TLV2401ID - 5.5kHz Low-Power RRIO Op Amp | TI
MPN: TLV2401ID ✓ AktifTLV2401ID Ringkasan
An operational amplifier is an analog signal-processing IC that uses high-gain feedback to amplify or buffer a voltage difference between its two inputs. The TLV2401 belongs to the operational-amplifier hierarchy, where rail-to-rail input and output capability helps the amplifier operate across most of the supply range without requiring separate input or output rail restrictions. This makes it useful for sensors and mixed-signal systems whose operating signals can approach either supply rail.
The principal features of the TLV2401ID include a 5.5 kHz gain-bandwidth product, approximately 880 nA per channel of typical bias current, rail-to-rail inputs and outputs, and operation from a single supply up to 16 V. Reverse-battery protection helps protect the amplifier when input polarity is reversed, while the over-the-rail input capability extends usable input behavior beyond the nominal supply rails under the conditions stated by the manufacturer.
Its low gain-bandwidth product favors low-frequency precision and signal-conditioning tasks rather than wideband waveform processing. At relatively low operating frequencies, a closed-loop amplifier built around this device can provide stable gain with straightforward compensation and external feedback networks. The low bias current also reduces the effect of high-value sensor sources, although actual offset, noise, and bias-current behavior must be evaluated for the intended temperature and supply range.
Typical uses include battery-powered sensor interfaces, portable ECG and biomedical signal conditioning, industrial measurement inputs, low-frequency current sensing, and general-purpose analog buffers. The 8-SOIC format supports conventional surface-mount assembly and PCB prototyping, while the single-amplifier configuration allows designers to avoid unnecessary channel count.
Design with the TLV2401ID by placing input, feedback, and bypass components close to the device and verifying common-mode range, output swing, stability, and noise at the intended supply voltage. The Request a Quote form on this page can provide current commercial availability, lead-time, and order information.
This product page combines the Texas Instruments ordering information, manufacturer datasheet characteristics, package details, drop-in family options, and practical design guidance to help engineers evaluate the TLV2401ID for low-power analog signal-conditioning designs.
Alternatif penggantian untuk TLV2401ID — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian TLV2401ID (sama faktor bentuk dan footprint) — berbeda di dalam Package.
TLV2402ID
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan✓ Ada di Gudang
$1.4273 / Satuan
Lihat Datasheet →TLV2403ID
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
TLV2404ID
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
TLV2409ID
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
TLV9101ID
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
TLV2401ID Rating Maksimal & Karakteristik Listrik
| Product Type | Single operational amplifier |
| Amplifier Count | 1 circuit |
| Maximum Supply Voltage | 16 V |
| Gain-Bandwidth Product | 5.5 kHz |
| Typical Bias Current | 880 nA per channel |
| Input Type | Rail-to-rail input |
| Tipe Output | Rail-to-rail output |
| Reverse-Battery Protection | 18 V |
| Over-the-Rail Input Operation | 5 V |
| Typical Specification Supply | 5 V |
| Rentang Suhu Kerja | -40°C to +125°C |
| Paket | 8-SOIC |
| Package Type | Gull-wing surface-mount package |
| Terminal Count | 8 |
| Temperature Grade | Automotive |
| Tipe Mounting | Surface mount |
TLV2401ID gull-wing surface-mount package Diamant Konfigurasi Panduan
Konfigurasi pin untuk TLV2401ID (gull-wing surface-mount package pakai pakai). Komponen analog ini memiliki pin masukan, keluaran, dan pengirim daya. Lihat datasheet produsen untuk konfigurasi pin offset null, kompensasi, dan pengaktifan. Ideal untuk peralatan sinyal dan kabel penggandaran.
Tidak ada data diatribut pin yang tersedia untuk TLV2401ID.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
TLV2401ID cocok untuk 6 aplikasis: Battery-Powered Sensor Interface, Portable Biomedical Signal Conditioning, Industrial Process Measurement, Low-Frequency Current Sensing, Portable Data Acquisition, General-Purpose Analog Buffer.
Battery-Powered Sensor Interface
The TLV2401ID fits low-frequency sensor interfaces because its typical bias current is 880 nA per channel and its rail-to-rail input stage can accept signals near the supply rails. Place the amplifier in a noninverting or transimpedance configuration around the sensor, with the feedback network selected for the required gain and sensor impedance. The 5.5 kHz gain-bandwidth product favors slow-changing measurements rather than fast pulses. Its 16 V maximum supply rating also permits compatibility with higher-voltage single-supply systems, although the selected operating voltage must remain within the manufacturer’s limits. A key design trade-off is that low bandwidth improves power economy but limits closed-loop response and slew capability.
Direkomendasikan
Portable Biomedical Signal Conditioning
The TLV2401ID is useful for conditioning low-amplitude, low-frequency physiological signals where low amplifier bias current helps preserve high source impedance. Its 880 nA per-channel typical bias current is especially relevant when the input source presents substantial resistance, while rail-to-rail input and output operation supports single-supply signal paths. The 5.5 kHz gain-bandwidth product is appropriate for heartbeat, pressure, or temperature waveforms in the low-frequency range. Designers should still evaluate noise, offset, input protection, patient-safety isolation, and electrode-driven transient limits. These protections must be implemented at the system level and confirmed against the device absolute-maximum ratings.
Direkomendasikan
Industrial Process Measurement
The TLV2401ID can amplify low-level signals from resistive bridges, temperature elements, and other slow-changing industrial sensors because it combines rail-to-rail operation with a typical bias current of 880 nA per channel. Place it close to the sensor to minimize susceptible trace length, and use the amplifier’s gain-bandwidth product to set the usable signal bandwidth. A 5.5 kHz device is appropriate for temperature, pressure, and level channels that do not require wideband transient response. In factory equipment, reverse-battery and over-the-rail input features provide additional robustness, but the design must still include appropriate surge and ESD protection at the connector. Power-supply grounding and sensor-return routing remain critical to useful measurement accuracy.
Direkomendasikan
Low-Frequency Current Sensing
The TLV2401ID is appropriate for amplifying the small voltage produced by a shunt in low-frequency current measurements when the design prioritizes low power and high input impedance. The typical 880 nA per-channel bias current reduces loading of the sensed node, and rail-to-rail input and output behavior can simplify operation from a single supply. The 5.5 kHz gain-bandwidth product is suitable for measurements that change slowly relative to the amplifier bandwidth. Layout should keep the high-impedance sense connection short and place the differential pair symmetrically to reduce offset pickup. If the shunt signal requires faster settling or larger output swings, a higher-bandwidth family member may be more appropriate.
Direkomendasikan
Portable Data Acquisition
The TLV2401ID supports portable data-acquisition front ends that sample slowly varying analog channels from sensors while operating from a compact battery-powered supply. Its approximately 880 nA per-channel typical bias current helps preserve weak sensor signals, and the 16 V maximum supply rating offers flexibility for higher-voltage analog rails. The 5.5 kHz gain-bandwidth product is well matched to temperature, pressure, potentiometer, and slow position signals rather than high-rate waveform acquisition. Use a common bypass capacitor strategy, maintain symmetric feedback routing, and verify settling behavior for the selected channel-gain combination. The rail-to-rail stages also help maximize usable signal range in compact systems where supply headroom is limited.
Direkomendasikan
General-Purpose Analog Buffer
The TLV2401ID can serve as a voltage buffer or gain stage for slow analog signals that require rail-to-rail input and output behavior but not high bandwidth. Its 16 V supply capability supports a broader range of industrial and instrumentation rails, while low typical bias current reduces disturbance to high-impedance sources. Use unity-gain or low-gain feedback arrangements when preserving signal range and stability are priorities. The 5.5 kHz bandwidth provides margin for many control, monitoring, and interface signals, but it should be checked against required loop bandwidth and transient response. Place the bypass capacitor near the supply pins and route feedback traces away from noisy inputs to minimize unintended coupling.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk TLV2401ID — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | TLV2402ID | TLV2403ID | TLV2404ID | TLV2409ID | TLV9101ID |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Amplifier Count | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
| Input Type | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Output Type | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
Diferensiator Kunci
- Lower-bandwidth optimization for slow, low-power measurements (vsTLV9101ID)
- Lower documented noise density in the higher-bandwidth comparison (vsTLV9101ID)
- Input and output operation across the supply range (vsTLV2404ID)
- Reverse-battery and over-the-rail input robustness (vsTLV2402ID)
Catatan Desain
Place the bypass capacitor and amplifier input, output, and feedback components close to their associated pins. Keep the feedback loop compact and route it away from the noninverting input to reduce parasitic coupling and oscillation. For a high-impedance source, minimize the sensitive input trace length and maintain symmetric routing around the differential inputs. The manufacturer pin-configuration and package-drawing sections should guide the physical implementation of the 8-SOIC footprint.
Use the 5.5 kHz gain-bandwidth product as the primary closed-loop bandwidth constraint. For example, a gain of 10 consumes roughly 550 kHz of loop bandwidth, leaving the amplifier near its useful limit and increasing sensitivity to phase-margin changes. Select feedback resistors that do not load the output excessively, and verify stability with the actual source impedance, load capacitance, supply decoupling, and intended output range. A faster family member may be preferable when larger phase margin or faster settling is required.
Do not assume that reverse-battery and over-the-rail input capability makes every input condition safe. The 18 V reverse-battery rating and 5 V over-the-rail operation must be interpreted together with the absolute-maximum table, supply state, and device operating state. External series resistance, clamps, or other protection may still be required for transients, hot-plug events, and connector exposure. Check all input and output voltages against the manufacturer limits before power-up.
The low typical bias current of 880 nA per channel is a key advantage for battery-powered operation, but total system consumption also includes the supply current associated with the chosen feedback network and load. Estimate the average current from the amplifier quiescent current, load demand, sensor current, and regulator efficiency. Ensure the source can support startup and output transients, and include the bypass capacitor specified by the manufacturer close to the power pins.
Informasi Konformitas
The TLV2401ID orderable device is described as automotive grade, but an explicit AEC-Q100 qualification statement and other environmental compliance declarations are not present in the available product records.