TS942BIN - Dual Micropower Rail-to-Rail Op Amp | ST
料号: TS942BIN ✗ 停产TS942BIN 概述
An operational amplifier is an analog signal-conditioning IC that uses high-gain differential amplification to compare two input voltages. The TS94x series belongs to the low-power operational-amplifier hierarchy, combining rail-to-rail output capability with low bias current. This makes it useful in battery-powered instrumentation, sensor interfaces, buffer stages, and other systems that require low supply current without bipolar-input transistor limitations.
Key characteristics include two amplifier circuits, rail-to-rail output operation, a 10 kHz gain-bandwidth product, a slew rate of 0.0045 V/µs, input offset voltage of up to 2 mV, and input bias current as low as 1 pA. The low 1.2 µA supply current is particularly valuable in portable equipment, while the 2.5 V minimum supply voltage supports low-energy system rails.
The micropower architecture favors low-frequency signal conditioning rather than high-speed amplification. Its 10 kHz gain-bandwidth product limits usable closed-loop bandwidth according to the selected feedback network, while the 0.0045 V/µs slew rate governs large-signal response. Rail-to-rail output improves output swing on low-voltage supplies, although input common-mode range, output loading, and stability still require careful circuit-level evaluation.
Typical uses include buffering sensor outputs, amplifying low-level signals in battery-operated instruments, driving analog measurement inputs, and providing gain stages in portable monitoring equipment. The dual configuration can implement two independent amplifiers in instrumentation, filtering, or signal-conditioning circuits while reducing package count.
Layout should keep input, feedback, and decoupling connections short, and should avoid routing high-impedance input traces beside switching or high-current paths. Place the supply bypass capacitor close to the device, observe common-mode and output-swing limits, and verify stability with the intended source and load impedances. Because the TS942BIN is obsolete, maintain a controlled last-time-buy plan for maintenance and repair production.
直接替换替代料: TS942BIN ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: TS942BIN (相同外形与封装尺寸) ——差异在于 Amplifier Type, Input Offset Voltage, Package.
该产品暂无直接替换替代料。
请求替代料TS942BIN 最大额定值与电气特性
| Manufacturer | STMicroelectronics |
| Product Type | Dual general-purpose operational amplifier |
| Number of Circuits | 2 circuits |
| Amplifier Type | General Purpose |
| 输出类型 | Rail-to-rail |
| Supply Voltage Range | 2.5 V to 10 V |
| 电源电流 | 1.2 µA |
| Gain-Bandwidth Product | 10 kHz |
| Slew Rate | 0.0045 V/µs |
| Input Offset Voltage | 2 mV maximum |
| Input Bias Current | 1 pA |
| 工作温度范围 | -40 °C to +85 °C |
| 封装 | 8-pin PDIP |
| 安装类型 | Through-hole |
| Operating Temperature Classification | Industrial, -40 °C to +85 °C |
| 生命周期状态 | Obsolete |
| Packaging | Tube |
| AEC-Q100 Qualification | Not applicable |
TS942BIN 8-pin pdip 引脚配置指南
TS942BIN(8-pin pdip 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: TS942BIN.
请参阅 数据手册 以查看完整引脚配置。
典型应用
TS942BIN 适用于 6 应用s: Battery-Powered Sensor Conditioning, Portable Measurement Instrumentation, Low-Voltage Analog Buffering, Industrial Process Monitoring, Low-Power Gain Stage, Legacy Control-System Maintenance.
Battery-Powered Sensor Conditioning
The TS942BIN fits battery-powered sensor conditioning because its dual amplifiers operate from 2.5 V to 10 V while drawing only 1.2 µA of supply current. One amplifier can amplify a low-level sensor signal and the second can provide buffering or gain, reducing package count in a compact instrument. Input bias current down to 1 pA helps preserve weak signals from high-impedance sources. The 10 kHz gain-bandwidth product is appropriate for slowly changing environmental or biometric measurements rather than high-speed signals. Designers should verify the input common-mode range and offset error against the sensor output, then ensure the chosen gain and feedback network provide acceptable settling.
推荐
Portable Measurement Instrumentation
The TS942BIN is useful in portable measurement instruments where every microamp of supply current affects battery life. Its two general-purpose rail-to-rail-output channels can process two related low-frequency signals, such as a measurement input and a reference buffer, within one 8-pin PDIP package. Operation from 2.5 V allows direct use of a low-voltage battery-derived rail. The rail-to-rail output maximizes usable signal span, while the 0.0045 V/µs slew rate supports moderate-amplitude, low-frequency waveforms. For accurate readings, include offset and bias-current error in the system budget and check sensor settling time against the amplifier's 10 kHz closed-loop bandwidth.
推荐
Low-Voltage Analog Buffering
The TS942BIN can serve as a low-voltage analog buffer when a sensor or divider must drive a higher-impedance downstream circuit. Its rail-to-rail output provides greater usable output range than a fixed-rail amplifier on a 2.5 V supply, while the low input bias current minimizes disturbance of high-impedance sources. Two independent channels allow simultaneous buffering or a voltage follower paired with a gain stage. Because the gain-bandwidth product is only 10 kHz, keep the signal bandwidth well below the closed-loop limit and place feedback components close to the amplifier. Confirm output settling and capacitive-load stability with the actual source and load.
推荐
Industrial Process Monitoring
The TS942BIN is applicable to slow industrial process-monitoring circuits operating from a low-voltage regulated rail. Its -40 °C to +85 °C rating supports industrial-temperature equipment, and the dual configuration can handle one sensor channel and one reference or control channel. The 1.2 µA supply current is useful in distributed, power-limited monitoring nodes, while rail-to-rail output preserves signal headroom. The device is best suited to temperature, pressure, or level signals with limited bandwidth. Validate the input common-mode limits, electrical isolation strategy, grounding, and protection network; the operating temperature rating does not replace the system requirements for surge, noise, and safety compliance.
推荐
Low-Power Gain Stage
The TS942BIN can implement a low-power gain stage for low-frequency analog signals when a 10 kHz gain-bandwidth product is sufficient. Its rail-to-rail output reduces clipping near the positive or negative supply limit, and the dual layout permits cascaded or parallel functional blocks. A practical example is conditioning a bridge sensor or resistive divider before an ADC input. Select feedback resistors with values that preserve the required noise and offset performance, and confirm that the selected closed-loop gain does not exceed the usable bandwidth at the signal frequency. Also evaluate the 2 mV maximum input offset against the smallest signal level that the system must resolve.
推荐
Legacy Control-System Maintenance
The TS942BIN is particularly relevant to maintenance of legacy control and measurement boards that originally used an 8-pin PDIP dual operational amplifier. Its established supply range, low power, rail-to-rail output, and two-amplifier configuration allow a board-level repair without changing the surrounding architecture. The -40 °C to +85 °C range covers many industrial environments, while the 1.2 µA supply current supports existing low-power designs. For production continuity, review the obsolete status, obtain traceable remaining stock, and inspect pin condition and solderability. Confirm that any proposed substitute matches the package, pinout, common-mode limits, and stability characteristics before substituting it into the legacy board.
推荐
推荐产品汇总
工程参考数据: TS942BIN ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | TS942IDT |
|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics |
| Output Type | Rail-to-rail | Rail-to-rail |
关键差异点
- Dual rail-to-rail micropower channels in one package (对比 TS942IDT)
- Low-voltage operation suitable for portable analog systems (对比 TS942IDT)
- Input behavior suited to high-impedance sources (对比 TS942IDT)
设计说明
Use the pin-description table in the manufacturer datasheet when assigning PCB tracks, especially for the two independent amplifier channels. Keep high-impedance input and feedback nets short, avoid parallel routing with switching nodes, and place input biasing or source components close to the relevant amplifier. For legacy repair work, verify the package origin and pin numbering rather than assuming that every dual 8-pin operational amplifier has the same order.
The TS942BIN is designed for low-power operation, but the complete analog channel also consumes current through sensor dividers, feedback networks, and external reference circuits. Include those loads when calculating battery life. Decouple the supply close to the device with a suitable bypass capacitor and route the return directly to the amplifier ground to minimize supply ripple entering the signal path.
Treat the 10 kHz gain-bandwidth product as the principal dynamic limit. Select closed-loop gain so that the desired signal bandwidth remains well below the amplifier's usable bandwidth, and check large-signal response against the 0.0045 V/µs slew rate. For high-impedance sources, account for the specified input bias current and evaluate thermal drift, input offset voltage, and parasitic capacitance before confirming accuracy.
Do not assume that every TS94x ordering code is mechanically interchangeable with the TS942BIN. A replacement must match the 8-pin PDIP footprint, complete pin assignment, supply range, input common-mode limits, output swing, and stability behavior. Because the TS942BIN is obsolete, incoming inspection, solderability checks, and traceable sourcing are especially important for maintenance quantities intended for long-lived equipment.
合规信息
The TS942BIN is an obsolete general-purpose operational amplifier rather than an automotive-qualified device. Specific environmental and material compliance declarations should be confirmed against the documentation associated with any remaining stock.