ADF4213BCPZ-RL7 - 3 GHz PLL Clock Generator | Analog Devices
部品番号: ADF4213BCPZ-RL7 ✓ 生産中ADF4213BCPZ-RL7 概要
A PLL frequency synthesizer is a clock-generation IC that locks an output phase and frequency to a reference signal through a phase detector, charge pump, loop filter, and voltage-controlled oscillator. The ADF4213 belongs to the frequency synthesizer hierarchy within clock and timing ICs, where it supports stable local oscillator generation, clock multiplication, and reference-frequency conversion in RF and microwave systems.
Key features include a maximum stated frequency of 3 GHz, CMOS input and clock output operation, a 3 V system supply, and a charge-pump supply rated up to 5.5 V. Separate charge-pump and system supplies give the circuit designer independent control over the oscillator-control voltage range. The device is identified as an industrial-temperature-grade component with a maximum operating temperature of 85 °C.
The ADF4213 architecture supports divider ratios up to 3:1 as identified for this family and uses programmable frequency synthesis for clock or local-oscillator generation. Designers must select the reference, feedback, and loop-filter values carefully because phase noise, reference spur levels, lock time, and tuning-range margin depend on the complete feedback network rather than on the IC alone.
Typical uses include RF and microwave transceiver local oscillators, frequency conversion stages, wireless communications equipment, instrumentation, and clock-generation subsystems. The 3 GHz capability makes the device relevant to upper-RF and microwave designs where a fixed integer divider alone cannot supply the required output frequency.
PCB implementation should preserve the integrity of the high-frequency reference and feedback paths, place decoupling capacitors close to the supply pins, and connect the exposed thermal pad according to the package land pattern. Confirm the reference amplitude, loop-filter values, operating divider settings, and thermal conditions in the manufacturer datasheet before release.
This page combines the exact device identification, package characteristics, cross-reference candidates, comparison data, and application-oriented engineering guidance needed to evaluate the ADF4213BCPZ-RL7 as a 3 GHz PLL clock generator.
ドロップイン代替品: ADF4213BCPZ-RL7 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: ADF4213BCPZ-RL7 (同一形状・フットプリント) — 相違点: Package, Device Type.
ADF4213BCP-REEL
✅ ドロップイン📋 参考代替品(カタログ未掲載)
ADF4213BCPZ-RL
✅ ドロップイン価格はお問い合わせください
データシートを見る →ADF4213BCPZ
✅ ドロップイン価格はお問い合わせください
データシートを見る →ADF4213BCPZ-RL7 仕様
| Device Type | Clock generator and PLL frequency synthesizer |
| Frequency Range | 0 MHz to 3 GHz |
| Maximum Frequency | 3 GHz |
| Input Signal Type | CMOS |
| Output Signal Type | Clock |
| PLL | Yes |
| Maximum Input-to-Output Ratio | 3:1 |
| Nominal Supply Voltage | 3 V |
| Maximum System Supply Voltage | 5.5 V |
| パッケージ | 20-LFCSP-EP |
| Terminal Count | 20 terminals |
| Terminal Pitch | 0.5 mm |
| Maximum Operating Temperature | 85 °C |
| Temperature Grade | Industrial |
| 実装タイプ | Surface mount |
| Package Shape | Square |
| Package Code | VQCCN |
ADF4213BCPZ-RL7 vqccn ピン配置ガイド
ADF4213BCPZ-RL7 (vqccn パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: ADF4213BCPZ-RL7.
詳細は データシート をご参照ください。
主な用途
ADF4213BCPZ-RL7 の用途: 6 件s: RF Transceiver Local Oscillator, Microwave Frequency Conversion, Communications Clock Generation, Instrumentation Signal Source, Industrial Frequency Conversion, Frequency Multiplication Module.
RF Transceiver Local Oscillator
The ADF4213BCPZ-RL7 fits a programmable local-oscillator block because its PLL frequency synthesizer supports frequencies up to 3 GHz and accepts a CMOS reference. Place it in the feedback loop between the reference divider, phase detector, charge pump, loop filter, and RF output divider, then select divider values that preserve the required tuning range. This arrangement allows a single low-frequency reference to generate the local-oscillator signal required by an RF signal chain. The principal trade-off is loop sensitivity: a narrow filter can improve phase noise but lengthen acquisition, while a wider filter can settle faster at the cost of greater integrated phase noise. Board-level verification must include reference spurs, lock-time margin, and conducted emissions across the intended operating band.
おすすめ
Microwave Frequency Conversion
The ADF4213BCPZ-RL7 can generate a programmable local-oscillator reference for microwave upconversion or downconversion stages. Its 3 GHz maximum operating frequency provides headroom for RF and microwave LO paths, while the separate charge-pump supply allows the oscillator-control range to be extended independently of the nominal 3 V system supply. The reference divider, feedback divider, and loop-filter network determine whether the requested channel spacing is reached without excessive phase noise or reference spurs. Keep the reference trace short and controlled, decouple the charge-pump supply close to the device, and test acquisition at the lowest and highest intended channel frequencies. Adequate exposed-pad heat spreading also helps maintain stable behavior in compact RF modules.
おすすめ
Communications Clock Generation
The ADF4213BCPZ-RL7 can derive a stable, programmable clock for RF and microwave communications equipment when a system reference must be multiplied or translated to a channel-specific frequency. The PLL provides a practical mechanism for maintaining frequency accuracy against the reference while supporting output rates as high as 3 GHz. In a communications design, use the reference and feedback dividers to establish the required multiplication ratio, then calculate the loop filter around the selected charge-pump settings. This approach avoids replacing multiple fixed-frequency oscillators with one programmable synthesizer. The engineering trade-off is spectral purity: reference multiplication and loop bandwidth determine phase noise and spur levels, so adjacent-channel requirements should be measured with the intended reference oscillator and filtering network.
おすすめ
Instrumentation Signal Source
The ADF4213BCPZ-RL7 can serve as the programmable synthesis element in a laboratory or industrial signal source when the required output extends to RF frequencies. Its PLL architecture supports channel selection through programmable frequency settings rather than mechanically tuned resonators, improving repeatability and automation potential. The reference should have low phase noise and good frequency stability because the synthesized output inherits much of the reference quality and loop-filter trade-offs. Separate decoupling for the nominal 3 V system rail and the charge-pump supply reduces coupling between sensitive circuitry. During development, capture phase noise, spur levels, settling time, and output power at several frequencies so that the loop design remains valid across the complete operating range.
おすすめ
Industrial Frequency Conversion
The ADF4213BCPZ-RL7 is suitable for industrial RF equipment that requires a programmable local oscillator for sensing, excitation, or frequency-conversion functions. Its stated industrial temperature grade and maximum operating temperature of 85 °C support controlled industrial environments, while the 20-LFCSP-EP package supports compact surface-mount construction. The PLL can derive the required excitation frequency from a shared reference, simplifying calibration and allowing software-controlled channel selection. Designers should assess reference availability, lock margin, phase noise, and temperature drift across the operating range. Thermal management, reference isolation, and filtering of the control voltage are as important as the nominal frequency setting because they directly influence repeatability and spectral performance.
おすすめ
Frequency Multiplication Module
The ADF4213BCPZ-RL7 can multiply a CMOS reference into a higher-frequency clock for modular RF and microwave subsystems. Its maximum operating frequency of 3 GHz allows the feedback divider to synthesize outputs above the reference frequency, while the 3 V system supply and separate charge-pump supply support separate signal-path and tuning functions. In a compact module, place the bypass capacitors at the supply pins, preserve a continuous ground return beneath the exposed pad, and use a short reference path to reduce pickup and phase-noise conversion. Validate both the integer division ratios and the achievable loop bandwidth before production. If a module requires exceptionally low phase noise, a narrow loop or a cleaner reference may be necessary even though the PLL itself can generate the required frequency.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: ADF4213BCPZ-RL7 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | ADF4213BCP-REEL | ADF4213BCPZ-RL | ADF4213BCPZ |
|---|---|---|---|---|
| Package | 20-LFCSP-EP | 20-LFCSP-EP | 20-LFCSP-EP | 20-LFCSP-EP |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Device Type | Clock generator and PLL frequency synthesizer | Clock generator and PLL frequency synthesizer | Clock generator and PLL frequency synthesizer | Clock generator and PLL frequency synthesizer |
| Frequency Range | 0 MHz to 3 GHz | 0 MHz to 3 GHz | 0 MHz to 3 GHz | 0 MHz to 3 GHz |
| Maximum Frequency | 3 GHz | 3 GHz | 3 GHz | 3 GHz |
| Nominal Supply Voltage | 3 V | 3 V | 3 V | 3 V |
| Maximum System Supply Voltage | 5.5 V | 5.5 V | 5.5 V | 5.5 V |
| Input Signal Type | CMOS | CMOS | CMOS | CMOS |
| Maximum Input-to-Output Ratio | 3:1 | 3:1 | 3:1 | 3:1 |
| Maximum Operating Temperature | 85 °C | 85 °C | 85 °C | 85 °C |
| Temperature Grade | Industrial | Industrial | Industrial | Industrial |
| Terminal Count and Pitch | 20 terminals at 0.5 mm pitch | 20 terminals at 0.5 mm pitch | 20 terminals at 0.5 mm pitch | 20 terminals at 0.5 mm pitch |
主な差別化要因
- Full 3 GHz operating range (vs ADF4213BCP-REEL)
- Identical package and terminal arrangement (vs ADF4213BCPZ-RL)
- Independent charge-pump supply capability (vs ADF4213BCPZ)
設計ノート
Use the manufacturer land pattern for the 20-LFCSP-EP package and connect the exposed pad to the appropriate ground plane. Place input, output, and bypass components close to their associated pins, with short return paths for the reference and feedback signals. Because the exposed pad is both a thermal and electrical feature, verify paste coverage, solder fill, and reflow profile during assembly qualification.
Keep the reference and feedback routes compact, continuous, and away from switching nodes and high-current return paths. A phase-noise-sensitive clock synthesizer can convert reference noise, supply ripple, and ground bounce into output phase noise. Use a low-noise reference, adequate reference decoupling, and a controlled ground return, then measure phase noise and reference spurs at the lowest and highest operating frequencies.
Do not assume that every part sharing the ADF4213 base number is electrically interchangeable. Confirm the pin-description table, divider limits, charge-pump behavior, register map, programming procedure, exposed-pad connection, and ordering suffix before approving a substitute. After any replacement, repeat lock-time, spur, phase-noise, and temperature testing because package compatibility alone does not guarantee system-level equivalence.
Decouple the nominal 3 V system supply and the separate charge-pump supply independently, following the manufacturer recommendations for capacitance, placement, and layout. Avoid routing charge-pump current through the reference or feedback return. Validate supply ripple, startup behavior, and lock stability with the final regulator and load arrangement because both reference noise and supply coupling can affect the synthesized output.
コンプライアンス情報
The product is identified as an industrial-temperature-grade PLL, but no specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was identified in the referenced product records. AEC-Q100 is marked not applicable because this industrial clock IC is not presented as an automotive-qualified device.