AD611KH/+ - 13 V/µS Operational Amplifier | Analog Devices
部品番号: AD611KH/+ ✓ 生産中AD611KH/+ 概要
An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify the difference between two input voltages. The voltage-feedback architecture used by the AD611KH/+ is commonly used with resistive negative feedback to set closed-loop gain. Because negative feedback determines signal gain, bandwidth, output swing, and stability, the amplifier must be evaluated with the same feedback network and load conditions used in the intended circuit.
The AD611KH/+ provides a slew rate of 13 V/µs, making its large-signal response faster than the slew rate of many general-purpose amplifiers. This characteristic is particularly relevant when processing moderate-amplitude step signals, waveform edges, and signals requiring low full-power-bandwidth distortion. The operating context remains important: the 13 V/µs figure describes maximum rate of change, while output swing, load capability, noise, input bias current, and stability determine whether the amplifier can realize that performance in a practical circuit.
The AD611KH/+ operates from dual supplies identified as ±15 V. This conventional supply arrangement supports bipolar input and output signal excursions around the midpoint of the supply rails. Designers must confirm the output-current capability and output-voltage swing before driving resistive, capacitive, or load-connected circuits. Decoupling capacitors should be positioned close to the device pins, and the layout should minimize feedback-loop area and sensitive-input-node capacitance.
Typical applications include analog signal conditioning, instrumentation amplifiers, active filters, waveform shaping, closed-loop amplifier stages, and laboratory or industrial measurement systems. Its 13 V/µs slew rate supports applications where edge accuracy and distortion control matter, while the TO-99-8 package remains useful for legacy systems, modular analog assemblies, and designs that use hermetic metal-can operational amplifiers.
The primary design trade-off is package practicality. The TO-99-8 package is mechanically durable and compatible with through-hole assembly, but it occupies more PCB area than a modern surface-mount package and requires manual insertion. Verify the eight-terminal pin assignment in the manufacturer datasheet before constructing a PCB or replacing an existing device.
This product record consolidates the confirmed electrical identity, package information, commercial sourcing context, application guidance, and design cautions for the AD611KH/+. It also identifies the unavailable parameters that should be checked in the manufacturer datasheet before precision, low-noise, high-current, or temperature-critical designs are released.
ドロップイン代替品: AD611KH/+ — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
この製品に利用可能なドロップイン代替品はありません。
代替品をリクエストAD611KH/+ 最大定格&電気的特性
| Product Type | General-purpose voltage-feedback operational amplifier |
| Manufacturer | Analog Devices |
| Slew Rate | 13 V/µs |
| Power Supplies | ±15 V |
| Temperature Grade | Commercial |
| Terminal Form | Wire |
| Number of Terminals | 8 terminals |
| Package Shape | Round |
| パッケージ | TO-99-8 metal can |
| 実装タイプ | Through-hole |
| Feedback Architecture | Voltage feedback |
| RoHS ステータス | Non-compliant |
AD611KH/+ to-99-8 metal can ピン配置ガイド
AD611KH/+ (to-99-8 metal can パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: AD611KH/+.
詳細は データシート をご参照ください。
主な用途
AD611KH/+ の用途: 6 件s: Precision Closed-Loop Signal Amplification, Active Filter Stages, Instrumentation and Measurement Front Ends, Waveform Shaping and Edge Processing, Legacy Through-Hole Analog Modules, Industrial Control Signal Conditioning.
Precision Closed-Loop Signal Amplification
The AD611KH/+ is appropriate for a closed-loop gain stage in which a differential input must be amplified around a zero-volt reference. Its 13 V/µs slew rate allows the output to follow moderate step changes more rapidly than the response of a slow general-purpose amplifier, helping reduce edge distortion. The circuit should use negative feedback to establish gain, while the designer verifies input common-mode range, output swing, and load stability against the ±15 V supply arrangement before selecting resistor values.
Active Filter Stages
The AD611KH/+ can serve as the active element in analog low-pass, high-pass, or band-pass filter stages. Its 13 V/µs slew rate improves large-signal behavior in filters exposed to periodic waveform edges, while the feedback network determines the nominal response. Component tolerances and the amplifier’s gain-bandwidth interaction remain central to frequency accuracy, so simulate the complete stage and check stability with the intended load and source impedance.
Instrumentation and Measurement Front Ends
The AD611KH/+ is suitable for an instrumentation or measurement front end that amplifies a sensor-derived voltage before conversion or processing. The dual ±15 V supplies support bipolar signals around ground, and the 13 V/µs slew rate provides useful dynamic headroom for rapidly changing sensor outputs. Actual measurement accuracy still depends on input offset, input bias current, noise, common-mode limits, and resistor matching, so those characteristics must be obtained from the manufacturer datasheet.
Waveform Shaping and Edge Processing
The AD611KH/+ can be used in waveform-shaping, comparator-like conditioning, or edge-processing circuits where a relatively quick output transition is valuable. Its specified 13 V/µs slew rate limits how quickly the output can follow a large step and helps distinguish this amplifier from slower general-purpose devices. Designers should account for finite output swing around the ±15 V rails and use feedback or limiting arrangements that keep the requested waveform within the amplifier’s operating range.
Legacy Through-Hole Analog Modules
The eight-terminal TO-99-8 metal-can package makes the AD611KH/+ well suited to legacy analog modules, laboratory instruments, and hand-assembled through-hole boards. The round metal can provides a mechanically distinct option from common plastic DIP operational amplifiers, but it also requires more PCB area and manual insertion. Production drawings should follow the manufacturer package dimensions and pin numbering exactly rather than relying on a generic eight-pin operational-amplifier footprint.
Industrial Control Signal Conditioning
The AD611KH/+ can condition low-level industrial signals in a controlled analog module when its electrical limits match the system requirements. Its 13 V/µs slew rate supports signals with sharper transitions, and its ±15 V supply arrangement is common in older control equipment. For factory use, evaluate noise, offset drift, common-mode range, output loading, and temperature behavior against the enclosure environment before approving a long-life production design.
エンジニアリング参考データ: AD611KH/+ — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 |
|---|---|
| Brand | Analog Devices |
| Package | TO-99-8 metal can |
| Terminal Count | 8 terminals |
| Mounting Type | Through-hole |
| Feedback Architecture | Voltage feedback |
| Slew Rate | 13 V/µs |
| Power Supplies | ±15 V |
| Temperature Grade | Commercial |
主な差別化要因
- Through-hole hermetic-style mechanical package (vs AD611KH/+)
- Clearly identified general-purpose performance (vs AD611KH/+)
- Conventional dual-rail operation (vs AD611KH/+)
設計ノート
Place the supply-decoupling capacitors close to the appropriate device pins and keep their ground returns short. Route the high-impedance input node before the feedback resistors, because parasitic capacitance at that node can reduce phase margin and alter the closed-loop response. Use a low-impedance ground reference and avoid long loops between the amplifier, its feedback network, and bypass capacitors.
Do not treat any operational amplifier with an eight-terminal metal can as an automatic substitute for the AD611KH/+. Before replacement, confirm the TO-99-8 mechanical outline, terminal numbering, input and output assignments, supply pins, common-mode range, and output swing. Also compare noise, offset voltage, bias current, unity-gain bandwidth, slew rate, and stability with the existing feedback network and load.
Use the AD611KH/+ within its identified ±15 V dual-supply arrangement and provide local bypassing at the device. When calculating allowable output excursion, include transistor headroom, load-related output shift, and signal overshoot rather than treating the supply rails as exact clipping limits. The confirmed 13 V/µs slew rate defines a rate of change, not the maximum output voltage or output-current capability.
コンプライアンス情報
The RoHS status is listed as non-compliant for this metal-can package. Other environmental and material-compliance fields are unknown and require confirmation with the manufacturer.