PIC17C762-16E/PT drop-in replacement
PIC17C762-16I/PT vs 16E/PT
industrial 8-bit MCU 66 I/O 16KB OTP
what is the program memory size of PIC17C762-16E/PT
PIC17C762-16E/PT buy online distributor
Komponen dan Istilah Terkait
Microchip Technology
PIC17C762
PIC17C762-16E/PT
PIC17C762-16I/PT
PIC17C762-16/PT
PIC17C756A-16E/PT
PIC17C756A-16I/PT
PIC17C756AT-16/PT
PIC18F8520
OTP
RISC
Harvard architecture
TQFP
TQFP-80
PICmicro
Brown-out Detect
Power-On Reset
Watchdog Timer
PWM
AEC-Q100
RoHS
industrial automation
automotive body electronics
HVAC controller
1 / 1