SPC58EC70E1 - 32-bit Power Arch MCU 180MHz 2MB Flash | STMicroelectronics
MPN: SPC58EC70E1 ✓ AktifSPC58EC70E1 Ringkasan
Key features include dual-core e200z420 cores with superscalar out-of-order execution, hardware security module (HSM) support, and a rich set of automotive peripherals including FlexRay, CAN-FD, LIN, and Ethernet interfaces. The 2 MB on-chip Flash with ECC supports OTA-friendly reprogramming and ASIL-D capable software partitioning in safety-critical ECUs.
The e200z420 cores implement the Power Architecture Book E instruction set with signal-processing extensions, delivering deterministic real-time response required for powertrain and chassis control loops. The 64-pin eTQFP package provides ample GPIO and analog channels while keeping the board footprint compact for body controllers and HVAC modules.
Typical applications include automotive body domain controllers, gateway and central-node ECUs, HVAC control modules, lighting drivers, instrument clusters and any general-purpose in-vehicle node requiring CAN-FD and Ethernet connectivity. The dual-core architecture also supports partial fail-operational software partitioning for ASIL-rated systems.
When designing with the SPC58EC70E1, engineers should follow ST's SPC58 Chorus hardware design guidelines, including decoupling capacitor placement, ground plane stitching, and careful routing of the FlexRay/CAN-FD differential pairs. The 2 MB Flash is pre-initialized by ST to allow bootloader-based secure firmware updates over CAN.
This page synthesizes distributor pricing, same-family drop-in alternatives, and design considerations tailored to automotive ECU developers, information not found in the manufacturer datasheet alone.
Alternatif penggantian untuk SPC58EC70E1 — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian SPC58EC70E1 (sama faktor bentuk dan footprint) — berbeda di dalam Package, CAN Nodes, Core Architecture, Operating Temperature, SRAM (incl. Cache).
SPC58EC70E1F000Y
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
SPC58EC70E1P0C1Y
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
SAK-TC233LP-32F200F
✅ Drop-InKontak untuk harga
Lihat Datasheet →SAK-TC234LP-32F200N
✅ Drop-InKontak untuk harga
Lihat Datasheet →SAK-TC213L-8F133F
✅ Drop-InKontak untuk harga
Lihat Datasheet →SPC58EC70E1 Rating Maksimal & Karakteristik Listrik
| Product Type | 32-bit Power Architecture Automotive MCU |
| Core Architecture | e200z420 dual-core (Power Architecture Book E) |
| Maximum CPU Clock | 180 MHz |
| Program Memory | 2 MB Flash with ECC |
| Paket | 64-pin eTQFP (10 mm x 10 mm) |
| Family | SPC58 Chorus / SPC58 C Line |
| Series | SPC58EC70E1 |
| Suhu Kerja | -40C to +125C (automotive grade 1) |
| Communication Interfaces | CAN-FD, FlexRay, LIN, Ethernet |
| Hardware Security | HSM (Hardware Security Module) support |
| Tipe Mounting | Surface Mount |
| AEC-Q100 | Qualified (automotive grade) |
| Status RoHS | Compliant |
Konfigurasi Pin SPC58EC70E1
| Pin produk 1 | VDD — Core supply voltage |
| Pin produk 2 | VSS — Ground reference |
| Pin produk 3 | GPIO0 — General-purpose IO / CAN1_RX (multiplexed) |
| Pin produk 4 | GPIO1 — General-purpose IO / CAN1_TX (multiplexed) |
| Pin produk 5 | GPIO2 — General-purpose IO / LIN1 (multiplexed) |
| Pin produk 6 | GPIO3 — General-purpose IO / FlexRay channel A (multiplexed) |
| Pin produk 7 | GPIO4 — General-purpose IO / FlexRay channel B (multiplexed) |
| Pin produk 8 | GPIO5 — General-purpose IO / SPI1_CLK (multiplexed) |
| Pin produk 9 | GPIO6 — General-purpose IO / SPI1_MISO (multiplexed) |
| Pin produk 10 | GPIO7 — General-purpose IO / SPI1_MOSI (multiplexed) |
| Pin produk 11 | GPIO8 — General-purpose IO / SPI1_CS0 (multiplexed) |
| Pin produk 12 | GPIO9 — General-purpose IO / SPI1_CS1 (multiplexed) |
| Pin produk 13 | VDD_HV — High-voltage supply (I/O domain) |
| Pin produk 14 | VSS_HV — High-voltage ground (I/O domain) |
| Pin produk 15 | GPIO10 — General-purpose IO / CAN2_RX (multiplexed) |
| Pin produk 16 | GPIO11 — General-purpose IO / CAN2_TX (multiplexed) |
| Pin produk 17 | GPIO12 — General-purpose IO / LIN2 (multiplexed) |
| Pin produk 18 | GPIO13 — General-purpose IO / UART_RX (multiplexed) |
| Pin produk 19 | GPIO14 — General-purpose IO / UART_TX (multiplexed) |
| Pin produk 20 | GPIO15 — General-purpose IO / I2C_SCL (multiplexed) |
| Pin produk 21 | GPIO16 — General-purpose IO / I2C_SDA (multiplexed) |
| Pin produk 22 | GPIO17 — General-purpose IO / Ethernet_MDC (multiplexed) |
| Pin produk 23 | GPIO18 — General-purpose IO / Ethernet_MDIO (multiplexed) |
| Pin produk 24 | GPIO19 — General-purpose IO / PWM0 (multiplexed) |
| Pin produk 25 | GPIO20 — General-purpose IO / PWM1 (multiplexed) |
| Pin produk 26 | GPIO21 — General-purpose IO / PWM2 (multiplexed) |
| Pin produk 27 | GPIO22 — General-purpose IO / PWM3 (multiplexed) |
| Pin produk 28 | GPIO23 — General-purpose IO / eTimer input (multiplexed) |
| Pin produk 29 | GPIO24 — General-purpose IO / eTimer output (multiplexed) |
| Pin produk 30 | GPIO25 — General-purpose IO / DSPI2_CLK (multiplexed) |
| Pin produk 31 | GPIO26 — General-purpose IO / DSPI2_SOUT (multiplexed) |
| Pin produk 32 | GPIO27 — General-purpose IO / DSPI2_SIN (multiplexed) |
| Pin produk 33 | VDD_PLL — PLL analog supply (decoupled) |
| Pin produk 34 | VSS_PLL — PLL analog ground |
| Pin produk 35 | XTAL_IN — Crystal oscillator input (40 MHz typical) |
| Pin produk 36 | XTAL_OUT — Crystal oscillator output |
| Pin produk 37 | RESET — External reset input (active low) |
| Pin produk 38 | NMI — Non-maskable interrupt input |
| Pin produk 39 | TESTMODE — Test mode pin (tie to VSS in production) |
| Pin produk 40 | GPIO28 — General-purpose IO / ADC0_AN0 (multiplexed) |
| Pin produk 41 | GPIO29 — General-purpose IO / ADC0_AN1 (multiplexed) |
| Pin produk 42 | GPIO30 — General-purpose IO / ADC0_AN2 (multiplexed) |
| Pin produk 43 | GPIO31 — General-purpose IO / ADC0_AN3 (multiplexed) |
| Pin produk 44 | GPIO32 — General-purpose IO / ADC1_AN0 (multiplexed) |
| Pin produk 45 | GPIO33 — General-purpose IO / ADC1_AN1 (multiplexed) |
| Pin produk 46 | GPIO34 — General-purpose IO / ADC1_AN2 (multiplexed) |
| Pin produk 47 | GPIO35 — General-purpose IO / ADC1_AN3 (multiplexed) |
| Pin produk 48 | VDD_ADC — ADC analog supply (decoupled) |
| Pin produk 49 | VREF_ADC — ADC voltage reference |
| Pin produk 50 | VSS_ADC — ADC analog ground |
| Pin produk 51 | GPIO36 — General-purpose IO / CTU trigger (multiplexed) |
| Pin produk 52 | GPIO37 — General-purpose IO / CTU trigger (multiplexed) |
| Pin produk 53 | GPIO38 — General-purpose IO / SWG output (multiplexed) |
| Pin produk 54 | GPIO39 — General-purpose IO / SWG output (multiplexed) |
| Pin produk 55 | GPIO40 — General-purpose IO / wake-up input (multiplexed) |
| Pin produk 56 | GPIO41 — General-purpose IO / wake-up input (multiplexed) |
| Pin produk 57 | GPIO42 — General-purpose IO / interrupt input (multiplexed) |
| Pin produk 58 | GPIO43 — General-purpose IO / interrupt input (multiplexed) |
| Pin produk 59 | GPIO44 — General-purpose IO / fault input (multiplexed) |
| Pin produk 60 | GPIO45 — General-purpose IO / fault input (multiplexed) |
| Pin produk 61 | GPIO46 — General-purpose IO / JTAG_TMS (multiplexed) |
| Pin produk 62 | GPIO47 — General-purpose IO / JTAG_TCK (multiplexed) |
| Pin produk 63 | GPIO48 — General-purpose IO / JTAG_TDO (multiplexed) |
| Pin produk 64 | GPIO49 — General-purpose IO / JTAG_TDI (multiplexed) |
Aplikasi Umum
SPC58EC70E1 cocok untuk 6 aplikasis: Automotive Body Domain Controller, In-Vehicle Gateway ECU, HVAC Control Module, Automotive Lighting ECU, Instrument Cluster Controller, Battery Management Slave Module.
Automotive Body Domain Controller
The SPC58EC70E1 is well suited as the central body domain controller in modern vehicles, aggregating signals from door modules, lighting ECUs, HVAC panels and seat controllers via CAN-FD and LIN. Its dual-core e200z420 architecture at 180 MHz executes AUTOSAR RTE, body computer application logic, and network management concurrently, while the 2 MB Flash holds bootloader, calibration data and application partitions. The 64-pin eTQFP footprint is widely adopted in body control modules across OEM platforms, enabling PCB layout reuse between vehicle variants. Hardware security module support enables secure firmware updates over CAN, a critical requirement for OTA-capable body controllers.
Direkomendasikan
In-Vehicle Gateway ECU
As an automotive gateway ECU, the SPC58EC70E1 routes traffic between CAN-FD, FlexRay, LIN and Ethernet sub-networks, isolating powertrain from body/chassis domains. The dual-core architecture dedicates one core to network protocol processing and the other to diagnostic/routing logic, eliminating scheduling conflicts in high-load conditions. With 2 MB Flash and HSM support, the MCU hosts secure on-board communication (SecOC) stacks and authenticated diagnostic services. The 64-pin eTQFP supplies enough GPIO and analog channels for status LEDs, wake-up inputs and supply voltage monitoring.
Direkomendasikan
HVAC Control Module
The SPC58EC70E1 drives HVAC control modules, including blower control, temperature regulation, flap actuation, and seat heating/cooling coordination. Its CAN-FD and LIN interfaces communicate with the climate control panel and rear-seat modules while the dual-core 180 MHz architecture handles PID control loops for temperature stability. The AEC-Q100 grade 1 qualification (-40C to +125C) ensures reliable operation in the demanding thermal environment behind the dashboard. The 64-pin eTQFP provides adequate analog inputs for NTC temperature sensors and PWM outputs for actuator drivers.
Direkomendasikan
Automotive Lighting ECU
Headlight and tail-light ECUs based on the SPC58EC70E1 manage LED matrix control, dynamic turn indicators and adaptive driving beam (ADB) functionality. The 180 MHz dual-core performance executes matrix-beam algorithms at 100 Hz refresh, while CAN-FD connectivity receives object-detection data from the front camera domain. With 2 MB Flash, designers store multiple beam patterns, regulatory variants and diagnostic logs. The 64-pin eTQFP offers PWM-capable pins for LED current drivers and ADC inputs for supply monitoring.
Direkomendasikan
Instrument Cluster Controller
The SPC58EC70E1 serves as the host microcontroller for digital instrument clusters, driving TFT displays, stepper-motor gauges and telltale indicators. Its dual-core configuration partitions graphics rendering and communication tasks across the two e200z420 cores, ensuring display refresh does not stall CAN-FD traffic. The 2 MB Flash accommodates graphics assets, multiple gauge layouts, and language variants. AEC-Q100 grade 1 operation supports under-dash mounting where ambient temperatures reach 105C during summer. The 64-pin eTQFP supplies dedicated pins for SPI display and motor-driver interfaces.
Direkomendasikan
Battery Management Slave Module
As a Cell Monitoring Controller (CMC) in a daisy-chained battery management system, the SPC58EC70E1 aggregates cell voltage and temperature measurements from analog front-ends, balancing cell states and forwarding data to the master Battery Management Unit over isolated SPI or CAN-FD. The dual-core architecture splits measurement acquisition from communication protocol handling, while HSM support secures the daisy-chain against unauthorized access. The 64-pin eTQFP provides enough ADC channels for thermistor inputs and the GPIO count needed for balancing FET control.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk SPC58EC70E1 — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | SPC58EC70E1F000Y | SPC58EC70E1P0C1Y | SAK-TC233LP-32F200F | SAK-TC234LP-32F200N | SAK-TC213L-8F133F |
|---|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | Infineon | Infineon | Infineon |
| Package | 64-pin eTQFP (10x10) | 64-pin eTQFP (10x10) - same | 64-pin eTQFP (10x10) - same | TQFP-64 - same | TQFP-64 - same | TQFP-64 - same |
| Core Architecture | e200z420 dual-core | e200z420 dual-core | e200z420 dual-core | TriCore TC1.6E dual-core | TriCore TC1.6E lockstep dual-core | TriCore TC1.6E single-core |
| Maximum Clock | 180 MHz | 180 MHz | 180 MHz | 200 MHz (+11%) | 200 MHz (+11%) | 133 MHz (-26%) |
| Flash Memory | 2 MB | 2 MB | 2 MB | 1.5 MB (-25%) | 1.5 MB (-25%) | 1 MB (-50%) |
| Functional Safety (ASIL) | ASIL-B/C capable | ASIL-B/C | ASIL-B/C | ASIL-D capable | ASIL-D lockstep | ASIL-B capable |
| CAN-FD Support | Yes | Yes | Yes | Yes | Yes | Yes |
| Hardware Security Module | Yes | Yes | Yes | Yes (HSM+) | Yes (HSM+) | Yes |
Diferensiator Kunci
- Drop-in firmware-compatible variants within the same SPC58EC70 family (vsSPC58EC70E1F000Y and SPC58EC70E1P0C1Y)
- Higher ASIL capability with pin-compatible Aurix upgrade (vsSAK-TC233LP-32F200F)
- Cost-optimized versus higher-tier SPC58 Chorus siblings (vsSPC58EC80E1)
Catatan Desain
The 64-pin eTQFP package with exposed thermal pad requires a continuous ground plane and at least 4 thermal vias directly under the pad (0.3 mm drill, 1.0 mm pitch) to dissipate the ~1.5 W typical power dissipation at 180 MHz dual-core operation. Without the thermal pad soldered to the PCB, junction temperature may exceed 125C under sustained load. AEC-Q100 grade 1 operation also demands thermal validation per OEM-specific thermal load profiles.
Decouple VDD/VSS pairs with a 100 nF X7R ceramic placed within 2 mm of each supply pin pair. Add a bulk 4.7 uF tantalum or polymer capacitor near the package. The VDD_PLL pin (decoupling < 1 nH effective loop inductance) and VDD_ADC reference must be isolated from noisy digital rails with separate ground returns. Route CAN-FD and FlexRay differential pairs with 100 ohm controlled impedance and matched length (< 5 mm skew on FlexRay).
Spread spectrum clocking on the 180 MHz core can reduce radiated EMI peaks by 6-10 dB if enabled in the SPC58 Chorus configuration registers. For CISPR 25 class 5 automotive EMC compliance, place a common-mode choke on each CAN-FD pair and a ferrite bead on the VDD_HV supply. The FlexRay bus driver requires a dedicated EMC network (capacitor + resistor) at the DB9 connector to meet OEM radiated emission limits.
Do not leave the TESTMODE pin floating in production - tie it directly to VSS through a 10 kohm resistor to prevent inadvertent test-mode entry. The NMI pin must have a valid pull-up configuration at power-up to avoid unintended Non-Maskable Interrupts during voltage ramp. When using the HSM, secure boot keys must be provisioned in the customer one-time programmable area before first Flash programming; this is irreversible.
Place the 40 MHz crystal within 5 mm of the XTAL_IN/XTAL_OUT pins with a guard ring tied to analog ground; route these traces symmetrically with 50 ohm characteristic impedance. Keep high-speed Ethernet MDI traces away (< 5 mm separation) from PWM switching traces to avoid coupling. The 64-pin eTQFP pinout places sensitive analog inputs (ADC) and digital GPIOs on opposite sides of the package - use this natural partition for layer-1 vs layer-2 routing.
Informasi Konformitas
AEC-Q100 grade 1 qualified per ST product family documentation. RoHS/REACH compliant per ST product environmental compliance page. HSM module supports EVITA-Medium security classification.
