マイクロコントローラ

製品 (20,000+)

MPC8275CVRMIBA - PowerQUICC II 266MHz SoC MPU, 516-PBGA | NXP
MPC8275CVRMIBA

MPC8275CVRMIBA - PowerQUICC II 266MHz SoC MPU, 516-PBGA | NXP

The NXP (formerly Freescale) MPC8275CVRMIBA is a PowerQUICC II family microprocessor based on the PowerPC G2_LE core, integrating a single 32-bit CPU running at 266 MHz with an on-chip RISC Communications Processor Module (CPM) for offloading serial-protocol work from the host core. It is offered in a 516-ball PBGA package (27 x 27 mm) and is rated for the industrial -40 C to +105 C temperature range. A PowerQUICC II processor is a system-on-chip (SoC) communications processor that combines a PowerPC host CPU with a dedicated CPM supporting HDLC, Ethernet (10/100 Mbit), ATM/UTOPIA, USB, I2C, SPI, and PCI. It sits above simple microcontrollers and below full application processors in the embedded hierarchy, and is classified as an integrated microprocessor (MPU) within power-management-adjacent embedded silicon. Key features include 505.4 MIPS sustained performance, integrated DRAM/SDRAM memory controller, dual 10/100 Ethernet MACs, PCI 2.2 interface, USB 1.1 host/client, HDLC TDM channels, UTOPIA PHY interface, and an external bus supporting up to 133 MHz operation. The CPM runs autonomously and handles DMA, protocol framing, and time-division multiplexing without host intervention. The MPC8275CVRMIBA is architecturally positioned between the lower-frequency MPC8270 (266 MHz-class) and the higher-throughput MPC8280, giving designers a balanced choice for cost-sensitive mid-range routers, DSLAM line cards, and industrial control gateways where deterministic protocol handling matters more than raw CPU throughput. Typical applications include wired networking routers and switches, telecom line cards (xDSL, ISDN, T1/E1), industrial serial gateways, VoIP media gateways, and embedded control platforms requiring deterministic multi-protocol I/O. The 516-PBGA package requires careful PCB layout with multiple power and ground planes for thermal management. When designing with this device, plan a 4- to 6-layer PCB with a continuous ground plane beneath the BGA and a minimum 1 oz copper inner layer for power distribution. Decouple each power pin with 100 nF X7R placed within 5 mm of the ball. Observe the 266 MHz core clock and 133 MHz external bus skew budgets specified in the NXP hardware design checklist. This page synthesizes distributor pricing, EOL signals, drop-in alternates, and practical PCB/layout guidance not collected in the manufacturer datasheet, giving an engineer a single decision-ready reference for the MPC8275CVRMIBA.

見積もり お問い合わせ
MPC8275VRMIBA - PowerQUICC II 266MHz MPU | NXP | 516-PBGA
MPC8275VRMIBA

MPC8275VRMIBA - PowerQUICC II 266MHz MPU | NXP | 516-PBGA

The NXP MPC8275VRMIBA is a PowerQUICC II communications processor built on the PowerPC G2_LE architecture, integrating a 266 MHz 32-bit core with a CPM (Communications Processor Module) co-processor, delivering 505.4 MIPS of processing throughput, and housed in a 516-ball PBGA (27x27 mm, 1 mm pitch) package. An MPU (Microprocessor Unit) is the central processing element of an embedded platform. Within the broader taxonomy, the MPC8275VRMIBA sits as: microprocessor -> embedded MPU -> communications processor -> PowerQUICC II SoC. PowerQUICC II parts target wired/wireless infrastructure where deterministic multi-protocol I/O and PCI connectivity are required on a single die. Key features include an integrated system-on-chip (SoC) design combining the PowerPC core with the CPM co-processor, dual 10/100 Ethernet MACs, PCI interface, USB, HDLC/ATM/UTOPIA support, and a 64-bit data bus. The HiPerMOS7 0.13-micron process provides lower power draw than previous PowerQUICC generations, while maintaining the same 516-PBGA footprint shared with MPC8270/MPC8280 family members. Architecturally, the MPC8275VRMIBA separates control-plane and data-plane tasks: the G2_LE core runs OS and management code, while the CPM handles serial protocol termination, DMA, and Fast Communications Channels. The 516-PBGA package (1 mm pitch) routes out the high pin count required for parallel peripheral buses, DDR memory controller, and dual Ethernet MII/RMII interfaces. Typical applications include wired/wireless infrastructure routers, multi-channel HDLC/TDM bridges, industrial PCI controller cards, DSLAM line cards, and ATM/UTOPIA edge nodes. The combination of PCI host bridge and integrated Ethernet MACs makes it well suited as a head-end controller in customer premises equipment. When designing with this device, thermal dissipation at 266 MHz must be evaluated against the PBGA's exposed-die thermal path. Boards should route all 516 balls to inner power/ground planes to maintain signal integrity on the parallel bus and to provide the decoupling capacitance required by the DDR SDRAM controller. This page synthesizes distributor pricing, drop-in same-family alternatives, and design notes not typically consolidated on a single product page, giving engineers a practical decision view of the MPC8275VRMIBA.

見積もり お問い合わせ
MPC8275ZQMIBA - PowerQUICC II 266MHz SoC MPU | NXP Semiconductors
MPC8275ZQMIBA

MPC8275ZQMIBA - PowerQUICC II 266MHz SoC MPU | NXP Semiconductors

The NXP Semiconductors MPC8275ZQMIBA is a PowerQUICC II integrated communications processor featuring a 32-bit Power Architecture CPU core running at 266 MHz, a 516-ball PBGA (27x27) package, and an integrated communications engine with PCI, USB, HDLC, Ethernet, and UTOPIA interfaces. It is a system-on-chip (SoC) member of the MPC82xx family, manufactured on a 0.13 micron HiP7 process, intended for wired and wireless infrastructure equipment. Background Knowledge - What is a PowerQUICC communications processor: PowerQUICC is NXP/Freescale's brand name for a family of integrated communications processors that combine a Power Architecture CPU core with a specialized communications processor module (CPM). The CPM offloads peripheral and networking tasks from the main CPU, enabling efficient handling of multiple WAN, LAN, and telecom protocols such as ATM, HDLC, Ethernet, USB, and UTOPIA. PowerQUICC II sits within the broader taxonomy of integrated communications processors -> microprocessors (MPU) -> processors -> semiconductors, and is widely deployed in routers, switches, DSLAMs, and industrial control equipment where deterministic multi-protocol I/O is required. Key features of the MPC8275ZQMIBA include a 266 MHz PowerPC G2_LE CPU core, hardware-accelerated communications via the CPM, integrated support for Fast Ethernet MAC, USB, PCI, HDLC, and UTOPIA, and a 1.5V core / 3.3V I/O dual-rail power design. The 516-pin PBGA package exposes extensive address/data buses and peripheral pins, supporting a wide variety of networking and embedded control applications. The device's commercial operating temperature range (0C to 105C) suits controlled-environment networking gear. At the architecture level, the MPC8275ZQMIBA uses a Harvard-style bus architecture for the CPU, a unified 32-bit peripheral bus for the CPM, and dedicated DMA channels that allow the CPM to move data between peripherals and memory without CPU intervention. This integration reduces BOM count and board area relative to discrete CPU-plus-communications-controller designs, while the wide peripheral set lowers the cost of multi-protocol product variants. Typical applications include wired and wireless infrastructure equipment (DSLAMs, routers, wireless base stations), industrial networking gateways, protocol-conversion appliances, and embedded control systems that require deterministic serial and packet I/O. The combination of CPU throughput and CPM-driven I/O makes it well-suited for products that aggregate multiple physical interfaces. Design consideration: Power-sequencing must follow NXP's reference design because the MPC8275ZQMIBA uses split 1.5V core and 3.3V I/O rails; bring-up order affects CPM register state. Additionally, the large 516-ball PBGA requires careful BGA PCB layout with controlled-impedance traces and matched-length clocks to maintain signal integrity at the full 266 MHz bus speed. This page synthesizes distributor stock checks, NXP/Freescale PowerQUICC II family cross-references, and practical BGA bring-up design notes that go beyond the manufacturer datasheet to assist embedded and network-equipment engineers in component selection.

見積もり お問い合わせ
MPC8280VVUPEA - 450MHz PowerQUICC II SoC MPU | NXP
MPC8280VVUPEA

MPC8280VVUPEA - 450MHz PowerQUICC II SoC MPU | NXP

The NXP (formerly Freescale) MPC8280VVUPEA is a PowerQUICC II family microprocessor integrating a 32-bit PowerPC G2_LE core running at 450 MHz (885 MIPS) with on-chip communications peripherals, housed in a 480-pin TBGA package measuring 37.5x37.5 mm. It combines a high-performance e603e-class core with the CPM (Communications Processor Module) co-processor to offload DMA, HDLC, ATM, USB, Ethernet and PCI bridging from the core. A microprocessor (MPU) is an integrated circuit that contains the CPU, caches, memory controller and peripheral interfaces on one chip; in the PowerQUICC II family the core is paired with a dedicated RISC-based CPM that handles serial and networking I/O autonomously, making the device a single-chip SoC for embedded networking. The MPC8280 sits at the top of the G2_LE family, offering higher core and bus clock options than the lower-cost MPC8270 and MPC8275 variants. Key features include 16 KB instruction cache and 16 KB data cache, dual 10/100 Mbps Ethernet MACs with MII/RMII interfaces, USB 1.1 host/function controller, dual HDLC/serial controllers supporting up to T3/E3 rates, a UTOPIA-II/PATM PHY interface for ATM, and a 32-bit/66 MHz PCI interface that can operate in host or agent mode. The integrated memory controller supports DDR SDRAM at up to 133 MHz and includes a 64-bit local bus with glue-less Flash/SRAM support. Architecturally the device splits processing duties between the PowerPC G2_LE core (running user code and protocol stacks) and the CPM co-processor, which services DMA channels and protocol engines through its own microcoded RISC engine. This dual-engine approach delivers high sustained throughput on serial interfaces without burdening the main core with interrupt-driven I/O, characteristic of PowerQUICC II design. Typical applications include industrial multi-port routers, DSLAM line cards, wireless base-station controllers, VoIP media gateways, industrial Ethernet switches, and PCI-based embedded control cards. The integrated CPM eliminates external protocol ASICs, reducing BOM cost in communications equipment. When designing with this device, plan power sequencing for the 1.8 V and 3.3 V rails and ensure proper JTAG pull-ups. Designers should also budget for a substantial 4-layer PCB with matched-impedance Ethernet and PCI traces. This page synthesizes distributor pricing, drop-in alternatives, and practical design guidance not found in the manufacturer datasheet, providing engineers a single reference for sourcing and substitution decisions.

見積もり お問い合わせ
MPC8280ZUUPEA - PowerQUICC II MPU, 450MHz, 480-TBGA | NXP
MPC8280ZUUPEA

MPC8280ZUUPEA - PowerQUICC II MPU, 450MHz, 480-TBGA | NXP

The NXP MPC8280ZUUPEA is a PowerQUICC II family microprocessor integrating a PowerPC G2_LE core with a Communications Processor Module (CPM) on a single die, clocked at 450 MHz core / 300 MHz CPM, housed in a 480-pin TBGA package (37.5 x 37.5 mm). It is built on NXP/Freescale's HiPerMOS7 0.13-micron process technology and targets networking, telecom, and industrial control applications requiring both RISC-class processing and high-throughput serial communications. A PowerQUICC II microprocessor belongs to the broader category of communications processors - System-on-Chip (SoC) devices that combine a general-purpose CPU with dedicated serial-protocol engines. Within the embedded hierarchy, it sits as: PowerQUICC II -> PowerQUICC -> embedded MPU -> microprocessor -> integrated circuit. The integrated CPM offloads typical communications tasks such as HDLC, UART, USB, Ethernet MAC, ATM/UTOPIA, and PCI bridging from the main core, which is the architectural origin of PowerQUICC's enduring popularity in legacy networking equipment. Key features include a 32-bit PowerPC G2_LE core with MMU and on-chip caches, integrated CPM supporting 10/100 Ethernet, HDLC/SDLC, USB 1.1, UART, I2C, SPI, PCI 2.2 bridge, and a 64-bit local bus. The device supports SDRAM and DRAM memory controllers with ECC, and offers Security Engine features in some -Z variants. Operating temperature spans 0 to 105C, suitable for commercial and lightly-industrialized environments. The architecture combines an out-of-order-capable G2_LE scalar core with a peripheral engine optimized for cell-based protocol termination, allowing wire-speed handling of multiple HDLC or Ethernet channels without saturating the CPU. Power dissipation is typically under 2 W at full load, a notable improvement over first-generation PowerQUICC II silicon thanks to the HiP7 process shrink. Typical applications include SOHO/enterprise routers, DSLAM line cards, industrial control SoC platforms, networked storage controllers, and legacy telecom baseband cards. The PCI bridge and USB host capability make it well suited to peripheral-rich embedded designs. When designing with the MPC8280ZUUPEA, allocate careful attention to the core supply rail (1.5 V) decoupling and to the TBGA thermal management; 480 balls in a 37.5 mm body concentrate heat at the die shadow. Consider the -C variant (MPC8280CZUUPEA) if an extended temperature grade is required. This page synthesizes distributor pricing, datasheet pins-and-parmeters, and practical design notes drawn from the NXP datasheet and third-party reference designs, providing information gain beyond the manufacturer product page.

見積もり お問い合わせ
MPC8306CVMADDCA - PowerQUICC II Pro 266MHz SoC | NXP Semiconductors
MPC8306CVMADDCA

MPC8306CVMADDCA - PowerQUICC II Pro 266MHz SoC | NXP Semiconductors

The NXP Semiconductors MPC8306CVMADDCA is a PowerQUICC II Pro communications processor based on the Power Architecture e300c3 core, operating at 266 MHz and housed in a 369-pin PBGA (19x19 mm) package. It integrates a single 32-bit core with QUICC Engine technology supporting HDLC, TDM and 10/100 Ethernet (R/MII), plus DDR2 memory controller, USB, CAN, and IEEE 1588 v2 hardware time stamping on the MPC8306 variant. A PowerQUICC processor is a communications-centric system-on-chip (SoC) that combines a Power Architecture CPU with one or more protocol engines, originally designed by Freescale (now NXP) to offload networking, telecom and industrial control workloads from the main CPU. The PowerQUICC family sits at the intersection of microcontrollers (MCUs) and high-performance application processors, evolving into the QorIQ and Layerscape families for newer designs. Understanding this hierarchy helps engineers recognize that the MPC8306 is positioned for cost-sensitive, low-power embedded networking where deterministic protocol handling matters more than raw compute throughput. Key features of the MPC8306CVMADDCA include a 266 MHz e300c3 core with 16 KB instruction / 16 KB data L1 cache, a 32-bit DDR1/DDR2 memory controller with ECC, two 10/100 Ethernet controllers with QoS and classification, two USB 2.0 full-speed controllers (host/device/OTG), dual CAN 2.0B controllers, four UART, dual I2C, SPI, and a local bus controller. Security is supported via integrated SEC 2.0 with DES/3DES/AES/SHA accelerators and a true random number generator. The MPC8306 architecture uses a 32-bit PowerPC superscalar core paired with QUICC Engine technology, which historically handled ATM, HDLC, TDM and Ethernet protocol termination in earlier PowerQUICC generations. On the MPC8306, the QUICC Engine focuses on HDLC, TDM, and Ethernet offload, while the e300c3 core runs control-plane software such as Linux or VxWorks. The device integrates DDR2 memory controller logic that supports up to 256 MB of DDR2 with ECC, eliminating the need for an external memory controller chip. Typical applications include industrial Ethernet gateways, smart grid substation controllers, factory automation PLCs, protocol converters (HDLC/Ethernet/CAN), networked printers, and low-end WiMAX/3G base station control cards. The integrated IEEE 1588 v2 time stamping on the MPC8306 makes it well suited for precision timing over Ethernet in telecom and power-utility networks. When designing with this device, note that the package is a 369-ball PBGA (19x19 mm, 1 mm pitch) which requires a 6-layer PCB minimum for signal integrity and a clean thermal copper pour under the exposed die area. The 0.95 V to 1.05 V core voltage requires careful sequencing with respect to the 3.3 V I/O supply. Also confirm that your firmware target supports the e300c3 core architecture before committing to the MPC8306 over an ARM-based alternative. This page synthesizes distributor stock, drop-in pin-compatible alternatives, parameter comparison and design notes that go beyond the manufacturer datasheet, helping embedded engineers evaluate the MPC8306 for cost-sensitive communications designs.

見積もり お問い合わせ
MPC8306SCVMABDCA - PowerQUICC II Pro SoC 133MHz | NXP
MPC8306SCVMABDCA

MPC8306SCVMABDCA - PowerQUICC II Pro SoC 133MHz | NXP

The NXP MPC8306SCVMABDCA is a PowerQUICC II Pro communications processor built on Power Architecture e300c3 technology, integrating a single 32-bit core running up to 133 MHz in a 369-ball MAP-BGA package (19x19 mm). The device combines a CPU subsystem with the QUICC Engine for HDLC, TDM and 10/100 Ethernet (R/MII) processing, plus IEEE 1588 v2 time-stamping support, making it a cost-effective SoC for embedded networking and industrial control. A communications SoC (System-on-Chip) is an integrated circuit that consolidates a processor core, memory controllers, and dedicated communications peripherals onto a single die. The MPC8306SCVMABDCA sits in the hierarchy SoC -> communications processor -> PowerQUICC II Pro -> MPC830x family, where it serves as the ultra low-end node targeting price-sensitive wireline and industrial designs. Its integrated QUICC Engine offloads bit-level protocol processing from the CPU, enabling deterministic throughput for HDLC and TDM traffic. Key features include a 32-bit PowerPC e300c3 core, 133 MHz operation, DDR2 memory controller, 16-bit local bus, dual 10/100 Ethernet MACs, USB 2.0 (full-speed), HDLC/TDM support via QUICC Engine, IEEE 1588 v2 hardware time-stamping, and an extended -40C to +105C industrial operating temperature range. The 369-PBGA MAP-BGA package exposes the full peripheral set while keeping the PCB footprint compact. Security, boot, and reset features include secure boot, multiple reset sources, and JTAG boundary scan. The architecture pairs the e300c3 superscalar core with the QUICC Engine block, which contains RISC communication controllers optimized for serial protocol termination. On-chip DDR2 controller supports common industrial memory configurations, while the local bus controller glues to NOR flash, NAND flash, and FPGA/ASIC peripherals. Industrial-grade temperature compliance and a long-life roadmap (when active) make the part suitable for legacy factory automation, telecom edge nodes, and serial concentrator designs. Typical applications include industrial Ethernet gateways, HDLC/TDM line-card controllers, sub-rack telecom equipment, serial-protocol concentrators, secure embedded routers, and legacy industrial control boards. The combination of QUICC Engine, dual Ethernet, and USB also fits retail/POS terminals that need deterministic serial-channel processing alongside IP connectivity. When designing with this device, ensure DDR2 trace lengths follow the NXP reference design layout guide and that the QUICC Engine firmware (RISC microcode) is loaded into the designated memory region during boot. Thermal management is straightforward due to the modest 133 MHz clock and industrial-grade silicon. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

見積もり お問い合わせ
MPC8306SVMABDCA - PowerQUICC II Pro MPU, e300, 133MHz | NXP
MPC8306SVMABDCA

MPC8306SVMABDCA - PowerQUICC II Pro MPU, e300, 133MHz | NXP

The NXP MPC8306SVMABDCA is a PowerQUICC II Pro integrated communications processor based on the e300c3 core built on Power Architecture technology, delivering 133 MHz of single-core 32-bit processing in a 369-ball MAPBGA (19x19 mm) package. It is part of the cost-effective MPC830x communications processor family and integrates QUICC Engine technology capable of supporting HDLC, TDM, and 10/100 R/MII Ethernet interfaces, along with DDR2 memory controller, USB, and IEEE 1588 time-stamping support. A communications MPU (microprocessor unit) is a system-on-chip class device that integrates one or more processor cores with networking peripherals, memory controllers, and connectivity interfaces designed for protocol processing, routing, and embedded control. Within the broader taxonomy, the MPC8306S belongs to the PowerQUICC II Pro lineage of communications processors, which evolved from Freescale's QUICC engine architecture and occupies the niche between microcontrollers and high-end application processors, optimized for wired and industrial communications rather than graphical or compute workloads. Key features include one e300c3 core running at 133 MHz with 32 KB of instruction cache and 32 KB of data cache, a 16-bit DDR2 memory controller up to 333 MHz data rate, dual 10/100 Ethernet MACs with MII/RMII support, a USB 2.0 Full-Speed interface, dual UART, HDLC/TDM interfaces, and JTAG debug support. Power management is handled through multiple power domains and a low-power standby mode. Architecturally, the device combines a PowerPC e300c3 scalar core with a dedicated QUICC Engine RISC co-processor that offloads protocol processing for HDLC, TDM, and Ethernet, allowing deterministic throughput independent of CPU load. The 369-ball MAPBGA exposes the DDR2 controller with ECC, PCI Express (where enabled), USB, MII/RMII, UART, and GPIO, and supports industrial-grade temperature operation up to 105C. Typical applications include industrial routers and gateways, factory automation controllers, DSL and broadband access equipment, networked printers, point-of-sale terminals, and serial-to-Ethernet protocol bridges. The combination of QUICC Engine offload and DDR2 memory makes the part well suited to multi-protocol aggregation where deterministic latency is required. When designing with this part, note that the MPC8306S is the 'S' subset (without IEEE 1588 v2 time stamping present on the full MPC8306), and power sequencing for the DDR2 rail must follow NXP's reference design to avoid latch-up at cold start. Static I/O voltages are 1.8 V / 2.5 V / 3.3 V tolerant, and the core runs from a separate 1.0 V or 1.2 V supply depending on speed grade. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes that are not consolidated in the manufacturer datasheet, enabling faster component selection for communications and industrial designs.

見積もり お問い合わせ
MPC8306VMABDCA - PowerQUICC II Pro SoC, e300, 133MHz | NXP
MPC8306VMABDCA

MPC8306VMABDCA - PowerQUICC II Pro SoC, e300, 133MHz | NXP

The NXP MPC8306VMABDCA is a PowerQUICC II Pro communications SoC integrating a PowerPC e300c3 core running at 133 MHz with a QUICC Engine subsystem, packaged in a 369-ball LFBGA (19x19 mm) and rated 0 to 105 °C. Built on Power Architecture technology, the device targets cost-sensitive wired-communications gateways and industrial control applications. It pairs a 32-bit CPU core with on-chip DDR2 memory controllers and a rich communications peripheral set, eliminating the need for an external protocol processor in many designs. What is a PowerQUICC communications processor? The PowerQUICC family is NXP's (formerly Freescale's) line of Power-Architecture-based system-on-chips that integrate a general-purpose CPU with a hardware protocol offload engine called the QUICC Engine. This category sits within the broader taxonomy of microprocessors -> embedded microprocessors -> communications processors -> SoC. The QUICC Engine handles HDLC, TDM and 10/100 Ethernet MACs (R/MII), letting the CPU focus on application and control-plane tasks instead of bit-banging protocols. Key features include a single 32-bit e300c3 core at 133 MHz, DDR2 memory controller with ECC, dual 10/100 Ethernet MACs with R/MII, USB 2.0 Full-Speed, CAN 2.0, HDLC and TDM time-slot support, an integrated security engine, and IEEE 1588 v2 hardware time stamping on the MPC8306 (versus the MPC8306S, which omits 1588). The part is supplied in a 369-pin LFBGA measuring 19x19 mm and operates from a 0 to 105 °C industrial temperature range. Power is typically delivered through a multi-rail scheme with core, I/O and DDR2 supplies around 1.0 V / 1.8 V / 3.3 V. From an integration standpoint, the device integrates the DDR2 controller, Ethernet MACs, TDM/HDLC channels, USB, CAN, I²C, SPI, UARTs, timers, GPIO, and a DMA engine on a single die. Eliminating a companion protocol chip reduces BOM cost and PCB area, while the QUICC Engine's hardware acceleration preserves CPU bandwidth for routing, security or industrial-protocol stacks. Typical applications include industrial Ethernet gateways, factory-automation PLCs, building-automation controllers, smart-grid concentrators, branch-office routers, VoIP access equipment, and serial-protocol concentrators (HDLC/TDM). The combination of QUICC Engine protocol offload and DDR2 memory makes it suitable for medium-throughput control-plane workloads. A key design consideration is power-rail sequencing: the core, I/O and DDR2 rails must be brought up in the correct order to avoid latch-up. Follow the sequencing and decoupling guidance in the hardware documentation, and ensure the LFBGA PCB layout meets the 19x19 mm BGA escape and thermal-coupling rules. This page consolidates NXP and distributor data, drop-in alternatives, and design notes that streamline evaluation of the MPC8306VMABDCA for new designs and legacy refurbishment alike.

見積もり お問い合わせ
MPC8306VMACDCA - PowerQUICC II Pro SoC 200MHz e300 | NXP
MPC8306VMACDCA

MPC8306VMACDCA - PowerQUICC II Pro SoC 200MHz e300 | NXP

The NXP MPC8306VMACDCA is a PowerQUICC II Pro communications SoC built on Power Architecture technology with an e300c3 core running at 200 MHz, packaged in a 369-ball PBGA (19x19 mm) and rated for 0 to 105C industrial-extended operation. It integrates a 32-bit PowerPC core, DDR2 memory controller, HDLC/TDM time-division controllers, dual Ethernet MACs, USB 2.0, and CAN interfaces on a single die, targeting cost-effective wireline/wireless access and industrial gateway designs. A PowerQUICC II Pro SoC is a system-on-chip that combines a PowerPC host processor with multiple specialized communications peripherals (Ethernet, HDLC, ATM, TDM, USB, CAN) on a single die, allowing one device to replace what would otherwise require a CPU plus separate PHY/controller ICs. The PowerQUICC II Pro family sits within NXP's Power Architecture portfolio, above simple 8/16-bit microcontrollers and below higher-end QorIQ multicore processors, serving the cost-sensitive edge of the communications infrastructure. Key features of the MPC8306VMACDCA include the e300c3 32-bit core at 200 MHz, on-chip DDR1/DDR2 SDRAM controller with 16-bit data width, dual 10/100 Ethernet MACs (one RGMII + one MII/RMII), USB 2.0 Full-Speed host/device, two CAN 2.0 controllers, four HDLC/TDM channels, and a 32-bit PCI interface. Security is provided by a SEC 2.2 accelerator (AES, DES, 3DES, MD5/SHA-1) on the higher-tier MPC8306S variant. The device uses a 32-bit PowerPC Book E instruction set with MMU and 16 KB instruction / 16 KB data L1 caches, while the integrated system interface unit (SIU) handles the 60x-compatible external bus plus PCMCIA/CompactFlash support. This balance of compute, memory bandwidth, and integrated peripherals makes it well suited for low-end routers, industrial controllers, and printed-circuit media gateways that need determinism without multicore complexity. Typical applications include low-cost SOHO routers, integrated access devices (IAD), industrial Ethernet gateways, CAN-based building automation nodes, and serial-protocol protocol converters. The wide peripheral integration reduces external component count, and the 0 to 105C operating range suits outdoor enclosures and industrial cabinets. When designing with the MPC8306VMACDCA, allocate sufficient PCB area to the 369-ball PBGA (19x19 mm, 1 mm pitch) - four to six layers with a continuous ground plane are recommended to keep DDR2 signal integrity intact. Decouple VDD_CORE and VDD_IO rails with 100 nF plus 10 µF ceramic capacitors placed as close to the balls as possible. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

見積もり お問い合わせ
MPC8308CVMADD - PowerQUICC II Pro SoC 266MHz | NXP Semiconductors
MPC8308CVMADD

MPC8308CVMADD - PowerQUICC II Pro SoC 266MHz | NXP Semiconductors

The NXP Semiconductors MPC8308CVMADD is a PowerQUICC II Pro Power Architecture system-on-chip (SoC) integrating an e300c3 core running at 266 MHz, a DDR2 memory controller, one PCI Express interface, dual Gigabit Ethernet MACs, USB 2.0, and a local bus controller in a 473-pin MAPBGA package measuring 19x19 mm. The part is offered in the industrial extended temperature range -40C to +105C, making it qualified for thermally demanding embedded applications. What is a PowerQUICC processor? PowerQUICC (pronounced "power-quick") is NXP/Freescale's long-running family of Power Architecture communications processors that integrate CPU core(s) with networking and peripheral IP. It belongs to the broader class of integrated communications processors (also called networking SoCs or application processors for embedded networking). Within that hierarchy, MPC8308 sits in the PowerQUICC II Pro sub-family alongside the MPC8306, MPC8309, and MPC831x devices, optimized for cost-sensitive and power-sensitive networking endpoints such as home gateways, WLAN access points, and industrial data concentrators. Key features include a 16 KB instruction cache plus 16 KB data cache on the e300c3 core, a 266 MHz DDR2 controller (data rate), one x1 PCI Express Gen1 endpoint/root complex, two 10/100/1000 MACs supporting MII and RGMII, USB 2.0 (host/device), and a flexible local bus controller with NAND flash support. The integrated peripherals eliminate the need for an external bridge chip, reducing both BOM cost and PCB area in customer designs. The MPC8308CVMADD architecture combines the Book-E enhanced Power Architecture core with NXP's QUICC Engine subsystem that handles the networking and DMA offload. This dual-engine partitioning allows the CPU to run control-plane software while the QUICC Engine accelerates packet processing, a classic PowerQUICC design pattern. Typical applications include smart-grid home energy gateways, data concentrators, wireless LAN access points/routers, industrial Ethernet bridges, networked printers, and low-end fanless NAS/print server appliances. The wide temperature range and integrated GbE/PCIe/USB make it well suited to industrial networking equipment. Designers should budget PCB area for the 19x19 mm MAPBGA land pattern, route DDR2 with matched-length traces per the NXP hardware specification, and validate the 266 MHz core/DDR data rate against the software workload's interrupt and DMA latency budgets. Reference schematics and layout checklists are documented in the NXP MPC8308 hardware specification. This page synthesizes distributor stock, lifecycle context, and pin-compatible alternative analysis not found in the manufacturer datasheet alone.

見積もり お問い合わせ
MPC8308CVMAFD - PowerQUICC II Pro SoC 333MHz e300 | NXP
MPC8308CVMAFD

MPC8308CVMAFD - PowerQUICC II Pro SoC 333MHz e300 | NXP

The NXP MPC8308CVMAFD is a PowerQUICC II Pro system-on-chip built around the e300c3 Power Architecture core running up to 333 MHz, packaged in a 473-pin MAP-BGA (19x19 mm). The device combines a 32-bit CPU with 16 KB instruction and 16 KB data caches, a DDR2 memory controller supporting up to 266 MHz data rate, a local bus controller, one PCI Express interface, dual 10/100/1000 Ethernet MACs (MII/RGMII), and a USB 2.0 high-speed interface, delivering a highly integrated networking and industrial-control platform. A PowerQUICC II Pro SoC is a communications-centric microprocessor family from NXP (formerly Freescale) that integrates a Power Architecture CPU with networking peripherals and a memory subsystem on a single die. The MPC8308 belongs to the broader PowerQUICC hierarchy (PowerQUICC -> PowerQUICC II -> PowerQUICC II Pro) and is targeted at cost-sensitive, low-power embedded networking applications such as smart-grid gateways, industrial control, and small-to-medium WLAN access points. The 'C' prefix indicates the e300c3 core variant, while 'VM' denotes the MAP-BGA package family and 'AFD' encodes the temperature grade and speed designation. Key features of the MPC8308CVMAFD include the e300c3 core at 333 MHz, integrated DDR2 memory controller with 16-bit and 32-bit data paths, a local bus controller for glueless connection to flash and peripherals, hardware encryption acceleration, and a wide operating voltage range of 1V (core), 1.8V, 2.5V, and 3.3V I/O. The 473-pin MAP-BGA provides ample signal integrity for the multi-gigabit serial interfaces while keeping board area compact for embedded designs. Typical applications for the MPC8308CVMAFD include smart-grid home energy gateways, data concentrators, wireless LAN access points, femtocell base stations, consumer printing controllers, industrial control and factory automation, and other low-power networking platforms where integrated gigabit Ethernet and PCI Express simplify board design. The wide temperature range supports both commercial and extended-temperature deployments. When designing with this device, ensure the DDR2 controller is properly terminated and that the multi-rail power sequence (1V core before 1.8V/2.5V/3.3V I/O) is respected to avoid latch-up. The 473-ball BGA requires a minimum of six PCB layers with via-in-pad recommended for the high-speed DDR2 and RGMII signals, and thermal copper pad soldering is critical for long-term reliability at elevated ambient temperatures.

見積もり お問い合わせ
MPC8308CVMAGD - PowerQUICC II Pro 400MHz e300 MPU | NXP
MPC8308CVMAGD

MPC8308CVMAGD - PowerQUICC II Pro 400MHz e300 MPU | NXP

The NXP MPC8308CVMAGD is a cost-effective, low-power, highly integrated host processor from the PowerQUICC II Pro family, featuring a PowerPC e300c3 core running at 400MHz in a 473-ball MAPBGA (19x19mm, 0.8mm pitch) package. It combines a 32-bit RISC CPU with a high-performance peripheral set targeting price-sensitive networking and industrial embedded designs, while sustaining industrial-grade thermal operation from -40C to +105C junction temperature. A PowerQUICC II Pro processor is a highly integrated system-on-chip (SoC) built around the Power Architecture (PowerPC/e300) CPU family, designed for communications, networking, and industrial control applications where deterministic behaviour, low power consumption, and rich connectivity matter more than raw GHz performance. The MPC8308CVMAGD extends the PowerQUICC lineage by adding a faster e300c3 core, more advanced peripheral interfaces, and lower power compared to earlier PowerQUICC II parts while keeping software compatibility with the broader PowerQUICC ecosystem. Key features include a 32-bit e300c3 single-issue core with 8KB instruction and 8KB data caches, a 16-bit DDR2 memory controller, two 10/100/1000 Mbps Ethernet controllers (one RGMII, one SGMII), a USB 2.0 Full-Speed host/device controller, an integrated security engine, and a complete set of communications peripherals such as UART, SPI, I2C, and timers. The device integrates a QUICC Engine UCC supporting HDLC/TDM, SUART, BISYNC, and Transparent modes for legacy telecom interworking alongside a 16-bit local bus and PCI Express endpoint (x1). Architecture-wise, the MPC8308CVMAGD is implemented in a 90nm CMOS process, delivering sub-1W typical power consumption at 400MHz with full peripheral operation, and a typical core supply (Vdd) of 1.0V plus I/O supply of 1.8V/2.5V/3.3V. The on-chip DDR2 controller supports up to 256MB of addressable memory, the integrated security engine performs DES/3DES/AES/SHA-1/MD5/RNG, and the QUICC Engine permits protocol-aware TDM/framer interfacing without burdening the CPU. Typical applications include smart-grid home energy gateways, data concentrators, wireless LAN access points, wireless femto base stations, industrial control and factory automation nodes, and consumer printing products. In each, the combination of the e300c3 core with hardware encryption and deterministic TDM peripherals lets the BOM shrink to a single SoC plus memory and PHYs. Design consideration: the 473-MAPBGA at 0.8mm pitch requires 4-layer PCB with microvia or laser-drilled stack-up; XAIPART recommends at least eight thermal vias under the exposed die-pad area, and to keep DDR2 trace lengths matched to within 25 mils and 90-ohm differential-impedance-controlled for RGMII/SGMII. This page synthesizes distributor pricing, drop-in same-family alternatives (MPC8308CVMAGDA, MPC8308VMAGDA, MPC8308CVMAJD) and practical design notes not found in the manufacturer datasheet.

見積もり お問い合わせ
MPC8308CZQAGD - PowerQUICC II Pro 400MHz SoC | NXP MAP-BGA
MPC8308CZQAGD

MPC8308CZQAGD - PowerQUICC II Pro 400MHz SoC | NXP MAP-BGA

The NXP MPC8308CZQAGD is a PowerQUICC II Pro integrated communications processor built around a Power Architecture e300c3 core running at 400 MHz, housed in a 473-ball MAP-BGA (19x19) package. As a member of the MPC8308 family, it combines a low-cost, low-power host CPU with a dedicated communications engine for embedded networking applications. The integrated QUICC Engine subsystem handles protocol termination offloading, freeing the host core for application processing. The category of this device is a communications processor SoC, which sits hierarchically under microprocessors (MPU) -> embedded processors -> SoC -> power management / communications IC. The QUICC Engine is NXP's legacy technology that evolved into the DPAA/QorIQ families; it remains in production for cost-sensitive industrial designs where proven firmware stacks are valued over bleeding-edge throughput. System designers choose this category when they need deterministic protocol handling without taxing the host CPU. Key features include a single 32-bit e300c3 core at 400 MHz, 16 KB I-cache and 16 KB D-cache, integrated DDR1/DDR2 memory controller, dual 10/100/1000 Ethernet MACs with GMII/RGMII support, USB 2.0 high-speed host/device/OTG controller, and PCI Express endpoint interface. The device operates from 1.0 V core / 1.8 V / 2.5 V / 3.3 V I/O supplies and integrates 256 KB of SRAM. Industrial temperature grade (-40C to +105C) is supported, with lead-free 473-MAPBGA packaging. Architecture-wise, the e300c3 core executes the Power Architecture Book E instruction set, supporting virtualization, MMU, and standard peripheral interfaces. The QUICC Engine operates as a separate RISC subsystem handling HDLC, ATM, and Ethernet MAC-level processing. The combination of host CPU plus dedicated comms engine delivers deterministic throughput for routing and bridging protocols. Typical applications include smart grid home energy gateways, data concentrators, industrial wireless LAN access points, and wireless routers. The wide protocol support also makes it suitable for low-end router aggregation, IP-PBX control plane processors, and serial-to-Ethernet protocol converters. The 400 MHz variant balances CPU performance against active power consumption. When designing with this SoC, ensure the DDR2 memory layout follows the reference design guidelines for impedance-controlled traces, and that thermal relief is provided on the BGA substrate for sustained 400 MHz operation. Firmware must initialize the QUICC Engine microcode tables before comms port activation. This page consolidates distributor pricing, pin-compatible MPC8308 family members, and practical design notes not found in the standalone datasheet.

見積もり お問い合わせ
MPC8308CZQAGDA - PowerQUICC II Pro SoC 400MHz | NXP Semiconductors
MPC8308CZQAGDA

MPC8308CZQAGDA - PowerQUICC II Pro SoC 400MHz | NXP Semiconductors

The NXP Semiconductors MPC8308CZQAGDA is a PowerQUICC II Pro integrated host processor built around the Power Architecture e300c3 core, delivering up to 400 MHz of CPU performance in a 473-pin MAP-BGA (19x19 mm) package. It is a cost-effective, low-power, highly integrated system-on-chip (SoC) designed for networking and industrial control applications such as smart grid home energy gateways, wireless LAN access points, femtocells, consumer printers, and factory automation. The device integrates DDR2 memory controller, PCI Express, Gigabit Ethernet, and USB 2.0 interfaces on-chip. A PowerQUICC II Pro SoC belongs to the family of communications processors that combine a high-performance Power Architecture core with integrated peripheral controllers. Within the broader taxonomy, the MPC8308 sits inside the PowerQUICC family, then communications processors, then microprocessors (MPU), then integrated circuits (IC). Its integrated DDR2 controller eliminates the need for an external memory controller chip, reducing board area and BOM cost in cost-sensitive designs. Key differentiating features include the on-chip security engine, dual Gigabit Ethernet MACs with integrated PHYs, and hardware acceleration for common networking tasks. The processor supports a wide operating temperature range of -40C to +105C, making it suitable for industrial environments. Compared with the MPC8308CZQAGD (Rev 1.0), the 'A' suffix (Rev 1.1) typically denotes an updated revision with errata fixes and minor functional refinements per Freescale/NXP documentation practice. Architecturally, the e300c3 core implements the Power Architecture Book E instruction set with a 16 KB L1 instruction cache and 16 KB L1 data cache. The system interface unit (SIU) glues DDR2, local bus, and PCI Express controllers to the core, while the communication-specific peripherals are managed through dedicated DMA engines that offload protocol processing from the CPU. Typical applications include smart grid home energy gateways, data concentrators, wireless LAN access points, wireless femto base stations, consumer printers, and industrial control/automation systems. The integrated Gigabit Ethernet and PCI Express interfaces are particularly valuable in networked embedded designs where BOM cost must be minimized. When designing with this part, ensure the PCB footprint matches the 473-pin MAP-BGA land pattern with proper via-in-pad or dog-bone fanout. Decoupling must include bulk capacitors near the core and DDR2 supplies, and DDR2 signal routing must follow the fly-by termination recommended in the hardware specification. Note that this part is marked End-of-Life (EOL) on the NXP product page; designers should evaluate the latest PowerQUICC successors or equivalent NXP layerscape devices for new designs. This page synthesizes distributor pricing, drop-in alternative MPNs, and practical design notes (BGA fanout, DDR2 layout, thermal considerations) not consolidated in the manufacturer datasheet, alongside a parameter comparison against MPC8308 family drop-in variants.

見積もり お問い合わせ
MPC8308VMADD - PowerQUICC II Pro 266MHz SoC | NXP
MPC8308VMADD

MPC8308VMADD - PowerQUICC II Pro 266MHz SoC | NXP

The NXP MPC8308VMADD is a cost-optimized, low-power PowerQUICC II Pro system-on-chip (SoC) integrating an e300c3 Power Architecture CPU core running at 266 MHz, paired with a complete networking peripheral set for embedded infrastructure designs. It is manufactured on a 0.09 um CMOS process and ships in a 473-pin MAP-BGA (19x19) package with 1.0 V core and 1.8 V/2.5 V/3.3 V I/O rails. The MPC8308VMADD belongs to NXP's MPC8308 family, which embeds DDR2 memory controller, PCI Express, Gigabit Ethernet, and USB 2.0 interfaces alongside the legacy QUICC Engine for protocol termination. A PowerQUICC II Pro SoC is an integrated communications processor that combines a general-purpose Power Architecture CPU with hardware accelerators and high-speed serial interfaces, designed to consolidate what previously required a host CPU plus several interface ASICs into a single device. Compared with discrete CPU-plus-MAC or CPU-plus-PHY designs, an MPC8308-class SoC reduces board area, BOM cost, and power consumption by absorbing Gigabit Ethernet MACs, PCIe endpoint/root complex logic, DDR2 SDRAM control, and USB into one BGA package. The result is a turnkey platform for low-cost, networked embedded appliances. Key features of the MPC8308VMADD include a 32-bit single-issue e300c3 core with MMU and separate 16 KB/16 KB instruction and data caches, hardware DDR2 SDRAM controller up to 266 MHz, dual integrated 10/100/1000 Mbps Ethernet MACs (RGMII), one PCI Express x1 link, USB 2.0 (Host or Device), local bus, and two UARTs. An integrated QUICC Engine block assists with TDM and packet processing, while security features include basic cryptographic accelerators. Industrial-grade variants (VMADx suffix) operate from 0 C to 105 C. The MPC8308VMADD architecture connects the CPU to a multi-channel DDR2 memory controller via a 64-bit coherence fabric, with peripheral traffic arbitrated through configurable on-chip buses. The integrated Gigabit Ethernet MACs use RGMII to external PHYs, eliminating the need for an external switch IC in small-port gateways. Compared with higher-tier PowerQUICC II Pro parts, the MPC8308 drops the second CPU core and trims cache size, achieving lower power for cost-sensitive designs. Typical applications include smart grid home energy gateways, industrial data concentrators, wireless LAN access points, wireless femto base stations, consumer printers, and industrial controllers. The 0 C to 105 C operating range (V variant) supports deployment in enclosed industrial cabinets without active cooling. When designing with this device, allocate the bottom-side BGA escape region with at least 0.8 mm via-in-pad microvias and 4-layer stack-up to break out the 473-ball map. Multiple voltage rails (1.0 V core, 1.8 V DDR2 VTT, 2.5 V/3.3 V I/O) require careful sequencing - consult the NXP hardware specification for POR and reset timing.

見積もり お問い合わせ
MPC8308VMADDA - PowerQUICC II Pro SoC 266MHz | MAPBGA-473
MPC8308VMADDA

MPC8308VMADDA - PowerQUICC II Pro SoC 266MHz | MAPBGA-473

The NXP MPC8308VMADDA is a PowerQUICC II Pro SoC featuring an e300c3 Power Architecture core running at 266 MHz, packaged in a 473-ball MAPBGA (19x19 mm) with operating temperature range 0C to 105C. It integrates a DDR2 memory controller, PCI Express, Gigabit Ethernet, USB 2.0, and enhanced TSEC networking peripherals in a single chip optimized for low-cost, low-power networking applications. A PowerQUICC II Pro SoC is a system-on-chip that combines a Power Architecture processor core with integrated communications peripherals. Within the broader taxonomy it sits as: microprocessor -> embedded processor -> networking SoC -> PowerQUICC II Pro family -> communications semiconductor. The MPC8308 targets the general embedded networking market where integrated peripherals replace discrete components, reducing bill of materials cost and PCB complexity. Key differentiating features of the MPC8308VMADDA include 266 MHz core frequency, 32-bit Power Architecture e300c3 core, integrated DDR2 memory controller supporting up to 256 MB, dual 10/100/1000 Ethernet controllers with TCP/IP acceleration, PCI Express interface, USB 2.0 host/device, and eSDHC for secure digital storage. The 473-MAPBGA package provides high pin density required for parallel DDR2 and multiple serial interfaces while occupying minimal board area. The MPC8308 architecture combines the e300c3 superscalar core with a unified memory controller and dedicated communications engine. Hardware acceleration offloads DMA, encryption, and packet processing from the core, enabling deterministic throughput for routing, switching, and gateway workloads while maintaining low power consumption typical of the PowerQUICC II Pro family. Typical applications include smart grid home energy gateways, wireless LAN access points, industrial control, networked printers, and IP set-top box controllers. The integrated GbE switch fabric and PCI Express make it particularly well suited for low-cost residential gateways and small office routers where single-chip integration replaces multi-chip designs. When designing with the MPC8308VMADDA, ensure proper power sequencing for the 1.0V core and 1.8V/3.3V I/O rails. The DDR2 memory controller requires matched trace lengths and proper termination. Reference the NXP hardware specification for detailed JTAG, reset, and clock distribution requirements before committing to PCB layout. This page synthesizes distributor pricing, drop-in PowerQUICC II Pro alternatives, and practical embedded design notes not found in the standalone manufacturer datasheet.

見積もり お問い合わせ
MPC8308VMAFD - PowerQUICC II Pro SoC 333MHz e300c3 MAPBGA-473 | NXP
MPC8308VMAFD

MPC8308VMAFD - PowerQUICC II Pro SoC 333MHz e300c3 MAPBGA-473 | NXP

The NXP MPC8308VMAFD is a PowerQUICC II Pro communications processor built on Power Architecture technology, integrating a single e300c3 core running up to 333 MHz within a 473-ball MAPBGA package measuring 19x19 mm. The device combines a 16 KB instruction cache, 16 KB data cache, a DDR2 memory controller capable of 266 MHz data rate, two 10/100/1000 Ethernet MACs with MII/RGMII support, one PCI Express interface, USB 2.0, and a local bus controller on a single low-power SoC. A PowerQUICC (Power Architecture QUICC) processor is a communications-oriented system-on-chip that historically integrated CPU cores with hardware communications peripherals for routing, switching, and protocol offload. The MPC8308 belongs to the PowerQUICC II Pro family, positioned as a cost-effective, low-power, highly integrated host processor for entry-level networking equipment, replacing earlier discrete MCU-plus-MAC designs with a single silicon solution. This makes the part suitable for wired communications infrastructure, industrial control, and embedded networking appliances where Power Architecture toolchains are already deployed. Key features of the MPC8308 include the e300c3 core optimized for low-power 32-bit processing, dual Gigabit Ethernet MACs enabling line-rate switching without external PHY management overhead, PCI Express Gen1 endpoint support for backplane connectivity to companion ASICs, and DDR2 memory support that halves pin count versus DDR1 while doubling peak throughput. The integrated USB 2.0 high-speed interface further reduces BOM by eliminating external USB controllers. Typical applications include industrial Ethernet gateways, networked printers, IP set-top box controllers, sub-routers, factory-floor protocol converters, and SmartGrid endpoint nodes. The 473-MAPBGA footprint exposes the full complement of communications peripherals while keeping board area comparable to a 32-bit MCU with external MACs. For designs already standardized on Power Architecture toolchains, the MPC8308 represents a low-risk upgrade path with mature U-Boot and Linux BSP support. When designing with this part, allocate PCB layers for the BGA breakout (typically a 6- to 8-layer stack with dedicated ground and 1.8V/3.3V power planes). Use the DDR2 controller's fly-by topology for memory, and isolate the PCIe reference clock from the Ethernet PHY clocks to meet jitter masks.

見積もり お問い合わせ
MPC8308VMAGD - PowerQUICC II Pro 400MHz SoC | NXP | Networking
MPC8308VMAGD

MPC8308VMAGD - PowerQUICC II Pro 400MHz SoC | NXP | Networking

The NXP MPC8308VMAGD is a PowerQUICC II Pro integrated host processor based on the Power Architecture e300c3 core, delivering 400 MHz CPU performance in a 473-pin MAPBGA package (19x19 mm, 0.80 mm pitch). It integrates a DDR2 memory controller, PCI Express, Gigabit Ethernet, and USB High-Speed interfaces in a single system-on-chip, targeting cost-sensitive networking and smart-grid gateway applications. A PowerQUICC II Pro SoC (System-on-Chip) is a highly integrated communications processor that combines a CPU core with on-chip peripherals dedicated to packet processing, DMA, and standard I/O. The product family belongs to NXP's MPC83xx series and sits within the broader taxonomy of communications processors -> embedded microprocessors -> integrated circuits -> semiconductors. By collapsing the host CPU, memory controller, and network interfaces into one BGA device, it reduces board area, BOM cost, and power consumption versus multi-chip implementations based on a discrete CPU plus external bridge ASIC. Key features of the MPC8308VMAGD include the e300c3 32-bit Power Architecture core with 16 KB L1 instruction cache and 16 KB L1 data cache, a 32-bit DDR1/DDR2 SDRAM memory controller with ECC, two 10/100/1000 Mbps Ethernet MACs (one RGMII, one MII/RGMII/GMII), one PCI Express Gen1 endpoint/root complex, USB High-Speed host/device/ontroller, local bus controller, and four DMA channels. Security features include a small security engine with DES/3DES/AES/SHA accelerators. The device operates from 0C to 105C ambient and supports industrial temperature networking deployments. The architecture uses a 32-bit SoC platform with dual UART, two I2C, and two SPI interfaces, plus a JTAG TAP for boundary-scan debug. Its on-chip integrated communications engine can offload packet processing tasks from the CPU, freeing the e300c3 core for application-layer logic. The 473-MAPBGA package offers the pin density required for the multi-protocol I/O while keeping the PCB escape manageable with 0.80 mm pitch. Typical applications include smart-grid home energy gateways, residential routers, DSL/VoIP gateways, industrial control with Ethernet connectivity, and entry-level network-attached storage. Designers value the device for its combined Ethernet + PCIe + USB connectivity in a single BGA, which simplifies BOM, layout, and firmware development for connected embedded products. When designing with the MPC8308VMAGD, allocate PCB layers and stackup to maintain signal integrity on DDR2 routes - the 473-BGA requires careful via-in-pad planning and microstrip routing. Thermal management at 400 MHz is straightforward given the part's low-power profile, but ambient-temperature derating must be observed at the 105C upper bound for enclosed consumer enclosures. This page synthesizes distributor pricing, drop-in alternatives from the same MPC8308 family, and practical design notes not found in the manufacturer datasheet.

見積もり お問い合わせ
MPC8308VMAGNA - 400MHz PowerQUICC II Pro, 473-LFBGA | NXP
MPC8308VMAGNA

MPC8308VMAGNA - 400MHz PowerQUICC II Pro, 473-LFBGA | NXP

The NXP MPC8308VMAGNA is a PowerQUICC II Pro communications processor built around the e300c3 PowerPC core running at up to 400 MHz, packaged in a 473-ball LFBGA (19x19 mm) and qualified across the industrial 0C to +105C temperature range. It integrates a high-performance 32-bit CPU, dual 10/100/1000 Ethernet MACs (eTSECs), a DDR2 memory controller, eSDHC, PCI Express, USB 2.0 and local bus interfaces, targeting low-cost, low-power networking and embedded designs. A PowerQUICC II Pro processor is a highly integrated communications SoC that evolved from the original PowerQUICC architecture; it combines a PowerPC host CPU with embedded communications engines (QUICC Engine technology) to offload packet processing. In system hierarchy it sits as a microprocessor (MPU) above generic microcontrollers and below full applications processors, optimized for wired/wireless gateway and data-concentrator workloads where deterministic packet throughput and rich I/O matter more than raw application CPU speed. Key specifications include a 400 MHz e300c3 core with 32 KB I-cache and 32 KB D-cache, 256 KB on-chip SRAM, a 16-bit DDR2 memory controller supporting up to 256 MB of addressable memory, two enhanced TSEC Gigabit Ethernet controllers, a PCI Express Gen 1.0 endpoint/root complex port, USB 2.0 High-Speed host/device, eSDHC, SPI, DUART, I2C and GPIO. Security is provided by a SEC 2.2 accelerator supporting DES/3DES, AES and hashing. The device operates from a 1.0 V core supply with 3.3 V I/O, consuming roughly 1 W typical at 400 MHz. The MPC8308 extends the PowerQUICC family with higher CPU performance and faster interfaces versus older MPC8323/MPC8347 designs, while addressing cost, power and time-to-market constraints. It uses a coherent system bus to keep the QUICC Engine and e300c3 core synchronized, and exposes both multiplexed and non-multiplexed local-bus modes for legacy glue-less peripherals. Typical applications include smart-grid home energy gateways, data concentrators, wireless LAN access points, femtocell base stations, consumer printers and industrial controllers/factory-automation nodes. It is also commonly used in low-end routers and protocol-conversion gateways where dual GbE plus PCI Express enable flexible line-card designs. Design consideration: the LFBGA-473 (19x19 mm) requires a 6+ layer PCB with microvia stack-ups for breakout; thermal design is straightforward at ~1 W typical but the user must respect DDR2 routing rules (matched lengths, VTT termination) and provide a clean 1.0 V core rail to keep Tj below the 105C industrial limit. Provision an external PHY for each eTSEC and ensure the 25 MHz system reference clock meets jitter requirements. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving procurement and design engineers a one-stop reference for the MPC8308VMAGNA.

見積もり お問い合わせ
MPC8309VMAGDCA557 - PowerQUICC II Pro 400MHz e300c3 | NXP
MPC8309VMAGDCA557

MPC8309VMAGDCA557 - PowerQUICC II Pro 400MHz e300c3 | NXP

The NXP MPC8309VMAGDCA557 is a PowerQUICC II Pro integrated communications processor built around the e300c3 PowerPC core, delivering up to 400 MHz of performance in a 489-ball MAPBGA package (19x19 mm). Designed for cost-effective multi-protocol networking control, the device integrates a high-performance CPU, a flexible QUICC Engine communication subsystem, DDR2 memory controller, dual Gigabit Ethernet MACs, PCI Express, and USB 2.0 peripherals on a single die. The MPC8309 PowerQUICC II Pro Integrated Communications Processor Family belongs to the MPC830x series - cost-effective network communication processors that meet the requirements of multi-protocol control applications. As a PowerQUICC II Pro device, it provides better CPU performance, additional functionality, and faster interfaces than legacy PowerQUICC II processors while addressing important time-to-market, price, power consumption, and board real estate constraints for embedded designs. Key features include the e300c3 core with 32 KB level-1 instruction and data caches, hardware floating-point and MMU support, hardware cryptography acceleration (SEC 2.x compatible), DDR1/DDR2 memory controller with 32-bit data path, dual 10/100/1000 Ethernet MACs, PCI Express (one x4 or two x1), USB 2.0 high-speed host/device, two local buses, and a QUICC Engine subsystem supporting up to 32 TDM/HDLC channels for legacy telecom protocols. The architecture combines a classic PowerPC processor with an on-chip RISC-based communication engine, allowing protocol processing to be offloaded from the main CPU. This partitioning enables deterministic throughput for packet-intensive tasks while leaving the host CPU free for control-plane processing, making it suitable for SOHO and SMB routers, VPN gateways, and industrial control applications. Typical applications include residential gateways, integrated access devices, DSL/cable modems, SOHO routers, VPN/firewall appliances, industrial serial-to-IP gateways, and embedded control platforms with deterministic networking requirements. The QUICC Engine enables seamless migration from legacy MPC8xx designs while modernizing the peripheral set. When designing with this device, ensure adequate PCB thermal management and follow NXP's hardware specifications document for DDR2 layout, reference voltage decoupling, and SerDes routing. Programming requires the standard PowerPC toolchain (GCC + ELDK or vendor IDE) and proper JTAG access for debug. This page synthesizes distributor pricing, drop-in alternatives within the MPC830x family, and practical design considerations not found in the manufacturer datasheet alone.

見積もり お問い合わせ
MPC8313CVRADDB - PowerQUICC II Pro 267MHz MPU | NXP 516-BGA
MPC8313CVRADDB

MPC8313CVRADDB - PowerQUICC II Pro 267MHz MPU | NXP 516-BGA

The NXP MPC8313CVRADDB is a PowerQUICC II Pro microprocessor unit (MPU) based on the PowerPC e300c3 core, delivering a 267 MHz core clock in a 516-ball TEPBGA (27x27 mm) package without encryption. It is part of NXP's MPC8313 family targeted at cost-sensitive networked applications where an integrated communications engine reduces BOM and software complexity. A microprocessor (MPU) is an integrated circuit that integrates a central processing unit, memory controller, and peripheral subsystems on a single die. Within the broader taxonomy, the MPC8313CVRADDB sits as: MPU -> embedded processor -> microprocessor -> integrated circuit -> semiconductor. The PowerQUICC II Pro line historically serves networking, storage, and industrial control designs that benefit from on-chip QUICC Engine communications acceleration. Key features include a 32-bit PowerPC e300c3 core running at 267 MHz, integrated DDR1/DDR2 memory controller, dual 10/100/1000 Ethernet MACs, USB 2.0 (High-Speed) with on-chip PHY, PCI Express interface (one x1 lane), and a dedicated QUICC Engine communications accelerator. The 516-ball TEPBGA package exposes the full peripheral set while providing manageable thermal characteristics for industrial-grade deployments. The device uses a 32-bit superscalar e300 core derived from the Power Architecture, with separate instruction and data MMUs and hardware table-walk support. The QUICC Engine offloads protocol processing (e.g., HDLC, ATM, IEEE 1588 timestamping) from the main core, allowing wire-rate handling of multiple serial interfaces including TDM, UART, and SPI. This hardware partitioning is what historically differentiated PowerQUICC from generic ARM SoCs in the same era. Typical applications include industrial routers and gateways, networked printers, factory automation controllers, branch-office routers, and storage area network (SAN) controllers. Designers value the MPC8313 family for its long-lived NXP/Freescale software support and proven reliability in 24/7 networking equipment. When designing with this part, allocate adequate PCB area for the 27x27 mm BGA footprint with microvia stack-up, and plan thermal dissipation assuming industrial ambient temperatures. DDR2 termination, reference voltage, and impedance-controlled routing are required for signal integrity. This page synthesizes distributor pricing, drop-in alternatives within the MPC8313 family, and practical design notes not found in the manufacturer datasheet alone.

見積もり お問い合わせ
MPC8313CVRADDC - PowerQUICC II Pro e300c3 MPU, 266 MHz | NXP
MPC8313CVRADDC

MPC8313CVRADDC - PowerQUICC II Pro e300c3 MPU, 266 MHz | NXP

The NXP MPC8313CVRADDC is a PowerQUICC II Pro integrated communications processor built around a single-core PowerPC e300c3 CPU operating at 267 MHz with a 32-bit architecture, housed in a 516-ball TEPBGA package measuring 27 mm x 27 mm. The device integrates DDR1/DDR2 memory controllers, a PCI interface, Gigabit Ethernet MAC, USB 2.0, and an integrated security engine (SEC) disabled in this variant, providing a complete system-on-chip for cost-sensitive networking and connected-media applications. A PowerQUICC II Pro processor is a member of the Power Architecture communications SoC family - a derivative of the original PowerQUICC line that integrates a CPU core with communications peripherals so that a single chip can run protocol stacks, drive external PHYs, and manage DDR memory. In the broader taxonomy, MPC8313E sits under PowerQUICC II Pro -> PowerQUICC -> Power Architecture SoC -> communications processor -> embedded microprocessor -> integrated circuit. The device supports the digital home, SMB NAS, and industrial control markets where deterministic Ethernet throughput and PCI expansion matter. Key features include 266 MHz core frequency, 32 KB instruction and 32 KB data L1 caches, double-precision FPU, integrated MMU, DDR1/DDR2 memory controller up to 333 MHz, dual 10/100/1000 Mbps Ethernet MACs (GMACs), one MII/RMII/RGMII interface, USB 2.0 high-speed host/device/OTG, two PCI 2.3 controllers (one 32-bit, one mini-PCI), local bus with NAND flash support, four UARTs, two I2C, two SPI, and an operating range of -40C to +105C. Power dissipation is approximately 2.0 W typical under full load. The MPC8313C uses a 90 nm CMOS process and a superscalar e300 core that executes the Power Architecture Book E instruction set, with hardware hashing and DMA engines that offload packet processing. Code compatibility with older MPC8349/8343 designs allows straightforward firmware reuse, and the DDR2 controller with ECC support enables reliable operation of u-boot and Linux BSPs available from NXP and the open-source community. Typical applications include SMB network attached storage, connected media gateways, home gateways and routers, factory automation controllers, industrial printers, industrial robotics and motion control, and PCI-based embedded expansion boards. The combination of GbE, USB, PCI, and DDR2 in a single BGA package removes the need for an external memory controller hub and reduces BOM cost on multi-board platforms. When designing with this device, place four-layer PCB stackup with a continuous ground plane beneath the BGA, and use controlled-impedance routing for DDR2 and RGMII. Power sequencing must follow the NXP hardware specification because incorrect order on core and IO rails can latch-up the device. JTAG and BDI2000/CodeWarrior TAP probes are required for production board bring-up. This page synthesizes distributor pricing from DigiKey, Mouser and LCSC, drop-in alternatives from the same MPC83xx family, and engineering notes not collected in the manufacturer's datasheet PDF.

見積もり お問い合わせ
MPC8313CZQADDC - PowerQUICC II Pro MPU 267MHz | TI
MPC8313CZQADDC

MPC8313CZQADDC - PowerQUICC II Pro MPU 267MHz | TI

The NXP Semiconductors (formerly Freescale) MPC8313CZQADDC is a PowerQUICC II Pro communications processor built on the PowerPC e300c3 core, integrating a 32-bit RISC CPU running at up to 267 MHz with a 516-ball TEPBGA (27x27 mm) package. It belongs to the MPC8313 family, Revision 3 silicon, and is qualified for industrial temperature operation from -40C to +105C. The device combines CPU, DDR1/DDR2 memory controller, PCI/PCI-X, Gigabit Ethernet, USB 2.0, and security acceleration in a single system-on-chip. A PowerQUICC communications processor is a category of integrated Power Architecture SoCs originally developed by Motorola (later Freescale, now NXP) that consolidate a PowerPC CPU core with communication peripherals such as Ethernet MACs, PCI interfaces, and memory controllers. The MPC8313 sits in the lower-power tier of the PowerQUICC II Pro family and is commonly used in wired networking and embedded control applications where deterministic performance and integrated connectivity outweigh raw MHz. Key features include up to 267 MHz e300c3 core frequency, 16 KB I-cache and 16 KB D-cache, integrated DDR1/DDR2 SDRAM controller with ECC support, dual 10/100/1000 Ethernet MACs (one with GMII/TBI/RGMII, one with GMII/MII/RGMII), two PCI/PCI-X controllers, USB 2.0 (Host + Device), local bus, DMA, and a security engine. The integrated peripherals allow a complete line-card or small-router BOM with only the MPC8313, PHY, memory, and magnetics. The architecture leverages a unified 32-bit peripheral bus plus separate DMA channels for I/O, offloading memory transfers from the CPU and improving sustained throughput. The e300c3 core is a low-power variant of the e500 family, providing predictable integer performance with low heat dissipation suitable for fanless industrial enclosures. The 516-TEPBGA package provides the high-density interconnect needed for the 32-bit memory and 16-bit local-bus interfaces. Typical applications include SOHO and SMB routers, integrated access devices, DSLAM line cards, industrial gateways, secure point-of-sale terminals, and PowerPC-based embedded control. The DDR1/DDR2 controller and dual GbE MACs make the device well suited to small-office networking appliances requiring line-rate packet processing without an external switch. When designing with this part, allocate a 4-layer or 6-layer PCB to route the 32-bit DDR memory bus with proper impedance control and length matching. The TEPBGA package requires 0.8 mm or 1.0 mm ball pitch PCB land pattern and precise reflow profile to avoid head-in-pillow defects; NXP's hardware specification document is the authoritative reference for layout rules. Designers should also verify boot ROM configuration and pin strapping resistors at design bring-up. This page synthesizes NXP datasheet parameters, current distributor pricing, and drop-in same-family alternatives not found in the manufacturer literature, providing context for sourcing and PCB reuse decisions.

見積もり お問い合わせ