AD7451ARM - 12-Bit 1 MSPS SAR ADC | Analog Devices
部品番号: AD7451ARM ✓ 生産中AD7451ARM 概要
An analog-to-digital converter converts a continuous analog voltage into a digital code. A SAR ADC performs this task by successively comparing the sampled input with an internal or external reference and generating one output bit per comparison cycle. The AD7451 belongs to the ADC and DAC category within the broader analog and mixed-signal IC family, combining a sampling network, comparator, reference interface, and digital output stage in one compact device.
Key characteristics include 12-bit resolution, a 1 MSPS sampling rate, and a pseudo-differential analog input. The serial conversion process is controlled by the active-low CS input and an external serial clock, allowing the converter to communicate directly with microcontrollers, DSPs, or other serial acquisition systems. The external reference interface accommodates reference voltages from 100 mV up to the device supply voltage, so full-scale scaling can be matched to the sensor, transducer, or conditioned signal being measured.
The AD7451 uses the charge-redistribution architecture typical of SAR converters. Each conversion acquires the input on an internal capacitor array and then resolves 12 binary-weighted decisions. This architecture offers predictable sampling behavior, straightforward digital interfacing, and good suitability for moderate-speed instrumentation. Because conversion time is 16 us, a sustained 1 MSPS operating rate requires careful clock and data-capture timing as well as attention to the serial interface cycle budget.
Typical uses include industrial process monitoring, portable measurement systems, sensor-interface boards, battery-powered instruments, and embedded data-acquisition modules. The part is also appropriate when a microcontroller needs a dedicated high-resolution ADC for temperature, pressure, current, or analog-front-end measurements. Its small 8-lead MSOP package supports compact layouts, although the narrow lead pitch requires careful solder-paste control and inspection.
Designers should treat the reference voltage as a precision analog node. Keep the REFIO or external reference connection short, place bypass capacitance at the supply pins, and route serial clock and data traces away from the analog input. Confirm signal polarity, common-mode range, acquisition timing, and code format against the manufacturer datasheet before integrating the converter into a new board.
This page combines the manufacturer specifications, package information, ordering details, and cross-reference findings with practical guidance for interface timing, reference design, layout, and replacement decisions.
ドロップイン代替品: AD7451ARM — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
AD7451ARMZ
✅ ドロップイン📋 参考代替品(カタログ未掲載)
ADS7834E/250G4
✅ ドロップイン📋 参考代替品(カタログ未掲載)
AD7451ARM 最大定格&電気的特性
| 分解能 | 12 bit |
| サンプリングレート | 1 MSPS |
| Conversion Time | 16 us |
| Architecture | Successive approximation (SAR) |
| Input Channel Count | 1 channel |
| Input Type | Pseudo-differential |
| Supply Configuration | Single supply, 3 V or 5 V |
| External Reference Voltage Range | 100 mV to VDD |
| Digital Interface | Serial, controlled by active-low CS and serial clock |
| 動作温度範囲 | -40C to +85C |
| パッケージ | 8-lead MSOP |
| Lead Count | 8 leads |
| 実装タイプ | Surface mount |
| Product Lifecycle | Production |
AD7451ARM 8-lead msop ピン配置ガイド
AD7451ARM (8-lead msop パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: AD7451ARM.
詳細は データシート をご参照ください。
主な用途
AD7451ARM の用途: 6 件s: Industrial Process Sensing, Portable Measurement Instruments, Embedded Data-Acquisition Module, Battery Current and Power Monitoring, Industrial Automation and Control Loops, Test and Measurement Front Ends.
Industrial Process Sensing
The AD7451ARM is suitable for monitoring pressure, temperature, level, and current signals in industrial process-control equipment. Its 12-bit resolution and 1 MSPS conversion capability provide useful resolution for slow process variables while leaving sampling headroom for multiplexed channels or transient detection. The pseudo-differential input is useful when the conditioning stage can provide a return or correction signal. Place the converter behind a low-noise amplifier, use the external reference range to match the transducer output, and check the acquisition timing against the required sensor update interval.
おすすめ
Portable Measurement Instruments
Battery-powered meters and field-measurement devices can use the AD7451ARM to acquire slow analog inputs without adding a large converter footprint. The 8-lead MSOP package supports compact instrument boards, and the single 3 V or 5 V operation aligns with many embedded analog systems. The 12-bit code width is appropriate for many battery, current, and resistive sensor measurements. Reference current, converter power consumption, and sleep-mode behavior should be included in the overall battery budget before finalizing the analog architecture.
おすすめ
Embedded Data-Acquisition Module
The AD7451ARM fits modular data-acquisition cards that expose analog measurements to a microcontroller, DSP, or FPGA. A 1 MSPS sampling rate supports faster sampling than conventional slow-resolution converters, while the 16 us conversion time allows sequential acquisition when multiple sources are multiplexed. The serial interface keeps the pin count low and reduces parallel-bus routing. Validate setup time, chip-select behavior, clock polarity, and data-capture latency in the system timing diagram.
おすすめ
Battery Current and Power Monitoring
The AD7451ARM can digitize outputs from current-sense amplifiers in energy-monitoring and battery-analysis systems. Its 12-bit resolution supports incremental measurement of charge and discharge current, and the 1 MSPS rate can capture current transients that occur during load switching. The pseudo-differential input arrangement can accept the sense-amplifier output and a reference-side signal for correction. Keep the sense path away from the digital clock and use the external reference range to optimize the available converter span.
おすすめ
Industrial Automation and Control Loops
The AD7451ARM is appropriate for feedback monitoring in industrial automation systems where analog process values must be converted for a controller. The 1 MSPS sampling capability is well matched to many temperature, pressure, and actuator-position loops, while the 12-bit resolution limits quantization error relative to an 8-bit converter. Use the pseudo-differential arrangement to reject common-mode offsets in the conditioning stage, and specify reference accuracy carefully because reference error appears directly in the converted result.
おすすめ
Test and Measurement Front Ends
The AD7451ARM can serve as the conversion stage in a compact laboratory or field-test instrument that measures low-level analog quantities. The 12-bit resolution provides a practical balance between resolution, conversion speed, and circuit complexity, while the serial output simplifies connection to a digital instrument controller. Place a low-noise input buffer directly ahead of the converter, minimize trace length around the reference node, and apply shielding or grounding techniques appropriate to the expected signal level and source impedance.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: AD7451ARM — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | AD7451ARMZ | ADS7834E/250G4 |
|---|---|---|---|
| Package | 8-lead MSOP | 8-lead MSOP | 8-lead MSOP |
| Brand | Analog Devices | Analog Devices | Texas Instruments |
| Resolution | 12 bit | 12 bit | 12 bit |
| Sampling Rate | 1 MSPS | 1 MSPS | 1 MSPS |
| ADC Architecture | Successive approximation (SAR) | Successive approximation (SAR) | Successive approximation (SAR) |
| Input Channel Count | 1 channel | 1 channel | 1 channel |
主な差別化要因
- Same-branded ordering option retains the complete converter function (vs AD7451ARMZ)
- Documented cross-brand conversion capability (vs ADS7834E/250G4)
- Pseudo-differential input architecture (vs ADS7834E/250G4)
設計ノート
Route the analog input and reference connections away from the serial clock and data traces, and place input bypass capacitance at the converter supply pins. Because this package has a narrow lead pitch, define a stable solder-paste stencil and inspect the analog and digital leads separately during manufacturing. Use the manufacturer's application circuit as the basis for separating sensitive analog routing from the chip-select and clock paths.
The 1 MSPS maximum throughput and 16 us conversion time require a complete timing budget that includes acquisition, conversion, clocking, and output transfer. Confirm chip-select polarity, clock edge requirements, output settling, and microcontroller or DSP capture latency from the manufacturer timing diagrams. These checks are more important than adding large bulk capacitance because excessive lead length or an unsuitable clock arrangement can dominate converter accuracy.
Treat the reference node as part of the measurement chain. A reference error contributes directly to gain error, so use the reference range of 100 mV to VDD to maximize the converter's usable input span while respecting the reference-source requirements. Keep the reference trace compact, place its recommended bypass capacitor at the pin, and isolate the reference from high-current return paths in the PCB stack-up.
コンプライアンス情報
The AD7451 family is listed as a production product by Analog Devices. RoHS, REACH, halogen-free, and conflict-minerals declarations are not stated in the product information and remain unknown until confirmed on the manufacturer product page or in a current compliance document.