SY88813VKC - 155Mbps PECL Postamplifier | Microchip
MPN: SY88813VKC ✓ AktifSY88813VKC Ringkasan
A limiting postamplifier is a specialized amplifier within the optical communication IC hierarchy. Its primary role is to amplify a small received signal, restore it to a stable digital logic level, and provide a signal-presence indication through the signal-detect function. It sits between the optical receiver or photodiode circuitry and the subsequent digital processing stage, converting a noisy high-frequency analog waveform into a usable PECL output.
The manufacturer describes the SY88813 as a low-power 3.3 V/5 V, 155 Mbps PECL limiting postamplifier. Its principal application is optical networking, where consistent signal detection, compact implementation, and high operating speed are essential. The 10-MSOP package supports surface-mount assembly while keeping the circuit footprint compact enough for communications equipment with dense board layouts.
The SY88813VKC architecture combines signal amplification, limiting, and detection in one device. Limiting is particularly useful in receiver chains because it converts amplitude variations into a controlled digital output, while signal detect provides a hardware indication that the received signal is present. These functions reduce the number of separate operations required immediately after the optical front end.
Typical implementations include SONET or related optical-network receiver cards, 155 Mbps line interfaces, clock-recovery paths, and telecommunications equipment operating from 3.3 V or 5 V supplies. The device is best suited to designs where a compact PECL postamplifier and signal-detect function are needed close to the receiver front end.
PCB implementation should prioritize short high-speed traces, controlled impedance, adequate bypassing, and a solid ground reference. The power and ground connections must follow the manufacturer’s recommended decoupling arrangement, and unused or conditionally used pins should be connected exactly as directed in the pin-description table. Signal routing should minimize discontinuities because the amplifier is intended for data rates up to 155 Mbps.
This page organizes the device identity, verified catalog information, package characteristics, technical alternatives, and application guidance into one engineering reference. It also distinguishes confirmed electrical facts from parameters that require confirmation in the manufacturer datasheet before schematic release or production design.
Alternatif penggantian untuk SY88813VKC — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian SY88813VKC (sama faktor bentuk dan footprint) — berbeda di dalam Maximum Data Rate.
SY88813VKC-TR
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
SY88813VKG
✅ Drop-InKontak untuk harga
Lihat Datasheet →SY88813VKC Rating Maksimal & Karakteristik Listrik
| Product Type | Limiting postamplifier IC |
| Maximum Data Rate | 155 Mbps |
| Supply Voltage Options | 3.3 V or 5 V |
| Output Logic Standard | PECL |
| Signal Detect | PECL signal detect |
| Primary Application | Optical networks |
| Package Type | 10-MSOP |
| Package Dimensions | 3.00 mm width |
| Tipe Mounting | Surface mount |
| Packaging | Tube |
SY88813VKC 3.00 mm width Diamant Konfigurasi Panduan
Konfigurasi pin untuk SY88813VKC (3.00 mm width pakai pakai). Komponen analog ini memiliki pin masukan, keluaran, dan pengirim daya. Lihat datasheet produsen untuk konfigurasi pin offset null, kompensasi, dan pengaktifan. Ideal untuk peralatan sinyal dan kabel penggandaran.
Tidak ada data diatribut pin yang tersedia untuk SY88813VKC.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
SY88813VKC cocok untuk 6 aplikasis: 155 Mbps Optical Receiver, Telecom Line Card, PECL Clock Recovery Path, Optical Network Monitoring, High-Speed Data Interface Conditioning, Optical Receiver Test Fixture.
155 Mbps Optical Receiver
The SY88813VKC fits the receiver chain of a 155 Mbps optical-network interface because it combines low-power limiting amplification with PECL signal detect in a 10-MSOP package. The amplifier can sit after the photodetector and receiver front end, where a small differential waveform must be restored to a stable logic level. Its confirmed 3.3 V or 5 V operation supports conventional telecommunications infrastructure, while the 155 Mbps rating matches the target line rate. Signal detect gives the host circuitry an indication that a valid received signal is present. Board design should preserve controlled impedance and place bypass capacitors close to the supply pins.
Telecom Line Card
A telecom line card can use the SY88813VKC to condition signals arriving from an optical transceiver or receiver module. The 155 Mbps limiting-postamplifier function is appropriate for legacy and installed 155 Mbps transport interfaces, while PECL output supports direct connection to compatible digital logic stages. Its compact 10-MSOP footprint reduces board area compared with a multi-chip limiter and detector implementation. The designer should confirm input common-mode limits, supply current, propagation delay, and signal-detect timing from the manufacturer datasheet before assigning surrounding components and trace lengths.
PECL Clock Recovery Path
The SY88813VKC can provide signal conditioning ahead of clock-recovery circuitry in a 155 Mbps communication system. Limiting converts amplitude variation into a consistent digital waveform, which is useful when the input originates in an optical receiver or a long high-speed interconnect. The integrated PECL signal-detect output can also support loss-of-signal supervision upstream of the recovery block. Because the device operates at rates up to 155 Mbps, layout should use short traces, a continuous return path, and nearby supply bypassing. Confirm the intended topology and interface voltage in the receiver design before layout release.
Optical Network Monitoring
The SY88813VKC is suitable for monitoring a 155 Mbps optical receive path because its PECL signal-detect function reports signal presence while the limiting stage conditions the associated data. A line-card controller can use this indication for link supervision, fault isolation, or alarm processing. The integrated function avoids implementing a separate threshold detector close to the receiver front end. For dependable monitoring, keep the input connection controlled and follow the recommended decoupling arrangement. The signal-detect threshold and response time must be taken directly from the Micrel manufacturer datasheet because those values were not established by the product listing.
High-Speed Data Interface Conditioning
The SY88813VKC can condition a 155 Mbps differential signal in equipment that uses PECL interface levels. Its limiting action provides a stable output amplitude, and the 10-MSOP package permits placement close to the source and destination devices. This makes the part relevant to legacy networking, telecommunications, and test-equipment signal chains where an active limiter is preferable to relying on passive termination alone. Engineering review should verify differential input polarity, output logic levels, operating supply, and timing margins for the specific channel. High-speed routing must avoid long stubs and split supply-return paths.
Optical Receiver Test Fixture
A laboratory fixture for exercising 155 Mbps PECL receiver paths can use the SY88813VKC as the limiting and signal-detection element. The component provides a repeatable way to observe whether an incoming high-speed signal is present while presenting a controlled PECL output to the fixture under test. Its 3.3 V or 5 V flexibility allows use with both legacy and lower-voltage test interfaces. The compact 10-MSOP package simplifies adapter-board construction around the source equipment. Designers should use controlled-impedance coaxial or board traces, provide local bypass capacitance, and consult the manufacturer pin-description table to avoid incorrect differential or signal-detect connections.
Data referensi engineering untuk SY88813VKC — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | SY88813VKC-TR | SY88813VKG |
|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 10-MSOP | 10-MSOP - same | 10-MSOP - same |
| Product Type | Limiting postamplifier IC | Limiting postamplifier IC | PECL postamplifier |
| Maximum Data Rate | 155 Mbps | 155 Mbps | 155 Mbps |
| Supply Voltage | 3.3 V or 5 V | 3.3 V or 5 V | 3.3 V or 5 V |
| Output Logic | PECL | PECL | PECL |
Diferensiator Kunci
- Integrated optical-receiver conditioning (vsSY88813VKG)
- Direct 155 Mbps receiver-path function (vsSY88813VKC-TR)
- Dual 3.3 V and 5 V supply compatibility (vsSY88813VKG)
Catatan Desain
Place the input, output, power, and ground connections according to the manufacturer pin-description and layout guidance. The 10-MSOP footprint is compact, so route the high-speed differential paths as short and symmetric as practical, avoid unnecessary stubs, and maintain a continuous ground reference beneath the device. Verify footprint dimensions and pin numbering against the package drawing before releasing artwork.
Decouple the 3.3 V or 5 V supply close to the device with the capacitance and connection arrangement specified by the Micrel manufacturer datasheet. Keep the decoupling path short and connect it to the same low-impedance ground reference used by the device. A wide supply trace helps reduce voltage droop, while minimizing loop area lowers susceptibility to conversion noise and high-speed transient coupling.
Preserve controlled impedance and adequate return paths for the 155 Mbps differential interface. Avoid routing across plane splits, supplying long test pads on the high-speed nodes, and leaving unmatched stubs in production designs. Validate amplitude, edge rate, jitter, and signal-detect behavior with the actual receiver source and interconnect because the limiter removes amplitude variation but does not correct a poor channel.
Do not substitute SY88813VKC solely because another ordering code uses the same 10-MSOP outline. Confirm differential input polarity, supply sequencing, signal-detect implementation, output levels, and timing from the manufacturer datasheet. Also distinguish the tube-packaged base ordering code from the tape-and-reel ordering code so that the assembly method and incoming inspection plan match the production line.
Informasi Konformitas
The catalog material identifies the device as a Microchip Technology limiting postamplifier for optical networks but does not establish material-compliance or automotive-qualification declarations for the exact order code.