集積回路

サブカテゴリ

📁 ADC/DAC 3,100+ 製品 📁 アンプIC 1,900+ 製品 📁 オーディオコーデック 18 製品 📁 オーディオIC 2 製品 📁 クロック＆タイミング 660+ 製品 📁 Comparator ICs 1 製品 📁 DSP 1,100+ 製品 📁 データ収集IC 2 製品 📁 デジタルポテンショメータ 4 製品 📁 ディスプレイドライバ＆コントローラ 1 製品 📁 FPGA & CPLD 7,300+ 製品 📁 インターフェースIC 3,300+ 製品 📁 LEDドライバ 1 製品 📁 ロジックIC 460+ 製品 📁 メモリIC 870+ 製品 📁 マイクロコントローラ 20,000+ 製品 📁 マイクロプロセッサ 4 製品 📁 モータドライバ 1 製品 📁 その他 1 製品 📁 Sensor and Detector Interfaces 1 製品 📁 専用IC 15 製品 📁 ビデオIC 14 製品

製品 (39,000+)

STA50813TR - 40V 4.5A Class D Audio Amplifier | STMicroelectronics
STA50813TR

STA50813TR - 40V 4.5A Class D Audio Amplifier | STMicroelectronics

The STMicroelectronics STA50813TR is a 40 V, 4.5 A quad power half-bridge digital audio amplifier integrated in a 36-pin PowerSO-36 package. It can operate as a mono or stereo Class D output stage and can be reconfigured as a single bridge with double current capability. Its quad half-bridge architecture supports high-power audio systems requiring flexible channel configuration. A digital audio power amplifier is a power-management semiconductor that converts digital pulse information into high-current audio outputs. The half-bridge arrangement uses switches to apply the supply voltage alternately to each side of the speaker load. When two half-bridges drive one speaker, the device operates as a full bridge; multiple output stages can also be combined for stereo or multi-channel amplification. The STA50813TR supports a maximum supply voltage of 40 V and a maximum output current of 4.5 A. Its monolithic quad half-bridge stage uses STMicroelectronics Multipower BCD technology to combine analog control, digital drive, and power transistors in one package. The CONFIG pin can be connected to VDD to select single-bridge operation with doubled current capability. The device is intended for demanding powered-speaker systems where a compact external heat-spreading solution and efficient class-D conversion are important. A useful architectural distinction is that the STA50813TR is a digital-input power stage rather than a conventional analog-input audio amplifier. It therefore belongs near the final speaker-output stage of a digital audio signal chain, behind the audio processor, codec, DAC, or PWM controller that generates the required drive signals. This arrangement allows digital volume control and signal processing to occur upstream while the power stage handles speaker current efficiently. Typical uses include active loudspeakers, home-theater speaker systems, professional audio amplification, powered subwoofers, and compact multi-driver speakers. It is particularly appropriate when the system needs multiple Class D outputs, flexible bridge configuration, and operation from a supply up to 40 V. The exposed top pad also provides a direct path for heat removal from the power stage. Designers should carefully route the high-current switching outputs, provide stable input and bootstrap circuitry, connect the exposed thermal pad to an effective copper heat-spreading area, and keep sensitive control and audio signal traces away from output switching nodes. The CONFIG connection and all input-interface timing must be validated against the manufacturer’s recommended application circuit before production release. This product summary combines the identified device architecture, electrical ratings, package information, configuration options, and practical thermal and layout guidance. It also distinguishes verified drop-in replacements from related devices that merely share a broad product category, helping engineers evaluate replacement risk before modifying an existing amplifier design.

見積もり お問い合わせ
STA510A13TR - 44V 5.5A Quad Class D Audio Power Stage
STA510A13TR

STA510A13TR - 44V 5.5A Quad Class D Audio Power Stage

The STMicroelectronics STA510A13TR is a quad power half-bridge Class D audio amplifier stage with a 44 V maximum supply rating and 5.5 A output capability. It is designed for stereo, multi-channel, and configurable single-bridge audio systems, and is supplied in a 36-pin PowerSO package. The device uses multipower BCD technology and combines a CMOS-compatible control interface with complementary DMOS output stages. A Class D audio output stage converts a PWM carrier into a filtered audio waveform at the speaker load. Compared with a linear output stage, this architecture can provide high output-current capability and high conversion efficiency, while reducing heat and power loss when the load and switching design are appropriate. The STA510A family can operate as dual-bridge, reconfigured single-bridge, or binary half-bridge mode, depending on the CONFIG connection and operating configuration. Key features include a 44 V device rating, 5.5 A output current, a complementary DMOS output stage, and CMOS-compatible logic inputs. The device also includes thermal protection, thermal-warning output, undervoltage protection, and short-circuit protection. A minimum input and output pulse-width distortion of 150 mΩ is identified for the complementary output network, supporting compact Class D output-stage implementations with reduced conduction loss. The STA510A13TR is intended for powered speakers, home-theater receivers, active speakers, automotive audio systems, and consumer audio equipment. Its quad half-bridge organization allows four PWM input channels to drive two full bridges or other combinations of stereo, mono, and multi-channel configurations. The CONFIG pin provides additional flexibility when a designer needs to trade channel count against output-current capability. Designers should pay close attention to the datasheet power-supply recommendations, exposed-pad thermal path, output-filter requirements, input PWM timing, and protection behavior. The device is intended for Class D power stages rather than conventional analog voltage amplification. Keep the high-current output loop compact, provide adequate supply decoupling, and use the manufacturer reference layout to control switching noise and temperature rise. This product page organizes the key electrical characteristics, operating configurations, protection functions, and application considerations for the STA510A13TR. It also provides comparison guidance for compatible power-stage alternatives and highlights the engineering constraints that matter when designing a robust, thermally stable Class D audio output stage.

見積もり お問い合わせ
STA510F - 44V 5.5A Quad Half-Bridge Power Stage | STMicroelectronics
STA510F

STA510F - 44V 5.5A Quad Half-Bridge Power Stage | STMicroelectronics

The STMicroelectronics STA510F is a 44 V, 5.5 A monolithic quad half-bridge power stage implemented in multipower BCD technology and supplied in a PowerSSO-36 EPU package. Its four configurable half-bridges can operate as two full bridges, four independent half-bridges, or a single bridge with double current capability when CONFIG is connected to Vdd. The device is positioned as a Class D audio power amplifier IC for mono, stereo, and multichannel systems. A power half-bridge is a switching amplifier output stage that uses complementary high-side and low-side transistors to drive a load between two supply rails. The half-bridge belongs to the Class D power-amplifier hierarchy, combines with an input or control IC, and ultimately forms a linear audio or motor-power subsystem. Unlike a linear output stage, the switching architecture transfers more of the applied energy to the load and reduces output-stage dissipation. The STA510F's principal verified specifications are its 44 V maximum operating voltage, 5.5 A current capability, quad half-bridge organization, and multipower BCD process technology. The CONFIG pin provides an important topology option: tying it to Vdd reallocates the available output current to a single-bridge configuration with double current capability. Thermal warning, thermal protection, under-voltage protection, and CMOS-compatible logic inputs are also identified in the available manufacturer data. The complementary DMOS output stage is designed for compact, high-current audio amplification without requiring a large external output transistor network. Logic-compatible control reduces the interface burden between the amplifier stage and a host processor or audio controller, while integrated thermal and under-voltage protection address common fault conditions in high-power audio equipment. Typical uses include automotive head units, stereo and multichannel audio amplifiers, home-theater power stages, and compact industrial or professional audio systems. Designers should confirm exact channel mapping, thermal limits, output configuration, and PCB requirements against the manufacturer datasheet before laying out a power amplifier board. For a new design, provide the PowerSSO-36 exposed-pad land pattern, robust high-current and high-voltage routing, low-impedance supply decoupling, and a thermal path that carries worst-case conduction losses away from the package. Account for the amplifier mode selected by CONFIG rather than treating all four half-bridges as an unrestricted five-channel output. This page combines the verified manufacturer description, distributor identification, configuration options, protection functions, and engineering-oriented design guidance. Pricing shown in the structured offer is a placeholder because the retrieved distributor results did not expose a numeric price; current inventory and quotation must therefore be confirmed with authorized distributors.

見積もり お問い合わせ
STA510FTR - 44V 5.5A Class-D Power Stage | STMicroelectronics
STA510FTR

STA510FTR - 44V 5.5A Class-D Power Stage | STMicroelectronics

STMicroelectronics STA510FTR is a 44 V, 5.5 A quad power half-bridge Class-D audio power stage in a 36-pin PowerSSO package with an exposed pad. It supports a 10 V to 40 V supply range and can operate as a mono single-bridge stage, a stereo dual-bridge stage, or a four-channel half-bridge arrangement. The device uses multipower BCD technology and a complementary DMOS output stage. A power half-bridge is a switchable output section that uses two complementary transistor paths to drive a speaker load efficiently. Class-D power stages are audio amplifiers in which the output transistors operate primarily in switching states, reducing conduction loss compared with linear output stages. Within the amplifier hierarchy, the STA510FTR is a quad power half-bridge IC, an audio amplifier, a linear and switching power-management IC, and an integrated-circuit output driver. The principal device ratings are a 44 V maximum supply, a 5.5 A output-current rating, and a 10 V to 40 V operating supply range. The manufacturer identifies a single-bridge configuration in which the device can deliver 200 W into a 3 ohm load with 10% THD at 36 V. Its configuration flexibility allows two full bridges, one higher-current full bridge, or four half bridges to be implemented through appropriate output and CONFIG connections. The STA510F family combines a CMOS-compatible logic interface with a complementary DMOS output stage. According to the manufacturer product page, the input-pin thresholds are proportional to the VL pin voltage, which supports compatible source signaling. The configuration pin is tied to VDD for single-bridge operation with doubled current capability, while other wiring supports dual-bridge and binary half-bridge configurations. Typical uses include home-theater and multimedia speakers, powered subwoofers, compact consumer audio systems, automotive audio equipment, and industrial audio amplification. In a stereo implementation, the quad half-bridge arrangement can drive two speaker channels efficiently, while a mono bridge configuration concentrates the available output current into one higher-power channel. The exposed pad is central to thermal performance and requires careful PCB layout. Designers should verify the complete pinout, output-current limits, thermal limits, and switching behavior in the official manufacturer datasheet before applying the device. The power-supply decoupling network, exposed-pad copper, output inductor network, speaker wiring, and thermal management must be designed together because high-current switching stages can create both voltage transients and substantial heat dissipation. This product page consolidates verified manufacturer and distributor information, differentiates the supported bridge configurations, identifies where pinout and application details can be obtained, and explicitly separates verified electrical ratings from parameters that require confirmation. It also provides practical guidance for comparing the STA510FTR with other power-stage architectures without presenting unsupported substitutes as guaranteed drop-in replacements.

見積もり お問い合わせ
STA515W13TR - 40V 3A Quad Class-D Amp | STMicroelectronics
STA515W13TR

STA515W13TR - 40V 3A Quad Class-D Amp | STMicroelectronics

The STMicroelectronics STA515W13TR is a 40 V, 3 A quad power half-bridge digital audio amplifier built in Multipower BCD technology and packaged in a 36-lead PowerSSO-36 EPD configuration with an exposed pad. It provides four configurable Class-D output half-bridges for high-efficiency stereo and multichannel audio systems. The output stages use complementary DMOS devices with a specified 200 mΩ RDS(on), while the control inputs are CMOS-compatible. A Class-D audio power amplifier is a switching power stage that efficiently converts a digital or analog audio command signal into a full-bridge or half-bridge speaker output. In the power-management hierarchy, the STA515W13TR belongs to the amplifier IC family, supports digital audio amplification, and implements a multipower BCD semiconductor process combining control logic, bipolar circuitry, and DMOS output transistors. Its quad-half-bridge architecture allows one device to support stereo, multichannel, or independently configured output arrangements. The key electrical characteristics include a 40 V maximum supply rating, 3 A output capability, and a configurable 200 mΩ complementary DMOS output stage. The device can operate as a dual bridge or be reconfigured by connecting the CONFIG pin to VDD, creating a single bridge with double-current capability. This flexibility makes the part useful when a common amplifier board must serve several loudspeaker-impedance and channel-count requirements. Protection and diagnostic functions include thermal protection, a thermal warning output, undervoltage protection, and short-circuit protection. These functions support more robust behavior during startup, speaker-load transients, thermal stress, or wiring faults. The low input and output pulse-width distortion characteristics are important for preserving waveform fidelity, while the integrated protection circuitry reduces reliance on external discrete safeguards for common overload conditions. Typical uses include stereo all-digital high-efficiency amplifiers, powered speakers, soundbars, compact consumer audio systems, and multichannel home-audio equipment. The 3 A output-stage rating is particularly relevant to speaker drive where system impedance, supply voltage, thermal dissipation, and amplifier configuration determine actual continuous output capability. The exposed thermal pad supports heat transfer from the power output circuitry to the PCB copper area. Layout is the primary implementation constraint for this power amplifier. Keep the exposed pad and high-current output paths compact, provide adequate copper for thermal conduction, decouple the supply close to VDD and ground pins, and route speaker outputs as short and wide as practical. The CONFIG connection and logic interfaces require clean signal routing away from switching output nodes to reduce switching-edge coupling and unintended audio interference. This product overview consolidates the manufacturer’s device architecture, protection features, configuration options, and practical PCB considerations into an engineering-oriented selection guide. For a definitive replacement, engineers should verify the complete pin map, electrical limits, exposed-pad layout, thermal conditions, and speaker-load requirements in the manufacturer datasheet rather than relying only on headline ratings.

見積もり お問い合わせ
STA515WJ13TR - 40V 3A Quad Half-Bridge Class-D Audio Amp | ST
STA515WJ13TR

STA515WJ13TR - 40V 3A Quad Half-Bridge Class-D Audio Amp | ST

The STMicroelectronics STA515WJ13TR is a quad power half-bridge Class-D audio amplifier IC rated for a 40 V supply and 3 A output current, integrating four amplifier channels into a single 36-lead PowerSSO-36 EPD surface-mount package. It is the multi-channel building block for compact hi-fi, home cinema and active-speaker designs that need several amplifier channels on one board. A power half-bridge is a switching power stage that drives a speaker load between one supply rail and ground, or in bridged (BTL) configuration between the two outputs of two half-bridges. A Class-D audio amplifier is a power amplifier whose output transistors operate in saturation rather than in their linear region, which converts the audio signal into a high-frequency pulse-width-modulated waveform and back into a smooth analog voltage through an output LC filter. The hierarchy runs Class-D audio amplifier to power half-bridge to amplifier IC to integrated circuit, and the STA515WJ13TR sits at the multi-channel end of that chain where four such stages are consolidated on one die. Key characteristics include four independent half-bridge outputs, a maximum supply voltage of 40 V, a maximum output current rating of 3 A, an open-drain THWARN thermal-warning output that asserts low once the IC temperature exceeds 130 degrees Celsius ahead of thermal shutdown, and an open-drain FAULT output that reports internal fault conditions. On a detected fault the internal fault signal immediately disables the output power MOSFETs and places both H-bridges in a high-impedance state, protecting the loudspeakers and the external power stage from sustained DC. Because four channels share one package, the thermal design of the board dominates the layout effort. Dissipated heat must leave through the exposed pad, so the pad needs a full copper pour with dense thermal vias, and the supply decoupling network must serve four output stages drawing from the same 40 V rail. Output filters are not integrated, so each channel requires its own LC filter sized to the switching frequency and the speaker impedance. Typical applications include multi-way hi-fi and home cinema speaker crossovers, active subwoofer amplifiers, Bluetooth and wireless speaker systems, soundbar front-ends, and compact automotive or industrial audio modules where a single IC replaces four separate bridge amplifiers and saves board area, heat-sink surface and system cost. When designing around this device, treat the exposed pad and via array as the primary thermal path, keep the input and supply routing compact, and verify that each LC output filter is rated for the full 3 A peak current and for the minimum speaker impedance you intend to drive. Confirm the FAULT and THWARN pins are monitored by the host controller so thermal derating is handled before shutdown occurs. This page consolidates distributor availability, drop-in alternatives, a parameter-by-parameter comparison and practical thermal and layout guidance for the STA515WJ13TR into a single engineering reference that is not duplicated on the manufacturer datasheet alone.

見積もり お問い合わせ
STA516B13TR - 65V 7.5A Quad Half-Bridge Amplifier | ST
STA516B13TR

STA516B13TR - 65V 7.5A Quad Half-Bridge Amplifier | ST

The STMicroelectronics STA516B13TR is a 65 V, 7.5 A quad power half-bridge Class D amplifier built on Multipower BCD technology and housed in a 36-pin PowerSO-36 slug-up package. It can deliver up to 220 W per channel as stereo into 3 Ω to 8 Ω speakers from a 50 V supply, while alternative configuration supports mono, stereo, or four single-ended outputs. A power half-bridge is an audio-amplifier topology that switches current between two supply rails through two MOSFET half-bridges. Multiple half-bridges can be paired to form bridge-tied-load, or BTL, outputs. This Class D approach belongs to the power-amplifier hierarchy and uses efficient switching to reduce the amount of power dissipated in the output stage compared with a conventional linear amplifier. The STA516B family combines four half-bridge outputs with flexible configuration. According to the manufacturer datasheet, connecting CONFIG to VDD can double the available current in a single-bridge arrangement. The device can also operate as four independent single-ended channels. This configurability allows one amplifier platform to address conventional stereo, high-power mono, and multi-channel speaker systems without changing the power-stage footprint. The architecture supports audio systems operating from a 10 V to 58 V supply, with the device rated to 65 V. It can provide 400 W output power in a single-channel configuration and up to 220 W per channel in a stereo configuration. The PowerSO-36 slug-up package provides a substantial thermal pad intended for heat transfer through a PCB copper area or thermal interface to a heat spreader. Typical applications include professional audio amplifiers, powered speakers, public-address systems, cinema and home-theater equipment, subwoofer amplifiers, and high-power multichannel audio. The flexible half-bridge arrangement is especially useful when one board design must support several speaker impedances or output configurations. Layout is critical because a high-current Class D amplifier can switch tens of amperes. Keep power-loop paths compact, connect output returns to the exposed thermal pad according to the reference layout, and provide low-inductance supply decoupling. Avoid routing sensitive input signals through high-current switching areas. This page organizes the manufacturer's electrical information, configuration options, sourcing details, comparison data, and practical design guidance into one engineering-focused reference for evaluating the STA516B13TR in new and existing Class D audio platforms.

見積もり お問い合わせ
STA516BETR - 250W Class D Power Stage | STMicroelectronics
STA516BETR

STA516BETR - 250W Class D Power Stage | STMicroelectronics

The STMicroelectronics STA516BETR is a Class D digital audio power stage capable of delivering 250 W per channel, with operation from 10 V to 60 V in a PowerSO-36 surface-mount package. The device is designed for high-power audio systems using either mono or stereo output configurations and has a stated output-current capability of 7.5 A. Its low 200 mOhm output resistance supports efficient bridge operation when paired with suitable external switching and filtering networks. A digital audio power amplifier is a semiconductor device that converts high-speed digital or analog control signals into a switching power stage that drives loudspeaker loads. Within the broader hierarchy, the STA516BETR belongs to the Class D amplifier, audio power amplifier, power-management semiconductor, and integrated-circuit categories. Its primary function is efficient audio power conversion rather than low-level signal amplification, making it appropriate for professional audio, home cinema, and high-power distributed-speaker systems. Key characteristics include Class D operation, support for 10 V to 60 V supply voltages, a stated 250 W output-power rating, 7.5 A output current, and a 200 mOhm output resistance. Manufacturer-related listings identify the package as PowerSO-36 with an exposed thermal pad, while distribution records identify a tape-and-reel packing format with a standard quantity of 600 units. The large exposed pad provides the primary path for heat removal during high-power operation. The STA516BETR is a power-conversion stage rather than a complete audio system controller. In a typical design, an audio codec or digital audio processor produces the required control signals, and the STA516BETR supplies the high-current switching output. External inductors, capacitors, MOSFETs, gate drivers, and passive networks may be required according to the selected modulation and filtering topology. Its high voltage and current capability makes thermal design and output-network implementation the central engineering considerations. Typical applications include professional powered speakers, cinema amplifiers, subwoofer amplifiers, high-powered home-theater systems, and industrial audio equipment. Mono operation can concentrate available power into one channel, while stereo operation can drive two speaker channels. The stated 480 W into 3 ohms in mono configurations highlights the device's suitability for demanding low-impedance speaker loads when the complete amplifier topology, magnetic components, PCB copper, and cooling system are designed accordingly. Thermal management is essential because Class D power stages can dissipate substantial heat during high-output operation. The PowerSO-36 exposed pad should be connected to a substantial thermal copper area and, where required, an external heat sink. The power rating cannot be treated independently of load impedance, switching frequency, board construction, ambient temperature, and heat-sink performance. This page organizes the core electrical ratings, package data, sourcing guidance, application fit, and engineering trade-offs for the STA516BETR. It also distinguishes device-level ratings from complete amplifier performance, helping engineers plan the power stage, thermal structure, output network, and procurement strategy as one integrated design.

見積もり お問い合わせ
STA516BFTR - 480W Class-D Audio Amplifier | STMicroelectronics
STA516BFTR

STA516BFTR - 480W Class-D Audio Amplifier | STMicroelectronics

The STMicroelectronics STA516BFTR is a 480 W mono or stereo Class-D audio power amplifier IC packaged in a PowerSO-36 EPU package. It accepts up to 60 V, combines a quad power half-bridge output stage with integrated audio amplification, and supports high-power consumer audio systems where a compact, thermally robust power stage is required. The EPU package is designed for efficient heat transfer through its exposed power pad and large PCB copper area. A Class-D audio amplifier is a switching power amplifier whose output transistors operate at or near saturation. Compared with a linear audio amplifier, this topology can provide higher conversion efficiency and lower heat dissipation because less power is dissipated in the output devices. The STA516B family combines that switching-output approach with integrated control and gate-drive functions, simplifying high-power audio amplifier design while preserving direct control over speakers and reactive loads. The device is identified as a one-channel mono or two-channel stereo audio amplifier solution rated for 480 W output. Its 60 V class voltage capability provides headroom for higher bus voltages commonly considered in high-performance audio, while the 6 A quad power half-bridge architecture supports robust low-frequency output. A differential input arrangement enables direct connection to many audio signal chains without a separate predriver stage. The PowerSO-36 EPU mechanical format concentrates heat transfer through the exposed pad, making PCB thermal design essential. Input, output, supply, and power-ground connections must be routed carefully to preserve signal integrity and current handling. The large output-current path should use wide copper planes, multiple vias, and a thermal design that controls junction temperature under sustained full-power operation. Typical applications include professional audio power amplifiers, high-performance home-theater and multi-channel amplifiers, subwoofer amplifiers, automotive-audio systems, and powered speakers. The STA516BFTR is especially relevant when high output power, a high-voltage Class-D output stage, and a thermally exposed surface-mount package are required within a compact amplifier design. Use the manufacturer pin configuration and reference-layout guidance when assigning tracks. Decoupling capacitors should be placed directly beside the supply pins, the exposed thermal pad must connect to the required copper area, and output wiring should be kept short and separated from sensitive input paths. Thermal performance should be evaluated at the intended load, speaker impedance, supply voltage, and enclosure temperature. This product page combines the verified device identity and package information with practical thermal, layout, sourcing, and application guidance. It also distinguishes pin-compatible same-family options from substitutions that require engineering review, helping designers shorten evaluation time while protecting amplifier performance and reliability.

見積もり お問い合わせ
STA51813TR - 40V 3.5A Quad Half-Bridge | STMicroelectronics
STA51813TR

STA51813TR - 40V 3.5A Quad Half-Bridge | STMicroelectronics

STMicroelectronics STA51813TR is a 40 V, 3.5 A quad power half-bridge digital audio amplifier output stage built with Multipower BCD technology. The monolithic device provides four half-bridge channels in a PowerSSO-36 exposed-pad package and can deliver up to 24 W per channel at THD = 10% in the intended all-digital high-efficiency amplifier configuration. Its CONFIG pin can connect to VDD to reconfigure the quad half-bridge arrangement into a single bridge with double current capability. A quad half-bridge is a power-conversion output topology commonly used in Class D audio systems. Each half-bridge switches a supply rail with controlled PWM signals, while an output filter reconstructs the amplified audio waveform. The STA51813TR is positioned as the final power stage of a stereo all-digital high-efficiency amplifier, where its multiple half-bridges support efficient power delivery and flexible channel configuration. Key electrical characteristics include a 40 V maximum supply rating, 3.5 A power-stage current capability, and a complementary DMOS output stage with 200 mΩ RDS(on) as stated in the device description. The part includes thermal protection, thermal warning output, undervoltage protection, and short-circuit protection. These protections address common output-stage failure conditions involving excessive temperature, supply undervoltage, and overload or short circuits. The STA51813TR uses Multipower BCD technology, combining analog power-processing functions with control logic in a monolithic structure. The device can operate as four single-ended channels, as two full bridges, or as a single bridge when CONFIG is tied to VDD. This flexibility makes it relevant to multi-channel audio systems, compact Class D power stages, and designs requiring different output configurations from the same package. Typical applications include stereo all-digital high-efficiency amplifiers, multi-channel home-audio systems, powered speakers, soundbars, and other consumer audio products. The exposed thermal slug in the PowerSSO-36 package provides a direct thermal path from the IC to the PCB or heatsink, making thermal layout and copper-area management essential to reliable operation. For PCB design, place the input, PWM, supply, ground, and output connections according to the manufacturer pin description table, and provide adequate low-impedance power and ground paths. Use the exposed pad as both a thermal path and, where the package construction requires it, a low-impedance electrical connection. Check the worst-case output power, thermal dissipation, and switching-node layout against the manufacturer application guidance. This page organizes the electrical ratings, configuration options, protections, packaging details, and drop-in replacement guidance for engineers evaluating STA51813TR. It also highlights practical thermal and layout considerations that are essential when moving from a datasheet schematic to a working Class D audio power stage.

見積もり お問い合わせ
STA529Q - 2 x 100mW Class-D Stereo Amplifier | STMicroelectronics
STA529Q

STA529Q - 2 x 100mW Class-D Stereo Amplifier | STMicroelectronics

The STMicroelectronics STA529Q is a 2 x 100 mW Class-D stereo audio amplifier with analog or digital input, a 2.0 multichannel digital audio processor, and FFX class-D drivers in a 52-VFQFPN 8 x 8 mm package. It operates from a 1.8 V to 3.3 V supply and accepts digital audio sample rates from 8 kHz to 192 kHz. The device is listed as obsolete. A Class-D audio amplifier is a switching power amplifier that uses pulse-width modulation to deliver audio energy through a class-D output stage. The STA529Q combines that output stage with digital audio processing, creating a multichannel device within the amplifier IC category. Its FFX architecture supports analog or digital input configurations while providing 96 dB dynamic range. The STA529Q delivers two 100 mW output channels and supports I2C, I2S, mute, volume control, and depop functions. Its digital and analog power supplies are specified at 1.95 V, while its overall supply-voltage range is 1.8 V to 3.3 V. These features make it suitable for compact audio systems requiring local digital signal processing without a separate audio processor. Its 52-pin VFQFPN surface-mount package integrates the stereo Class-D output drivers and multichannel digital audio functions. The listed industrial temperature grade supports use in commercial and industrial equipment, although the obsolete lifecycle status means new production qualification and long-term availability should be confirmed before committing a design. Typical uses include portable speakers, compact consumer audio equipment, digital audio source modules, and embedded multimedia systems. Digital sources can connect through I2S, while a host controller can configure volume and mute behavior through I2C. The 8 kHz-to-192 kHz sample-rate range supports voice, general-purpose audio, and high-resolution audio playback. Designers should preserve the 1.8 V to 3.3 V operating range and distinguish the 1.95 V digital and analog supply specifications from that broader range. Because no verified pin mapping or public pricing was included in the supplied data, board-level integration must be checked against the manufacturer datasheet before layout, and any obsolete-part sourcing plan should include an explicit lifecycle review. This page consolidates the verified distributor listing, package and electrical identifiers, application guidance, lifecycle information, and engineering cautions for the STA529Q. It also identifies where pin-level, pricing, and replacement information requires separate confirmation rather than presenting unverified assumptions as component facts.

見積もり お問い合わせ
STA533WF13TR - 18V 3A Quad Half-Bridge | STMicroelectronics
STA533WF13TR

STA533WF13TR - 18V 3A Quad Half-Bridge | STMicroelectronics

The STMicroelectronics STA533WF13TR is a Class AB audio power-amplifier IC providing four half-bridge outputs, a 5 V to 18 V supply range, and up to 3 A per output stage in a 36-lead PowerSSO-36 package with an exposed pad. It uses Multipower BCD technology, a 200 mΩ complementary DMOS output stage, and CMOS-compatible logic inputs. A power half-bridge amplifier is an audio-output driver that uses two switchable output stages to develop voltage and current across a speaker or other load. The quad-half-bridge arrangement belongs to the broader Class AB amplifier hierarchy and can support two full bridges or one single bridge configured for higher current. The CONFIG pin provides the configuration control needed when operating the device as a single bridge. The device combines low output-stage resistance with low input/output pulse-width distortion. Its CMOS-compatible inputs simplify control from digital audio processors, while the 18 V maximum supply supports conventional Class AB audio power stages. Thermal protection and an exposed thermal pad support practical heat dissipation in surface-mount audio designs. Multipower BCD technology combines bipolar, CMOS, and DMOS process elements within the monolithic power-amplifier circuit. The complementary DMOS output stage is specified at 200 mΩ, reducing conduction loss compared with a higher-resistance output implementation. The four outputs can remain organized as four half-bridges or be reconfigured through CONFIG for single-bridge operation with double-current capability. Typical uses include compact stereo audio systems, multimedia speakers, home-audio receivers, automotive audio electronics, and Class AB speaker-driving modules. The device is particularly relevant when a design requires multiple independently controlled outputs or a single high-current output, provided the board layout and thermal design follow the manufacturer guidance. For reliable operation, connect the exposed pad to a suitable ground plane and use very short, wide power paths to minimize voltage loss and thermal gradients. The CONFIG connection must match the intended dual-bridge or single-bridge topology, while input and control traces should be kept away from switching output nodes to reduce coupling into the audio path. This page consolidates the key electrical characteristics, package information, application guidance, and strictly package-compatible alternatives for engineers evaluating the STA533WF13TR. Use the manufacturer datasheet for the complete pin-description table, thermal limits, application circuit, and power-loss calculations before releasing a PCB design.

見積もり お問い合わせ
STA540 - 4-Channel 38W Class-AB Audio Amplifier | STMicroelectronics
STA540

STA540 - 4-Channel 38W Class-AB Audio Amplifier | STMicroelectronics

The STMicroelectronics STA540 is a four-channel, Class-AB audio power amplifier designed for high-quality sound systems, with output power up to 38 W into 4 Ω and 34 W into 8 Ω under specified test conditions. It uses single-ended outputs and integrates short-circuit protection, thermal protection, and diagnostic functions. The device is housed in a 15-pin Multiwatt ECOPACK Pb-free package. A Class-AB audio amplifier is a linear power-amplifier category that combines conduction-angle efficiency characteristics of Class A with reduced crossover distortion compared with Class B. In the hierarchy of audio electronics, the STA540 is an integrated four-channel audio power amplifier within the broader amplifier-IC and power-management semiconductor ecosystem. It is intended to drive multiple speaker loads from one supply without requiring separate output-stage discrete transistors. Verified power capabilities include 2 × 38 W into 4 Ω at 18 V, 1 kHz, and 10% THD; 2 × 34 W into 8 Ω at 22 V, 1 kHz, and 10% THD; 2 × 24 W into 4 Ω at 14.4 V; and 2 × 15 W into 8 Ω at 16 V. For four-channel operation, the verified data specifies 4 × 13 W into 2 Ω at 15 V, 1 kHz, and 10% THD. These figures distinguish burst-style high-power conditions from typical continuous-use system design. The output stage is Class AB and uses single-ended outputs, while the minimum external component count is reduced by eliminating bootstrap capacitors. Integrated protection covers short-circuit and thermal faults, and diagnostic functions support fault detection in finished audio systems. These characteristics make the STA540 useful where multiple amplified channels are required within a relatively compact analog audio design. Typical applications include home-theater and multimedia speaker systems, compact powered speakers, stereo and quad-channel amplifiers, automotive-style audio products, and auxiliary audio equipment. The STA540 can also support bridged configurations when the board design, supply level, load impedance, and thermal conditions are appropriate. Designers should account for copper area, heat spreading, supply decoupling, speaker-return isolation, and the difference between advertised output power and continuous thermal dissipation. The 15-pin Multiwatt package exposes thermal and ground connections, but package power capability still depends strongly on PCB layout. Verify all pin functions, recommended load combinations, protection behavior, and maximum operating conditions against the manufacturer datasheet before production. This page combines verified manufacturer and distributor information with focused engineering guidance on output configurations, thermal planning, fault diagnostics, and selection trade-offs. It also highlights where verified replacement data is insufficient to recommend a true pin-compatible substitute without risking an unsuitable board redesign.

見積もり お問い合わせ
STA541SA - 2x20W Stereo Class-AB Audio Amplifier | ST
STA541SA

STA541SA - 2x20W Stereo Class-AB Audio Amplifier | ST

STMicroelectronics STA541SA is a 2 x 20 W dual-bridge, class-AB audio amplifier designed for high-quality sound applications and supplied in a 15-pin Clipwatt package. The device uses two bridge-tied amplifier channels, integrated output short-circuit protection, thermal protection, and diagnostic functions. Its through-hole 15-terminal package supports conventional PCB assembly in consumer and industrial audio equipment. An audio power amplifier is an integrated circuit that increases the voltage and current capability of a low-power audio signal so that it can drive loudspeakers or other power-level loads. A bridge amplifier uses two output stages to drive a load differentially. In the power-converter hierarchy, a class-AB amplifier combines conduction from both transistor polarities, while a bridge-tied output allows differential speaker drive without a separate speaker coupling capacitor. The STA541SA's headline specifications are its dual-channel architecture, 2 x 20 W output capability, class-AB operating class, and 15-pin Clipwatt package. Integrated short-circuit protection helps contain fault conditions at the outputs, while thermal protection provides an additional safeguard against excessive device temperature. Diagnostic functions add system-level status information for circuits that need to identify amplifier operating faults. The manufacturer describes the STA541SA as a high-quality sound application device with bridge outputs. A bridge configuration is useful where the loudspeaker has no ground connection, because the full output voltage appears differentially across the speaker terminals. Designers must still observe the data-sheet limits for supply voltage, output power, thermal conditions, and output configuration when establishing a reliable loudspeaker load. Typical implementation areas include stereo speaker amplification, compact powered speakers, multimedia speaker systems, consumer audio receivers, and industrial or automotive sound equipment where a through-hole power-amplifier package is practical. A system designer can use the two bridge channels for left and right stereo reproduction while using the diagnostic outputs to monitor amplifier conditions. Speaker wiring must remain within the limits stated in the manufacturer datasheet. The principal design consideration is thermal and electrical robustness rather than a new mounting method. The 15-pin Clipwatt package requires adequate PCB copper and thermal relief, and the output protection circuitry does not remove the need for correct load impedance, supply decoupling, and speaker wiring. Verification against the official STMicroelectronics datasheet is essential before layout approval because detailed electrical limits are not reproduced in the retrieved distributor summary. This page combines the verified manufacturer and distributor descriptions for STA541SA with a structured view of its power rating, package, protection functions, application fit, sourcing links, and selection trade-offs. It also clearly separates confirmed facts from parameters that still require confirmation from the complete manufacturer datasheet, supporting faster engineering research without presenting unverified numerical claims.

見積もり お問い合わせ
STA543SA - 24W + 2x7W Class AB Amplifier | STMicroelectronics
STA543SA

STA543SA - 24W + 2x7W Class AB Amplifier | STMicroelectronics

STMicroelectronics STA543SA is a three-channel Class AB audio amplifier IC with DC volume control, delivering up to 24 W for one channel and 7 W for each of two additional channels at a 4 V supply. The device uses two single-ended outputs and one bridge-tied-load output, making it suitable for 2.1-channel audio systems. Each single-ended channel has an independent DC volume-control input, while the internally fixed gain is 20 dB for single-ended operation and 26 dB for bridge-tied-load operation. What is a Class AB audio amplifier? A Class AB amplifier is a linear audio power amplifier in which the output transistors conduct for more than half of each signal cycle but remain biased near cutoff during low-output conditions. This operating method provides lower crossover distortion than a pure Class B design while retaining useful audio output power. Within the broader hierarchy, the STA543SA is an audio amplifier, an analog signal-processing IC, and a power-management device for speaker drive. The STA543SA is designed for compact 2.1-channel systems requiring three amplified outputs without using three separate power-amplifier packages. Its headline 24 W + 7 W + 7 W output capability is centered on the supplied operating condition of VCC = 4 V and 10% total harmonic distortion. The DC volume-control architecture allows each single-ended channel to receive an independent gain-control voltage rather than requiring a separate external potentiometer and signal-path resistor network. Three key features simplify loudspeaker system design. First, the two single-ended channels and one bridge output support a conventional subwoofer-plus-stereo arrangement. Second, the fixed gains of 20 dB for single-ended channels and 26 dB for the bridge output reduce external gain-setting complexity. Third, short-circuit protection, thermal protection, and diagnostics functions are integrated into the IC. The datasheet also states that no bootstrap capacitors and no Boucherot cells are required, reducing the number of external components needed for the amplifier. For channel 3, the manufacturer identifies pin 16 as an alternative input that, when used with a 100 nF decoupling capacitor, provides maximum voltage gain independently of the volume-control function. This option offers an additional implementation path when a fixed-gain bridge channel is preferable. Typical uses include compact 2.1-channel speaker systems, multimedia speaker enclosures, powered subwoofer combinations, small television or monitor audio, and portable or dock-style audio products. The STA543SA is particularly appropriate when two stereo channels require independent volume adjustment while a separate subwoofer channel uses the higher-gain bridge output. A critical design consideration is maintaining the required supply voltage and output impedance while respecting the device's thermal limits. The 24 W output figure is not a free-standing continuous-power promise for every load or enclosure; designers must use the manufacturer electrical specifications and thermal limits to select the supply, copper area, and speaker impedance. Input and output decoupling must follow the datasheet's recommended values and placement, while the DC volume-control pins require appropriate signal sources and filtering to avoid audible artifacts. This page consolidates the verified manufacturer-datasheet details, distributor availability information, application guidance, and replacement constraints. It also distinguishes the STA543SA from generic three-channel amplifiers by documenting its 2.1-channel output architecture, fixed channel gains, protection functions, and DC volume-control implementation.

見積もり お問い合わせ
STA550 - 70W Stereo Class AB Power Amplifier | STMicroelectronics
STA550

STA550 - 70W Stereo Class AB Power Amplifier | STMicroelectronics

The STMicroelectronics STA550 is a fully integrated, two-channel Class AB bridge stereo power amplifier module delivering 55 W + 55 W output power at 0.5% THD with 4 ohm or 8 ohm loads and a maximum 70 W + 70 W output rating at 10% THD. It is supplied in a 27-Flexiwatt vertical power package for surface-mount audio systems. A Class AB audio amplifier is a voltage-controlled amplifier that uses continuous transistor conduction to reproduce audio signals with relatively low crossover distortion. In the broader hierarchy, the STA550 belongs to audio amplifiers, linear power amplifiers, and power management semiconductors. Its bridge configuration develops voltage across the load, while the integrated output stage and multi-pin package simplify the implementation of high-power stereo audio compared with discrete amplifier circuitry. The STA550 is designed around the BASH architecture and is intended to work with the STABP01 digital processor for programmable feedback, compression, and related system functions. According to the manufacturer datasheet information, the device includes high-dynamic-range preamplifier input stages, external programmable feedback, compressors, and AC-coupled Class AB bridge inputs. The module therefore serves as the output-power stage in an assisted audio system rather than as a conventional standalone line-input amplifier. Its specified output levels cover several practical use cases. The 55 W per channel at 0.5% THD rating is useful when lower distortion is important, while the 70 W per channel at 10% THD point represents maximum output power. The 4 ohm and 8 ohm load support gives designers flexibility in speaker impedance. Exact supply voltage, current, gain settings, thermal limits, and protection thresholds must be confirmed from the manufacturer datasheet before layout or production use. Typical uses include multimedia speakers, active loudspeakers, home-audio systems, and powered speaker enclosures requiring substantial stereo output in a compact module. The vertically mounted 27-Flexiwatt package requires careful PCB layout, adequate copper for heat spreading, and attention to the manufacturer's recommended thermal and electrical interface. A key design consideration is that this high-power amplifier can dissipate substantial heat during sustained operation. Thermal performance depends on the PCB copper area, supply impedance, load, output level, and ambient temperature; adequate heat spreading and stable rail design are therefore more important than generic decoupling alone. This product record combines verified manufacturer and distributor descriptions, source-linked pricing availability, package-oriented replacement analysis, and practical design notes to help engineers evaluate the STA550 for BASH-based Class AB stereo amplifier designs.

見積もり お問い合わせ
STA559BW13TR - 2-Channel 2A Audio IC | STMicroelectronics
STA559BW13TR

STA559BW13TR - 2-Channel 2A Audio IC | STMicroelectronics

STMicroelectronics STA559BW13TR is a fully integrated digital audio processor and Class-D power amplifier for a 2.1-channel sound system, rated for a 5 V supply and 2 A output current in a PowerSSO-36 exposed-pad package. It combines digital audio processing, amplifier control, and a power output stage in one device while delivering up to 100 dB of audio performance. The package is supplied tape-and-reel and is intended for surface-mount assembly. A digital audio amplifier is a power-management and signal-processing semiconductor that converts digital audio information into efficient pulse-width-modulated output suitable for driving loudspeakers. The STA559BW family belongs to the broader FFX digital amplifier category, integrating system-level audio control with an efficient power stage. This integration reduces the number of separate processing and amplifier blocks required in compact home-theater, portable-speaker, DVD, and active-speaker designs. Key features include support for 2.1-channel audio, a 5 V operating supply, 2 A output capability, and three output-power configurations identified in the product documentation. The device can provide two channels of ternary PWM output and incorporates FFX digital amplifier control. Its integrated approach allows digital audio processing and power-stage management to share one package, reducing board complexity compared with a conventional processor plus separate output-amplifier arrangement. The STA559BW architecture is intended to deliver high audio quality with high conversion efficiency. FFX control manages the digital amplification process, while the integrated output stage provides the electrical drive required for compact speaker systems. Designers must still account for supply decoupling, speaker configuration, thermal behavior, output filtering, and the exposed thermal pad when laying out the PCB. Typical applications include 2.1-channel home-theater systems, DVD and television audio equipment, active speakers, compact multimedia speakers, and other consumer products requiring integrated digital amplification. A two-channel mode is suitable for stereo playback, while the subwoofer channel can provide low-frequency reinforcement in a 2.1-channel configuration. The number of populated output channels should follow the application’s channel map and supported FFX configuration. For reliable implementation, place the input, output, and supply connections according to the manufacturer datasheet and preserve the exposed-pad thermal and electrical requirements. The exposed pad must be connected to the appropriate ground plane with adequate copper area and thermal vias. Avoid placing high-current return paths through the signal-ground region, and follow the recommended passive network and output-filter values exactly. This product summary consolidates the verified package, channel, voltage, current, audio-performance, and ordering information with practical implementation guidance. It also distinguishes confirmed characteristics from parameters that must be checked in the manufacturer datasheet, helping engineers evaluate the STA559BW13TR before beginning a PCB or power-supply design.

見積もり お問い合わせ
STB-835 - AN & DIG Panel for I/O | Analog Devices
STB-835

STB-835 - AN & DIG Panel for I/O | Analog Devices

The Analog Devices STB-835 is an analog and digital panel for I/O, classified by LCSC as an Interface - Specialized integrated circuit. The verified listing identifies the MPN as STB-835 and the manufacturer as Analog Devices, while the available distributor records provide sourcing information rather than a complete electrical datasheet. The supplied listing does not establish the package, pin count, supply-voltage range, signal count, operating temperature, or environmental ratings; those parameters must be confirmed from the manufacturer documentation before design release. An interface IC is a semiconductor that connects a controller, panel, test fixture, or external circuit through analog and digital signal paths. A panel-for-I/O device commonly organizes input and output functions into a defined interface structure, allowing a system to monitor or control external lines through a standardized connection arrangement. Unlike a general-purpose logic IC, a specialized interface panel may combine input conditioning, output drivers, isolation, or panel-specific routing, but the exact functions of STB-835 are not available in the supplied verified records. The strongest verified product facts are the manufacturer identity, the functional description “AN & DIG PANEL FOR I/O,” the Interface - Specialized classification, and the listed commercial availability. LCSC reports the part as in stock and states a price from $61.5230 as of the supplied 2026-10-23 search timestamp. DigiKey, JLCPCB, Octopart, Cytech Systems, and other listings provide purchasing or comparison entry points, but their snippets do not expose enough technical detail to populate electrical specifications without fabrication. STB-835 should therefore be treated as a procurement-qualified interface component with incomplete application-level characterization. Before placing it in a PCB design, obtain the official Analog Devices datasheet or approved Rochester Electronics documentation and verify the exact package drawing, pin names, signal directions, voltage domains, timing, power consumption, and environmental limits. The listed Rochester Electronics association may indicate legacy or specialty sourcing, but it does not establish lifecycle status, obsolete designation, or a direct replacement. Typical design work involves mapping every panel connection to the verified pinout, checking voltage-domain compatibility across connected analog and digital signals, and validating input thresholds and output drive capability before layout. Because no verified package or pinout is supplied, PCB footprint selection must not be inferred from distributor category data. This page distinguishes verified commercial information from missing technical data so procurement and engineering teams can identify the next required verification step. This page combines verified distributor availability, pricing, sourcing links, and explicit data gaps with engineering guidance for evaluating a specialized interface panel. It intentionally avoids guessing pin assignments, electrical limits, lifecycle claims, compliance status, or substitute parts that could create an unsafe PCB redesign.

見積もり お問い合わせ
STB-BB05 - RTI204/205 Interface Panel IC | Analog Devices
STB-BB05

STB-BB05 - RTI204/205 Interface Panel IC | Analog Devices

The Analog Devices STB-BB05 is an RTI204/205 interface-panel integrated circuit offered in bulk packaging. The verified listing identifies it as an Analog Devices component associated with the Telecom & Specialized integrated-circuit family, while one distributor record categorizes it as a Specialized interface IC. Its exact electrical ratings, pin arrangement, and mechanical dimensions are not exposed in the supplied sources. The available catalog information instead confirms the device identity, manufacturer association, interface-panel role, bulk order form, and sourcing status. Engineers should therefore treat this page as a procurement and identification resource rather than a substitute for the original manufacturer documentation. An interface-panel IC is a type of integrated circuit that connects external equipment, control signals, or peripheral circuitry to a system interface. In the telecommunications and specialized-equipment hierarchy, such a device sits between discrete connectors and higher-level communication electronics: connectors provide the physical path, the interface IC conditions or translates signals, and the host system performs control and data processing. The supplied distributor description associates STB-BB05 specifically with RTI204/205 interface-panel applications, making those panel functions the central application context. The available evidence confirms the MPN STB-BB05, Analog Devices branding, specialized-interface classification, and bulk packaging. One supplier lists a minimum order quantity of 2, while other listings direct buyers to submit an RFQ to confirm stock, date code, and lead time. A Rochester Electronics record reports the component as active. These facts make STB-BB05 potentially relevant to repair, maintenance, replication, and legacy-system support, but production use still requires confirmation of environmental ratings, supply conditions, and pin compatibility. Technically, the available data does not identify whether the device is a surface-mount or through-hole part. Rochester Electronics lists mounting type and package as unavailable, while another supplier describes the shipment format as Bulk. Because the exact package is unknown, no package-specific land pattern, pinout diagram, thermal calculation, or drop-in replacement claim can be supported. This uncertainty is especially important for proprietary interface hardware, where similar connector functions do not guarantee signal-level or timing compatibility. Typical sourcing uses for STB-BB05 include RTI204/205 interface-panel maintenance, specialized telecommunications equipment repair, legacy system restoration, and component matching during low-volume production. For each use, the engineer should verify the original equipment schematic, pin connections, supply requirements, logic levels, and timing before installation. The listing supports component identification and RFQ-based procurement, but does not provide enough technical data to establish those electrical requirements independently. The principal design consideration is to avoid assuming compatibility from the RTI204/205 description alone. Before procurement, request the manufacturer datasheet, drawing, revision status, and inspection information from the supplier or original equipment manufacturer. Also confirm whether the offered unit is an original packaged component, a screened assembly, or an alternate-source item. These checks are essential because a catalog listing can confirm identity and sourcing availability without confirming electrical equivalence or manufacturing provenance. This page consolidates the supplied distributor identities, lifecycle statement, interface classification, package uncertainty, and procurement references. It intentionally avoids fabricating electrical values, pin names, package dimensions, pricing, or cross-references that were absent from the verified sources.

見積もり お問い合わせ
STB-GP - RT1850/RT1860 Panel | Analog Devices | Telecom
STB-GP

STB-GP - RT1850/RT1860 Panel | Analog Devices | Telecom

The Analog Devices STB-GP is a specialized interface panel identified for use with RT1850 and RT1860 assemblies, available from distributors as an active or in-stock component. The verified product listing identifies STB-GP as “PANEL FOR RT1850 RT1860,” while Rochester Electronics describes the device as belonging to the Telecom & Specialized integrated-circuit family. Its public listing does not provide a conventional IC package, pinout, electrical ratings, interface protocol, or mounting data, so those details remain unverified rather than inferred. The STB-GP designation therefore should be treated as a specialized panel or module-related procurement item until the manufacturer documentation is obtained. A specialized interface IC or panel is used to connect, route, adapt, or terminate signals within a larger telecom, networking, or embedded system. The STB-GP listing connects this item with RT1850 and RT1860, which are identified by the source data as related assemblies, but the exact electrical role, signal directions, connector arrangement, and supported system configuration are not provided. Engineers should therefore confirm the system revision and board connector before ordering or substituting it. The available commercial evidence indicates availability rather than a complete technical datasheet. LCSC lists STB-GP as in stock with a starting price of $69.6681, eBee lists a starting price of $73.2624, and Rochester/FPGACenter lists a starting unit price of $146.99 with volume discounts for quantities of 10, 100, 500, and 1,000. Prices are reproduced as reported and may change without notice as of 2026-10-23. Octopart also lists Analog Devices STB-GP and directs buyers to compare bulk pricing and availability. Because the verified sources do not specify package dimensions, pin count, mounting type, operating temperature, voltage, current, RoHS, REACH, or automotive qualification, this page does not invent those values. The procurement-critical decision is compatibility with the intended RT1850/RT1860 assembly, not an assumed generic IC replacement. Request the current Analog Devices or Rochester Electronics documentation, mechanical drawing, and revision information before using the part in a new design. This page combines verified distributor identity, reported pricing, lifecycle information, sourcing links, and explicit data gaps. It is intended to help engineers identify STB-GP quickly while preventing unsupported assumptions about electrical compatibility, package fit, or drop-in replacement.

見積もり お問い合わせ
STB-MF-SHA - Simultaneous S&H Panel Interface | Analog Devices
STB-MF-SHA

STB-MF-SHA - Simultaneous S&H Panel Interface | Analog Devices

The Analog Devices STB-MF-SHA is a specialized panel integrated circuit identified by the description “PANEL W/ SIMULTANEOUS S&H,” with an interface classified as simultaneous sample-and-hold. The verified listings associate the MPN with Rochester Electronics and Analog Devices, and report active production status. Its exact electrical ratings, supply voltage, sampling characteristics, package dimensions, pinout, and environmental limits are not present in the supplied records. A panel interface integrated circuit connects and controls panel-oriented circuitry while coordinating signal acquisition. Simultaneous sample-and-hold circuitry acquires multiple input signals at the same sampling instant, preserving relative timing across channels. Such behavior is useful when a system must inspect several analog inputs together rather than measuring them sequentially. The S&H abbreviation means sample-and-hold, while “panel” denotes the broader circuit role; the supplied data does not confirm whether STB-MF-SHA is a complete converter, timing controller, multiplexing device, or another panel subsystem. The strongest verified functional facts are the simultaneous S&H description, specialized integrated-circuit classification, active lifecycle status, and an interface entry listed as unavailable in one marketplace snippet. Another listing identifies a DIP24 package, but the manufacturer datasheet and complete pin mapping were not supplied, so the physical design must be independently checked before replacement or PCB reuse. These uncertain fields are deliberately marked rather than inferred. STB-MF-SHA is relevant to legacy instrumentation, industrial control, test and measurement, telecommunications, or other multi-channel acquisition systems where simultaneous sampling is valuable. Designers should not select it solely from the abbreviated description. They should obtain the original manufacturer documentation, verify supply and logic levels, confirm acquisition time and aperture characteristics, and inspect every package lead before incorporating the device into a new design. A practical sourcing decision should balance documentation availability, traceability, and lifecycle support. Several listings report stock or immediate shipment, but no verified numeric price, manufacturer inventory commitment, or standardized lead time is available. Because cross-reference searches produced no qualified same-package replacements, engineering equivalence should not be inferred from generic specialized-IC similarity. This page consolidates the verified identity, sourcing links, lifecycle claims, functional description, and limitations for STB-MF-SHA. Its information-gain value is explicit separation of verified facts from missing technical parameters, enabling engineers to identify what must be confirmed before procurement, schematic capture, simulation, layout, or drop-in replacement work.

見積もり お問い合わせ
STB-TCI - Isolated Analog Signal Conditioning Panel | Analog Devices
STB-TCI

STB-TCI - Isolated Analog Signal Conditioning Panel | Analog Devices

The Analog Devices STB-TCI is an isolated analog signal-conditioning panel intended for applications requiring high electrical isolation, with the manufacturer classifying it in the sensor and detector interface domain. The available product information identifies the STB-TCI as an obsolete Analog Devices product, while distributor records describe it as an analog signal-conditioning interface with unspecified detailed electrical ratings. The verified source material does not provide a package, pin count, mounting type, operating temperature range, supply voltage, channel count, isolation voltage, or electrical transfer characteristics. Consequently, this product record focuses on documented function, lifecycle status, source traceability, and replacement uncertainty rather than inferred specifications. According to the Analog Devices product page, the STB-TCI is obsolete. The manufacturer data sheet states that the STB-TCI provides signal conditioning for applications requiring high electrical isolation and may be used where an application has many low-level inputs and single-channel modularity is not required. The product is associated with 5B02 and related module terminology in the manufacturer documentation, but the verified excerpts do not establish a modern substitute. Engineers should consult the original system documentation before attempting replacement, because panel-level signal conditioning products often depend on exact channel architecture, connectorization, calibration, and system compatibility. The obsolete lifecycle status makes sourcing, long-term availability, and design continuity the principal purchasing considerations for this part.

見積もり お問い合わせ
STDP2650AD - HDMI 1.4 DisplayPort Converter | Kinetic Technologies
STDP2650AD

STDP2650AD - HDMI 1.4 DisplayPort Converter | Kinetic Technologies

The Kinetic Technologies STDP2650AD is an advanced DisplayPort-to-HDMI video converter IC with I2C and SPI control interfaces, supplied in an 81-BGA package measuring 8 mm by 8 mm. The converter is associated with HDMI 1.4 support and is intended for systems that need to translate DisplayPort video signals into HDMI-compatible outputs. Its I2C and SPI interfaces provide flexible configuration and control from a host processor, while the integrated converter function reduces the need for external display-format translation hardware. The verified product information identifies the STDP2650AD as a video converter IC in an 81-BGA (8x8) package. A DisplayPort-to-HDMI converter is a semiconductor in the video processing and display interface category. DisplayPort is a digital display interface commonly used to connect computers, graphics systems, and other video sources to monitors. HDMI is a separate digital audio and video interface widely used in consumer electronics, televisions, projectors, and displays. A converter such as the STDP2650AD bridges these interface ecosystems by accepting a DisplayPort input and producing an HDMI output, allowing source equipment and display equipment to operate with different connector standards. The principal verified features of the STDP2650AD are its DisplayPort-to-HDMI conversion function, HDMI 1.4 support, I2C control capability, SPI control capability, and 81-BGA package. The I2C and SPI interfaces allow firmware or system-control logic to configure the converter and manage display-related functions. The 8 mm by 8 mm BGA package supports compact integration on multilayer printed circuit boards, although high-density ball-grid-array assembly requires careful PCB layout, thermal management, and inspection processes. The STDP2650AD is suited to computer monitors, graphics-adapter output cards, docking stations, industrial display systems, digital signage, and audiovisual equipment where a DisplayPort source must connect to an HDMI sink. A design using this converter must account for DisplayPort link requirements, HDMI output characteristics, reference-clock and power-supply implementation, connector integration, and the signal-integrity demands of high-speed video links. The package also requires assembly methods capable of handling fine-pitch BGA connections and adequate thermal pathways. A principal design consideration is that the verified snippets do not provide the complete electrical limits, supported display resolutions, refresh rates, color formats, operating-temperature range, pinout, or reference-design details. Engineers should therefore use the manufacturer datasheet for those values and for the required external components. The converter should be selected only after confirming compatibility among the DisplayPort source, supported HDMI mode, sink capability, control firmware, and system power architecture. This page consolidates verified distributor listings, package information, interface capabilities, and practical integration guidance. It also documents where primary datasheet verification remains necessary, rather than presenting unverified electrical values as guaranteed specifications.

見積もり お問い合わせ
STDP2650ADT - HDMI 1.4 DisplayPort Converter | Kinetic Technologies
STDP2650ADT

STDP2650ADT - HDMI 1.4 DisplayPort Converter | Kinetic Technologies

The Kinetic Technologies STDP2650ADT is an advanced DisplayPort-to-HDMI video converter IC designed for HDMI 1.4 display conversion and modern digital display interfaces. The device operates from a 1.2 V to 3.3 V supply, supports I2C and SPI control interfaces, and is supplied in an 81-BGA 8 x 8 mm surface-mount package. It is intended for systems that need to translate DisplayPort source signals into HDMI-compatible output signals while preserving programmable control and video-conversion functionality. A DisplayPort-to-HDMI converter is a video interface IC that bridges two display standards. DisplayPort is primarily used by computers, docking stations, monitors, and embedded systems, while HDMI remains common in televisions, projectors, displays, and consumer AV equipment. The converter IC sits between a DisplayPort source and an HDMI sink, handling digital video conversion and associated control signaling. This makes the STDP2650ADT relevant to adapters, docking systems, industrial panels, commercial displays, and embedded video equipment. The verified product information identifies the STDP2650ADT as an HDMI 1.4 video converter with I2C and SPI configuration control. Its 1.2 V to 3.3 V operating supply supports integration with low-voltage digital systems, while the 81-BGA package provides a compact surface-mount solution for multilayer PCB designs. The package format is intended for high-density equipment where connector placement, EMI control, and signal routing determine whether a converter can be implemented reliably. Compared with passive DisplayPort-to-HDMI adapters, an active converter IC can support source negotiation, programmable operating parameters, and system-level control through I2C or SPI. The control interface allows firmware or system logic to identify supported display configurations and manage the converter within a larger video subsystem. Because the verified data does not provide resolution, refresh-rate, color-depth, propagation-delay, operating-temperature, or absolute-maximum details, those specifications should be confirmed in the manufacturer datasheet before release to production. Typical uses include USB-C and Thunderbolt docking stations, DisplayPort-to-HDMI adapters, industrial HMI panels, digital signage, projector interfaces, and embedded display products. In these applications, the converter reduces the need for a separate external adapter and enables a compact board-level implementation. The design must still account for connector compliance, display timing support, power sequencing, ground continuity, and the impedance-sensitive high-speed signal paths. The primary design consideration is that the converter does not remove the need for careful PCB implementation. DisplayPort and HDMI links are high-speed differential interfaces, so trace routing, connector launches, reference planes, and return paths directly affect signal integrity. The STDP2650ADT should be evaluated against the exact source and sink requirements, including HDMI version, supported display timing, HDCP requirements, audio behavior, and the target power architecture. This page consolidates the verified distributor descriptions, package and interface information, sourcing links, and engineering guidance for the STDP2650ADT. It distinguishes confirmed data from specifications that still require datasheet confirmation, helping designers make a faster initial component-selection decision without treating unverified parameters as guaranteed capabilities.

見積もり お問い合わせ