TS942BIN - Dual Micropower Rail-to-Rail Op Amp | ST
MPN: TS942BIN ✗ Cuối đờiTS942BIN Tóm tắt
An operational amplifier is an analog signal-conditioning IC that uses high-gain differential amplification to compare two input voltages. The TS94x series belongs to the low-power operational-amplifier hierarchy, combining rail-to-rail output capability with low bias current. This makes it useful in battery-powered instrumentation, sensor interfaces, buffer stages, and other systems that require low supply current without bipolar-input transistor limitations.
Key characteristics include two amplifier circuits, rail-to-rail output operation, a 10 kHz gain-bandwidth product, a slew rate of 0.0045 V/µs, input offset voltage of up to 2 mV, and input bias current as low as 1 pA. The low 1.2 µA supply current is particularly valuable in portable equipment, while the 2.5 V minimum supply voltage supports low-energy system rails.
The micropower architecture favors low-frequency signal conditioning rather than high-speed amplification. Its 10 kHz gain-bandwidth product limits usable closed-loop bandwidth according to the selected feedback network, while the 0.0045 V/µs slew rate governs large-signal response. Rail-to-rail output improves output swing on low-voltage supplies, although input common-mode range, output loading, and stability still require careful circuit-level evaluation.
Typical uses include buffering sensor outputs, amplifying low-level signals in battery-operated instruments, driving analog measurement inputs, and providing gain stages in portable monitoring equipment. The dual configuration can implement two independent amplifiers in instrumentation, filtering, or signal-conditioning circuits while reducing package count.
Layout should keep input, feedback, and decoupling connections short, and should avoid routing high-impedance input traces beside switching or high-current paths. Place the supply bypass capacitor close to the device, observe common-mode and output-swing limits, and verify stability with the intended source and load impedances. Because the TS942BIN is obsolete, maintain a controlled last-time-buy plan for maintenance and repair production.
Bộ thay thế dễ dàng lắp đặt cho TS942BIN — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với TS942BIN (cùng hình factor và footprint) — khác nhau ở Amplifier Type, Input Offset Voltage, Package.
Không có bộ thay thế dễ dàng lắp đặt sẵn có cho sản phẩm này.
Yêu cầu các bộ thay thếTS942BIN Tỷ lệ tối đa & tính chất điện
| Manufacturer | STMicroelectronics |
| Product Type | Dual general-purpose operational amplifier |
| Number of Circuits | 2 circuits |
| Amplifier Type | General Purpose |
| Kiểu đầu ra | Rail-to-rail |
| Supply Voltage Range | 2.5 V to 10 V |
| Điện áp cung cấp | 1.2 µA |
| Gain-Bandwidth Product | 10 kHz |
| Slew Rate | 0.0045 V/µs |
| Input Offset Voltage | 2 mV maximum |
| Input Bias Current | 1 pA |
| Khoảng nhiệt độ hoạt động | -40 °C to +85 °C |
| Hộp | 8-pin PDIP |
| Kiểu lắp đặt | Through-hole |
| Operating Temperature Classification | Industrial, -40 °C to +85 °C |
| Trạng thái vòng đời | Obsolete |
| Packaging | Tube |
| AEC-Q100 Qualification | Not applicable |
Hướng dẫn cấu hình chân TS942BIN 8-pin pdip
Cấu hình chân cho TS942BIN (8-pin pdip gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho TS942BIN.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
TS942BIN phù hợp cho 6 Áp dụngs: Battery-Powered Sensor Conditioning, Portable Measurement Instrumentation, Low-Voltage Analog Buffering, Industrial Process Monitoring, Low-Power Gain Stage, Legacy Control-System Maintenance.
Battery-Powered Sensor Conditioning
The TS942BIN fits battery-powered sensor conditioning because its dual amplifiers operate from 2.5 V to 10 V while drawing only 1.2 µA of supply current. One amplifier can amplify a low-level sensor signal and the second can provide buffering or gain, reducing package count in a compact instrument. Input bias current down to 1 pA helps preserve weak signals from high-impedance sources. The 10 kHz gain-bandwidth product is appropriate for slowly changing environmental or biometric measurements rather than high-speed signals. Designers should verify the input common-mode range and offset error against the sensor output, then ensure the chosen gain and feedback network provide acceptable settling.
Được đề xuất
Portable Measurement Instrumentation
The TS942BIN is useful in portable measurement instruments where every microamp of supply current affects battery life. Its two general-purpose rail-to-rail-output channels can process two related low-frequency signals, such as a measurement input and a reference buffer, within one 8-pin PDIP package. Operation from 2.5 V allows direct use of a low-voltage battery-derived rail. The rail-to-rail output maximizes usable signal span, while the 0.0045 V/µs slew rate supports moderate-amplitude, low-frequency waveforms. For accurate readings, include offset and bias-current error in the system budget and check sensor settling time against the amplifier's 10 kHz closed-loop bandwidth.
Được đề xuất
Low-Voltage Analog Buffering
The TS942BIN can serve as a low-voltage analog buffer when a sensor or divider must drive a higher-impedance downstream circuit. Its rail-to-rail output provides greater usable output range than a fixed-rail amplifier on a 2.5 V supply, while the low input bias current minimizes disturbance of high-impedance sources. Two independent channels allow simultaneous buffering or a voltage follower paired with a gain stage. Because the gain-bandwidth product is only 10 kHz, keep the signal bandwidth well below the closed-loop limit and place feedback components close to the amplifier. Confirm output settling and capacitive-load stability with the actual source and load.
Được đề xuất
Industrial Process Monitoring
The TS942BIN is applicable to slow industrial process-monitoring circuits operating from a low-voltage regulated rail. Its -40 °C to +85 °C rating supports industrial-temperature equipment, and the dual configuration can handle one sensor channel and one reference or control channel. The 1.2 µA supply current is useful in distributed, power-limited monitoring nodes, while rail-to-rail output preserves signal headroom. The device is best suited to temperature, pressure, or level signals with limited bandwidth. Validate the input common-mode limits, electrical isolation strategy, grounding, and protection network; the operating temperature rating does not replace the system requirements for surge, noise, and safety compliance.
Được đề xuất
Low-Power Gain Stage
The TS942BIN can implement a low-power gain stage for low-frequency analog signals when a 10 kHz gain-bandwidth product is sufficient. Its rail-to-rail output reduces clipping near the positive or negative supply limit, and the dual layout permits cascaded or parallel functional blocks. A practical example is conditioning a bridge sensor or resistive divider before an ADC input. Select feedback resistors with values that preserve the required noise and offset performance, and confirm that the selected closed-loop gain does not exceed the usable bandwidth at the signal frequency. Also evaluate the 2 mV maximum input offset against the smallest signal level that the system must resolve.
Được đề xuất
Legacy Control-System Maintenance
The TS942BIN is particularly relevant to maintenance of legacy control and measurement boards that originally used an 8-pin PDIP dual operational amplifier. Its established supply range, low power, rail-to-rail output, and two-amplifier configuration allow a board-level repair without changing the surrounding architecture. The -40 °C to +85 °C range covers many industrial environments, while the 1.2 µA supply current supports existing low-power designs. For production continuity, review the obsolete status, obtain traceable remaining stock, and inspect pin condition and solderability. Confirm that any proposed substitute matches the package, pinout, common-mode limits, and stability characteristics before substituting it into the legacy board.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho TS942BIN — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | TS942IDT |
|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics |
| Output Type | Rail-to-rail | Rail-to-rail |
Bảo phân biệt quan trọng
- Dual rail-to-rail micropower channels in one package (vsTS942IDT)
- Low-voltage operation suitable for portable analog systems (vsTS942IDT)
- Input behavior suited to high-impedance sources (vsTS942IDT)
Ghi chú thiết kế
Use the pin-description table in the manufacturer datasheet when assigning PCB tracks, especially for the two independent amplifier channels. Keep high-impedance input and feedback nets short, avoid parallel routing with switching nodes, and place input biasing or source components close to the relevant amplifier. For legacy repair work, verify the package origin and pin numbering rather than assuming that every dual 8-pin operational amplifier has the same order.
The TS942BIN is designed for low-power operation, but the complete analog channel also consumes current through sensor dividers, feedback networks, and external reference circuits. Include those loads when calculating battery life. Decouple the supply close to the device with a suitable bypass capacitor and route the return directly to the amplifier ground to minimize supply ripple entering the signal path.
Treat the 10 kHz gain-bandwidth product as the principal dynamic limit. Select closed-loop gain so that the desired signal bandwidth remains well below the amplifier's usable bandwidth, and check large-signal response against the 0.0045 V/µs slew rate. For high-impedance sources, account for the specified input bias current and evaluate thermal drift, input offset voltage, and parasitic capacitance before confirming accuracy.
Do not assume that every TS94x ordering code is mechanically interchangeable with the TS942BIN. A replacement must match the 8-pin PDIP footprint, complete pin assignment, supply range, input common-mode limits, output swing, and stability behavior. Because the TS942BIN is obsolete, incoming inspection, solderability checks, and traceable sourcing are especially important for maintenance quantities intended for long-lived equipment.
Thông tin tuân thủ
The TS942BIN is an obsolete general-purpose operational amplifier rather than an automotive-qualified device. Specific environmental and material compliance declarations should be confirmed against the documentation associated with any remaining stock.