Analog Devices

ADF4213BCPZ-RL7 - 3 GHz PLL Clock Generator | Analog Devices

料号: ADF4213BCPZ-RL7 ✓ 量产中
3 V Vdss 20-LFCSP-EP Package 0 MHz to 3 GHz Speed
最小起订量: 1 |

ADF4213BCPZ-RL7 概述

Analog Devices ADF4213BCPZ-RL7 is a clock-generator and phase-locked-loop frequency synthesizer with an input and output frequency range extending to 3 GHz, a 3 V nominal supply, and a 20-terminal LFCSP with exposed-pad package. The device supports 550 MHz, 1.2 GHz, 1.0 GHz, 2.0 GHz, 2.7 GHz, and 3 GHz operating-rate options and includes a separate charge-pump supply for an extended tuning-voltage range.

A PLL frequency synthesizer is a clock-generation IC that locks an output phase and frequency to a reference signal through a phase detector, charge pump, loop filter, and voltage-controlled oscillator. The ADF4213 belongs to the frequency synthesizer hierarchy within clock and timing ICs, where it supports stable local oscillator generation, clock multiplication, and reference-frequency conversion in RF and microwave systems.

Key features include a maximum stated frequency of 3 GHz, CMOS input and clock output operation, a 3 V system supply, and a charge-pump supply rated up to 5.5 V. Separate charge-pump and system supplies give the circuit designer independent control over the oscillator-control voltage range. The device is identified as an industrial-temperature-grade component with a maximum operating temperature of 85 °C.

The ADF4213 architecture supports divider ratios up to 3:1 as identified for this family and uses programmable frequency synthesis for clock or local-oscillator generation. Designers must select the reference, feedback, and loop-filter values carefully because phase noise, reference spur levels, lock time, and tuning-range margin depend on the complete feedback network rather than on the IC alone.

Typical uses include RF and microwave transceiver local oscillators, frequency conversion stages, wireless communications equipment, instrumentation, and clock-generation subsystems. The 3 GHz capability makes the device relevant to upper-RF and microwave designs where a fixed integer divider alone cannot supply the required output frequency.

PCB implementation should preserve the integrity of the high-frequency reference and feedback paths, place decoupling capacitors close to the supply pins, and connect the exposed thermal pad according to the package land pattern. Confirm the reference amplitude, loop-filter values, operating divider settings, and thermal conditions in the manufacturer datasheet before release.

This page combines the exact device identification, package characteristics, cross-reference candidates, comparison data, and application-oriented engineering guidance needed to evaluate the ADF4213BCPZ-RL7 as a 3 GHz PLL clock generator.

直接替换替代料: ADF4213BCPZ-RL7 ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: ADF4213BCPZ-RL7 (相同外形与封装尺寸) ——差异在于 Package, Device Type.

Analog Devices
Package: 20-pin VFQFN exposed-pad package
Device Type: Clock/Frequency Synthesizer (RF/IF)
对比 ADF4213BCPZ-RL7 →
Analog Devices
Package: 20-pin VQFN exposed-pad LFCSP
对比 ADF4213BCPZ-RL7 →

ADF4213BCP-REEL

✅ 直接替换
📦 20-LFCSP-EP
Same documented terminals, package, and principal performance; ordering designation changes reel packing, with 0 MHz to 3 GHz frequency range unchanged.

📋 参考替代料(不在目录中)

ADF4213BCPZ-RL

✅ 直接替换
Analog Devices
📦 20-LFCSP-EP
RF/IF PLL frequency synthesizer · 3 GHz · 2.7 V to 5.5 V · Supported · 8/9, 16/17, 32/33, 64/65 · 8/9, 16/17, 32/33, 64/65 · 3-wire · Analog and digital

联系询价

查看数据手册 →

ADF4213BCPZ

✅ 直接替换
Analog Devices
📦 20-LFCSP-EP
Clock/Frequency Synthesizer (RF/IF) · Yes · CMOS · Clock · 3 GHz · 0 MHz · 2.7 V to 5.5 V · 1

联系询价

查看数据手册 →

ADF4213BCPZ-RL7 规格参数

Device Type Clock generator and PLL frequency synthesizer
Frequency Range 0 MHz to 3 GHz
Maximum Frequency 3 GHz
Input Signal Type CMOS
Output Signal Type Clock
PLL Yes
Maximum Input-to-Output Ratio 3:1
Nominal Supply Voltage 3 V
Maximum System Supply Voltage 5.5 V
封装 20-LFCSP-EP
Terminal Count 20 terminals
Terminal Pitch 0.5 mm
Maximum Operating Temperature 85 °C
Temperature Grade Industrial
安装类型 Surface mount
Package Shape Square
Package Code VQCCN

ADF4213BCPZ-RL7 vqccn 引脚配置指南

ADF4213BCPZ-RL7(vqccn 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。

ADF4213BCPZ-RL7 的 vqccn 封装引脚图

暂无详细引脚数据: ADF4213BCPZ-RL7.

请参阅 数据手册 以查看完整引脚配置。

典型应用

ADF4213BCPZ-RL7 适用于 6 应用s: RF Transceiver Local Oscillator, Microwave Frequency Conversion, Communications Clock Generation, Instrumentation Signal Source, Industrial Frequency Conversion, Frequency Multiplication Module.

🌐

RF Transceiver Local Oscillator

The ADF4213BCPZ-RL7 fits a programmable local-oscillator block because its PLL frequency synthesizer supports frequencies up to 3 GHz and accepts a CMOS reference. Place it in the feedback loop between the reference divider, phase detector, charge pump, loop filter, and RF output divider, then select divider values that preserve the required tuning range. This arrangement allows a single low-frequency reference to generate the local-oscillator signal required by an RF signal chain. The principal trade-off is loop sensitivity: a narrow filter can improve phase noise but lengthen acquisition, while a wider filter can settle faster at the cost of greater integrated phase noise. Board-level verification must include reference spurs, lock-time margin, and conducted emissions across the intended operating band.

🌐

Microwave Frequency Conversion

The ADF4213BCPZ-RL7 can generate a programmable local-oscillator reference for microwave upconversion or downconversion stages. Its 3 GHz maximum operating frequency provides headroom for RF and microwave LO paths, while the separate charge-pump supply allows the oscillator-control range to be extended independently of the nominal 3 V system supply. The reference divider, feedback divider, and loop-filter network determine whether the requested channel spacing is reached without excessive phase noise or reference spurs. Keep the reference trace short and controlled, decouple the charge-pump supply close to the device, and test acquisition at the lowest and highest intended channel frequencies. Adequate exposed-pad heat spreading also helps maintain stable behavior in compact RF modules.

📡

Communications Clock Generation

The ADF4213BCPZ-RL7 can derive a stable, programmable clock for RF and microwave communications equipment when a system reference must be multiplied or translated to a channel-specific frequency. The PLL provides a practical mechanism for maintaining frequency accuracy against the reference while supporting output rates as high as 3 GHz. In a communications design, use the reference and feedback dividers to establish the required multiplication ratio, then calculate the loop filter around the selected charge-pump settings. This approach avoids replacing multiple fixed-frequency oscillators with one programmable synthesizer. The engineering trade-off is spectral purity: reference multiplication and loop bandwidth determine phase noise and spur levels, so adjacent-channel requirements should be measured with the intended reference oscillator and filtering network.

🖥️

Instrumentation Signal Source

The ADF4213BCPZ-RL7 can serve as the programmable synthesis element in a laboratory or industrial signal source when the required output extends to RF frequencies. Its PLL architecture supports channel selection through programmable frequency settings rather than mechanically tuned resonators, improving repeatability and automation potential. The reference should have low phase noise and good frequency stability because the synthesized output inherits much of the reference quality and loop-filter trade-offs. Separate decoupling for the nominal 3 V system rail and the charge-pump supply reduces coupling between sensitive circuitry. During development, capture phase noise, spur levels, settling time, and output power at several frequencies so that the loop design remains valid across the complete operating range.

🏭

Industrial Frequency Conversion

The ADF4213BCPZ-RL7 is suitable for industrial RF equipment that requires a programmable local oscillator for sensing, excitation, or frequency-conversion functions. Its stated industrial temperature grade and maximum operating temperature of 85 °C support controlled industrial environments, while the 20-LFCSP-EP package supports compact surface-mount construction. The PLL can derive the required excitation frequency from a shared reference, simplifying calibration and allowing software-controlled channel selection. Designers should assess reference availability, lock margin, phase noise, and temperature drift across the operating range. Thermal management, reference isolation, and filtering of the control voltage are as important as the nominal frequency setting because they directly influence repeatability and spectral performance.

⚡

Frequency Multiplication Module

The ADF4213BCPZ-RL7 can multiply a CMOS reference into a higher-frequency clock for modular RF and microwave subsystems. Its maximum operating frequency of 3 GHz allows the feedback divider to synthesize outputs above the reference frequency, while the 3 V system supply and separate charge-pump supply support separate signal-path and tuning functions. In a compact module, place the bypass capacitors at the supply pins, preserve a continuous ground return beneath the exposed pad, and use a short reference path to reduce pickup and phase-noise conversion. Validate both the integer division ratios and the achievable loop bandwidth before production. If a module requires exceptionally low phase noise, a narrow loop or a cleaner reference may be necessary even though the PLL itself can generate the required frequency.

What is the ADF4213BCPZ-RL7?
The ADF4213BCPZ-RL7 is an Analog Devices clock generator and PLL frequency synthesizer operating from 0 MHz to 3 GHz. According to the manufacturer datasheet, the device uses a PLL architecture with separate system and charge-pump supplies, CMOS input signaling, and clock output circuitry in a 20-LFCSP-EP package.
What is the maximum operating frequency of ADF4213BCPZ-RL7?
The ADF4213BCPZ-RL7 supports operation up to 3 GHz. The manufacturer datasheet identifies related rate configurations at 550 MHz, 1.2 GHz, 1.0 GHz, 2.0 GHz, 2.7 GHz, and 3 GHz, indicating that device selection and internal divider configuration determine the usable operating range.
What supply voltage does the ADF4213BCPZ-RL7 use?
The ADF4213BCPZ-RL7 operates from a nominal 3 V supply, with a stated maximum system supply of 5.5 V. According to the manufacturer datasheet, the separate charge-pump supply can also reach 5.5 V, allowing a wider oscillator tuning-voltage range than the system supply alone would provide.
What package is used by the ADF4213BCPZ-RL7?
The ADF4213BCPZ-RL7 is supplied in a 20-LFCSP-EP surface-mount package with a 0.5 mm terminal pitch and an exposed pad. According to the manufacturer datasheet and product records, the package uses the VQCCN code and is intended for reflow soldering rather than through-hole assembly.
Where can I download the ADF4213BCPZ-RL7 datasheet PDF?
The ADF4213BCPZ-RL7 datasheet PDF is available from Analog Devices through the official ADF4213 data-sheet link on this page. The document contains the pin-description table, recommended operating conditions, application circuit, register information, and package dimensions needed to verify the complete design.
Where can I find the ADF4213BCPZ-RL7 pinout?
The ADF4213BCPZ-RL7 pinout is defined by the pin-description table in the Analog Devices ADF4213 datasheet. The component uses a 20-LFCSP-EP package with an exposed pad, so the PCB land pattern must include both the 20 numbered terminals and the exposed-pad connection described by the manufacturer.
Is ADF4213BCPZ-RL7 suitable for RF local-oscillator generation?
Yes, the ADF4213BCPZ-RL7 is suitable for RF local-oscillator generation when the target frequency, reference conditions, divider ratios, and loop-filter design fall within the device limits. Its PLL architecture and 3 GHz maximum frequency suit frequency-generation blocks, while phase noise and spur performance must be evaluated from the complete reference and feedback design.
How do I design the loop filter for the ADF4213BCPZ-RL7?
Start with the reference frequency, target output frequency, required lock time, phase-noise target, and charge-pump current listed in the manufacturer datasheet. Use those values to determine loop bandwidth and component values. A wider loop generally improves lock time but increases phase noise, so the final filter should be verified against both settling and spectral requirements.
What is the difference between ADF4213BCPZ-RL7 and ADF4213BCPZ-RL?
The ADF4213BCPZ-RL7 and ADF4213BCPZ-RL are presented as completely replaceable parts with consistent terminals, packages, and principal performance characteristics. Their package-related ordering designations differ, but engineers should confirm the exact tape-and-reel suffix, marking, temperature grade, and exposed-pad requirements before treating either ordering code as a substitution.
What is the best drop-in replacement for ADF4213BCPZ-RL7?
ADF4213BCP-REEL is the closest documented same-package replacement candidate for the ADF4213BCPZ-RL7. The cross-reference describes consistent terminals, package, and principal performance, but no broader set of distinct drop-in devices could be established without matching every pin, divider, register, and electrical limit. Board revision is required before final substitution approval.
Can ADF4213BCP-REEL replace ADF4213BCPZ-RL7?
ADF4213BCP-REEL can be treated as a candidate replacement for the ADF4213BCPZ-RL7 because cross-reference records identify consistent terminals, package, and principal functional characteristics. The device is the same Analog Devices family, but production documentation and the complete pin descriptions should still be compared before approving the change for a released PCB.
When should I choose ADF4213BCPZ-RL7 instead of another PLL?
Choose the ADF4213BCPZ-RL7 when the design needs a programmable PLL clock generator with operation up to 3 GHz, CMOS reference interfacing, separate system and charge-pump supplies, and a 20-LFCSP-EP footprint. Choose a different PLL only when its frequency range, reference rate, divider structure, register interface, tuning range, or package offers a closer match to those requirements.
ADF4213BCPZ-RL7 versus ADF4213BCPZ-RL: which ordering code should I fit?
ADF4213BCPZ-RL7 and ADF4213BCPZ-RL are documented as electrically and pin compatible, so selection should follow the exact suffix approved for your bill of materials and production packaging. Verify the manufacturer ordering guide for reel orientation, tape quantity, temperature grade, and marking rather than treating an identical core device number as proof that every production detail is interchangeable.
Where can I buy ADF4213BCPZ-RL7 and check its lead time?
Use the Request a Quote form on this page to request the current unit price, stock position, minimum order quantity, and lead time for the ADF4213BCPZ-RL7. A quote request preserves the exact ordering code ADF4213BCPZ-RL7 and avoids ambiguity with the base ADF4213BCPZ device or other reel and temperature-grade suffixes.
What are the key specifications of ADF4213BCPZ-RL7 that engineers should know?
The ADF4213BCPZ-RL7 combines a 0 MHz to 3 GHz operating range with PLL frequency synthesis, CMOS clock input and output, a nominal 3 V system supply, and a maximum system supply of 5.5 V. It is packaged as a 20-LFCSP-EP surface-mount device with 20 terminals, 0.5 mm pitch, an exposed pad, industrial temperature grade, and a maximum operating temperature of 85 °C.
Is there a cross-brand drop-in equivalent for the ADF4213BCPZ-RL7?
No verified cross-brand drop-in equivalent is established for the ADF4213BCPZ-RL7. RF PLL replacements are rarely interchangeable solely because they share a package, since reference pins, dividers, charge-pump settings, register maps, and programming interfaces can differ. The documented candidates are from Analog Devices, so board-level and firmware validation remain necessary before any substitution.

工程参考数据: ADF4213BCPZ-RL7 ——对比、设计指导和合规信息。

选型指南

Choose the ADF4213BCPZ-RL7 when the design requires a 3 GHz-class PLL clock generator with CMOS reference input, separate system and charge-pump supplies, and a 20-LFCSP-EP footprint. ADF4213BCP-REEL is the closest documented alternative when its exact ordering, packing, and marking requirements satisfy production. ADF4213BCPZ-RL is another closely related ordering designation, while the base ADF4213BCPZ may fit designs that do not require the -RL7 production suffix. These options come from the same Analog Devices family and have the same documented terminal and package characteristics. Before selecting any of them, compare the complete pin descriptions, divider limits, register behavior, reference requirements, and ordering information. For designs requiring a fractional-N synthesizer, different reference architecture, lower phase noise, or another package, evaluate a different PLL rather than assuming that shared package dimensions guarantee system compatibility.

与替代料对比

参数 本产品 ADF4213BCP-REEL ADF4213BCPZ-RL ADF4213BCPZ
Package 20-LFCSP-EP 20-LFCSP-EP 20-LFCSP-EP 20-LFCSP-EP
Brand Analog Devices Analog Devices Analog Devices Analog Devices
Device Type Clock generator and PLL frequency synthesizer Clock generator and PLL frequency synthesizer Clock generator and PLL frequency synthesizer Clock generator and PLL frequency synthesizer
Frequency Range 0 MHz to 3 GHz 0 MHz to 3 GHz 0 MHz to 3 GHz 0 MHz to 3 GHz
Maximum Frequency 3 GHz 3 GHz 3 GHz 3 GHz
Nominal Supply Voltage 3 V 3 V 3 V 3 V
Maximum System Supply Voltage 5.5 V 5.5 V 5.5 V 5.5 V
Input Signal Type CMOS CMOS CMOS CMOS
Maximum Input-to-Output Ratio 3:1 3:1 3:1 3:1
Maximum Operating Temperature 85 °C 85 °C 85 °C 85 °C
Temperature Grade Industrial Industrial Industrial Industrial
Terminal Count and Pitch 20 terminals at 0.5 mm pitch 20 terminals at 0.5 mm pitch 20 terminals at 0.5 mm pitch 20 terminals at 0.5 mm pitch

关键差异点

  • Full 3 GHz operating range (对比 ADF4213BCP-REEL)
  • Identical package and terminal arrangement (对比 ADF4213BCPZ-RL)
  • Independent charge-pump supply capability (对比 ADF4213BCPZ)

设计说明

Use the manufacturer land pattern for the 20-LFCSP-EP package and connect the exposed pad to the appropriate ground plane. Place input, output, and bypass components close to their associated pins, with short return paths for the reference and feedback signals. Because the exposed pad is both a thermal and electrical feature, verify paste coverage, solder fill, and reflow profile during assembly qualification.

Keep the reference and feedback routes compact, continuous, and away from switching nodes and high-current return paths. A phase-noise-sensitive clock synthesizer can convert reference noise, supply ripple, and ground bounce into output phase noise. Use a low-noise reference, adequate reference decoupling, and a controlled ground return, then measure phase noise and reference spurs at the lowest and highest operating frequencies.

Do not assume that every part sharing the ADF4213 base number is electrically interchangeable. Confirm the pin-description table, divider limits, charge-pump behavior, register map, programming procedure, exposed-pad connection, and ordering suffix before approving a substitute. After any replacement, repeat lock-time, spur, phase-noise, and temperature testing because package compatibility alone does not guarantee system-level equivalence.

Decouple the nominal 3 V system supply and the separate charge-pump supply independently, following the manufacturer recommendations for capacitance, placement, and layout. Avoid routing charge-pump current through the reference or feedback return. Validate supply ripple, startup behavior, and lock stability with the final regulator and load arrangement because both reference noise and supply coupling can affect the synthesized output.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

The product is identified as an industrial-temperature-grade PLL, but no specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was identified in the referenced product records. AEC-Q100 is marked not applicable because this industrial clock IC is not presented as an automotive-qualified device.

相关搜索

ADF4213BCPZ-RL7 datasheet ADF4213BCPZ-RL7 pinout ADF4213BCPZ-RL7 datasheet pdf ADF4213BCPZ-RL7 specifications ADF4213BCPZ-RL7 equivalent ADF4213BCPZ-RL7 replacement ADF4213BCPZ-RL7 cross reference ADF4213BCPZ-RL7 3 GHz PLL ADF4213BCPZ-RL7 20-LFCSP-EP ADF4213BCPZ-RL7 RF local oscillator ADF4213BCPZ-RL7 price ADF4213BCPZ-RL7 stock Analog Devices ADF4213BCPZ-RL7 ADF4213BCPZ-RL7 loop filter ADF4213BCPZ-RL7 vs ADF4213BCPZ-RL

相关元器件 & 术语

Analog Devices ADF4213BCPZ-RL7 ADF4213BCP-REEL ADF4213BCPZ-RL ADF4213BCPZ ADF4154BCP-REEL ADF4208BRU-REEL PLL frequency synthesizer clock generator phase-locked loop frequency synthesizer clock and timing IC phase detector charge pump loop filter voltage-controlled oscillator CMOS reference local oscillator frequency conversion RF and microwave 20-LFCSP-EP VQCCN package code surface-mount package 3 GHz maximum frequency 0.5 mm terminal pitch
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情