STMicroelectronics

TS942BIN - Dual Micropower Rail-to-Rail Op Amp | ST

MPN: TS942BIN ✗ Akhir Hidup
2.5 V to 10 V Vdss 1.2 µA Id 8-pin PDIP Package
MOQ: 1 |

TS942BIN Ringkasan

The STMicroelectronics TS942BIN is a dual, general-purpose operational amplifier with rail-to-rail output, a 10 kHz gain-bandwidth product, and a typical supply current of 1.2 µA per amplifier. The device operates from 2.5 V to 10 V across a -40 °C to +85 °C temperature range and is supplied in an 8-pin PDIP package.

An operational amplifier is an analog signal-conditioning IC that uses high-gain differential amplification to compare two input voltages. The TS94x series belongs to the low-power operational-amplifier hierarchy, combining rail-to-rail output capability with low bias current. This makes it useful in battery-powered instrumentation, sensor interfaces, buffer stages, and other systems that require low supply current without bipolar-input transistor limitations.

Key characteristics include two amplifier circuits, rail-to-rail output operation, a 10 kHz gain-bandwidth product, a slew rate of 0.0045 V/µs, input offset voltage of up to 2 mV, and input bias current as low as 1 pA. The low 1.2 µA supply current is particularly valuable in portable equipment, while the 2.5 V minimum supply voltage supports low-energy system rails.

The micropower architecture favors low-frequency signal conditioning rather than high-speed amplification. Its 10 kHz gain-bandwidth product limits usable closed-loop bandwidth according to the selected feedback network, while the 0.0045 V/µs slew rate governs large-signal response. Rail-to-rail output improves output swing on low-voltage supplies, although input common-mode range, output loading, and stability still require careful circuit-level evaluation.

Typical uses include buffering sensor outputs, amplifying low-level signals in battery-operated instruments, driving analog measurement inputs, and providing gain stages in portable monitoring equipment. The dual configuration can implement two independent amplifiers in instrumentation, filtering, or signal-conditioning circuits while reducing package count.

Layout should keep input, feedback, and decoupling connections short, and should avoid routing high-impedance input traces beside switching or high-current paths. Place the supply bypass capacitor close to the device, observe common-mode and output-swing limits, and verify stability with the intended source and load impedances. Because the TS942BIN is obsolete, maintain a controlled last-time-buy plan for maintenance and repair production.

Alternatif penggantian untuk TS942BIN — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.

Variasi di dalam seri ini

Model-series yang sama yang kompatibel dengan penggantian TS942BIN (sama faktor bentuk dan footprint) — berbeda di dalam Amplifier Type, Input Offset Voltage, Package.

STMicroelectronics
Amplifier Type: Dual general-purpose operational amplifier
Input Offset Voltage: 0.15 mV
Package: 8-pin Mini DIP, 7.62 mm row spacing
Bandingkan dengan TS942BIN →

Tidak ada alternatif pengganti yang tersedia untuk produk ini.

Permintaan Alternatif

TS942BIN Rating Maksimal & Karakteristik Listrik

Manufacturer STMicroelectronics
Product Type Dual general-purpose operational amplifier
Number of Circuits 2 circuits
Amplifier Type General Purpose
Tipe Output Rail-to-rail
Supply Voltage Range 2.5 V to 10 V
Arus Pemuat 1.2 µA
Gain-Bandwidth Product 10 kHz
Slew Rate 0.0045 V/µs
Input Offset Voltage 2 mV maximum
Input Bias Current 1 pA
Rentang Suhu Kerja -40 °C to +85 °C
Paket 8-pin PDIP
Tipe Mounting Through-hole
Operating Temperature Classification Industrial, -40 °C to +85 °C
Status Lingkungan Hidup Obsolete
Packaging Tube
AEC-Q100 Qualification Not applicable

TS942BIN 8-pin pdip Diamant Konfigurasi Panduan

Konfigurasi pin untuk TS942BIN (8-pin pdip pakai pakai). Komponen analog ini memiliki pin masukan, keluaran, dan pengirim daya. Lihat datasheet produsen untuk konfigurasi pin offset null, kompensasi, dan pengaktifan. Ideal untuk peralatan sinyal dan kabel penggandaran.

Diamant diagram pakai pakai 8-pin pdip untuk TS942BIN

Tidak ada data diatribut pin yang tersedia untuk TS942BIN.

Lihat ke: datasheet produk untuk konfigurasi pin penuh.

Aplikasi Umum

TS942BIN cocok untuk 6 aplikasis: Battery-Powered Sensor Conditioning, Portable Measurement Instrumentation, Low-Voltage Analog Buffering, Industrial Process Monitoring, Low-Power Gain Stage, Legacy Control-System Maintenance.

🧩

Battery-Powered Sensor Conditioning

The TS942BIN fits battery-powered sensor conditioning because its dual amplifiers operate from 2.5 V to 10 V while drawing only 1.2 µA of supply current. One amplifier can amplify a low-level sensor signal and the second can provide buffering or gain, reducing package count in a compact instrument. Input bias current down to 1 pA helps preserve weak signals from high-impedance sources. The 10 kHz gain-bandwidth product is appropriate for slowly changing environmental or biometric measurements rather than high-speed signals. Designers should verify the input common-mode range and offset error against the sensor output, then ensure the chosen gain and feedback network provide acceptable settling.

🔧

Portable Measurement Instrumentation

The TS942BIN is useful in portable measurement instruments where every microamp of supply current affects battery life. Its two general-purpose rail-to-rail-output channels can process two related low-frequency signals, such as a measurement input and a reference buffer, within one 8-pin PDIP package. Operation from 2.5 V allows direct use of a low-voltage battery-derived rail. The rail-to-rail output maximizes usable signal span, while the 0.0045 V/µs slew rate supports moderate-amplitude, low-frequency waveforms. For accurate readings, include offset and bias-current error in the system budget and check sensor settling time against the amplifier's 10 kHz closed-loop bandwidth.

📡

Low-Voltage Analog Buffering

The TS942BIN can serve as a low-voltage analog buffer when a sensor or divider must drive a higher-impedance downstream circuit. Its rail-to-rail output provides greater usable output range than a fixed-rail amplifier on a 2.5 V supply, while the low input bias current minimizes disturbance of high-impedance sources. Two independent channels allow simultaneous buffering or a voltage follower paired with a gain stage. Because the gain-bandwidth product is only 10 kHz, keep the signal bandwidth well below the closed-loop limit and place feedback components close to the amplifier. Confirm output settling and capacitive-load stability with the actual source and load.

🏭

Industrial Process Monitoring

The TS942BIN is applicable to slow industrial process-monitoring circuits operating from a low-voltage regulated rail. Its -40 °C to +85 °C rating supports industrial-temperature equipment, and the dual configuration can handle one sensor channel and one reference or control channel. The 1.2 µA supply current is useful in distributed, power-limited monitoring nodes, while rail-to-rail output preserves signal headroom. The device is best suited to temperature, pressure, or level signals with limited bandwidth. Validate the input common-mode limits, electrical isolation strategy, grounding, and protection network; the operating temperature rating does not replace the system requirements for surge, noise, and safety compliance.

📱

Low-Power Gain Stage

The TS942BIN can implement a low-power gain stage for low-frequency analog signals when a 10 kHz gain-bandwidth product is sufficient. Its rail-to-rail output reduces clipping near the positive or negative supply limit, and the dual layout permits cascaded or parallel functional blocks. A practical example is conditioning a bridge sensor or resistive divider before an ADC input. Select feedback resistors with values that preserve the required noise and offset performance, and confirm that the selected closed-loop gain does not exceed the usable bandwidth at the signal frequency. Also evaluate the 2 mV maximum input offset against the smallest signal level that the system must resolve.

🖥️

Legacy Control-System Maintenance

The TS942BIN is particularly relevant to maintenance of legacy control and measurement boards that originally used an 8-pin PDIP dual operational amplifier. Its established supply range, low power, rail-to-rail output, and two-amplifier configuration allow a board-level repair without changing the surrounding architecture. The -40 °C to +85 °C range covers many industrial environments, while the 1.2 µA supply current supports existing low-power designs. For production continuity, review the obsolete status, obtain traceable remaining stock, and inspect pin condition and solderability. Confirm that any proposed substitute matches the package, pinout, common-mode limits, and stability characteristics before substituting it into the legacy board.

Ringkasan Produk Direkomendasikan

TS942IDT Same TS94x electrical family in a different package Digunakan di dalam: Battery-Powered Sensor Conditioning, Portable Measurement Instrumentation, Low-Voltage Analog Buffering, Industrial Process Monitoring, Low-Power Gain Stage, Legacy Control-System Maintenance
What is the TS942BIN?
The TS942BIN is a dual, general-purpose, rail-to-rail micropower operational amplifier from STMicroelectronics. It contains two amplifier circuits in an 8-pin PDIP package, operates from 2.5 V to 10 V, and is designed for low-power instrumentation, buffering, and sensor-signal conditioning. The STMicroelectronics TS94x product page identifies the series as an operational-amplifier family for low-voltage operation.
What is the operating voltage of TS942BIN?
The TS942BIN operates from 2.5 V to 10 V. According to the STMicroelectronics TS94x product page, this range supports low-voltage portable, instrumentation, and signal-conditioning systems. The manufacturer lists the family for operation over -40 °C to +85 °C, making the device suitable for industrial-temperature equipment when its electrical limits are respected.
What are the key specifications of TS942BIN that engineers should know?
The TS942BIN combines two rail-to-rail-output amplifiers, a 10 kHz gain-bandwidth product, a 0.0045 V/µs slew rate, and a typical supply current of 1.2 µA in an 8-pin PDIP package. Its maximum input offset voltage is 2 mV, while input bias current can be as low as 1 pA. These characteristics position it for low-power, low-frequency analog signal-conditioning rather than high-speed waveform applications.
Where to download the TS942BIN datasheet PDF?
The official TS942BIN technical information is available through the STMicroelectronics TS94x product page at https://www.st.com/en/amplifiers-and-comparators/ts942.html. Use the manufacturer's datasheet link on that page for the authoritative pin description, electrical characteristics, application guidance, and ordering information. The indexed document describes the TS94x family as rail-to-rail micropower operational amplifiers.
Where can I find the TS942BIN pinout?
The TS942BIN uses an 8-pin PDIP package, and its authoritative pin assignment should be taken from the pin-description table in the STMicroelectronics TS94x datasheet. Assign PCB tracks directly from that table rather than relying on a generic dual-op-amp drawing, because dual amplifier packages can differ in output, input, and supply-pin ordering between manufacturers and families.
Is TS942BIN suitable for battery-powered sensor applications?
Yes, the TS942BIN is suitable for battery-powered sensor interfaces because its supply current is 1.2 µA and its minimum operating supply is 2.5 V. Its rail-to-rail output and low input bias current also help preserve signal range and minimize loading on high-impedance sensors. The 10 kHz gain-bandwidth product limits it mainly to slow-changing or low-frequency measurements.
What can replace the obsolete TS942BIN?
No confirmed five-part drop-in replacement set can be established from the available manufacturer and cross-reference information. A valid replacement must duplicate the 8-pin PDIP footprint, dual-amplifier pinout, 2.5 V to 10 V supply range, rail-to-rail output, and approximately 1.2 µA supply current. Use the Request a Quote form on this page to identify current availability and qualification requirements for maintenance production.
Can TS942IDT replace TS942BIN?
The TS942IDT is a member of the same TS94x family, but it is not automatically a pin-to-pin replacement for the TS942BIN because its package and ordering code differ. The TS942BIN is specified in an 8-pin PDIP package, so require the replacement's complete pin assignment, package drawing, and electrical ratings to match before treating it as a drop-in substitute. A same-family comparison alone is insufficient for PCB reuse.
What is the best cross-brand equivalent for TS942BIN?
No cross-brand equivalent is listed here as a confirmed drop-in replacement because the available cross-reference material does not identify a candidate with a matching 8-pin PDIP footprint and verified pinout. The TS942BIN has a demanding combination of a 2.5 V minimum supply, approximately 1.2 µA supply current, rail-to-rail output, and dual-amplifier configuration. Submit the required footprint and electrical limits through the Request a Quote form for sourcing review.
TS942BIN vs TS942IDT - which is better for a legacy PCB?
The TS942BIN is the better choice for a PCB specifically designed around an 8-pin PDIP footprint, while TS942IDT should be considered only after its package and pin mapping have been compared with the original design. Both belong to the TS94x family, but family membership does not prove mechanical or pin compatibility. The original board layout and datasheet pin table determine whether either option can be installed without redesign.
When should I choose TS942BIN over another dual op amp?
Choose the TS942BIN when an obsolete system requires an 8-pin PDIP dual op amp with rail-to-rail output, low power, and operation from 2.5 V to 10 V. It is particularly relevant for maintaining legacy instrumentation where redesigning the PCB would be expensive. For new mixed-signal or high-speed designs, alternatives with wider bandwidth, stronger output drive, or better availability may be more appropriate.
Is TS942BIN suitable for instrumentation and buffer applications?
Yes, the TS942BIN is appropriate for low-frequency instrumentation and buffer applications because it provides dual rail-to-rail-output amplifiers, a 10 kHz gain-bandwidth product, and low input bias current. Its 1.2 µA supply current supports portable measurements. Check the input common-mode range, capacitive loading, offset voltage, and required settling accuracy before selecting a gain value.
How much current does the TS942BIN consume?
The TS942BIN has a specified supply current of 1.2 µA for the dual operational-amplifier device. Its low consumption makes it useful for battery-powered instrumentation and other low-energy analog systems. Actual system demand also depends on supply voltage, output loading, input bias current, and the selected feedback network, so include external divider and sensor currents when calculating total power budget.
Where to buy TS942BIN online?
Use the Request a Quote form on this page to request TS942BIN availability, lead time, and production quantity options. The part is listed as obsolete, so supply may depend on remaining factory stock or approved channel inventory. Include the 8-pin PDIP package, operating-temperature range of -40 °C to +85 °C, and any required inspection or traceability criteria with the request.
What is the price of TS942BIN?
The current commercial price for the obsolete TS942BIN is best obtained through the Request a Quote form on this page rather than a static price statement. The form can account for requested quantity, packaging, traceability, and current channel availability. Because the device is obsolete, a quote should also clarify whether the offered units are original factory stock and what lifecycle risk applies to future maintenance orders.

Data referensi engineering untuk TS942BIN — pembandingan, panduan desain, dan informasi konformitas.

Panduan Pemilihan

Choose the TS942BIN when maintaining an 8-pin PDIP board that requires a dual rail-to-rail operational amplifier with very low supply current. It is strongest in legacy instrumentation, battery-powered sensing, and low-frequency buffering where a 10 kHz gain-bandwidth product is sufficient and the operating rail remains between 2.5 V and 10 V. Do not select it for high-speed waveform amplification, precision instrumentation requiring substantially lower offset, or designs requiring an active output rail beyond the stated supply range. The TS942IDT can serve as a same-family sourcing reference, but it should be adopted only after its package and pinout are proven equivalent. For new designs, prioritize an active, well-supported amplifier unless continuity with an existing TS942BIN footprint is essential.

Pembandingan dengan Alternatif

Parameter Umum Produk Ini TS942IDT
Brand STMicroelectronics STMicroelectronics
Output Type Rail-to-rail Rail-to-rail

Diferensiator Kunci

  • Dual rail-to-rail micropower channels in one package (vsTS942IDT)
  • Low-voltage operation suitable for portable analog systems (vsTS942IDT)
  • Input behavior suited to high-impedance sources (vsTS942IDT)

Catatan Desain

Use the pin-description table in the manufacturer datasheet when assigning PCB tracks, especially for the two independent amplifier channels. Keep high-impedance input and feedback nets short, avoid parallel routing with switching nodes, and place input biasing or source components close to the relevant amplifier. For legacy repair work, verify the package origin and pin numbering rather than assuming that every dual 8-pin operational amplifier has the same order.

The TS942BIN is designed for low-power operation, but the complete analog channel also consumes current through sensor dividers, feedback networks, and external reference circuits. Include those loads when calculating battery life. Decouple the supply close to the device with a suitable bypass capacitor and route the return directly to the amplifier ground to minimize supply ripple entering the signal path.

Treat the 10 kHz gain-bandwidth product as the principal dynamic limit. Select closed-loop gain so that the desired signal bandwidth remains well below the amplifier's usable bandwidth, and check large-signal response against the 0.0045 V/µs slew rate. For high-impedance sources, account for the specified input bias current and evaluate thermal drift, input offset voltage, and parasitic capacitance before confirming accuracy.

Do not assume that every TS94x ordering code is mechanically interchangeable with the TS942BIN. A replacement must match the 8-pin PDIP footprint, complete pin assignment, supply range, input common-mode limits, output swing, and stability behavior. Because the TS942BIN is obsolete, incoming inspection, solderability checks, and traceable sourcing are especially important for maintenance quantities intended for long-lived equipment.

Informasi Konformitas

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bebas Logam Lengket
Unknown
Bebas Halogena
Unknown
Mineral Konflik
Unknown

The TS942BIN is an obsolete general-purpose operational amplifier rather than an automotive-qualified device. Specific environmental and material compliance declarations should be confirmed against the documentation associated with any remaining stock.

Data disahkan pada: 2026-11-16 — data disahkan dan disusun oleh tim engineering komponen XAIPART

Pencarian Terkait

TS942BIN datasheet TS942BIN pinout TS942BIN datasheet pdf TS942BIN equivalent TS942BIN replacement TS942BIN cross reference TS942BIN vs TS942IDT TS942BIN footprint TS942BIN application circuit TS942BIN price TS942BIN stock STMicroelectronics TS942BIN TS942BIN 8-DIP op amp TS942BIN rail-to-rail micropower amplifier

Komponen dan Istilah Terkait

STMicroelectronics TS942BIN TS942IDT TS94x series operational amplifier dual operational amplifier general-purpose amplifier micropower amplifier rail-to-rail output analog signal conditioning voltage feedback amplifier low-dropout linear regulator semiconductor 8-pin PDIP PDIP package through-hole package surface-mount alternative gain-bandwidth product slew rate input bias current input offset voltage supply current sensor interface battery-powered instrumentation
Kutipan Cepat RFQ
Isi detail lengkap — tim penjualan kami akan membalas dalam 24 jam
Nomor Part Manufaktur Paket QTY Harga Target Lengkap
✓
Kutipan telah disubmit!

Kami akan membalas email Anda dalam 24 jam

1
RFQ Dikirim
2
Kutipan Diterima
3
Order Ditempatkan
4
Pembayaran
5
Dikirim
6
Dikirim
Lihat Detil RFQ