SN74LS240H - 8-Channel 3-State Inverting Driver | onsemi
MPN: SN74LS240H ✗ Akhir HidupSN74LS240H Ringkasan
An octal buffer or line driver is a digital logic IC that strengthens a signal so it can reliably drive multiple bus loads. The SN74LS240 family combines buffer operation with active-low output enable control, allowing each output to be placed into a high-impedance state when the associated output is not selected. This tri-state capability supports shared buses, bidirectional bus-interface arrangements, and designs that require controlled connection and isolation of multiple logic nodes.
The key functional characteristics are eight inverting channels, a 4.75 V to 5.25 V supply range, three-state outputs, and a 20-pin PDIP package. The three-state outputs are particularly useful in bus-oriented equipment because disabled drivers do not actively contend with another logic source. The H designation identifies a distinct onsemi catalog configuration within the SN74LS240 family, so engineers should confirm ordering details, temperature range, and qualification requirements before release.
The bipolar SN74LS240 architecture belongs to the Low-Power Schottky TTL logic family. Its buffered outputs are intended to improve signal integrity and drive capability when connecting processors, memory devices, peripheral controllers, and bus transceivers. Because the outputs invert, a low input produces a high output and a high input produces a low output when the output driver is enabled. Output-enable polarity must therefore be considered together with data inversion during system-level logic design.
Typical applications include memory address driving, clock and control-line distribution, instrument-bus interfacing, industrial control systems, and legacy computer peripherals. In a shared-bus arrangement, the output-enable signal determines which driver section may actively connect to the bus while the other sections remain in the high-impedance state. In address-driver arrangements, the inverting channels can be assigned according to the required polarity of each memory-control signal.
PCB implementation requires correct DIP pin orientation and adequate routing space around the 20-pin package. Power and ground pins should be connected with short traces and suitable bypass capacitance to limit transient current through package leads. Because outputs can source or sink bus current, external load capacitance, trace length, and simultaneous switching should be checked against the applicable device limits before using the part in high-speed or heavily loaded systems.
This page consolidates the device function, verified catalog information, replacement considerations, and practical implementation guidance. It also distinguishes a genuine pin-compatible replacement from a merely similar logic function and emphasizes that system timing, output-enable polarity, package construction, temperature grade, and qualification requirements must be reviewed together before substitution.
Alternatif penggantian untuk SN74LS240H — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian SN74LS240H (sama faktor bentuk dan footprint) — berbeda di dalam Bits per Element, Logic Type, Number of Elements, Output State.
SN74LS240J
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
SN74LS240N
✅ Drop-InKontak untuk harga
Lihat Datasheet →SN74LS240N
✅ Drop-InKontak untuk harga
Lihat Datasheet →SN74LS240J
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
DM74LS240N
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
MC74LS240N
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
SN74LS240H Rating Maksimal & Karakteristik Listrik
| Number of Channels | 8 channels |
| Supply Voltage Range | 4.75 V to 5.25 V |
| Logic Type | Bipolar inverter |
| Output Function | Inverting |
| Output State | 3-state |
| Number of Elements | 2 elements |
| Bits per Element | 4 bits |
| Package Type | 20-pin PDIP |
| Total Pin Count | 20 pins |
| Tipe Mounting | Through-hole |
SN74LS240H 20-pin pdip Diamant Konfigurasi Panduan
Konfigurasi pin untuk SN74LS240H (20-pin pdip pakai pakai). IC digital ini termasuk GPIO, antarmuka komunikasi (UART, SPI, I2C), dan pin kuasa. Lihat datasheet produsen untuk fungsi pin alternatif dan opsi konfigurasi. Penting untuk desain sistem pengemasan dan PCB.
Tidak ada data diatribut pin yang tersedia untuk SN74LS240H.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
SN74LS240H cocok untuk 6 aplikasis: Memory Address Driving, Shared Digital Bus Interface, Clock and Control Distribution, Industrial Control Systems, Test and Measurement Equipment, Legacy Peripheral Interfacing.
Memory Address Driving
The SN74LS240H is suited to driving memory-address and control lines in systems built around 5 V bipolar logic. Its eight inverting channels provide buffered drive capability, while the grouped output-enable structure can place selected sections into a high-impedance state when those outputs must be disconnected from a shared bus. The 20-pin PDIP package also makes the device straightforward to replace on through-hole legacy boards. Before finalizing the layout, compare address polarity, enable requirements, timing margins, fanout, and trace capacitance against the specific system timing budget. Confirm propagation-delay and output-current limits in the onsemi datasheet because the line-driver function alone does not establish compatibility with every memory timing specification.
Direkomendasikan
Shared Digital Bus Interface
The SN74LS240H can interface a logic subsystem to a shared digital bus when correctly enabled. Its three-state outputs allow disabled drivers to become high-impedance, preventing active contention with another device that owns the bus. The eight inverting channels make it useful for conventional 74LS-style control and data routing, while the 4.75 V to 5.25 V supply range targets nominal 5 V systems. Designers must define every driver-enable state so that no two outputs fight on the same node. PCB trace length, capacitive loading, pull-up or pull-down requirements, and simultaneous switching also require evaluation before the part is approved for a particular bus topology.
Direkomendasikan
Clock and Control Distribution
The SN74LS240H can distribute clock, reset, or control signals when the receiving system requires greater drive strength and controlled disconnect capability. Because the device inverts its inputs, the source signal must be arranged so the receiver sees the intended active or inactive level. Its eight channels can be assigned individually within the device's enable groups, allowing unused outputs to remain isolated. In a clock-distribution design, pay particular attention to edge-rate distortion, unequal trace lengths, capacitive loading, and ground bounce. The onsemi timing table should be used to establish setup and hold margins rather than relying on nominal logic-family behavior alone.
Direkomendasikan
Industrial Control Systems
The SN74LS240H can be used in older industrial-control equipment where 5 V TTL-style signals must drive external logic, relay-interface logic, or a remote bus. The eight inverting three-state channels provide a practical way to strengthen control signals while allowing selected outputs to be disconnected during reset or test modes. Its 20-pin PDIP package is useful for repair and obsolescence-management programs involving through-hole control boards. The design must verify operating-temperature requirements, output current, noise margins, and isolation between connected bus nodes. The device should not be assumed to meet modern industrial qualification requirements without checking the applicable temperature-grade and compliance documentation.
Direkomendasikan
Test and Measurement Equipment
The SN74LS240H is applicable in legacy test and measurement instruments that need to route control signals to front panels, backplanes, or externally accessed logic connectors. Three-state outputs can isolate a group of drivers when an instrument is not actively controlling a line, and the inverting channels can simplify logic inversion in older bench equipment. The through-hole package supports board-level repair and retrofit programs. Designers should assess connector settling time, cable capacitance, ground-return integrity, and possible ground-loop problems. Verify the exact timing and output-drive specifications before using the part with high-speed sampling or precision analog-control circuitry, where additional buffering may be preferable.
Direkomendasikan
Legacy Peripheral Interfacing
The SN74LS240H is well suited to maintaining or repairing legacy peripheral boards that use bipolar 74LS-family inverting drivers. It can connect processor-side signals to printer, storage, display, or expansion-interface logic while retaining the three-state behavior needed by shared bus arrangements. The 20-pin PDIP format supports direct board replacement where pin, function, and electrical requirements match. Replacement work should include a detailed comparison of output-enable polarity, signal inversion, propagation delay, supply current, and temperature range. Review the manufacturer ordering information and markings so that an apparently identical 74LS240 suffix does not introduce an unintended grade or package-material difference.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk SN74LS240H — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | SN74LS240J | SN74LS240N | DM74LS240N | MC74LS240N |
|---|---|---|---|---|---|
| Package | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP |
| Brand | onsemi | onsemi | Texas Instruments | onsemi | onsemi |
| Number of Channels | 8 channels | 8 channels | 8 channels | 8 channels | 8 channels |
| Logic Technology | Bipolar | Bipolar | Bipolar | Bipolar | Bipolar |
| Output Function | Inverting | Inverting | Inverting | Inverting | Inverting |
| Output State | 3-state | 3-state | 3-state | 3-state | 3-state |
| Mounting Type | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole |
| Special Features | Grouped 3-state output enable | Grouped 3-state output enable | Grouped 3-state output enable | Grouped 3-state output enable | Grouped 3-state output enable |
Diferensiator Kunci
- Maintains the complete octal inverting 3-state interface in a through-hole footprint (vsDM74LS240N)
- Uses the same fundamental 74LS240 bus-driver function (vsMC74LS240N)
- Supports grouped output disabling without changing the 20-pin logic footprint (vsSN74LS240J)
Catatan Desain
Mount the DIP with pin 1 oriented toward the component-designator and silk-screen outline, and verify the top-side versus bottom-side insertion orientation. Route the supply and ground pins directly to the nearest suitable bypass capacitor rather than around long data traces. This is especially important for a legacy board because excessive loop length can increase ground bounce during simultaneous output switching.
Keep enabled outputs from simultaneously driving a node shared with another three-state device. Define the enable truth table at the system level and include a startup state that prevents contention. Account for inversion when assigning clock, reset, and address functions. For longer or heavily loaded traces, evaluate edge degradation, bus capacitance, and the output-drive limits stated in the applicable manufacturer datasheet.
Place a ceramic bypass capacitor close to the 5 V supply pin and provide local bulk capacitance where multiple digital devices share the rail. Use a short ground return to the DIP ground pin. The capacitor voltage rating should tolerate supply transients and DC bias effects, while its placement should minimize high-frequency loop area. Confirm the device's recommended operating conditions against the actual rail tolerance.
Do not treat every 74LS240 footprint as an unconditional substitute. Verify the number and polarity of output-enable inputs, the grouping of enabled channels, package construction, temperature grade, qualification status, propagation delay, and load-current limits. Also verify whether the original design expects inverted data. A mechanical fit and matching truth table alone do not prove that timing, noise margin, and environmental requirements are preserved.
Informasi Konformitas
The catalog information does not provide a device-specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration. Compliance must be established from the applicable manufacturer or supplier documentation before procurement.