AD8005ARZ - 170MHz Low-Power Current-Feedback Amplifier | Analog Devices
部品番号: AD8005ARZ ✓ 生産中AD8005ARZ 概要
A current-feedback amplifier is a voltage-feedback amplifier architecture in which the closed-loop bandwidth can remain relatively wide as gain increases, provided the feedback resistor is selected according to the manufacturer’s recommended values. The AD8005 combines this architecture with low quiescent current and a low-power operating range, helping preserve battery life while providing substantially more bandwidth than a conventional precision op amp.
The AD8005ARZ features a wide signal bandwidth of 170 MHz, a slew rate of 280 V/µs, and gain flatness of 0.1 dB through 30 MHz. Its 400 µA quiescent supply current is particularly useful in portable systems where amplifier power consumption directly affects available operating time. The device also supports operation from a single 5 V supply or dual supplies, allowing it to interface with systems using modern mixed-signal power rails.
The current-feedback topology is particularly appropriate for high-speed buffers, video-signal paths, analog-to-digital converter input stages, and communications circuits where conventional voltage-feedback amplifiers can suffer bandwidth reduction as gain increases. The AD8005’s combination of high speed and low supply current makes it useful in portable test equipment, low-power imaging systems, and battery-operated measurement platforms.
The most important design consideration is the feedback network. Use the resistor values and gain configuration shown in the AD8005 manufacturer datasheet, and place the feedback components close to the amplifier pins to minimize parasitic capacitance. Decoupling capacitors should be positioned directly beside the supply pins, with a short return path to minimize supply noise and high-frequency instability.
This product page combines the AD8005ARZ electrical characteristics with application guidance, design notes, pricing references, and pin-compatible alternatives. It is intended to help engineers identify the correct amplifier for portable, high-speed, and low-power analog systems while preserving the same SOIC-8 board footprint.
ドロップイン代替品: AD8005ARZ — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
AD8055
✅ ドロップイン📋 参考代替品(カタログ未掲載)
AD8056
✅ ドロップイン📋 参考代替品(カタログ未掲載)
AD8005ARZ 最大定格&電気的特性
| Amplifier Type | Current-feedback amplifier |
| Number of Circuits | 1 circuit |
| Signal Bandwidth | 170 MHz |
| Slew Rate | 280 V/µs |
| Quiescent Supply Current | 400 µA |
| Gain Flatness | 0.1 dB through 30 MHz |
| 電源電圧 | 5 V |
| Common-Mode Rejection Ratio | 54 dB |
| 動作温度 | -40 °C to +85 °C |
| Package Type | 8-pin SOIC |
| 実装タイプ | Surface mount |
AD8005ARZ 8-pin soic ピン配置ガイド
AD8005ARZ (8-pin soic パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: AD8005ARZ.
詳細は データシート をご参照ください。
主な用途
AD8005ARZ の用途: 6 件s: Portable High-Speed Measurement, High-Speed ADC Signal Conditioning, Battery-Powered Communications, Video Signal Buffering, Industrial Sensor Interfaces, Low-Power Test and Measurement.
Portable High-Speed Measurement
The AD8005ARZ fits portable measurement equipment because it combines a 170 MHz signal bandwidth with only 400 µA of quiescent supply current. Place the device close to the sensor or converter being measured to preserve high-frequency content without adding substantial standing power demand. Its current-feedback architecture is useful for fixed-gain and moderate-gain signal paths, while the 280 V/µs slew rate helps preserve large-signal performance. Check the required output swing, load capacitance, and feedback resistor values for the selected gain before finalizing the circuit.
おすすめ
High-Speed ADC Signal Conditioning
Use the AD8005ARZ to condition signals entering a high-speed ADC when the converter requires more bandwidth or slew capability than a general-purpose amplifier can provide. Its 170 MHz signal bandwidth and 280 V/µs slew rate support high-bandwidth acquisition paths, while the low 400 µA quiescent current helps preserve portable-system operating time. Because the device uses current feedback, select the feedback resistor from the manufacturer’s gain table and validate settling behavior with the actual ADC input network, source impedance, and sampling clock.
おすすめ
Battery-Powered Communications
The AD8005ARZ is appropriate for battery-powered communication modules that need signal amplification without the power draw of a conventional high-speed voltage-feedback amplifier. Its 400 µA quiescent current is especially useful in intermittent or always-on portable links, while 170 MHz bandwidth provides margin for high-speed data paths. Confirm that the amplifier’s supply voltage, output swing, and drive capability match the transmitter or receiver interface. Keep the feedback network compact and use local supply decoupling to maintain low-noise operation.
おすすめ
Video Signal Buffering
The AD8005ARZ can serve as a high-speed buffer in compact video and imaging systems where the required bandwidth exceeds ordinary precision op-amp capabilities. Its 170 MHz bandwidth, 280 V/µs slew rate, and 0.1 dB gain flatness through 30 MHz help preserve signal integrity across the analog path. The current-feedback topology is useful for maintaining bandwidth as gain increases, but the feedback resistor must follow the datasheet recommendations. Account for video timing, output loading, connector capacitance, and the allowable propagation delay of the complete system.
おすすめ
Industrial Sensor Interfaces
The AD8005ARZ is useful for industrial sensor interfaces that must preserve high-frequency content while keeping amplifier consumption low. A sensor front end may use the device as a gain stage or buffer before a converter or controller, benefiting from the 170 MHz bandwidth and 280 V/µs slew rate. The 400 µA quiescent current is valuable in distributed or battery-backed sensing nodes. Verify sensor output range, common-mode voltage, noise requirements, and grounding strategy because the available device data does not specify every input and output limit for every operating condition.
おすすめ
Low-Power Test and Measurement
The AD8005ARZ fits portable oscilloscope, probe-interface, and general-purpose test equipment where bandwidth and power must be balanced. Its 170 MHz signal bandwidth can support fast-edge measurement and signal-conditioning paths, while 400 µA quiescent current helps extend battery-powered instrument runtime. Use the current-feedback gain and resistor recommendations from the manufacturer and keep the input network short. For a permanent instrument design, verify thermal performance, output drive into the probe or converter load, and the required settling time over the full measurement bandwidth.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: AD8005ARZ — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | AD8055 | AD8056 |
|---|---|---|---|
| Package | SOIC-8 | SOIC-8 | SOIC-8 |
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Amplifier Type | Current-feedback amplifier | Current-feedback amplifier | Current-feedback amplifier |
| Number of Circuits | 1 circuit | 1 circuit | 1 circuit |
主な差別化要因
- Lower quiescent current for portable designs (vs AD8055)
- High-speed bandwidth with low standby power (vs AD8056)
- Gain flatness across the mid-band (vs AD8055)
設計ノート
Place the feedback resistor and associated compensation or gain-setting components close to the AD8005ARZ pins, especially when operating at high speed. Keep the input and output traces short, avoid routing sensitive nodes beneath the device, and return the bypass-capacitor ground directly to the ground pin. Current-feedback amplifiers are sensitive to parasitic capacitance in the feedback loop, so a compact layout can be more important than a nominally correct but physically large resistor arrangement.
Use local supply decoupling and follow the manufacturer’s recommended capacitor values. Place the input capacitor directly beside the positive supply pin and the ground capacitor beside the ground connection, with minimal loop area. The AD8005ARZ’s low 400 µA quiescent current reduces standing power, but the complete design should still check supply noise, output-current capability, and the voltage drop caused by wiring resistance during transient load events.
Do not select the feedback resistor by applying voltage-feedback amplifier design rules. Use the AD8005 manufacturer’s gain-versus-feedback-resistance recommendations and account for the actual source impedance, load capacitance, and target gain. Also verify that the 8-pin SOIC pin assignment matches the selected amplifier configuration before routing the PCB, because the same package family can contain amplifier variants with different operating or disable functions.
コンプライアンス情報
Compliance status was not explicitly stated in the available product information. Confirm the current declarations and package material documentation with Analog Devices before release to production.