SN74LS240N - 8-Channel 3-State Buffer | Texas Instruments
MPN: SN74LS240N ✓ AktifSN74LS240N Ringkasan
A three-state buffer is a digital logic device that can present a low level, a high level, or a high-impedance state on its output. The SN74LS240N belongs to the 74LS TTL family, which occupies the logic buffer, line-driver, and bus-interface level of the broader semiconductor hierarchy. Its three-state outputs allow multiple drivers to share a bus when only one group is enabled at a time.
Key characteristics include eight inverting outputs, four output elements, separate output-enable control for the two groups, and operation from a single 4.75 V to 5.25 V supply. The inverting function reverses the logic state presented at each enabled output. The three-state capability is especially useful in memory-address, clock, and bidirectional bus-interface systems where inactive drivers must be isolated rather than continuously switching a node.
The SN74LS240N is a bipolar 74LS-series device rather than a low-power CMOS interface. This places it in applications built around conventional 5 V TTL logic, where system compatibility, established timing behavior, and direct bus interfacing are more important than very low supply current. Its four output elements are organized as two four-bit groups, and each group has a dedicated output-enable input.
Typical uses include three-state bus drivers, memory-address drivers, clock-distribution buffers, industrial control interfaces, test equipment, and legacy computer or peripheral-control systems. Because every output is inverting, the device is appropriate where inverted logic is expected or where an inversion stage can simplify a wider bus arrangement. A non-inverting bus interface may instead require a different 74LS buffer function.
When laying out a board, keep input and output traces short, provide a stable ground reference, and avoid forcing a three-state output into a logic-high or logic-low state while its driver is disabled. Confirm that enable polarity, propagation delay, fanout, and bus contention requirements fit the surrounding system. Use the manufacturer pin-description table when assigning PCB tracks and checking the two output-enable connections.
This product page combines the SN74LS240N function, package, sourcing guidance, verified alternatives, and practical interface considerations. It also provides engineering-focused comparisons for selecting an inverting three-state bus buffer without confusing it with non-inverting or differently controlled 74LS devices.
Alternatif penggantian untuk SN74LS240N — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian SN74LS240N (sama faktor bentuk dan footprint) — berbeda di dalam Bits per Element, Logic Type, Number of Elements, Output State.
DM74LS240N
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
SN74LS240N
✅ Drop-InKontak untuk harga
Lihat Datasheet →SN74LS240N Rating Maksimal & Karakteristik Listrik
| Number of Channels | 8 channels |
| Number of Elements | 2 elements per device |
| Bits per Element | 4 bits per element |
| Logic Type | Inverting buffer and line driver |
| Output State | Three-state output |
| Supply Voltage Range | 4.75 V to 5.25 V |
| Output Enable Inputs | 2 inputs |
| Paket | 20-pin PDIP |
| Tipe Mounting | Through-hole |
| Logic Family | 74LS bipolar TTL |
SN74LS240N 20-pin pdip Diamant Konfigurasi Panduan
Konfigurasi pin untuk SN74LS240N (20-pin pdip pakai pakai). IC digital ini termasuk GPIO, antarmuka komunikasi (UART, SPI, I2C), dan pin kuasa. Lihat datasheet produsen untuk fungsi pin alternatif dan opsi konfigurasi. Penting untuk desain sistem pengemasan dan PCB.
Tidak ada data diatribut pin yang tersedia untuk SN74LS240N.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
SN74LS240N cocok untuk 6 aplikasis: Memory Address Buffering, Three-State Data Bus Interface, Clock Distribution Buffering, Industrial Control Logic Interface, Legacy Peripheral Bus Interface, Test and Measurement Logic.
Memory Address Buffering
The SN74LS240N fits conventional 5 V memory-address systems because it provides eight buffered, inverting outputs in two independently enabled groups of four. Placing one group on an address bus allows the outputs to switch between normal logic and high impedance without holding the bus in a conflicting state. This is useful when several address sources must share a bus, although the inverting behavior must match the memory’s expected address convention. The 4.75 V to 5.25 V operating range aligns with standard 74LS TTL systems. During design, verify enable sequencing, propagation timing, fanout, and the polarity of every address bit before releasing a group onto the shared bus.
Direkomendasikan
Three-State Data Bus Interface
The SN74LS240N is useful in a 5 V three-state bus interface because its eight outputs can become high impedance when their associated enable group is inactive. The two enable inputs permit only one four-bit driver group to operate at a time, reducing bus contention when several devices share a bus. Its buffered outputs support longer PCB routes than an unbuffered logic output, while the inverting action can complement data arriving from a non-inverting source. The designer should still check fanout, rise and fall times, enable setup requirements, and contention timing. High-impedance outputs must not be pulled to an active level by another driver during bus transfer.
Direkomendasikan
Clock Distribution Buffering
The SN74LS240N can distribute a clock signal across eight loads while providing inverting outputs and a high-impedance disable state. The four-output groups permit clock routing to be separated, disabled, or enabled according to the system architecture, and the buffer function helps isolate the source from downstream loading. Because inversion changes clock polarity, downstream sequential logic must be configured for the resulting edge relationship. The 4.75 V to 5.25 V supply range is suitable for 74LS systems, but timing margin, fanout, and skew should be evaluated across every enabled channel. Disable all outputs during the required safe interval whenever a downstream device could otherwise be driven by more than one source.
Direkomendasikan
Industrial Control Logic Interface
The SN74LS240N can act as an interface stage in a 4.75 V to 5.25 V industrial control system that retains classic TTL logic. Eight buffered channels provide practical fanout for control, status, or peripheral-interface signals, while the grouped enables allow unused outputs to remain isolated. The bipolar 74LS implementation suits established 5 V control architectures where logic thresholds and timing are already standardized. In a cabinet or industrial controller, route outputs away from long unprotected harness runs and provide suitable interfacing for external signals. Validate the external logic levels, enable defaults during reset, and the effect of inversion on alarms, interlocks, and machine-control sequences before connecting field wiring.
Direkomendasikan
Legacy Peripheral Bus Interface
The SN74LS240N is appropriate for legacy 5 V peripheral systems that require an inverting, three-state octal bus driver. It can isolate an inactive peripheral driver while another device owns the bus, reducing the number of external components needed for bidirectional-style bus arbitration. Its four-output enable arrangement supports grouped bus ownership, and its 20-pin PDIP package is convenient for repair and through-hole industrial boards. However, the SN74LS241N or SN74LS244N should be considered when the original bus expects non-inverting signals. Verify connector pin assignments, reset behavior, signal polarity, and timing against the original equipment schematic before replacing the device.
Direkomendasikan
Test and Measurement Logic
The SN74LS240N can support legacy test equipment by buffering control or address signals and placing unused drivers into the high-impedance state. Its eight channels cover a full byte, while separate four-channel enable control allows a fixture or tester to isolate sections of the interface. The inverting outputs may directly match an existing TTL test architecture, removing an unnecessary inversion stage. For instrumentation, ensure that disabled outputs do not interfere with external programmable devices and that bus ownership changes only during defined control intervals. Confirm operating temperature, power-supply tolerance, and electrical timing against the enclosure environment, since the device is a bipolar 5 V part rather than a modern low-voltage CMOS device.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk SN74LS240N — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | DM74LS240N | SN74LS240N |
|---|---|---|---|
| Brand | Texas Instruments | National Semiconductor | onsemi |
| Package | 20-pin PDIP | DIP-20 | 20-pin PDIP |
| Function | Octal inverting buffer and line driver | 74LS240 octal buffer and line driver | Buffer, inverting, three-state output |
| Output Configuration | Three-state | Three-state | Three-state |
| Number of Channels | 8 channels | 8 channels | 8 channels |
| Mounting Style | Through-hole | Through-hole | Through-hole |
| Number of Pins | 20 pins | 20 pins | 20 pins |
Diferensiator Kunci
- Provides eight inverting three-state outputs in one 20-pin package (vsDM74LS240N)
- Groups the outputs into two independently enabled four-channel sections (vsSN74LS240N)
- Supports conventional 5 V TTL systems (vsDM74LS240N)
Catatan Desain
Never allow two enabled three-state driver groups to control the same bus node at the same time. The SN74LS240N outputs become high impedance only when their associated output-enable function commands that state. Sequence enable and disable controls with non-overlap timing, account for propagation delay, and establish a defined state during reset. This prevents current contention, undefined bus voltage, and damage to connected outputs.
Treat each enabled output as a standard 74LS TTL driver and include the destination input capacitance in the timing budget. Avoid long branches from a shared output node, use a ground reference close to the device, and keep the enable traces short enough to avoid unequal switching arrival times. Because the outputs are inverting, include the inversion in clock-edge and control-signal timing rather than treating the device as a transparent buffer.
Use the Texas Instruments connection diagram to assign all 20 PDIP positions, including supply and ground. Place the device away from high-current switching nodes, route outputs as short as practical, and avoid long stubs in multi-drop bus layouts. When replacing the SN74LS240N on an existing board, verify physical pin orientation and the enable polarity rather than relying only on the 74LS240 family name.
Informasi Konformitas
Compliance attributes were not explicitly identified in the verified product, distributor, or cross-reference results.