TS522IDT - 15MHz Dual Low-Noise Op Amp | STMicroelectronics
料号: TS522IDT ✓ 量产中TS522IDT 概述
An operational amplifier is a voltage-controlled, high-gain analog building block that compares an input signal with a feedback-defined reference. The TS522IDT contains two amplifiers in one package, placing it within the operational-amplifier hierarchy of analog ICs and broader semiconductor signal-processing components. Its dual configuration reduces package count when a board requires two closely related analog channels.
The primary benefits are low input offset voltage, low voltage noise, and high dynamic performance. A 4.5 nV/√Hz noise density supports accurate amplification of small signals, while the 15 MHz gain-bandwidth product provides useful bandwidth for audio, instrumentation, filtering, and general-purpose analog stages. The 7 V/µs slew rate allows the amplifiers to follow changing signals with limited distortion.
Each amplifier can operate with supply voltages between 2.5 V and 15 V, allowing operation from low-voltage analog systems through higher-voltage industrial analog rails. The monolithic dual-amplifier construction is intended to provide matching behavior between the two channels, although circuit-level offset and noise measurements should still be checked in the final design. The 8-pin SOIC package supports conventional surface-mount assembly and is convenient for prototypes as well as production boards.
Typical uses include low-noise audio preamplification, microphone signal conditioning, active filtering, instrumentation amplifiers, sensor interfaces, and analog buffering. Two independent amplifier channels can process stereo audio, implement a differential input stage, or combine filtering with output buffering. Supply-headroom planning remains important because the usable output range depends on the selected rail voltages and output load.
For low-noise layouts, use short feedback paths, keep input and ground connections away from switching nodes, and place input bypass capacitance close to the supply pins. Decoupling requirements and compensation limits should be confirmed in the STMicroelectronics TS522IDT datasheet. Stable operation also depends on following the prescribed capacitive-load limits and providing suitable output-current margin for the connected load.
This product page combines the verified TS522IDT specifications, package information, replacement considerations, comparison parameters, and application guidance. It is intended to help engineers determine whether the dual amplifier fits a specific voltage, bandwidth, noise, and PCB-layout requirement before completing a prototype or production design.
直接替换替代料: TS522IDT ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: TS522IDT (相同外形与封装尺寸) ——差异在于 Amplifier Type, Mounting Type, Package, Slew Rate, Maximum Input Offset Voltage.
TS522ID
✅ 直接替换联系询价
查看数据手册 →TS522IN
✅ 直接替换联系询价
查看数据手册 →OP221GSZ
✅ 直接替换📋 参考替代料(不在目录中)
OPA2131UAE4
✅ 直接替换📋 参考替代料(不在目录中)
TS522IDT 最大额定值与电气特性
| Amplifier Type | Dual precision operational amplifier |
| Number of Amplifiers | 2 amplifiers |
| Gain-Bandwidth Product | 15 MHz |
| Input Voltage Noise Density | 4.5 nV/√Hz |
| Slew Rate | 7 V/µs |
| Minimum Supply Voltage | 2.5 V |
| Maximum Supply Voltage | 15 V |
| Slew Rate | 7 V/µs |
| 封装 | 8-pin SOIC |
| 安装类型 | Surface Mount |
| 电源电压 | 2.5 V to 15 V |
| RoHS 状态 | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
TS522IDT 8-pin soic 引脚配置指南
TS522IDT(8-pin soic 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: TS522IDT.
请参阅 数据手册 以查看完整引脚配置。
典型应用
TS522IDT 适用于 6 应用s: Low-Noise Audio Preamplifier, Stereo Audio Buffering, Instrumentation Signal Conditioning, Active Audio Filtering, Sensor Interface Amplification, General-Purpose Analog Buffering.
Low-Noise Audio Preamplifier
The TS522IDT fits low-level audio preamplification because its 4.5 nV/√Hz input-voltage noise density minimizes the amplifier-added noise floor, while the 15 MHz gain-bandwidth product provides bandwidth above the audible band. Place each channel in a noninverting or inverting amplifier stage, and keep the feedback resistors and input traces away from digital and switching-current paths. The 7 V/µs slew rate supports accurate reproduction of moderate-level transients. Confirm output swing, input bias current, and stable capacitive loading for the selected 2.5 V to 15 V supply arrangement.
推荐
Stereo Audio Buffering
The TS522IDT can buffer left and right stereo signals in a single 8-pin SOIC, reducing board area compared with two separate single-amplifier packages. Its 4.5 nV/√Hz voltage-noise density is suitable for preserving quiet source signals, and the 15 MHz gain-bandwidth product is substantially above the 20 kHz audio band. Use the amplifiers as unity-gain buffers when driving a higher-impedance downstream stage. Check the datasheet's output-current capability and capacitive-load limits for the exact receiving circuit, and route each channel symmetrically to reduce channel-to-channel timing differences.
推荐
Instrumentation Signal Conditioning
The TS522IDT is suitable for conditioning outputs from sensors and instrumentation blocks that contain small signals. Its 4.5 nV/√Hz input-voltage noise density supports low-noise amplification, and the 15 MHz gain-bandwidth product accommodates moderate-bandwidth filters and measurement front ends. The dual package can implement a differential amplifier, a gain stage, and an output buffer. Before selecting it, verify input bias current against sensor impedance, input offset voltage against the required measurement accuracy, and common-mode range against the sensor's output voltage.
推荐
Active Audio Filtering
The TS522IDT can implement active low-pass or band-pass sections around audio signals while combining a 15 MHz gain-bandwidth product with a 7 V/µs slew rate. These characteristics support useful closed-loop bandwidth and signal-transition capability beyond the audible range. Build the dual device as two filter channels or use one section for filtering and the other for gain compensation. Use stable resistor and capacitor values, keep feedback loops compact, and observe the manufacturer's capacitive-load guidance because excessive loading can alter phase margin and cause oscillation.
推荐
Sensor Interface Amplification
The TS522IDT can amplify low-level sensor outputs when its input characteristics match the sensor's source impedance and signal bandwidth. The 4.5 nV/√Hz voltage-noise density reduces the noise contribution from the amplifier, while the 15 MHz gain-bandwidth product leaves headroom for moderate-frequency conditioning stages. A differential sensor connection can use both amplifiers to amplify and reject common-mode voltage, subject to the verified common-mode range. Check offset and drift for precision measurements, and place high-impedance inputs on guarded or minimally exposed PCB traces.
推荐
General-Purpose Analog Buffering
The TS522IDT is appropriate for buffering a higher-impedance source into a lower-impedance load when the selected supply voltage and output-current requirements are met. Its 7 V/µs slew rate provides a practical dynamic-performance margin, and the 15 MHz gain-bandwidth product is suitable for many control, measurement, and communication-related analog blocks. Configure the unused channel for a stable reference or test point rather than leaving it floating. Confirm output swing, stability with the intended load, and thermal behavior using the electrical characteristics and application guidance in the manufacturer datasheet.
推荐
工程参考数据: TS522IDT ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | TS522ID | TS522IN | OP221GSZ | OPA2131UAE4 |
|---|---|---|---|---|---|
| Package | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | Analog Devices | Texas Instruments |
| Amplifier Configuration | Dual | Dual | Dual | Dual | Dual |
关键差异点
- Documented low-noise performance (对比 OP221GSZ)
- Same-family STMicroelectronics sourcing path (对比 OPA2131UAE4)
- Wide single-supply operating range (对比 OP221GSZ)
设计说明
Route each high-impedance input directly to its amplifier pin and keep the loop area small. High-value feedback resistors should have short grounded guard geometry where practical, and sensitive analog traces should remain separated from switching nodes, inductors, and high-current return paths. The TS522IDT's 4.5 nV/√Hz noise density can reduce circuit noise, but poor PCB routing can still allow interference and parasitic currents to dominate the result.
Place the required bypass capacitors immediately adjacent to the supply pins and provide a low-impedance ground return. Keep the total voltage applied across the amplifier within the 2.5 V to 15 V operating range. When using dual supplies, confirm the absolute maximum and common-mode limits for each pin. Because the numerical quiescent current and output-current limits are not stated in the available product information, calculate dissipation from the final operating point before production release.
Do not assume that every dual SOIC-8 amplifier has interchangeable channel assignments, supply pins, or stability behavior. Compare the TS522IDT pin description and package drawing against the footprint of the intended alternative, then verify output swing, input bias current, common-mode range, and capacitive-load limits. Excessive capacitive loading or incorrect feedback compensation can cause oscillation even when the nominal 15 MHz bandwidth and 7 V/µs slew rate appear adequate.
For audio or instrumentation stages, evaluate the complete signal chain rather than only the closed-loop gain. The 15 MHz gain-bandwidth product limits the range over which useful low-noise closed-loop gain can be maintained, while the 7 V/µs slew rate influences large-signal behavior. Use short traces, maintain symmetrical channel layout for stereo circuits, and verify settling and distortion in the finished board with realistic source and load impedances.
合规信息
No explicit environmental or automotive compliance statements were identified for this ordering code. AEC-Q100 is not applicable to this general-purpose analog amplifier based on its stated product class.