NXP Semiconductors

TJA1054AT/VM - 125 kBd CAN Transceiver | NXP Automotive

MPN: TJA1054AT/VM ✓ Active
14-pin SO package Package
MOQ: 1 |

TJA1054AT/VM Overview

NXP TJA1054AT/VM is a fault-tolerant CAN transceiver for low-speed Controller Area Network communication up to 125 kBd, presented in a 14-pin SO package. The device provides the physical interface between a CAN protocol controller and the CAN bus wiring while adding ESD protection to the original TJA1054 function. It is primarily intended for passenger-car systems where low-speed CAN networks connect electronic control units and body electronics.

A CAN transceiver is an interface IC within the broader hierarchy of communication interfaces, network semiconductors, and integrated circuits. It converts logic-level signals from a CAN controller into physical bus levels and receives bus signals for presentation to the controller. The TJA1054AT/VM supports legacy CAN systems operating at or below 125 kBd, including applications where bus-node fault tolerance is important.

NXP identifies the TJA1054AT as pin-compatible and downwards-compatible with the PCA82C252T and TJA1053T while retaining all functions. The TJA1054T provides a closely related device in the same product family. This compatibility enables design updates or repair substitutions without changing the PCB land pattern, provided that supply voltage, transceiver mode, bus termination, and software configuration requirements are checked against the detailed NXP documentation.

The fault-tolerant architecture is the central technical feature of the TJA1054 family. Compared with ordinary CAN transceivers, fault-tolerant implementations add behavior intended to continue communication when one bus line is shorted to ground, shorted to the supply, or disconnected. Exact fault-detection limits, recovery behavior, and loopback behavior must be confirmed from the NXP TJA1054 datasheet before setting system test expectations.

Typical uses include passenger-car body-control modules, low-speed CAN gateways, electronic control units, vehicle comfort systems, diagnostic interfaces, and industrial equipment that retains an automotive CAN network. A 125 kBd data rate is appropriate for low-bandwidth control and status traffic rather than high-speed vehicle backbone or payload-oriented industrial CAN networks.

PCB implementation should preserve short, symmetric CANH and CANL routes, a common ground reference, correct 120-ohm bus termination at each physical network end, and protection suitable for the vehicle environment. Because TJA1054AT/VM is the ESD-improved member of the TJA1054 family, designers should still apply appropriate external bus protection where the installation exposes connectors to severe transients.

This product page combines the NXP compatibility statement, package identification, CAN data-rate information, verified replacement candidates, and practical PCB guidance. It also separates confirmed electrical details from parameters that require consultation of the manufacturer datasheet, helping engineers make a defensible sourcing and design decision without relying on unsupported assumptions.

Drop-in alternatives for TJA1054AT/VM — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

Variants in this series

Same-series models that are drop-in compatible with TJA1054AT/VM (same form factor and footprint) — differing in Package, Mounting Type, Product Type.

NXP Semiconductors
Package: 14-SO
Mounting Type: Surface mount
Product Type: Half CANbus transceiver
NXP Semiconductors
Package: 14-pin SOIC, 3.9 mm body
Mounting Type: Surface mount

TJA1054T/N1

✅ Drop-In
NXP Semiconductors
📦 SO14
Fault-tolerant CAN transceiver · 125 kBd · Low-speed passenger-car CAN networks · CANH and CANL differential bus · 14-pin SOIC, 3.9 mm body · Surface mount · Between CAN protocol controller and physical bus wires · Fault-tolerant CAN operation

Contact for price

View Datasheet →

PCA82C252T

✅ Drop-In
📦 SO14
0 kBd difference for the intended 125 kBd application; TJA1054AT adds the AT ESD-improvement positioning and retains all legacy functions

📋 Reference alternative (not in catalog)

TJA1053T/N1

✅ Drop-In
NXP Semiconductors
📦 SO14
Half CANbus transceiver · 1 transmit / 1 receive · 4.75 V to 5.25 V · 5 V · Up to 36 V · Controller Area Network (CAN) · 14-SO · 14 pins

Contact for price

View Datasheet →

TJA1054AT/VM Specifications

Product Type Fault-tolerant CAN transceiver
CAN Data Rate Up to 125 kBd
Bus Interface CANH and CANL differential bus
ESD Protection ESD-improved TJA1054 version
Package 14-pin SO package
Pin Count 14 pins
Mounting Type Surface-mount SO package

TJA1054AT/VM 14-pin so package Pin Configuration Guide

Pin configuration for TJA1054AT/VM (14-pin so package package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.

14-pin so package package pinout diagram for TJA1054AT/VM

No detailed pinout data available for TJA1054AT/VM.

Refer to the datasheet for full pin configuration.

Typical Applications

TJA1054AT/VM is suitable for 6 applications: Passenger-Car Body Control, Low-Speed Vehicle CAN Gateway, Electronic Control Unit CAN Interface, Vehicle Comfort and Access System, Legacy CAN Test and Diagnostic Adapter, Industrial Equipment with Automotive CAN.

🚗

Passenger-Car Body Control

The TJA1054AT/VM fits low-speed passenger-car body-control networks that operate at up to 125 kBd. NXP identifies the device as a fault-tolerant CAN transceiver intended primarily for passenger cars, making it appropriate for modules exchanging door, lighting, climate, seat, and body-status commands. Its CANH and CANL interface connects a CAN controller to the physical bus while its fault-tolerant behavior helps maintain communication under specified line faults. The 14-pin SO package supports compact, surface-mounted automotive electronics designs, although the precise supply voltage and mode settings must follow the NXP TJA1054 datasheet. Automotive qualification, transient protection, and exact diagnostic requirements remain system-level verification items.

🚗

Low-Speed Vehicle CAN Gateway

TJA1054AT/VM can serve as the physical CAN interface within a gateway that translates between a low-speed vehicle network and another controller or network segment. Its confirmed rate of up to 125 kBd suits supervisory and control traffic rather than bulk data transfer. The fault-tolerant CANH and CANL interface is valuable where the vehicle harness may experience an open circuit or a line-to-ground or line-to-supply fault. Because the device is the ESD-improved AT version, it is a logical selection for modules with exposed vehicle wiring. The gateway designer must still verify bus segmentation, termination placement, transceiver mode, and fault-recovery timing against the manufacturer documentation.

🏭

Electronic Control Unit CAN Interface

The TJA1054AT/VM provides an ECU with a fault-tolerant physical interface for legacy CAN communication up to 125 kBd. It is suitable for low-bandwidth control loops, status reporting, and command exchange where the bus must continue operating under specified wiring faults. NXP's compatibility statement shows that the AT family can replace PCA82C252T and TJA1053T designs with retention of all functions, supporting lifecycle management for established passenger-car platforms. In an ECU, place the transceiver close to the connector and protected CAN routing, maintain a low-impedance return path, and follow the recommended termination scheme. Verify operating-mode requirements and supply sequencing before final schematic release.

🚗

Vehicle Comfort and Access System

TJA1054AT/VM is appropriate for CAN-connected comfort and access modules such as door, window, seat, climate, and locking controllers. These systems typically exchange compact commands and status data over low-speed CAN rather than transfer high-bandwidth payloads. The device's 125 kBd maximum and fault-tolerant bus interface align with NXP's intended passenger-car use. The AT designation adds an ESD-improvement benefit for interfaces connected to vehicle wiring harnesses, although board-level surge and ESD protection may still be required according to the applicable system specification. Use short, symmetric bus traces and verify that the selected operating mode matches the ECU's standby and wake requirements.

🔧

Legacy CAN Test and Diagnostic Adapter

TJA1054AT/VM can form the physical bus side of a diagnostic or test adapter for legacy 125 kBd CAN networks. Its fault-tolerant behavior can help the adapter distinguish network conditions and continue communicating through specified wiring faults, while the 14-pin SO package simplifies integration into compact interface hardware. NXP confirms downward compatibility with the PCA82C252T and TJA1053T, making the part useful when maintaining equipment built around those legacy controllers. Test-adapter developers should confirm the device's diagnostic and loopback modes, configure the controller for the intended bit rate, and account for reversed or absent termination. Supply and I/O levels must be checked from the manufacturer datasheet before connecting it to older test equipment.

🏭

Industrial Equipment with Automotive CAN

TJA1054AT/VM can be used in industrial equipment that retains a passenger-car-derived low-speed CAN interface for service functions, diagnostics, or supervisory control. The confirmed 125 kBd limit is appropriate for configuration, status, and alarm traffic but not high-throughput industrial data. The fault-tolerant CANH and CANL interface provides value where field wiring can develop opens or shorts, while the ESD-improved AT construction is useful near external connectors. Engineering validation should include isolation strategy, common-mode limits, termination, grounding, and the precise fault states supported by the device. Since the intended origin is passenger-car electronics, industrial system designers must also assess environmental qualification and protection requirements independently.

Recommended Products Summary

TJA1054T Pin-compatible related CAN transceiver Used in: Passenger-Car Body Control, Low-Speed Vehicle CAN Gateway, Vehicle Comfort and Access System, Legacy CAN Test and Diagnostic Adapter, Industrial Equipment with Automotive CAN TJA1053T Function-retaining downward-compatible CAN device Used in: Passenger-Car Body Control, Electronic Control Unit CAN Interface, Vehicle Comfort and Access System, Industrial Equipment with Automotive CAN PCA82C252T Function-retaining legacy CAN transceiver Used in: Low-Speed Vehicle CAN Gateway, Electronic Control Unit CAN Interface, Legacy CAN Test and Diagnostic Adapter, Industrial Equipment with Automotive CAN
What is TJA1054AT/VM?
TJA1054AT/VM is an NXP fault-tolerant, ESD-improved CAN transceiver for low-speed Controller Area Network communication up to 125 kBd. According to the NXP TJA1054 datasheet, the device interfaces a CAN protocol controller with the physical CANH and CANL bus conductors and is packaged in a 14-pin SO package. Its primary target is passenger-car electronics using legacy low-speed CAN networks.
What is the operating data rate of TJA1054AT/VM?
The TJA1054AT/VM supports CAN communication up to 125 kBd. This rate makes the transceiver appropriate for low-speed passenger-car control and status networks rather than high-speed CAN backbones. The NXP TJA1054 datasheet describes the device as being intended primarily for low-speed applications up to 125 kBd, and system timing should be checked against that limit.
Is TJA1054AT/VM a drop-in replacement for TJA1054T?
TJA1054AT/VM can be considered for replacement of TJA1054T where the PCB footprint and required functions match. NXP states that the TJA1054AT is, like the TJA1054T, pin-compatible and downwards-compatible with the PCA82C252T and TJA1053T. Before substitution, verify the exact SO-package ordering code, supply voltage, operating mode, and any functional distinctions in the detailed NXP documentation.
Which devices can replace PCA82C252T and TJA1053T?
NXP identifies TJA1054AT and TJA1054T as replacements for the PCA82C252T and TJA1053T with retention of all functions. The manufacturer explicitly describes the devices as pin-compatible and downwards-compatible. This statement supports PCB reuse, but the engineer should still confirm package orientation, electrical operating limits, transceiver-mode requirements, and bus fault behavior before approving a production substitution.
What is the difference between TJA1054AT/VM and TJA1054T?
TJA1054AT/VM is the ESD-improved TJA1054AT ordering variant, while TJA1054T is the closely related base-family device. The NXP product information states that both are pin-compatible and downwards-compatible with the PCA82C252T and TJA1053T. Because the supplied manufacturer material does not quantify every electrical difference, use the full NXP ordering table and datasheet to confirm mode, supply, and immunity requirements.
Where can I download the TJA1054AT datasheet PDF?
The official TJA1054 datasheet PDF is available from the NXP document link listed on this page. It should be the primary document for electrical characteristics, truth tables, fault-mode behavior, limiting values, application information, and package drawings. The TJA1054AT/VM ordering suffix identifies the 14-pin SO delivery variant, so verify that the document revision covers the selected suffix.
Where can I find the TJA1054AT/VM pinout?
The TJA1054AT/VM pinout and package drawing are defined in the NXP TJA1054 datasheet. The distributor records identify the device as a 14-pin SO CAN transceiver. Use the pin-description table in the manufacturer datasheet when assigning CANH, CANL, ground, supply, controller-interface, mode, and enable connections; do not infer pin functions solely from connector or board-layout appearance.
Is TJA1054AT/VM suitable for automotive passenger-car systems?
TJA1054AT/VM is suitable for low-speed automotive passenger-car CAN networks. The NXP product description identifies low-speed applications up to 125 kBd in passenger cars, while the fault-tolerant architecture supports operation during specified bus-line fault conditions. Suitability for a particular vehicle also depends on the required CAN version, network topology, transient environment, diagnostic behavior, and qualification requirements.
What can replace TJA1054AT/VM?
TJA1054T, PCA82C252T, and TJA1053T are the confirmed replacement candidates identified by NXP compatibility information. These devices retain the documented functions when used in the applicable downward-compatible designs and share the relevant pin arrangement. The TJA1054AT/S900VM order code should not be treated as an engineering alternative because it is a supplier-specific ordering variant.
Is there a verified cross-brand drop-in equivalent for TJA1054AT/VM?
No cross-brand drop-in equivalent is established by the manufacturer and cross-reference records available for TJA1054AT/VM. The confirmed candidates are from NXP-compatible legacy CAN devices, so an unverified third-party part should not be assumed to be pin-to-pin, fault-behavior compatible, or electrically interchangeable. Use the Request a Quote form when requesting sourcing help and provide the required SO-package and electrical constraints.
When should I choose TJA1054AT/VM over TJA1054T?
Choose TJA1054AT/VM when the design benefits from the AT version's ESD-improvement positioning while retaining the TJA1054 family behavior. Choose TJA1054T when an established base-family design does not require that variant and its operating conditions are fully documented for the application. NXP confirms that the two are pin-compatible and downwards-compatible with PCA82C252T and TJA1053T.
Can TJA1054AT/VM replace PCA82C252T without PCB changes?
TJA1054AT/VM can replace PCA82C252T without a PCB change when the package, pin functions, and required operating conditions match the original design. NXP explicitly states that the TJA1054AT and TJA1054T are pin-compatible and downwards-compatible with the PCA82C252T and retain all functions. A production change should still include a hardware regression check for bus termination, mode settings, and fault recovery.
What are the key specifications of TJA1054AT/VM that engineers should know?
The key confirmed specifications of TJA1054AT/VM are fault-tolerant CAN operation, a maximum stated data rate of 125 kBd, ESD-improved construction, and a 14-pin SO package. It interfaces a CAN controller with CANH and CANL. The device is intended primarily for low-speed passenger-car systems and is pin-compatible with PCA82C252T and TJA1053T according to NXP.
Is TJA1054AT/VM in stock, and what is the lead time?
Current stock and lead time should be confirmed through the Request a Quote form on this page. The manufacturer product page and distributor records identify TJA1054AT/VM, but a live distributor search result alone does not guarantee a committed quantity or delivery schedule. Include the required quantity, target package suffix, date code preference, and production schedule with the request.
Where can I buy TJA1054AT/VM and what is its price?
TJA1054AT/VM can be requested through the Request a Quote form on this page for current commercial availability and pricing. The official ordering designation is TJA1054AT/VM, with some distributor records using TJA1054AT/VM,512 to indicate the reel quantity. Provide the exact required suffix, quantity, and delivery target when requesting a quotation.

Engineering reference data for TJA1054AT/VM — comparison, design guidance, and compliance information.

Selection Guide

Choose TJA1054AT/VM for a new or maintained low-speed passenger-car CAN design that benefits from the AT version's ESD-improvement positioning and needs fault-tolerant physical-bus behavior. Choose TJA1054T when the base TJA1054 device is already established in the target design and the complete electrical requirements are documented. Choose PCA82C252T or TJA1053T when maintaining an existing legacy design whose functions and operating conditions have already been validated, although new designs generally favor the TJA1054AT fault-tolerant position. All three confirmed alternatives use the SO14 footprint and are identified by NXP as downward-compatible with the relevant legacy devices. No cross-brand part is recommended without independent evidence of pin-to-pin compatibility, matching fault behavior, supply limits, timing, and transceiver modes.

Comparison with Alternatives

Parameter This Product TJA1054T PCA82C252T TJA1053T
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors
Package SO14 SO14 SO14 SO14
Product Type Fault-tolerant CAN transceiver Fault-tolerant CAN transceiver CAN transceiver CAN transceiver
Maximum CAN Data Rate 125 kBd 125 kBd 125 kBd 125 kBd
NXP Downward-Compatible Position Replacement for PCA82C252T and TJA1053T with all functions retained Replacement for PCA82C252T and TJA1053T with all functions retained Legacy device replaced by TJA1054AT and TJA1054T Legacy device replaced by TJA1054AT and TJA1054T

Key Differentiators

  • ESD-improved AT-family positioning (vs TJA1054T)
  • Function-retaining migration from a legacy interface (vs PCA82C252T)
  • Direct downward compatibility with an established TJA device (vs TJA1053T)

Design Notes

Route CANH and CANL as a closely coupled differential pair, with continuous return-current reference over the same board region. Keep the transceiver close to the external CAN connector, keep both bus traces short, and avoid forcing the pair through unrelated switching nodes. This minimizes added loop area and reduces susceptibility to radiated and conducted interference in vehicle electrical environments.

Install nominal 120-ohm termination only at the two physical ends of the CAN network. Removing the transceiver from a powered bus can change the effective termination and disturb signal integrity. Also verify the operating mode, supply timing, ground reference, and controller-side logic levels from the NXP TJA1054 datasheet before connecting a replacement to an established passenger-car network.

Place protection components at the connector boundary and keep their return current close to the CAN interface ground. Review the protection network against the required automotive transient and ESD levels; the AT version is ESD improved, but it does not remove the need for a complete external protection strategy. Validate common-mode range, bus fault recovery, and radiated-emissions behavior with the final wiring harness and enclosure.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

The manufacturer information identifies a passenger-car application but does not explicitly state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status in the referenced records.

Related Searches

tja1054at datasheet tja1054at ic datasheet nxp tja1054at TJA1054AT/VM datasheet pdf TJA1054AT/VM pinout TJA1054AT/VM equivalent TJA1054AT/VM replacement TJA1054AT/VM cross reference TJA1054AT vs TJA1054T TJA1054AT SO14 footprint TJA1054AT 125 kBd CAN TJA1054AT fault tolerant CAN TJA1054AT/VM price TJA1054AT/VM stock

Related Components & Terms

NXP Semiconductors TJA1054AT/VM TJA1054AT TJA1054T PCA82C252T TJA1053T Controller Area Network CAN transceiver CAN interface fault-tolerant CAN ESD protection low-speed CAN CANH CANL 125 kBd SO14 SOIC-14 surface-mount package passenger-car electronics vehicle body control electronic control unit CAN bus termination 120-ohm termination low-dropout voltage interface IC
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details