Analog Devices

ADM213EARUZ - 4/5 RS-232 Transceiver | Analog Devices

部品番号: ADM213EARUZ ✓ 生産中
+5 V Vdss 28-pin TSSOP Package
MOQ: 1 |

ADM213EARUZ 概要

The Analog Devices ADM213EARUZ is a +5 V RS-232 transceiver with four drivers, five receivers, full-duplex operation, and a 28-pin TSSOP package. The manufacturer identifies a 200 kbps operating rate, 0.1 µF charge-pump capacitors, shutdown and enable pins, and two receivers that remain active during shutdown. These characteristics place the device within the RS-232 interface IC hierarchy, where a transceiver converts between TTL-compatible logic levels and differential, bipolar RS-232 signal levels.

An RS-232 transceiver is an interface IC that combines line drivers and line receivers on one die. The ADM213EARUZ is designed for EIA-232-E and V.28 links where a +12 V supply is unavailable. Its four-driver and five-receiver arrangement supports multi-channel equipment links, while the full-duplex architecture permits command responses and status data to travel concurrently over separate signal pairs.

Key features include operation from a single +5 V supply, a 200 kbps data rate, and integrated charge-pump support using 0.1 µF capacitors. The shutdown and enable controls support power management, and two receiver outputs remain active in shutdown mode for monitoring selected lines. The 28-pin TSSOP package also provides a compact surface-mount footprint for industrial control, instrumentation, and embedded serial-port equipment.

Technically, the ADM213EARUZ belongs to Analog Devices' ADM2xx family of robust RS-232 and V.28 interface devices. The manufacturer states that the family is intended for electrical environments where 12 V is unavailable and notes compliance with the EU EMC directive identified as 89/336/EEC. Its integrated drivers and receivers reduce the number of external components required for a multi-channel interface while centralizing polarity and signal-level conversion.

Typical uses include industrial control panels, test and measurement instruments, barcode and serial equipment, embedded controllers, and data-acquisition systems. A four-driver link can control four downstream channels, while five receivers can monitor remote equipment status, fault lines, and command acknowledgements. The 200 kbps rate is appropriate for legacy serial-console, point-to-point, and industrial instrumentation links that do not require modern high-speed differential buses.

Place the required charge-pump capacitors close to their associated device pins and maintain symmetric signal routing where possible. Confirm logic-level compatibility, connector pin assignment, and cable length before deployment, because the +5 V interface describes the transceiver supply rather than the RS-232 driver voltage amplitude. The shutdown function should not be used as a substitute for galvanic isolation or surge protection.

This page combines the manufacturer's functional description with practical interface-selection guidance, verified source links, a pin-compatible tape-and-reel option, and engineering notes covering power, layout, and signal integrity.

ドロップイン代替品: ADM213EARUZ — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

このシリーズのバリエーション

同一シリーズでドロップイン互換のモデル: ADM213EARUZ (同一形状・フットプリント) — 相違点: Package.

Analog Devices
Package: 28-pin SOIC
比較対象 ADM213EARUZ →

ADM213EARUZ-REEL7

✅ ドロップイン
📦 28-pin TSSOP
Identical 4/5 RS-232 transceiver configuration and 28-pin TSSOP footprint; ordering code changes reel packaging only, with no change to the 200 kbps operating class stated for the ADM213 family.

📋 参考代替品(カタログ未掲載)

ADM213EARUZ 仕様

Product Type RS-232 transceiver
電源電圧 +5 V
データレート 200 kbps
Driver Count 4 drivers
Receiver Count 5 receivers
Duplex Mode Full duplex
Charge-Pump Capacitor 0.1 µF
パッケージ 28-pin TSSOP
実装タイプ Surface mount
Shutdown Control Yes
Enable Control Yes
Receivers Active in Shutdown 2 receivers
Communication Standard EIA-232-E and V.28
EMC Directive EU EMC directive 89/336/EEC
RoHS ステータス RoHS3 compliant
REACH Status REACH unaffected
Moisture Sensitivity Level MSL 1 (unlimited)

ADM213EARUZ 28-pin tssop ピン配置ガイド

ADM213EARUZ (28-pin tssop パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。

ADM213EARUZ の 28-pin tssop パッケージピン配置図

詳細なピン配置データはありません: ADM213EARUZ.

詳細は データシート をご参照ください。

主な用途

ADM213EARUZ の用途: 6 件s: Industrial Control Panel Interface, Test and Measurement Instrument, Point-to-Point Serial Console, Data Acquisition Equipment, Embedded Equipment Controller, Serial Equipment Networking.

🏭

Industrial Control Panel Interface

The ADM213EARUZ suits an industrial control panel that must communicate with several remote actuators while monitoring additional feedback or fault signals. Its four drivers can support four command or control channels, while five receivers provide separate inputs for acknowledgements, interlocks, and status reporting. The full-duplex configuration lets the controller transmit and receive concurrently over independent pairs. Operating from a single +5 V supply simplifies the controller power architecture, while the 200 kbps rate is appropriate for conventional RS-232 equipment links. Designers should still include connector-level surge protection and verify the panel's ground strategy before connecting long external cables.

🔧

Test and Measurement Instrument

The ADM213EARUZ can simplify a laboratory instrument that must issue commands and retrieve data through multiple RS-232 ports. Four driver channels support separate control destinations, while the fifth receiver provides an additional monitoring path beyond the four-command architecture. At a 200 kbps data rate, the interface is well matched to legacy serial-port instruments and bench controllers that exchange moderate volumes of configuration or measurement data. Place the charge-pump capacitors close to the device and keep the ground reference consistent across the instrument, connector, and attached equipment. External protection remains appropriate when users connect the instrument to unknown or externally powered systems.

🖥️

Point-to-Point Serial Console

The ADM213EARUZ can be used for an embedded controller or service-console interface that includes receive-monitor lines in addition to its main command path. Although a simple console may need only one transmitter and one receiver, the ADM213EARUZ consolidates four drivers, five receivers, shutdown control, and enable control into one +5 V IC. The two receivers that remain active during shutdown allow a system to monitor selected remote conditions while reducing power to the rest of the interface. The 200 kbps operating rate supports conventional console traffic, but the board design must preserve the manufacturer's pin assignments and charge-pump capacitor placement.

📊

Data Acquisition Equipment

The ADM213EARUZ fits data-acquisition equipment that exchanges commands and status information with several external sensors or instrument modules. The four-driver arrangement supports multiple outbound control paths, and the five-receiver arrangement permits more incoming measurements than a basic two-wire console interface. Full-duplex operation avoids forcing traffic onto a shared serial direction, while the 200 kbps rate is appropriate for supervisory and status traffic rather than continuous high-volume streaming. In a laboratory or factory installation, use the transceiver with a defined signal-ground reference and add external protection at exposed connectors so transient energy does not bypass the device's intended operating environment.

🧩

Embedded Equipment Controller

The ADM213EARUZ is useful in embedded equipment that retains legacy RS-232 ports while adding controlled power management. Its +5 V operation fits many controller boards, and the shutdown and enable inputs allow the interface to be managed during different system states. Two receivers can continue monitoring important lines while the main transceiver functions are shut down, supporting fault detection or an always-present status indication. This behavior can reduce system power without abandoning communication monitoring. Firmware and hardware should define the enable and shutdown states carefully so partially powered interfaces cannot contend with an external RS-232 driver on the same bus.

🌐

Serial Equipment Networking

The ADM213EARUZ can bridge a controller to a group of legacy RS-232 devices through dedicated driver and receiver channels. Four command outputs can reach separate instruments, and the additional receiver channels can collect independent acknowledgements or interlocks without forcing shared multiplexing. The 200 kbps rate accommodates supervisory commands, status updates, and configuration transfers typical of industrial networks. Because RS-232 is point-to-point rather than a multi-drop bus, keep each driver connected to its intended receiver and avoid connecting multiple outputs together. Maintain consistent reference grounding and include connector protection when equipment is connected or disconnected during field service.

おすすめ製品の概要

ADM213EARUZ-REEL7 Same electrical device supplied on a reel 使用用途: Industrial Control Panel Interface, Test and Measurement Instrument, Point-to-Point Serial Console, Data Acquisition Equipment, Embedded Equipment Controller, Serial Equipment Networking MAX3221EIDBR Texas Instruments 使用用途: Industrial Control Panel Interface, Test and Measurement Instrument, Point-to-Point Serial Console, Data Acquisition Equipment, Embedded Equipment Controller, Serial Equipment Networking
What is the ADM213EARUZ and what does it do?
The ADM213EARUZ is a +5 V RS-232 transceiver containing four line drivers and five line receivers in a 28-pin TSSOP package. It converts between TTL-compatible logic signals and RS-232 levels while supporting full-duplex communication. According to the Analog Devices ADM213 product information, the ADM2xx family is intended for EIA-232-E and V.28 interfaces, particularly where a 12 V supply is unavailable.
What are the key specifications of ADM213EARUZ that engineers should know?
The ADM213EARUZ combines four drivers, five receivers, full-duplex operation, and a 200 kbps data rate in a 28-pin TSSOP package. It operates from a single +5 V supply and uses 0.1 µF charge-pump capacitors. Analog Devices also identifies shutdown and enable pins, plus two receiver outputs that remain active during shutdown, allowing selected status lines to be monitored while the main interface is powered down.
What is the operating voltage of ADM213EARUZ?
The ADM213EARUZ operates from a single +5 V supply. That rating applies to the transceiver's logic and internal charge-pump supply, not to the nominal voltage measured at an RS-232 driver output. The Analog Devices ADM213E product page describes the device as a +5 V CMOS RS-232 transceiver for EIA-232-E and V.28 communication interfaces, with integrated charge-pump operation using 0.1 µF capacitors.
How many RS-232 drivers and receivers does ADM213EARUZ have?
The ADM213EARUZ contains four RS-232 drivers and five RS-232 receivers. It also supports full-duplex operation, so independent transmit and receive paths can operate concurrently. According to the Analog Devices ADM213 product information, two receivers remain active in shutdown mode, which provides a practical way to monitor two incoming status or fault signals while reducing the power consumed by the remaining interface functions.
What data rate does ADM213EARUZ support?
The Analog Devices ADM213 product page identifies a 200 kbps data rate for the ADM213 family associated with ADM213EARUZ. This is appropriate for point-to-point RS-232 links, legacy serial consoles, and industrial equipment interfaces. Signal integrity and error-free operation also depend on cable length, connector wiring, grounding, and the baud rate used by the connected equipment.
Where can I download the ADM213EARUZ datasheet PDF?
The primary technical document is available through Analog Devices' official ADM213E product page at https://www.analog.com/en/products/adm213e.html. That page provides the manufacturer documentation for the ADM213E family and links to its data sheet. Use the manufacturer document when assigning pins, selecting charge-pump capacitors, checking logic thresholds, and confirming absolute maximum ratings before completing the PCB design.
Where can I find the ADM213EARUZ pinout?
The ADM213EARUZ pinout is defined in the pin-description table and package drawing in the Analog Devices manufacturer data sheet. The device uses a 28-pin TSSOP package. Assign the connector and external circuitry from that authoritative pin table rather than inferring functions from neighboring channels, because repeated driver and receiver groups can otherwise produce incorrect board wiring.
What can replace the ADM213EARUZ on the same PCB?
The directly documented pin-compatible choice is ADM213EARUZ-REEL7, which uses the same ADM213EARUZ electrical configuration in the same 28-pin TSSOP package but is supplied on a reel. The manufacturer supports both ADM213 and ADM213E product families, but the ADM213EARUZ-REEL and ADM213EARSZ references are not automatically drop-in replacements because package and ordering-code details must match the existing land pattern and assembled configuration.
Is ADM213EARUZ the same as ADM213EARUZ-REEL7?
ADM213EARUZ and ADM213EARUZ-REEL7 represent the same underlying ADM213EARUZ device configuration in the same 28-pin TSSOP package, with the ordering suffix principally identifying reel packaging. The ADM213EARUZ-REEL7 listing identifies it as a 4/5 full-RS232 transceiver in a 28-TSSOP package. Confirm the manufacturer ordering code and package drawing before substituting one ordering code for the other.
When should I choose ADM213EARUZ over a single-channel RS-232 transceiver?
Choose the ADM213EARUZ when the design needs four RS-232 drivers and five receivers on one +5 V device. Its 200 kbps rate supports multi-channel legacy serial links without requiring separate transceiver ICs for every direction. A single-channel device may be preferable for point-to-point links where four extra channels would add unused pins, higher board area, or unnecessary cost.
What is the best cross-brand equivalent for ADM213EARUZ?
No verified cross-brand, pin-compatible 28-pin TSSOP equivalent is established by the available manufacturer and distributor records. The documented alternative is the same-manufacturer ADM213EARUZ-REEL7 ordering option. Before approving a different manufacturer's device, verify the complete 28-pin assignment, charge-pump capacitor requirements, driver and receiver counts, shutdown behavior, and 200 kbps operating condition against the Analog Devices data sheet.
ADM213EARUZ versus ADM213EAR — which one fits an existing 28-pin design?
The ADM213EARUZ uses a 28-pin TSSOP package, while comparison data identifies ADM213EAR with a 28-pin SOIC package. They therefore are not drop-in alternatives for a fixed PCB because their lead geometry and land patterns differ. The ADM213EARUZ is the appropriate selection when the board footprint is TSSOP; the SOIC version requires a different footprint and must not be substituted without PCB changes.
Is ADM213EARUZ suitable for industrial and instrument-control applications?
The ADM213EARUZ is suitable for industrial serial interfaces when its +5 V supply, 200 kbps rate, four-driver and five-receiver configuration meet the system requirements. Analog Devices describes the ADM2xx family as intended for robust EIA-232-E and V.28 interfaces and for harsh electrical environments. Add suitable external surge protection, grounding, and connector-level isolation where the connected cable is exposed to industrial transients.
Does ADM213EARUZ have shutdown and enable controls?
The ADM213EARUZ includes shutdown and enable pins, and two of its five receivers remain active during shutdown. These functions help a system reduce interface power while preserving monitoring of selected incoming lines. According to the Analog Devices ADM213 product information, the ADM213 family provides a low-power shutdown mode intended to reduce power dissipation without losing access to two receive channels.
Where to buy ADM213EARUZ online and what is its lead time?
Use the Request a Quote form on this page to ask for current ADM213EARUZ availability, minimum order quantity, and lead time. Inventory and delivery schedules can change by package, quantity, and purchasing conditions, so request a current quotation for the exact 28-pin TSSOP ordering code. The Request a Quote form is the appropriate channel for commercial confirmation without relying on a potentially stale listing.

エンジニアリング参考データ: ADM213EARUZ — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose ADM213EARUZ when an existing board has a 28-pin TSSOP land pattern and the design requires four RS-232 drivers, five receivers, full-duplex operation, and a +5 V supply. It is particularly useful when shutdown must be combined with monitoring on two incoming status lines. The ADM213EARUZ-REEL7 ordering option is appropriate when the same device configuration is needed in reel-fed production; it changes the delivery format rather than the electrical design. Do not select ADM213EAR or ADM213EARSZ as direct drop-ins without checking the package, because comparison records identify a 28-pin SOIC option and a different ordering configuration. A single-channel transceiver such as MAX3221EIDBR may be more appropriate for a one-port design when the additional ADM213EARUZ channels would remain unused. For any substitute, verify the complete 28-pin assignment, 200 kbps class performance, charge-pump capacitor values, logic thresholds, and shutdown behavior.

代替品との比較

パラメータ この製品 ADM213EARUZ-REEL7
Package 28-pin TSSOP 28-pin TSSOP
Brand Analog Devices Analog Devices
Product Type RS-232 transceiver RS-232 transceiver
Supply Voltage +5 V +5 V
Data Rate 200 kbps 200 kbps class device
Driver Count 4 drivers 4 drivers
Receiver Count 5 receivers 5 receivers
Duplex Mode Full duplex Full duplex
Shutdown and Enable Shutdown and enable pins Shutdown and enable pins
Charge-Pump Capacitor 0.1 µF 0.1 µF

主な差別化要因

  • Integrates four drivers and five receivers in one interface IC (vs MAX3221EIDBR)
  • Supports monitoring while the main interface is shut down (vs ADM213EARUZ-REEL7)
  • Uses a single +5 V supply for RS-232 interface operation (vs MAX3221EIDBR)

設計ノート

Place the manufacturer's specified 0.1 µF charge-pump capacitors directly beside the corresponding ADM213EARUZ pins, with short, low-loop-area traces and a common ground return. Keep the RS-232 driver and receiver routes away from clocks, switching supplies, and high-slew-rate digital nets. The internal charge pump produces bipolar RS-232 voltage from +5 V, so bypassing and layout quality directly affect both output integrity and electromagnetic emissions.

Treat RS-232 as a point-to-point interface and route each driver output to the intended receiver input. Do not connect multiple driver outputs together, even when several channels appear unused. For long or noisy cables, use a consistent signal-ground reference, route the cable ground alongside the data conductors, and place external transient protection at the connector. The ADM213EARUZ's 200 kbps class operation does not remove the need for cable and grounding engineering.

Decouple the +5 V supply locally and ensure it can support both the logic load and the charge-pump current without excessive ripple. Use the Analog Devices recommended capacitor values and placement rather than adding arbitrary bulk capacitance that may destabilize the charge-pump node. Coordinate the enable and shutdown states in firmware so the active transmitters cannot be connected to another powered driver on the same RS-232 pair.

コンプライアンス情報

RoHS
Compliant
REACH
Compliant
AEC-Q100
Not Applicable
鉛フリー
Yes
ハロゲンフリー
Unknown
紛争鉱物
Unknown

The component record identifies RoHS3 compliance, REACH unaffected status, and lead-free ordering. Analog Devices states that the ADM213E family complies with the EU EMC directive identified as 89/336/EEC.

データ検証日: 2026-11-19 — データはXAIPARTの部品エンジニアリングチームによって検証・管理されています

関連検索

ADM213EARUZ datasheet ADM213EARUZ pinout ADM213EARUZ datasheet pdf ADM213EARUZ equivalent ADM213EARUZ replacement ADM213EARUZ cross reference ADM213EARUZ footprint ADM213EARUZ price ADM213EARUZ stock ADM213EARUZ application circuit Analog Devices ADM213EARUZ ADM213EARUZ 200 kbps TSSOP ADM213EARUZ vs ADM213EARUZ-REEL7 ADM213EARUZ vs MAX3221EIDBR what can replace ADM213EARUZ

関連部品&用語

Analog Devices ADM213EARUZ ADM213EARUZ-REEL7 ADM213 ADM213E MAX3221EIDBR RS-232 transceiver RS-232 interface IC line driver line receiver full-duplex communication EIA-232-E V.28 +5 V power supply 200 kbps data rate 0.1 µF charge-pump capacitor shutdown pin enable pin 28-pin TSSOP TSSOP package family surface-mount package industrial control test and measurement EMC directive 89/336/EEC RoHS REACH
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示