TS522IDT - 15MHz Dual Low-Noise Op Amp | STMicroelectronics
MPN: TS522IDT ✓ AktifTS522IDT Ringkasan
An operational amplifier is a voltage-controlled, high-gain analog building block that compares an input signal with a feedback-defined reference. The TS522IDT contains two amplifiers in one package, placing it within the operational-amplifier hierarchy of analog ICs and broader semiconductor signal-processing components. Its dual configuration reduces package count when a board requires two closely related analog channels.
The primary benefits are low input offset voltage, low voltage noise, and high dynamic performance. A 4.5 nV/√Hz noise density supports accurate amplification of small signals, while the 15 MHz gain-bandwidth product provides useful bandwidth for audio, instrumentation, filtering, and general-purpose analog stages. The 7 V/µs slew rate allows the amplifiers to follow changing signals with limited distortion.
Each amplifier can operate with supply voltages between 2.5 V and 15 V, allowing operation from low-voltage analog systems through higher-voltage industrial analog rails. The monolithic dual-amplifier construction is intended to provide matching behavior between the two channels, although circuit-level offset and noise measurements should still be checked in the final design. The 8-pin SOIC package supports conventional surface-mount assembly and is convenient for prototypes as well as production boards.
Typical uses include low-noise audio preamplification, microphone signal conditioning, active filtering, instrumentation amplifiers, sensor interfaces, and analog buffering. Two independent amplifier channels can process stereo audio, implement a differential input stage, or combine filtering with output buffering. Supply-headroom planning remains important because the usable output range depends on the selected rail voltages and output load.
For low-noise layouts, use short feedback paths, keep input and ground connections away from switching nodes, and place input bypass capacitance close to the supply pins. Decoupling requirements and compensation limits should be confirmed in the STMicroelectronics TS522IDT datasheet. Stable operation also depends on following the prescribed capacitive-load limits and providing suitable output-current margin for the connected load.
This product page combines the verified TS522IDT specifications, package information, replacement considerations, comparison parameters, and application guidance. It is intended to help engineers determine whether the dual amplifier fits a specific voltage, bandwidth, noise, and PCB-layout requirement before completing a prototype or production design.
Alternatif penggantian untuk TS522IDT — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian TS522IDT (sama faktor bentuk dan footprint) — berbeda di dalam Amplifier Type, Mounting Type, Package, Slew Rate, Maximum Input Offset Voltage.
TS522ID
✅ Drop-InKontak untuk harga
Lihat Datasheet →TS522IN
✅ Drop-InKontak untuk harga
Lihat Datasheet →OP221GSZ
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
OPA2131UAE4
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
TS522IDT Rating Maksimal & Karakteristik Listrik
| Amplifier Type | Dual precision operational amplifier |
| Number of Amplifiers | 2 amplifiers |
| Gain-Bandwidth Product | 15 MHz |
| Input Voltage Noise Density | 4.5 nV/√Hz |
| Slew Rate | 7 V/µs |
| Minimum Supply Voltage | 2.5 V |
| Maximum Supply Voltage | 15 V |
| Slew Rate | 7 V/µs |
| Paket | 8-pin SOIC |
| Tipe Mounting | Surface Mount |
| Tegangan Pemuat | 2.5 V to 15 V |
| Status RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
TS522IDT 8-pin soic Diamant Konfigurasi Panduan
Konfigurasi pin untuk TS522IDT (8-pin soic pakai pakai). Komponen analog ini memiliki pin masukan, keluaran, dan pengirim daya. Lihat datasheet produsen untuk konfigurasi pin offset null, kompensasi, dan pengaktifan. Ideal untuk peralatan sinyal dan kabel penggandaran.
Tidak ada data diatribut pin yang tersedia untuk TS522IDT.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
TS522IDT cocok untuk 6 aplikasis: Low-Noise Audio Preamplifier, Stereo Audio Buffering, Instrumentation Signal Conditioning, Active Audio Filtering, Sensor Interface Amplification, General-Purpose Analog Buffering.
Low-Noise Audio Preamplifier
The TS522IDT fits low-level audio preamplification because its 4.5 nV/√Hz input-voltage noise density minimizes the amplifier-added noise floor, while the 15 MHz gain-bandwidth product provides bandwidth above the audible band. Place each channel in a noninverting or inverting amplifier stage, and keep the feedback resistors and input traces away from digital and switching-current paths. The 7 V/µs slew rate supports accurate reproduction of moderate-level transients. Confirm output swing, input bias current, and stable capacitive loading for the selected 2.5 V to 15 V supply arrangement.
Direkomendasikan
Stereo Audio Buffering
The TS522IDT can buffer left and right stereo signals in a single 8-pin SOIC, reducing board area compared with two separate single-amplifier packages. Its 4.5 nV/√Hz voltage-noise density is suitable for preserving quiet source signals, and the 15 MHz gain-bandwidth product is substantially above the 20 kHz audio band. Use the amplifiers as unity-gain buffers when driving a higher-impedance downstream stage. Check the datasheet's output-current capability and capacitive-load limits for the exact receiving circuit, and route each channel symmetrically to reduce channel-to-channel timing differences.
Direkomendasikan
Instrumentation Signal Conditioning
The TS522IDT is suitable for conditioning outputs from sensors and instrumentation blocks that contain small signals. Its 4.5 nV/√Hz input-voltage noise density supports low-noise amplification, and the 15 MHz gain-bandwidth product accommodates moderate-bandwidth filters and measurement front ends. The dual package can implement a differential amplifier, a gain stage, and an output buffer. Before selecting it, verify input bias current against sensor impedance, input offset voltage against the required measurement accuracy, and common-mode range against the sensor's output voltage.
Direkomendasikan
Active Audio Filtering
The TS522IDT can implement active low-pass or band-pass sections around audio signals while combining a 15 MHz gain-bandwidth product with a 7 V/µs slew rate. These characteristics support useful closed-loop bandwidth and signal-transition capability beyond the audible range. Build the dual device as two filter channels or use one section for filtering and the other for gain compensation. Use stable resistor and capacitor values, keep feedback loops compact, and observe the manufacturer's capacitive-load guidance because excessive loading can alter phase margin and cause oscillation.
Direkomendasikan
Sensor Interface Amplification
The TS522IDT can amplify low-level sensor outputs when its input characteristics match the sensor's source impedance and signal bandwidth. The 4.5 nV/√Hz voltage-noise density reduces the noise contribution from the amplifier, while the 15 MHz gain-bandwidth product leaves headroom for moderate-frequency conditioning stages. A differential sensor connection can use both amplifiers to amplify and reject common-mode voltage, subject to the verified common-mode range. Check offset and drift for precision measurements, and place high-impedance inputs on guarded or minimally exposed PCB traces.
Direkomendasikan
General-Purpose Analog Buffering
The TS522IDT is appropriate for buffering a higher-impedance source into a lower-impedance load when the selected supply voltage and output-current requirements are met. Its 7 V/µs slew rate provides a practical dynamic-performance margin, and the 15 MHz gain-bandwidth product is suitable for many control, measurement, and communication-related analog blocks. Configure the unused channel for a stable reference or test point rather than leaving it floating. Confirm output swing, stability with the intended load, and thermal behavior using the electrical characteristics and application guidance in the manufacturer datasheet.
Direkomendasikan
Data referensi engineering untuk TS522IDT — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | TS522ID | TS522IN | OP221GSZ | OPA2131UAE4 |
|---|---|---|---|---|---|
| Package | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | Analog Devices | Texas Instruments |
| Amplifier Configuration | Dual | Dual | Dual | Dual | Dual |
Diferensiator Kunci
- Documented low-noise performance (vsOP221GSZ)
- Same-family STMicroelectronics sourcing path (vsOPA2131UAE4)
- Wide single-supply operating range (vsOP221GSZ)
Catatan Desain
Route each high-impedance input directly to its amplifier pin and keep the loop area small. High-value feedback resistors should have short grounded guard geometry where practical, and sensitive analog traces should remain separated from switching nodes, inductors, and high-current return paths. The TS522IDT's 4.5 nV/√Hz noise density can reduce circuit noise, but poor PCB routing can still allow interference and parasitic currents to dominate the result.
Place the required bypass capacitors immediately adjacent to the supply pins and provide a low-impedance ground return. Keep the total voltage applied across the amplifier within the 2.5 V to 15 V operating range. When using dual supplies, confirm the absolute maximum and common-mode limits for each pin. Because the numerical quiescent current and output-current limits are not stated in the available product information, calculate dissipation from the final operating point before production release.
Do not assume that every dual SOIC-8 amplifier has interchangeable channel assignments, supply pins, or stability behavior. Compare the TS522IDT pin description and package drawing against the footprint of the intended alternative, then verify output swing, input bias current, common-mode range, and capacitive-load limits. Excessive capacitive loading or incorrect feedback compensation can cause oscillation even when the nominal 15 MHz bandwidth and 7 V/µs slew rate appear adequate.
For audio or instrumentation stages, evaluate the complete signal chain rather than only the closed-loop gain. The 15 MHz gain-bandwidth product limits the range over which useful low-noise closed-loop gain can be maintained, while the 7 V/µs slew rate influences large-signal behavior. Use short traces, maintain symmetrical channel layout for stereo circuits, and verify settling and distortion in the finished board with realistic source and load impedances.
Informasi Konformitas
No explicit environmental or automotive compliance statements were identified for this ordering code. AEC-Q100 is not applicable to this general-purpose analog amplifier based on its stated product class.