TJA1054AT/VM - 125 kBd CAN Transceiver | NXP Automotive
MPN: TJA1054AT/VM ✓ AktifTJA1054AT/VM Ringkasan
A CAN transceiver is an interface IC within the broader hierarchy of communication interfaces, network semiconductors, and integrated circuits. It converts logic-level signals from a CAN controller into physical bus levels and receives bus signals for presentation to the controller. The TJA1054AT/VM supports legacy CAN systems operating at or below 125 kBd, including applications where bus-node fault tolerance is important.
NXP identifies the TJA1054AT as pin-compatible and downwards-compatible with the PCA82C252T and TJA1053T while retaining all functions. The TJA1054T provides a closely related device in the same product family. This compatibility enables design updates or repair substitutions without changing the PCB land pattern, provided that supply voltage, transceiver mode, bus termination, and software configuration requirements are checked against the detailed NXP documentation.
The fault-tolerant architecture is the central technical feature of the TJA1054 family. Compared with ordinary CAN transceivers, fault-tolerant implementations add behavior intended to continue communication when one bus line is shorted to ground, shorted to the supply, or disconnected. Exact fault-detection limits, recovery behavior, and loopback behavior must be confirmed from the NXP TJA1054 datasheet before setting system test expectations.
Typical uses include passenger-car body-control modules, low-speed CAN gateways, electronic control units, vehicle comfort systems, diagnostic interfaces, and industrial equipment that retains an automotive CAN network. A 125 kBd data rate is appropriate for low-bandwidth control and status traffic rather than high-speed vehicle backbone or payload-oriented industrial CAN networks.
PCB implementation should preserve short, symmetric CANH and CANL routes, a common ground reference, correct 120-ohm bus termination at each physical network end, and protection suitable for the vehicle environment. Because TJA1054AT/VM is the ESD-improved member of the TJA1054 family, designers should still apply appropriate external bus protection where the installation exposes connectors to severe transients.
This product page combines the NXP compatibility statement, package identification, CAN data-rate information, verified replacement candidates, and practical PCB guidance. It also separates confirmed electrical details from parameters that require consultation of the manufacturer datasheet, helping engineers make a defensible sourcing and design decision without relying on unsupported assumptions.
Alternatif penggantian untuk TJA1054AT/VM — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian TJA1054AT/VM (sama faktor bentuk dan footprint) — berbeda di dalam Package, Mounting Type, Product Type.
TJA1054T/N1
✅ Drop-InKontak untuk harga
Lihat Datasheet →PCA82C252T
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
TJA1053T/N1
✅ Drop-InKontak untuk harga
Lihat Datasheet →TJA1054AT/VM Spesifikasi
| Product Type | Fault-tolerant CAN transceiver |
| CAN Data Rate | Up to 125 kBd |
| Bus Interface | CANH and CANL differential bus |
| ESD Protection | ESD-improved TJA1054 version |
| Paket | 14-pin SO package |
| Jumlah Pin | 14 pins |
| Tipe Mounting | Surface-mount SO package |
TJA1054AT/VM 14-pin so package Diamant Konfigurasi Panduan
Konfigurasi pin untuk TJA1054AT/VM (14-pin so package pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.
Tidak ada data diatribut pin yang tersedia untuk TJA1054AT/VM.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
TJA1054AT/VM cocok untuk 6 aplikasis: Passenger-Car Body Control, Low-Speed Vehicle CAN Gateway, Electronic Control Unit CAN Interface, Vehicle Comfort and Access System, Legacy CAN Test and Diagnostic Adapter, Industrial Equipment with Automotive CAN.
Passenger-Car Body Control
The TJA1054AT/VM fits low-speed passenger-car body-control networks that operate at up to 125 kBd. NXP identifies the device as a fault-tolerant CAN transceiver intended primarily for passenger cars, making it appropriate for modules exchanging door, lighting, climate, seat, and body-status commands. Its CANH and CANL interface connects a CAN controller to the physical bus while its fault-tolerant behavior helps maintain communication under specified line faults. The 14-pin SO package supports compact, surface-mounted automotive electronics designs, although the precise supply voltage and mode settings must follow the NXP TJA1054 datasheet. Automotive qualification, transient protection, and exact diagnostic requirements remain system-level verification items.
Direkomendasikan
Low-Speed Vehicle CAN Gateway
TJA1054AT/VM can serve as the physical CAN interface within a gateway that translates between a low-speed vehicle network and another controller or network segment. Its confirmed rate of up to 125 kBd suits supervisory and control traffic rather than bulk data transfer. The fault-tolerant CANH and CANL interface is valuable where the vehicle harness may experience an open circuit or a line-to-ground or line-to-supply fault. Because the device is the ESD-improved AT version, it is a logical selection for modules with exposed vehicle wiring. The gateway designer must still verify bus segmentation, termination placement, transceiver mode, and fault-recovery timing against the manufacturer documentation.
Direkomendasikan
Electronic Control Unit CAN Interface
The TJA1054AT/VM provides an ECU with a fault-tolerant physical interface for legacy CAN communication up to 125 kBd. It is suitable for low-bandwidth control loops, status reporting, and command exchange where the bus must continue operating under specified wiring faults. NXP's compatibility statement shows that the AT family can replace PCA82C252T and TJA1053T designs with retention of all functions, supporting lifecycle management for established passenger-car platforms. In an ECU, place the transceiver close to the connector and protected CAN routing, maintain a low-impedance return path, and follow the recommended termination scheme. Verify operating-mode requirements and supply sequencing before final schematic release.
Direkomendasikan
Vehicle Comfort and Access System
TJA1054AT/VM is appropriate for CAN-connected comfort and access modules such as door, window, seat, climate, and locking controllers. These systems typically exchange compact commands and status data over low-speed CAN rather than transfer high-bandwidth payloads. The device's 125 kBd maximum and fault-tolerant bus interface align with NXP's intended passenger-car use. The AT designation adds an ESD-improvement benefit for interfaces connected to vehicle wiring harnesses, although board-level surge and ESD protection may still be required according to the applicable system specification. Use short, symmetric bus traces and verify that the selected operating mode matches the ECU's standby and wake requirements.
Direkomendasikan
Legacy CAN Test and Diagnostic Adapter
TJA1054AT/VM can form the physical bus side of a diagnostic or test adapter for legacy 125 kBd CAN networks. Its fault-tolerant behavior can help the adapter distinguish network conditions and continue communicating through specified wiring faults, while the 14-pin SO package simplifies integration into compact interface hardware. NXP confirms downward compatibility with the PCA82C252T and TJA1053T, making the part useful when maintaining equipment built around those legacy controllers. Test-adapter developers should confirm the device's diagnostic and loopback modes, configure the controller for the intended bit rate, and account for reversed or absent termination. Supply and I/O levels must be checked from the manufacturer datasheet before connecting it to older test equipment.
Direkomendasikan
Industrial Equipment with Automotive CAN
TJA1054AT/VM can be used in industrial equipment that retains a passenger-car-derived low-speed CAN interface for service functions, diagnostics, or supervisory control. The confirmed 125 kBd limit is appropriate for configuration, status, and alarm traffic but not high-throughput industrial data. The fault-tolerant CANH and CANL interface provides value where field wiring can develop opens or shorts, while the ESD-improved AT construction is useful near external connectors. Engineering validation should include isolation strategy, common-mode limits, termination, grounding, and the precise fault states supported by the device. Since the intended origin is passenger-car electronics, industrial system designers must also assess environmental qualification and protection requirements independently.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk TJA1054AT/VM — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | TJA1054T | PCA82C252T | TJA1053T |
|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | SO14 | SO14 | SO14 | SO14 |
| Product Type | Fault-tolerant CAN transceiver | Fault-tolerant CAN transceiver | CAN transceiver | CAN transceiver |
| Maximum CAN Data Rate | 125 kBd | 125 kBd | 125 kBd | 125 kBd |
| NXP Downward-Compatible Position | Replacement for PCA82C252T and TJA1053T with all functions retained | Replacement for PCA82C252T and TJA1053T with all functions retained | Legacy device replaced by TJA1054AT and TJA1054T | Legacy device replaced by TJA1054AT and TJA1054T |
Diferensiator Kunci
- ESD-improved AT-family positioning (vsTJA1054T)
- Function-retaining migration from a legacy interface (vsPCA82C252T)
- Direct downward compatibility with an established TJA device (vsTJA1053T)
Catatan Desain
Route CANH and CANL as a closely coupled differential pair, with continuous return-current reference over the same board region. Keep the transceiver close to the external CAN connector, keep both bus traces short, and avoid forcing the pair through unrelated switching nodes. This minimizes added loop area and reduces susceptibility to radiated and conducted interference in vehicle electrical environments.
Install nominal 120-ohm termination only at the two physical ends of the CAN network. Removing the transceiver from a powered bus can change the effective termination and disturb signal integrity. Also verify the operating mode, supply timing, ground reference, and controller-side logic levels from the NXP TJA1054 datasheet before connecting a replacement to an established passenger-car network.
Place protection components at the connector boundary and keep their return current close to the CAN interface ground. Review the protection network against the required automotive transient and ESD levels; the AT version is ESD improved, but it does not remove the need for a complete external protection strategy. Validate common-mode range, bus fault recovery, and radiated-emissions behavior with the final wiring harness and enclosure.
Informasi Konformitas
The manufacturer information identifies a passenger-car application but does not explicitly state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status in the referenced records.