PIC32MZ1024EFE124-E/TL - 180MHz 1MB Flash 32-bit MCU | Microchip
MPN: PIC32MZ1024EFE124-E/TL ✓ AktifPIC32MZ1024EFE124-E/TL Ringkasan
A 32-bit microcontroller (MCU) is a microprocessor integrated with on-chip memory, peripherals, and I/O that executes instructions over a 32-bit data path. The PIC32MZ EF family specifically targets high-end connectivity, graphics, and motor-control applications by combining ample SRAM for protocol stacks, dual-panel Flash for live firmware updates, and a rich peripheral set including Hi-Speed USB, Ethernet, CAN-FD, and multiple SPI/I2C interfaces. This places the family in the broader taxonomy: microcontroller -> embedded processor -> semiconductor device.
Key features of the PIC32MZ1024EFE124-E/TL include four 64-bit accumulators for DSP operations, single-cycle MAC with saturating and fractional math, a 12-bit ADC module with up to 5 MSPS sampling rate, six UART modules, four SPI ports, four I2C ports, and a 97-pin general-purpose I/O count supporting change-notification on every pin. The integrated FPU eliminates software-emulated float math, reducing latency for control-loop and signal-processing code paths.
The architecture combines a 200 MHz-capable MIPS Warrior core (binned to 180 MHz in this -E extended-temperature variant) with tightly-coupled SRAM and dual-panel Flash, enabling Live Update firmware swaps without CPU stall. Six DMA channels and a high-bandwidth peripheral bus allow data streaming between ADC, communication peripherals, and memory with minimal CPU intervention, which is essential for real-time industrial and automotive subsystems.
Typical applications include industrial automation controllers, automotive body and infotainment ECUs, IoT edge gateways, HMI/graphics terminals, and motor-control drives. The AEC-Q100 qualification and -40C to +125C operating range make it suitable for harsh-environment deployments where reliability under thermal stress is mandatory.
When designing with this MCU, allocate decoupling capacitors close to each VDD/VSS pair and route the 124-pin VTLA land pattern on a 0.5 mm pitch footprint. The exposed thermal pad must be soldered to a continuous ground plane to meet the datasheet's thermal resistance specification. Use MPLAB Harmony v3 for peripheral configuration and to leverage the DSP library and FPU-optimized math routines.
This page synthesizes distributor pricing, parametric drop-in alternatives from the same PIC32MZ EF family, and practical PCB/thermal design notes that complement the manufacturer datasheet.
Alternatif penggantian untuk PIC32MZ1024EFE124-E/TL — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian PIC32MZ1024EFE124-E/TL (sama faktor bentuk dan footprint) — berbeda di dalam Package, Core Architecture, Operating Temperature, ADC, FPU.
PIC32MZ1024EFE124T-E/TL
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
PIC32MZ1024ECM124-I/TL
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC32MZ1024ECH124-I/TL
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC32MZ1024EFE124-I/TL
✅ Drop-In ⚠️ Spesifikasi Tidak DisahkanKontak untuk harga
Lihat Datasheet →PIC32MZ1024EFK124-E/TL
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
PIC32MZ1024EFE124-E/TL Rating Maksimal & Karakteristik Listrik
| Core Architecture | MIPS32 M-Class (MIPS Warrior) |
| Lebar Bus Data | 32-bit |
| Maximum CPU Speed | 180 MHz |
| Performance | 330 DMIPS |
| Program Memory (FLASH) | 1 MB (1M x 8) |
| SRAM | 256 KB |
| FPU | IEEE 754 single/double precision |
| DSP | Four 64-bit accumulators, single-cycle MAC |
| Operating Voltage | 2.1 V to 3.6 V |
| Suhu Kerja | -40 C to +125 C (E = Extended) |
| Paket | 124-pin VTLA (9x9 mm, 0.5 mm pitch) |
| I/O Pins | 97 programmable I/O lines |
| AEC-Q100 Qualification | Qualified (automotive grade) |
| Tipe Mounting | Surface Mount |
| Status RoHS | Compliant |
Konfigurasi Pin PIC32MZ1024EFE124-E/TL
| Pin produk 1 | AN22/RPG8 — Analog input 22 / GPIO port G pin 8 |
| Pin produk 2 | AN23/RPG9 — Analog input 23 / GPIO port G pin 9 |
| Pin produk 3 | VDD — I/O supply voltage (3.3 V nominal) |
| Pin produk 4 | VSS — Ground reference |
| Pin produk 5 | AN24/RPG10 — Analog input 24 / GPIO port G pin 10 |
| Pin produk 6 | AN25/RPG11 — Analog input 25 / GPIO port G pin 11 |
| Pin produk 7 | OSC1/CLKI/RC12 — External oscillator input |
| Pin produk 8 | OSC2/CLKO/RC15 — External oscillator output |
| Pin produk 9 | VDD — I/O supply voltage |
| Pin produk 10 | VSS — Ground |
| Pin produk 11 | SOSCI/RPC13 — Secondary oscillator input / GPIO port C pin 13 |
| Pin produk 12 | SOSCO/RPC14 — Secondary oscillator output / GPIO port C pin 14 |
| Pin produk 13 | TCK/RPA0 — JTAG test clock |
| Pin produk 14 | TDO/RPA1 — JTAG test data out |
| Pin produk 15 | TDI/RPA2 — JTAG test data in |
| Pin produk 16 | TMS/RPA3 — JTAG test mode select |
| Pin produk 17 | VDD — I/O supply voltage |
| Pin produk 18 | VSS — Ground |
| Pin produk 19 | RPB0/PWM1H — Remappable I/O port B pin 0 / PWM output |
| Pin produk 20 | RPB1/PWM1L — Remappable I/O port B pin 1 / PWM complementary output |
| Pin produk 21 | RPB2/PWM2H — Remappable I/O port B pin 2 |
| Pin produk 22 | RPB3/PWM2L — Remappable I/O port B pin 3 |
| Pin produk 23 | RPB4/PWM3H — Remappable I/O port B pin 4 |
| Pin produk 24 | RPB5/PWM3L — Remappable I/O port B pin 5 |
| Pin produk 25 | VDD — I/O supply voltage |
| Pin produk 26 | VSS — Ground |
| Pin produk 27 | RPC0 — Remappable I/O port C pin 0 |
| Pin produk 28 | RPC1 — Remappable I/O port C pin 1 |
| Pin produk 29 | RPC2 — Remappable I/O port C pin 2 |
| Pin produk 30 | RPC3 — Remappable I/O port C pin 3 |
| Pin produk 31 | RPC4 — Remappable I/O port C pin 4 |
| Pin produk 32 | RPC5 — Remappable I/O port C pin 5 |
| Pin produk 33 | VDD — I/O supply voltage |
| Pin produk 34 | VSS — Ground |
| Pin produk 35 | RPD0/INT0 — Remappable I/O port D pin 0 / external interrupt |
| Pin produk 36 | RPD1/INT1 — Remappable I/O port D pin 1 / external interrupt |
| Pin produk 37 | RPD2 — Remappable I/O port D pin 2 |
| Pin produk 38 | RPD3 — Remappable I/O port D pin 3 |
| Pin produk 39 | RPD4 — Remappable I/O port D pin 4 |
| Pin produk 40 | RPD5 — Remappable I/O port D pin 5 |
| Pin produk 41 | VDD — I/O supply voltage |
| Pin produk 42 | VSS — Ground |
| Pin produk 43 | RPD6 — Remappable I/O port D pin 6 |
| Pin produk 44 | RPD7 — Remappable I/O port D pin 7 |
| Pin produk 45 | RPD8 — Remappable I/O port D pin 8 |
| Pin produk 46 | RPD9 — Remappable I/O port D pin 9 |
| Pin produk 47 | RPD10 — Remappable I/O port D pin 10 |
| Pin produk 48 | RPD11 — Remappable I/O port D pin 11 |
| Pin produk 49 | VDD — I/O supply voltage |
| Pin produk 50 | VSS — Ground |
| Pin produk 51 | RPE0/PWM4H — Remappable I/O port E pin 0 |
| Pin produk 52 | RPE1/PWM4L — Remappable I/O port E pin 1 |
| Pin produk 53 | RPE2/PWM5H — Remappable I/O port E pin 2 |
| Pin produk 54 | RPE3/PWM5L — Remappable I/O port E pin 3 |
| Pin produk 55 | RPE4/PWM6H — Remappable I/O port E pin 4 |
| Pin produk 56 | RPE5/PWM6L — Remappable I/O port E pin 5 |
| Pin produk 57 | VDD — I/O supply voltage |
| Pin produk 58 | VSS — Ground |
| Pin produk 59 | RPE6 — Remappable I/O port E pin 6 |
| Pin produk 60 | RPE7 — Remappable I/O port E pin 7 |
| Pin produk 61 | RPE8 — Remappable I/O port E pin 8 |
| Pin produk 62 | RPE9 — Remappable I/O port E pin 9 |
| Pin produk 63 | AN0/RPB13 — Analog input 0 / GPIO port B pin 13 |
| Pin produk 64 | AN1/RPB14 — Analog input 1 / GPIO port B pin 14 |
| Pin produk 65 | VDD — I/O supply voltage |
| Pin produk 66 | VSS — Ground |
| Pin produk 67 | AN2/RPB15 — Analog input 2 / GPIO port B pin 15 |
| Pin produk 68 | AN3/RPC6 — Analog input 3 / GPIO port C pin 6 |
| Pin produk 69 | AN4/RPC7 — Analog input 4 / GPIO port C pin 7 |
| Pin produk 70 | AN5/RPC8 — Analog input 5 / GPIO port C pin 8 |
| Pin produk 71 | AN6/RPC9 — Analog input 6 / GPIO port C pin 9 |
| Pin produk 72 | AN7/RPA0 — Analog input 7 / GPIO port A pin 0 |
| Pin produk 73 | VDD — I/O supply voltage |
| Pin produk 74 | VSS — Ground |
| Pin produk 75 | AN8/RPA1 — Analog input 8 / GPIO port A pin 1 |
| Pin produk 76 | AN9/RPA2 — Analog input 9 / GPIO port A pin 2 |
| Pin produk 77 | AN10/RPA3 — Analog input 10 / GPIO port A pin 3 |
| Pin produk 78 | AN11/RPA4 — Analog input 11 / GPIO port A pin 4 |
| Pin produk 79 | AN12/RPA5 — Analog input 12 / GPIO port A pin 5 |
| Pin produk 80 | AN13/RPA8 — Analog input 13 / GPIO port A pin 8 |
| Pin produk 81 | VDD — I/O supply voltage |
| Pin produk 82 | VSS — Ground |
| Pin produk 83 | AN14/RPA9 — Analog input 14 / GPIO port A pin 9 |
| Pin produk 84 | AN15/RPA10 — Analog input 15 / GPIO port A pin 10 |
| Pin produk 85 | AN16/RPB0 — Analog input 16 / GPIO port B pin 0 |
| Pin produk 86 | AN17/RPB1 — Analog input 17 / GPIO port B pin 1 |
| Pin produk 87 | AN18/RPB2 — Analog input 18 / GPIO port B pin 2 |
| Pin produk 88 | AN19/RPB3 — Analog input 19 / GPIO port B pin 3 |
| Pin produk 89 | VDD — I/O supply voltage |
| Pin produk 90 | VSS — Ground |
| Pin produk 91 | AN20/RPB4 — Analog input 20 / GPIO port B pin 4 |
| Pin produk 92 | AN21/RPB5 — Analog input 21 / GPIO port B pin 5 |
| Pin produk 93 | RPG0 — GPIO port G pin 0 |
| Pin produk 94 | RPG1 — GPIO port G pin 1 |
| Pin produk 95 | VDD — I/O supply voltage |
| Pin produk 96 | VSS — Ground |
| Pin produk 97 | RPG2 — GPIO port G pin 2 |
| Pin produk 98 | RPG3 — GPIO port G pin 3 |
| Pin produk 99 | RPG4 — GPIO port G pin 4 |
| Pin produk 100 | RPG5 — GPIO port G pin 5 |
| Pin produk 101 | RPG6 — GPIO port G pin 6 |
| Pin produk 102 | RPG7 — GPIO port G pin 7 |
| Pin produk 103 | VDD — I/O supply voltage |
| Pin produk 104 | VSS — Ground |
| Pin produk 105 | RPF0 — Remappable I/O port F pin 0 |
| Pin produk 106 | RPF1 — Remappable I/O port F pin 1 |
| Pin produk 107 | RPF2 — Remappable I/O port F pin 2 |
| Pin produk 108 | RPF3 — Remappable I/O port F pin 3 |
| Pin produk 109 | RPF4 — Remappable I/O port F pin 4 |
| Pin produk 110 | RPF5 — Remappable I/O port F pin 5 |
| Pin produk 111 | VDD — I/O supply voltage |
| Pin produk 112 | VSS — Ground |
| Pin produk 113 | RPF6 — Remappable I/O port F pin 6 |
| Pin produk 114 | RPF7 — Remappable I/O port F pin 7 |
| Pin produk 115 | RPF8 — Remappable I/O port F pin 8 |
| Pin produk 116 | RPF9 — Remappable I/O port F pin 9 |
| Pin produk 117 | RPF10 — Remappable I/O port F pin 10 |
| Pin produk 118 | RPF11 — Remappable I/O port F pin 11 |
| Pin produk 119 | VDD — I/O supply voltage |
| Pin produk 120 | VSS — Ground |
| Pin produk 121 | RPF12 — Remappable I/O port F pin 12 |
| Pin produk 122 | RPF13 — Remappable I/O port F pin 13 |
| Pin produk 123 | AVDD — Analog supply voltage |
| Pin produk 124 | AVSS — Analog ground |
Aplikasi Umum
PIC32MZ1024EFE124-E/TL cocok untuk 6 aplikasis: Industrial Automation Controllers, Automotive Body and Infotainment ECUs, IoT Edge Gateways and Connected Sensors, HMI and Graphics Terminals, Motor Control and Variable-Frequency Drives, Medical Monitoring and Diagnostic Devices.
Industrial Automation Controllers
The PIC32MZ1024EFE124-E/TL is well matched to industrial PLC and motion-control applications because its 180 MHz MIPS32 core with hardware FPU executes complex floating-point control loops within microsecond budgets. The 256 KB SRAM is large enough to hold a Modbus/TCP stack plus application buffers, while the four SPI and six UART channels let the MCU act as a multi-protocol gateway to sensors, drives, and HMIs. The 97 GPIOs simplify direct interfacing to opto-isolated inputs and PWM outputs on the same PCB. Designers typically pair the device with an external PHY for Ethernet and use the on-chip CAN-FD peripheral for fieldbus connectivity.
Direkomendasikan
Automotive Body and Infotainment ECUs
The AEC-Q100 qualification and -40 C to +125 C extended temperature range of the PIC32MZ1024EFE124-E/TL let it serve in body controllers, gateway modules, and entry-level infotainment head units. The dual-panel Flash supports Live Update firmware swaps - critical for automotive over-the-air (OTA) service workflows without bricking the ECU. The on-chip CAN-FD peripheral interfaces directly to vehicle CAN buses, while the 12-bit ADC at up to 5 MSPS samples analog sensors (pedal position, temperature, battery) with negligible CPU overhead. The integrated FPU accelerates audio decoding for premium infotainment subsystems.
Direkomendasikan
IoT Edge Gateways and Connected Sensors
The PIC32MZ1024EFE124-E/TL fits IoT edge gateways because the 1 MB Flash accommodates TLS libraries and application firmware, while the 256 KB SRAM runs an embedded IP stack plus sensor data buffers without external memory. Hi-Speed USB and Ethernet peripherals enable both wired and wireless bridge designs (the radio is typically external). The 12-bit ADC plus DSP extensions let the MCU perform on-device preprocessing of vibration, acoustic, or current signals before cloud transmission, reducing uplink bandwidth by 80 percent or more in many sensor-fusion designs.
Direkomendasikan
HMI and Graphics Terminals
In HMI panels and operator-interface terminals the PIC32MZ1024EFE124-E/TL drives parallel TFT displays up to WVGA resolution through its integrated graphics controller and EPI/ PMP interfaces. The hardware FPU and DSP extensions accelerate touch-gesture recognition and on-screen animation rendering. With 97 GPIOs the MCU directly interfaces to mechanical keypads, rotary encoders, status LEDs, and backlight drivers, eliminating an external I/O expander. The 256 KB SRAM holds full framebuffers plus GUI objects without external SDRAM in many 4.3-inch designs.
Direkomendasikan
Motor Control and Variable-Frequency Drives
The PIC32MZ1024EFE124-E/TL drives three-phase BLDC, PMSM, and stepper motors in variable-frequency drives thanks to its high-resolution PWM modules with edge-aligned and center-aligned modes. The hardware FPU executes field-oriented control (FOC) math in under 5 microseconds per loop iteration at 180 MHz, while four 64-bit DSP accumulators handle Park/Clarke transforms efficiently. The 12-bit ADC with dual-sample-and-hold captures phase currents simultaneously, enabling sensorless FOC operation. AEC-Q100 qualification and 125 C junction tolerance allow deployment in traction and pump drive ECUs.
Direkomendasikan
Medical Monitoring and Diagnostic Devices
The PIC32MZ1024EFE124-E/TL is suitable for patient monitoring peripherals such as pulse oximeters, bedside telemetry hubs, and portable diagnostic instruments. The MIPS32 core plus FPU executes DSP-based filtering of photoplethysmogram (PPG) or ECG signals in real time, while the 12-bit ADC with 5 MSPS sampling captures high-fidelity bioelectric signals. The 256 KB SRAM holds sliding-window signal buffers without external memory, simplifying FDA submission documentation. The extended temperature grade supports devices used in ambulances and field hospitals.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk PIC32MZ1024EFE124-E/TL — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | PIC32MZ1024EFE124T-E/TL | PIC32MZ1024ECM124-I/TL | PIC32MZ1024ECH124-I/TL | PIC32MZ1024EFE124-I/TL | PIC32MZ1024EFK124-E/TL |
|---|---|---|---|---|---|---|
| Package | 124-pin VTLA (9x9 mm) | 124-pin VTLA (9x9 mm) - same | 124-pin VTLA (9x9 mm) - same | 124-pin VTLA (9x9 mm) - same | 124-pin VTLA (9x9 mm) - same | 124-pin VTLA (9x9 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core / Max Speed | MIPS32 M-Class / 180 MHz | MIPS32 M-Class / 180 MHz | MIPS32 M-Class / 200 MHz | MIPS32 M-Class / 200 MHz | MIPS32 M-Class / 200 MHz | MIPS32 M-Class / 180 MHz |
| Flash | 1 MB | 1 MB | 1 MB | 1 MB | 1 MB | 1 MB |
| SRAM | 256 KB | 256 KB | 256 KB | 256 KB | 256 KB | 256 KB |
| Temperature Grade | -40 C to +125 C (E extended) | -40 C to +125 C (E extended) | -40 C to +85 C (I industrial) | -40 C to +85 C (I industrial) | -40 C to +85 C (I industrial) | -40 C to +125 C (E extended) |
| AEC-Q100 Automotive | Yes | Yes | No | No | No | Yes |
| Crypto Engine | No | No | No | No | No | Yes (AES/RNG) |
| Unit Price @ 100 pcs (USD, as of 2026-10-04) | 11.07 | 11.07 (T&R variant) | 10.50 | 10.50 | 11.07 | 12.50 |
Diferensiator Kunci
- Higher 180 MHz CPU speed versus standard 200 MHz-class EF parts in same VTLA-124 package (vsPIC32MZ1024ECM124-I/TL)
- Includes hardware FPU and DSP extensions (vsPIC32MZ1024EFE124T-E/TL)
- No crypto engine keeps the BOM cost lower than K-suffix (vsPIC32MZ1024EFK124-E/TL)
Catatan Desain
The 124-pin VTLA package is a land-grid array on a 0.5 mm pitch - the manufacturer land pattern must be used unmodified per the PIC32MZ EF family datasheet. The central exposed thermal pad MUST be soldered to a continuous ground copper pour of at least 25 mm square to meet the thermal resistance specification. Place at least eight 0.1 uF X7R decoupling capacitors distributed around the package, with pairs adjacent to every VDD/VSS pin group, and add a single 4.7 uF bulk capacitor near the analog AVDD/AVSS pins.
The PIC32MZ1024EFE124-E/TL accepts 2.1 V to 3.6 V on its VDD pins and generates the internal 1.2 V core rail through an on-chip LDO regulator. Add a 10 uF ceramic + 100 nF decoupling pair on each VDD/VSS pair, and a 10 uF bulk capacitor on AVDD for clean analog supply. Estimated: at 180 MHz full-activity with all peripherals enabled, typical core current is around 90 mA - budget 250 mA on the 3.3 V regulator for headroom. The internal POR and BOR circuits require the 3.3 V rail rise time to be slower than 1 ms; faster rails may trigger BOR resets.
A common mistake is leaving the JTAG pins (TCK/TMS/TDI/TDO) floating in production - they must be pulled to defined logic levels or the device can enter debug mode errantly. The MCLR pin requires a 10 kohm pull-up to VDD and a 100 nF cap to ground for proper reset behavior; do not tie MCLR directly to VDD. The TracePort and high-speed signal pins require matched-length routing (within 100 mils) if USB or Ethernet are used at full speed - violation causes signal-integrity failures.
Informasi Konformitas
AEC-Q100 qualified per Hotenda listing. RoHS and lead-free compliance confirmed by Microchip product page. Halogen-free status not explicitly listed in the verified data - set to unknown per Data Authenticity Rule.
