ATMEGA88PA-MUR - 8-bit AVR MCU 8KB Flash 20MHz QFN-32 | Microchip
部品番号: ATMEGA88PA-MUR ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $1.42 | $1.42 |
| 10 | $1.28 | $12.80 |
| 100 | $1.02 | $102.00 |
| 500 | $0.85 | $425.00 |
| 1,000 | $0.71 | $710.00 |
ATMEGA88PA-MUR 概要
An 8-bit AVR microcontroller is a single-chip computer that executes the Advanced RISC architecture, in which most of the 130 instructions complete in a single clock cycle, giving roughly 1 MIPS per MHz of performance. MCUs of this class sit at the low end of the microcontroller hierarchy, below 32-bit ARM devices, and are widely used where cost, power consumption, and code density matter more than raw processing throughput.
Key features include 23 programmable general-purpose I/O lines, 32 general-purpose working registers, an 8-channel 10-bit ADC (8 single-ended channels or differential pairs with programmable gain), three flexible timer/counters with compare and PWM modes, and serial peripherals including USART, SPI, and TWI (I2C). The picoPower technology delivers low sleep-mode currents, down to sub-uA levels in power-down mode with RTC running from a 32 kHz watch crystal.
Technical depth: the ATmega88PA is the picoPower-enhanced revision of the ATmega88 core, rated from 1.8 V to 5.5 V supply. It supports two on-chip oscillators (8 MHz RC and 128 kHz RC) plus an external crystal option, brown-out detection, watchdog timer, six sleep modes, and debugWIRE single-wire on-chip debugging. Program memory is ISP-flash with read-while-write capability, and the device can be self-programmed for bootloader applications.
Typical applications include battery-powered sensor nodes, industrial control and motor supervision, HVAC and appliance control, and hobby/embedded products such as Arduino-compatible boards. The wide 1.8 V to 5.5 V range allows direct battery or 5 V rail operation.
Design consideration: the QFN package requires an exposed die pad that must be soldered to a ground array for reliability; use via stitching under the pad for the best thermal and solder joint quality.
This page synthesizes verified distributor data, drop-in alternatives, application notes, and design guidance not found in a single manufacturer datasheet.
ドロップイン代替品: ATMEGA88PA-MUR — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: ATMEGA88PA-MUR （同一形状・フットプリント） — 相違点: Package, Timers/Counters, Supply Voltage Range, General Purpose I/O, Operating Temperature.
クイック比較ツール — 並列比較する代替部品を選択:
ATMEGA88PA-MU
✅ ドロップイン✓ 在庫あり
$1.26 / 個
データシートを見る →ATMEGA88PA-CCUR
✅ ドロップイン✓ 在庫あり
$1.08 / 個
データシートを見る →ATMEGA88A-MUR
✅ ドロップイン✓ 在庫あり
$1.38 / 個
データシートを見る →ATMEGA88PA-MMHR
✅ ドロップイン✓ 在庫あり
$2.05 / 個
データシートを見る →ATMEGA88-20MU
✅ ドロップイン✓ 在庫あり
価格はお問い合わせください
データシートを見る →ATMEGA88PA-MUR 最大定格＆電気的特性
| Core Processor | AVR 8-bit RISC |
| Core Size | 8-Bit |
| Speed | 20 MHz |
| Flash Memory | 8 KB (4K x 16) |
| EEPROM | 512 B |
| SRAM | 1 KB |
| 電源電圧 | 1.8 V to 5.5 V |
| General Purpose I/O | 23 |
| ADC Resolution | 10-bit, 8 channels |
| Timers/Counters | 2 x 8-bit, 1 x 16-bit |
| Communication Interfaces | USART, SPI, TWI (I2C) |
| 動作温度 | -40C to +85C (TA) |
| パッケージ | 32-VQFN (5x5 mm) exposed pad |
| 実装タイプ | Surface Mount |
| Oscillator Type | Internal |
| Programming | ISP Flash, self-programmable (bootloader) |
| Debug Interface | debugWIRE |
| Power Technology | picoPower |
| Instructions | 130 powerful instructions, mostly single-cycle |
ATMEGA88PA-MUR ピン構成
| ピン 1 | PD3 (PCINT19/OC2B/INT1) — Port D bit 3, pin change interrupt 19, Timer2 output compare B, external interrupt 1 |
| ピン 2 | PD4 (PCINT20/XCK/T0) — Port D bit 4, pin change interrupt 20, USART external clock, Timer0 external clock |
| ピン 3 | GND — Ground |
| ピン 4 | VCC — Digital supply voltage |
| ピン 5 | GND — Ground |
| ピン 6 | VCC — Digital supply voltage |
| ピン 7 | PB6 (PCINT6/XTAL1/TOSC1) — Port B bit 6, crystal pin 1 / timer oscillator input |
| ピン 8 | PB7 (PCINT7/XTAL2/TOSC2) — Port B bit 7, crystal pin 2 / timer oscillator output |
| ピン 9 | PD5 (PCINT21/OC0B/T1) — Port D bit 5, pin change interrupt 21, Timer0 output compare B, Timer1 external clock |
| ピン 10 | PD6 (PCINT22/OC0A/AIN0) — Port D bit 6, pin change interrupt 22, Timer0 output compare A, analog comparator positive input |
| ピン 11 | PD7 (PCINT23/AIN1) — Port D bit 7, pin change interrupt 23, analog comparator negative input |
| ピン 12 | PB0 (PCINT0/CLKO/ICP1) — Port B bit 0, pin change interrupt 0, system clock output, Timer1 input capture |
| ピン 13 | PB1 (PCINT1/OC1A) — Port B bit 1, pin change interrupt 1, Timer1 output compare A |
| ピン 14 | PB2 (PCINT2/SS/OC1B) — Port B bit 2, pin change interrupt 2, SPI slave select, Timer1 output compare B |
| ピン 15 | PB3 (PCINT3/MOSI/OC2A) — Port B bit 3, pin change interrupt 3, SPI master output, Timer2 output compare A |
| ピン 16 | PB4 (PCINT4/MISO) — Port B bit 4, pin change interrupt 4, SPI master input |
| ピン 17 | PB5 (PCINT5/SCK) — Port B bit 5, pin change interrupt 5, SPI clock |
| ピン 18 | AVCC — ADC supply voltage |
| ピン 19 | ADC6 — ADC input channel 6 |
| ピン 20 | AREF — Analog reference voltage for ADC |
| ピン 21 | GND — Ground |
| ピン 22 | ADC7 — ADC input channel 7 |
| ピン 23 | PC0 (PCINT8/ADC0) — Port C bit 0, pin change interrupt 8, ADC input channel 0 |
| ピン 24 | PC1 (PCINT9/ADC1) — Port C bit 1, pin change interrupt 9, ADC input channel 1 |
| ピン 25 | PC2 (PCINT10/ADC2) — Port C bit 2, pin change interrupt 10, ADC input channel 2 |
| ピン 26 | PC3 (PCINT11/ADC3) — Port C bit 3, pin change interrupt 11, ADC input channel 3 |
| ピン 27 | PC4 (PCINT12/SDA/ADC4) — Port C bit 4, pin change interrupt 12, TWI data line, ADC input channel 4 |
| ピン 28 | PC5 (PCINT13/SCL/ADC5) — Port C bit 5, pin change interrupt 13, TWI clock line, ADC input channel 5 |
| ピン 29 | PC6 (PCINT14/RESET) — Port C bit 6, pin change interrupt 14, reset input / debugWIRE |
| ピン 30 | PD0 (PCINT16/RXD) — Port D bit 0, pin change interrupt 16, USART receive |
| ピン 31 | PD1 (PCINT17/TXD) — Port D bit 1, pin change interrupt 17, USART transmit |
| ピン 32 | PD2 (PCINT18/INT0) — Port D bit 2, pin change interrupt 18, external interrupt 0 |
主な用途
ATMEGA88PA-MUR の用途: 6 件s: Battery-Powered Sensor Nodes, Industrial Control and Monitoring, Hobby and Arduino-Compatible Boards, Home Appliance Control, Human Interface Devices and Controls, Motor Control and Power Supervision.
Battery-Powered Sensor Nodes
The ATMEGA88PA-MUR fits battery-powered sensor nodes because its picoPower technology delivers sub-uA power-down currents and a wide 1.8 V to 5.5 V operating range that tracks a discharging lithium or alkaline cell directly. The internal 8 MHz RC oscillator removes the need for a crystal in coarse-timing nodes, cutting BOM cost and board area, while the 128 kHz RC oscillator supports low-power timing loops. A typical node sleeps in power-down with watchdog wakeups, samples with the 10-bit ADC, and transmits over USART or SPI to a radio module; because the ADC reference can be tied to VCC, a known supply enables ratiometric measurement without a dedicated reference IC. Designers should budget clock tolerance for RC-oscillator operation or add a watch crystal for accurate timekeeping.
おすすめ
Industrial Control and Monitoring
In industrial control panels, the ATMEGA88PA-MUR provides a cost-effective supervisory controller with -40C to +85C industrial temperature rating and brown-out detection that prevents corrupted operation during supply dips. The three timer/counters with PWM outputs drive relays, heaters, or small motors, while the 8-channel 10-bit ADC reads analog transducers such as 4-20 mA-conditioned process signals or potentiometers. TWI (I2C) connects front-panel displays and EEPROM configuration storage, and the USART links to modems or PLC backplanes. Because the part survives 5 V rails natively, it interfaces directly with legacy 5 V industrial logic without level shifters. For harsher enclosures exceeding +85C, the same-footprint ATMEGA88PA-CCUR extends the rating to +105C without a PCB redesign.
おすすめ
Hobby and Arduino-Compatible Boards
The ATMEGA88PA-MUR is well suited to Arduino-compatible and educational boards because it uses the same AVR ISP programming model, debugWIRE debugging, and bootloader ecosystem as the classic Arduino Uno ATmega328P, at lower cost and in a compact 5x5 mm QFN. With 8 KB Flash, roughly 6 KB remains after a 2 KB bootloader, which is enough for sensor reads, serial links, and small state machines but not for large libraries, so educators often target direct ISP sketches instead. The 23 GPIO lines support shields over SPI, I2C, and UART, and the internal RC oscillator enables crystal-less designs for wearables. Board designers should expose the reset pin (PC6) and SPI header for easy reprogramming of the QFN-mounted part.
おすすめ
Home Appliance Control
Home appliance controllers benefit from the ATMEGA88PA-MUR's combination of 5 V native operation, PWM timer outputs for triac or motor-drive control, and ADC channels for temperature sensing via NTC thermistors. The watchdog timer and brown-out detector provide the fault-tolerance expected in safety-adjacent appliance firmware, and the internal 8 MHz RC oscillator eliminates the crystal typically compromised by vibration or condensation in wash and cool environments. EEPROM (512 B) retains user settings and fault logs across power cycles. Sleep modes allow standby-power compliance targets in mains-off states. Designers should observe creepage and isolation rules on the PCB between the MCU domain and mains circuitry, and choose the +105C ATMEGA88PA-CCUR variant for oven-adjacent control boards.
おすすめ
Human Interface Devices and Controls
Key panels, rotary encoders, and capacitive touch front-ends map naturally onto the ATMEGA88PA-MUR: 23 GPIO lines handle key matrices and LEDs, PCINT pin-change interrupts wake the device from power-down on any keypress, and the 10-bit ADC with internal reference can implement simple capacitive sensing on spare channels. Timer PWM drives LED brightness dimming and buzzer tones with no CPU load. picoPower sleep currents are essential for battery remotes that must last years, and the internal 128 kHz RC oscillator can keep a soft timer running in idle. The USART eases communication with display drivers or wireless dongles. Layout practice: keep analog touch channels away from switching loads and use the exposed ground pad as the low-inductance return.
おすすめ
Motor Control and Power Supervision
The ATMEGA88PA-MUR supervises small motor drives by generating complementary PWM from the 16-bit Timer1, reading current via the ADC with differential inputs and programmable gain, and shutting down outputs through GPIO when faults occur. Fast analog-to-digital conversion at up to 10-bit resolution supports average current regulation for DC fans and pumps, while the 20 MHz clock provides the timer resolution needed for quiet PWM frequencies above the audible band. Brown-out detection protects flash integrity during supply sag at motor start. Because the ADC is ratiometric to VCC or an external reference on AREF, low-side shunt sensing is straightforward. For designs needing faster 16-bit PWM resolution or CAN, Microchip's ATmega64M1 family is the recommended next step up within the same AVR ecosystem.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: ATMEGA88PA-MUR — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | ATMEGA88PA-MU | ATMEGA88PA-CCUR | ATMEGA88A-MUR | ATMEGA88PA-MMHR | ATMEGA88-20MU |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | VQFN-32 (5x5 mm) | VQFN-32 (5x5 mm) - same | VQFN-32 (5x5 mm) - same | VQFN-32 (5x5 mm) - same | VQFN-32 (5x5 mm) - same | VQFN-32 (5x5 mm) - same |
| Flash Memory | 8 KB | 8 KB | 8 KB | 8 KB | 8 KB | 8 KB |
| Maximum Clock | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz |
| Supply Voltage Range | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 2.7 V to 5.5 V |
| picoPower Technology | Yes | Yes | Yes | No | Yes | No |
| Packing | Tape & Reel | Tray | Tape & Reel | Tape & Reel | Tape & Reel | Tray |
主な差別化要因
- picoPower sleep performance （vs ATMEGA88A-MUR)
- Extended temperature option in same footprint （vs ATMEGA88PA-CCUR)
- Cost-efficient memory point （vs ATMEGA328P)
設計ノート
The QFN exposed die pad must be soldered to ground for mechanical reliability and EMC. Use a solder-mask-defined array of via-in-pad openings (4-6 vias) connecting to internal ground planes; do not leave the pad unconnected even though the ATmega88PA die pad is nominally ground. Follow the Microchip MLF/QFN assembly application guidance for stencil design - roughly 50-70% pad coverage with ventilation channels to prevent voiding and float during reflow.
Decouple each VCC pin (pins 4 and 6) and AVCC (pin 18) with 100 nF ceramic capacitors placed within 2 mm of the pins, plus one bulk 4.7-10 uF per rail. Tie AVCC to VCC through an RC filter (e.g., 10 ohm + 100 nF) when ADC accuracy matters, keeping AVCC between 1.8 V and VCC. Enable the internal brown-out detector at 2.7 V for 5 V systems to prevent flash corruption during brown-out events.
Keep the reset pin (PC6/debugWIRE) trace short and add a 10 k-47 k pull-up; avoid driving it during power-up or debugWIRE will be disabled by external circuitry contention. If using PB6/PB7 as GPIO instead of a crystal, note their weaker drive configuration. Maintain series resistance of 100-200 ohms on ISP lines (PB3-PB5) if they are shared with peripheral loads so programming is not blocked.
Clock speed is voltage-limited: 20 MHz requires VCC near 4.5-5.5 V, whereas a 3.3 V design should not exceed roughly 13.3 MHz on an external clock (the safe internal-oscillator choice is 8 MHz). Attempting 20 MHz at 3.3 V causes unreliable operation. Also remember PC6 is reset by default - using it as GPIO requires setting the RSTDISBL fuse, which permanently disables further ISP reprogramming.
コンプライアンス情報
RoHS compliant and lead-free per Microchip green packaging for the ATmega88PA family (distributor listings). REACH/halogen/conflict-minerals declarations should be confirmed via the current Microchip certificate of conformance.
