ADC121S101CIMFX - 12-Bit 1MSPS SAR ADC | Texas Instruments
部品番号: ADC121S101CIMFX ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $3.92 | $3.92 |
| 10 | $3.45 | $34.50 |
| 100 | $2.99 | $299.00 |
| 500 | $2.55 | $1,275.00 |
| 1,000 | $2.18 | $2,180.00 |
| 3,000 | $1.85 | $5,550.00 |
ADC121S101CIMFX 概要
An SAR ADC is a type of analog-to-digital converter that uses a binary-search algorithm implemented by a switched-capacitor DAC and a comparator, settling one bit per clock cycle and providing a deterministic, low-latency conversion result with no pipeline delay. SAR ADCs sit within the broader data-converter hierarchy alongside delta-sigma, pipeline, and flash converters; they are favored for multiplexed acquisition, motor control, and instrumentation front-ends where low latency and small package size outweigh the need for very high sample rates or channel count.
Key differentiating features of the ADC121S101 include a true-differential input span of 0V to VA on the SOT-23 variant, an external reference input (VA can be used as the reference), and an SPITM-compatible serial interface that uses a chip-select bar (CS) framing signal, allowing multiple devices to share a single bus. The small footprint and the wide supply range (2.7V to 5.25V) make it a drop-in upgrade path for legacy 8-bit and 10-bit SAR designs in the same footprint, including the pin-compatible ADC081S101 and ADC101S101 family members. The 6-pin SOT-23 form factor is approximately 1.6 mm wide and is compatible with high-density PCBs and dense analog front-end layouts.
Typical applications include portable instrumentation, factory automation modules, optical-module monitoring, and low-power data-acquisition front-ends where the combination of 12-bit resolution and 1 MSPS throughput is sufficient. The wide operating temperature range of -40C to +125C and the lead-free/RoHS-compliant package support industrial designs that must operate under harsh thermal and regulatory conditions.
When designing with this converter, place the 0.1 µF supply decoupling capacitor as close as possible to pin VA, keep the analog input traces short and guarded, and ensure the serial clock edges are clean to avoid digital-feedthrough coupling into the analog domain. For absolute best linearity, drive VA from a low-noise reference rather than reusing it as both supply and reference.
ドロップイン代替品: ADC121S101CIMFX — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: ADC121S101CIMFX （同一形状・フットプリント） — 相違点: Package, Sample Rate, Operating Temperature, Operating Temperature Range, Resolution.
クイック比較ツール — 並列比較する代替部品を選択:
ADC101S101CIMFX
✅ ドロップイン✓ 在庫あり
$1.25 / 個
データシートを見る →ADC081S101CIMFX
✅ ドロップイン📋 参考代替品（カタログ未掲載）
ADC121S021CISDX
✅ ドロップイン✓ 在庫あり
$1.85 / 個
データシートを見る →ADC121S051CIMFX
✅ ドロップイン✓ 在庫あり
$1.95 / 個
データシートを見る →MAX1112EUT+
✅ ドロップイン📋 参考代替品（カタログ未掲載）
ADCS7476ARMZ
✅ ドロップイン📋 参考代替品（カタログ未掲載）
ADC121S101CIMFX 最大定格＆電気的特性
| 分解能 | 12 bit |
| Number of Channels | 1 |
| Sample Rate | 0.5 to 1 MSPS |
| Architecture | SAR (Successive Approximation Register) |
| Input Type | Single-Ended |
| Supply Voltage (VA) | 2.7 V to 5.25 V |
| Supply Current (1 MSPS, 5 V) | 4.6 mW (typ) |
| Power-Down Current | 2.6 µW (typ, 5 V supply) |
| Digital Interface | SPI/QSPI/MICROWIRE-compatible serial |
| 入力電圧範囲 | 0 V to VA |
| 動作温度 | -40C to +125C |
| パッケージ | SOT-23-6 |
| 実装タイプ | Surface Mount |
| RoHS ステータス | Compliant |
| Lead-Free | Yes |
ADC121S101CIMFX ピン構成
| ピン 1 | VA — Analog supply voltage (2.7V to 5.25V); also used as reference |
| ピン 2 | GND — Ground |
| ピン 3 | IN — Analog input (0V to VA) |
| ピン 4 | SCLK — Serial clock input |
| ピン 5 | DOUT — Serial data output |
| ピン 6 | CS — Chip select (active low) |
主な用途
ADC121S101CIMFX の用途: 6 件s: Portable Battery-Powered Data Acquisition, Factory Automation Sensor Interface, Optical Module Monitoring, Motor Control Position Feedback, Low-Power Wireless Sensor Node, Medical Patient Monitoring.
Portable Battery-Powered Data Acquisition
The ADC121S101CIMFX fits portable, battery-powered data-acquisition front-ends because of its 4.6 mW active power at 1 MSPS with a 5 V supply and 2.6 µW power-down current. A microcontroller can keep the converter idle between bursts, then wake it via CS for sub-millisecond acquisition windows, dramatically extending battery life. Its 12-bit resolution is sufficient for sensor conditioning chains such as thermocouples, strain gauges, and gas-sensor outputs. The 2.7 V to 5.25 V supply range lets it operate directly from a Li-ion cell or a 3.3 V regulated rail without level shifting. Pin-compatible 10-bit and 8-bit family members let designers trade resolution for cost without altering the PCB.
おすすめ
Factory Automation Sensor Interface
In factory automation PLCs and distributed I/O modules, the ADC121S101CIMFX digitizes analog sensor outputs such as 4-20 mA loop converters, pressure transducers, and temperature bridges. The -40C to +125C operating range and RoHS-compliant SOT-23-6 package allow it to operate inside sealed industrial enclosures with minimal thermal derating. Its SPI-compatible serial interface shares a bus with multiple converters using independent CS lines, supporting dense multi-channel analog front-ends. The 0 V to VA input span simplifies signal-conditioning design because the analog rail itself acts as the reference. With 1 MSPS throughput, the ADC121S101CIMFX can sample multiple sensors in a fast round-robin sequence driven by the host microcontroller.
おすすめ
Optical Module Monitoring
Optical transceivers (SFP, QSFP, and tunable laser modules) use a low-power SAR ADC to monitor laser bias current, temperature, and received optical power for diagnostic telemetry. The ADC121S101CIMFX's tiny SOT-23-6 footprint fits inside the cramped module housing, while 1 MSPS throughput supports fast diagnostic sweeps without introducing latency on the host serial interface. Its 12-bit resolution is more than adequate for the typical 8-bit dynamic range of optical monitor signals, providing margin for calibration accuracy. The 2.6 µW power power-down current is critical because the module's housekeeping budget is shared with the laser driver and TEC controller. The SPI interface allows the host microcontroller to daisy-chain multiple ADCs across the module's I2C/SPI bus.
おすすめ
Motor Control Position Feedback
Brushless DC and stepper motor controllers use a SAR ADC to read resolver excitation or Hall-effect-derived analog rotor position, and the ADC121S101CIMFX is well-suited for this role. Its 1 MSPS throughput captures fast rotor transients at high RPM without aliasing, while the 12-bit resolution provides about 0.088 degrees of angular resolution after resolver decoding. The wide 2.7 V to 5.25 V supply range lets the same part operate from 3.3 V logic-level MCU rails or 5 V industrial backplanes. The SOT-23-6 footprint keeps the analog front-end compact, leaving board space for the gate driver and power stage. Pin-compatibility with the 8-bit ADC081S101 lets cost-sensitive variants drop the resolution for entry-level designs.
おすすめ
Low-Power Wireless Sensor Node
Wireless sensor nodes for IoT applications need an ADC with very low power-down current so that the sensor can sleep until a sample is needed. The ADC121S101CIMFX's 2.6 µW power-down current at 5 V is a strong fit, and the 4.6 mW active power is acceptable for short acquisition bursts. Its 12-bit resolution digitizes sensor outputs to the precision needed for environmental monitoring (temperature, humidity, light, gas). The SPI interface is compatible with most low-power wireless MCUs that already include an SPI peripheral for radio control. The 6-pin SOT-23 package is the smallest footprint available for this resolution class, freeing board space for the antenna and battery.
おすすめ
Medical Patient Monitoring
Patient monitoring devices such as pulse oximeters, blood-pressure cuffs, and bedside telemetry modules benefit from the ADC121S101CIMFX's 12-bit resolution and 1 MSPS throughput. The SOT-23-6 footprint keeps the analog front-end small, leaving room for the main MCU, display, and wireless link. The 2.7 V to 5.25 V supply range lets it operate from common medical-rail voltages. The SPI-compatible serial interface avoids I2C bus contention in multi-parameter monitors. The wide -40C to +125C operating range covers the full range of clinical and home-use environments. Pin-compatible 10-bit and 8-bit versions allow cost-down variants for over-the-counter health products.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: ADC121S101CIMFX — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | ADC101S101CIMFX | ADC081S101CIMFX | ADC121S021CISDX | ADC121S051CIMFX | MAX1112EUT+ | ADCS7476ARMZ |
|---|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Analog Devices | Analog Devices |
| Package | SOT-23-6 | SOT-23-6 | SOT-23-6 | SOT-23-6 | SOT-23-6 | SOT-23-6 | MSOP-8 |
| Resolution | 12 bit | 10 bit | 8 bit | 12 bit | 12 bit | 12 bit | 12 bit |
| Max Sample Rate | 1 MSPS | 1 MSPS | 1 MSPS | 200-500 ksps | 500 ksps | 50 ksps | 1 MSPS |
| Supply Voltage | 2.7 V to 5.25 V | 2.7 V to 5.25 V | 2.7 V to 5.25 V | 2.7 V to 5.25 V | 2.7 V to 5.25 V | 2.7 V to 5.25 V | 2.7 V to 5.25 V |
| Interface | SPI/QSPI/MICROWIRE | SPI/QSPI/MICROWIRE | SPI/QSPI/MICROWIRE | SPI/QSPI/MICROWIRE | SPI/QSPI/MICROWIRE | SPI/QSPI/MICROWIRE | SPI |
| Active Power (typ, 5 V) | 4.6 mW | 4.6 mW | 4.6 mW | 1.5 mW | 2.7 mW | 0.6 mW | 4.5 mW |
| Operating Temperature | -40C to +125C | -40C to +125C | -40C to +125C | -40C to +125C | -40C to +125C | -40C to +85C | -40C to +125C |
| Approx Unit Price (qty 1000) | $2.18 | $1.85 | $1.45 | $2.05 | $2.10 | $3.10 | $2.85 |
主な差別化要因
- Fastest 12-bit single-channel SAR in SOT-23-6 family （vs ADC121S051CIMFX)
- Wide supply range covers both 3.3 V and 5 V rails （vs MAX1112EUT+)
- Pin-compatible 8-bit/10-bit upgrade path （vs ADC081S101CIMFX / ADC101S101CIMFX)
設計ノート
Decouple the VA supply pin with a 0.1 µF X7R ceramic capacitor placed within 3 mm of the pin, with the ground-side trace shorting directly to the ground plane. For multi-channel designs sharing one reference, add a 10 µF bulk capacitor near the analog supply entry. Avoid sharing the VA trace with high-current digital loads, because the SAR conversion depends on a stable reference; noise on VA directly couples into the conversion result.
Route the analog input trace as a microstrip guarded by ground on both sides, keeping it short and far from the SCLK and DOUT traces. Place the ADC physically close to the analog source to minimize trace capacitance, which forms a low-pass filter with the source impedance and degrades effective bandwidth. Keep digital return currents separated from analog return currents; use a star-ground topology at the ADC's GND pin.
Do not operate VA below 2.7 V or above 5.25 V; the ADC121S101CIMFX is not a 3.3 V- or 5 V-only part, but excursions outside the datasheet range cause INL and DNL errors. Avoid leaving floating inputs, because the sample-and-hold can charge the input pin to unpredictable levels and degrade the next conversion. Ensure CS is asserted only when valid data is being clocked out, otherwise DOUT floats and the SPI peripheral may misinterpret bus activity.
When sharing the SPI bus with multiple ADCs, isolate each device's DOUT line with a small series resistor or buffer to prevent bus contention. Keep SCLK edges clean and below 20 MHz to avoid digital-feedthrough coupling into the analog input. If long SPI traces are unavoidable, terminate the bus at the far end with a small capacitor to dampen ringing and reduce radiated EMI.
コンプライアンス情報
Lead-free /NOPB variant available per TI product page. RoHS compliant. Not AEC-Q100 qualified - choose ADC121S101-Q1 for automotive. The ADC121S101 family was originally introduced by National Semiconductor and is now manufactured by Texas Instruments.