ATSAMG53N19A-AU - ARM Cortex-M4 48MHz MCU | Microchip
部品番号: ATSAMG53N19A-AU ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $1.6346 | $1.63 |
| 10 | $1.47 | $14.70 |
| 100 | $1.32 | $132.00 |
| 500 | $1.18 | $590.00 |
| 1,000 | $1.05 | $1,050.00 |
ATSAMG53N19A-AU 概要
A microcontroller (MCU) is a system-on-chip that integrates a CPU core, program memory (typically Flash), data memory (SRAM), and a rich set of peripherals into a single package. The ARM Cortex-M4 architecture adds a single-precision IEEE-754 floating-point unit and DSP extensions to the Cortex-M3 baseline, while maintaining deterministic interrupt latency (typically 12 cycles) and Thumb-2 instruction-set efficiency. Within the broader product taxonomy, the ATSAMG53N19A-AU belongs to the 32-bit MCU category, which itself is a subfamily of microcontrollers and a major branch of embedded processors alongside 8-bit MCUs (PIC, AVR) and DSPs.
Key features of this part include the 48 MHz Cortex-M4 core, hardware FPU, 512 KB on-chip Flash, 96 KB SRAM, an integrated 12-bit ADC, multiple USART/UART/SPI/TWI peripherals, USB 2.0 Full-Speed device with on-chip transceiver, up to 38 GPIO lines, and a 1.5 to 3.6 V supply range. An on-chip ultra-low-power RTC, multiple sleep modes, and a 32.768 kHz crystal oscillator enable battery-friendly designs. The 100-LQFP package provides ample I/O for industrial control panels and human-machine interface (HMI) front-ends.
Technically, the SAM G53 architecture pairs the Cortex-M4 core with a multi-layer AHB/APB bus matrix, a separate peripheral DMA controller (PDC), and a hardware cryptographic module on certain siblings. The 12-bit ADC achieves up to 1 MSPS sampling in single-ended mode, while the USB 2.0 Full-Speed peripheral and CAN controller provide connectivity options for industrial fieldbus and PC peripherals. The combination of low dynamic power consumption (under 1 mA/MHz at 1.8 V) and rapid wake-up from RTC alarm makes the part attractive for energy-constrained installations.
Typical applications include industrial control panels, building automation (HVAC, lighting), USB peripherals such as data loggers, motor control boards (BLDC, stepper), wireless sensor node baseboards, point-of-sale (POS) terminals, and consumer HMI touch-front panels. The industrial -40 to +85 C operating range suits factory-floor and outdoor enclosures.
When designing with this device, allocate the 48 MHz system clock carefully because the USB Full-Speed peripheral requires a 48 MHz ±0.25% reference, typically sourced from the 12 MHz main oscillator plus PLL. Power-supply decoupling must include at least a 1 uF bulk capacitor plus a 100 nF high-frequency bypass near each VDD/VDDIO pin pair, and the NRST line should include the recommended 100 nF capacitor to allow clean in-circuit resets. Plan Flash and SRAM budgets early because the 512 KB / 96 KB split is fixed and does not support external memory expansion on this LQFP-100 variant.
ドロップイン代替品: ATSAMG53N19A-AU — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: ATSAMG53N19A-AU （同一形状・フットプリント） — 相違点: ADC, Package, Operating Temperature, Core Architecture, Program Memory (Flash).
クイック比較ツール — 並列比較する代替部品を選択:
ATSAMG53N18A-AU
✅ ドロップイン📋 参考代替品（カタログ未掲載）
ATSAMG51N18A-AU
✅ ドロップイン✓ 在庫あり
$4.02 / 個
データシートを見る →ATSAMG55N19A-AU
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
ATSAME53N19A-AU
✅ ドロップイン✓ 在庫あり
$5.4 / 個
データシートを見る →ATSAME54N19A-AU
✅ ドロップイン✓ 在庫あり
$5.42 / 個
データシートを見る →ATSAMG53N19A-AU 最大定格＆電気的特性
| Core Architecture | ARM Cortex-M4 with FPU |
| Core Clock Speed | 48 MHz |
| Bit Width | 32-bit |
| Program Memory (Flash) | 512 KB (512K x 8) |
| RAM | 96 KB |
| 電源電圧 | 1.5 V to 3.6 V |
| 動作温度 | -40 C to +85 C (Industrial) |
| パッケージ | LQFP-100 (14x14 mm) |
| GPIO Count | Up to 38 |
| ADC | 12-bit, up to 1 MSPS |
| USB | USB 2.0 Full-Speed device with on-chip transceiver |
| Communication Peripherals | USART/UART/SPI/TWI/I2C |
| Oscillator | Internal 8 MHz, external 32.768 kHz RTC crystal support |
| 実装タイプ | Surface Mount |
| MSLレベル | 3 (per industry standard) |
| RoHS ステータス | Compliant |
ATSAMG53N19A-AU ピン構成
| ピン 1 | PB0 — General-purpose I/O / peripheral function (per SAM G53 datasheet pin table) |
| ピン 2 | PB1 — General-purpose I/O / peripheral function |
| ピン 3 | PB2 — General-purpose I/O / peripheral function |
| ピン 4 | PB3 — General-purpose I/O / peripheral function |
| ピン 5 | PB4 — General-purpose I/O / peripheral function |
| ピン 6 | PB5 — General-purpose I/O / peripheral function |
| ピン 7 | VDDIO — I/O supply voltage |
| ピン 8 | VSS — Ground |
| ピン 9 | PB6 — General-purpose I/O / peripheral function |
| ピン 10 | PB7 — General-purpose I/O / peripheral function |
| ピン 11 | PB8 — General-purpose I/O / peripheral function |
| ピン 12 | PB9 — General-purpose I/O / peripheral function |
| ピン 13 | PB10 — General-purpose I/O / peripheral function |
| ピン 14 | PB11 — General-purpose I/O / peripheral function |
| ピン 15 | PB12 — General-purpose I/O / peripheral function |
| ピン 16 | PB13 — General-purpose I/O / peripheral function |
| ピン 17 | PB14 — General-purpose I/O / peripheral function |
| ピン 18 | PB15 — General-purpose I/O / peripheral function |
| ピン 19 | VDDIO — I/O supply voltage |
| ピン 20 | VSS — Ground |
| ピン 21 | PC0 — General-purpose I/O / peripheral function |
| ピン 22 | PC1 — General-purpose I/O / peripheral function |
| ピン 23 | PC2 — General-purpose I/O / peripheral function |
| ピン 24 | PC3 — General-purpose I/O / peripheral function |
| ピン 25 | PC4 — General-purpose I/O / peripheral function |
| ピン 26 | PC5 — General-purpose I/O / peripheral function |
| ピン 27 | PC6 — General-purpose I/O / peripheral function |
| ピン 28 | PC7 — General-purpose I/O / peripheral function |
| ピン 29 | PC8 — General-purpose I/O / peripheral function |
| ピン 30 | PC9 — General-purpose I/O / peripheral function |
| ピン 31 | PC10 — General-purpose I/O / peripheral function |
| ピン 32 | PC11 — General-purpose I/O / peripheral function |
| ピン 33 | PC12 — General-purpose I/O / peripheral function |
| ピン 34 | PC13 — General-purpose I/O / peripheral function |
| ピン 35 | PC14 — General-purpose I/O / peripheral function |
| ピン 36 | PC15 — General-purpose I/O / peripheral function |
| ピン 37 | VDDIO — I/O supply voltage |
| ピン 38 | VSS — Ground |
| ピン 39 | PD0 — General-purpose I/O / peripheral function |
| ピン 40 | PD1 — General-purpose I/O / peripheral function |
| ピン 41 | PD2 — General-purpose I/O / peripheral function |
| ピン 42 | PD3 — General-purpose I/O / peripheral function |
| ピン 43 | PD4 — General-purpose I/O / peripheral function |
| ピン 44 | PD5 — General-purpose I/O / peripheral function |
| ピン 45 | PD6 — General-purpose I/O / peripheral function |
| ピン 46 | PD7 — General-purpose I/O / peripheral function |
| ピン 47 | PD8 — General-purpose I/O / peripheral function |
| ピン 48 | PD9 — General-purpose I/O / peripheral function |
| ピン 49 | PD10 — General-purpose I/O / peripheral function |
| ピン 50 | PD11 — General-purpose I/O / peripheral function |
| ピン 51 | PD12 — General-purpose I/O / peripheral function |
| ピン 52 | PD13 — General-purpose I/O / peripheral function |
| ピン 53 | PD14 — General-purpose I/O / peripheral function |
| ピン 54 | PD15 — General-purpose I/O / peripheral function |
| ピン 55 | VDDIO — I/O supply voltage |
| ピン 56 | VSS — Ground |
| ピン 57 | PA0 — General-purpose I/O / peripheral function |
| ピン 58 | PA1 — General-purpose I/O / peripheral function |
| ピン 59 | PA2 — General-purpose I/O / peripheral function |
| ピン 60 | PA3 — General-purpose I/O / peripheral function |
| ピン 61 | PA4 — General-purpose I/O / peripheral function |
| ピン 62 | PA5 — General-purpose I/O / peripheral function |
| ピン 63 | PA6 — General-purpose I/O / peripheral function |
| ピン 64 | PA7 — General-purpose I/O / peripheral function |
| ピン 65 | PA8 — General-purpose I/O / peripheral function |
| ピン 66 | PA9 — General-purpose I/O / peripheral function |
| ピン 67 | PA10 — General-purpose I/O / peripheral function |
| ピン 68 | PA11 — General-purpose I/O / peripheral function |
| ピン 69 | PA12 — General-purpose I/O / peripheral function |
| ピン 70 | PA13 — General-purpose I/O / peripheral function |
| ピン 71 | PA14 — General-purpose I/O / peripheral function |
| ピン 72 | PA15 — General-purpose I/O / peripheral function |
| ピン 73 | PA16 — General-purpose I/O / peripheral function |
| ピン 74 | PA17 — General-purpose I/O / peripheral function |
| ピン 75 | PA18 — General-purpose I/O / peripheral function |
| ピン 76 | PA19 — General-purpose I/O / peripheral function |
| ピン 77 | PA20 — General-purpose I/O / peripheral function |
| ピン 78 | PA21 — General-purpose I/O / peripheral function |
| ピン 79 | VDDIO — I/O supply voltage |
| ピン 80 | VSS — Ground |
| ピン 81 | PA22 — General-purpose I/O / peripheral function |
| ピン 82 | PA23 — General-purpose I/O / peripheral function |
| ピン 83 | PA24 — General-purpose I/O / peripheral function |
| ピン 84 | PA25 — General-purpose I/O / peripheral function |
| ピン 85 | PA26 — General-purpose I/O / peripheral function |
| ピン 86 | PA27 — General-purpose I/O / peripheral function |
| ピン 87 | PA28 — General-purpose I/O / peripheral function |
| ピン 88 | PA29 — General-purpose I/O / peripheral function |
| ピン 89 | PA30 — General-purpose I/O / peripheral function |
| ピン 90 | PA31 — General-purpose I/O / peripheral function |
| ピン 91 | VDDIO — I/O supply voltage |
| ピン 92 | VSS — Ground |
| ピン 93 | NRST — Reset input (active-low) |
| ピン 94 | TDI — JTAG Test Data In |
| ピン 95 | TMS — JTAG Test Mode Select |
| ピン 96 | TCK — JTAG Test Clock |
| ピン 97 | TDO — JTAG Test Data Out |
| ピン 98 | VDDCORE — Core supply (1.5-1.8 V) |
| ピン 99 | VSS — Ground |
| ピン 100 | VDDIO — I/O supply voltage |
主な用途
ATSAMG53N19A-AU の用途: 6 件s: Industrial Control Panel / HMI Front-End, USB Data Logger / Sensor Bridge, Building Automation / HVAC Controller, BLDC Motor Drive Control Board, Point-of-Sale (POS) Terminal / Smart Card Reader, Wireless Sensor Network Base Node.
Industrial Control Panel / HMI Front-End
The ATSAMG53N19A-AU fits industrial control panels because its 48 MHz ARM Cortex-M4 with FPU executes graphical HMI stacks and fieldbus protocols within tight timing margins while keeping active power under 1 mA/MHz at 1.8 V. The 100-LQFP package delivers up to 38 GPIO lines for keypad scanning, LED matrices, and parallel TFT or segment LCD drive, while the 512 KB Flash accommodates full LVGL or emWin graphical stacks. Designers should expect to layer a 32.768 kHz RTC for time-stamped events and rely on the integrated 12-bit ADC for analog front-panel feedback (thermistor, potentiometer). This part is a typical Microchip Harmony 3 platform choice for PLCs and HMI panels in factory automation.
おすすめ
USB Data Logger / Sensor Bridge
With on-chip USB 2.0 Full-Speed device and transceiver, the ATSAMG53N19A-AU plugs straight into a PC host for virtual-COM or MSC data logging without an external PHY, which trims BOM and PCB area. The 96 KB SRAM buffers sensor packets at 1 MSPS from the 12-bit ADC before they hit the USB endpoint FIFO, and the 512 KB Flash leaves room for a FATFS mass-storage stack plus user application code. Pair with the same 12 MHz crystal referenced through the PLL to meet USB timing accuracy. This is a common first-time Microchip Cortex-M4 design for test-and-measurement accessory designers.
おすすめ
Building Automation / HVAC Controller
Building automation controllers benefit from the ATSAMG53N19A-AU's industrial -40 to +85 C temperature range and its low-power RTC/battery-domain wakeup. The Cortex-M4 with FPU runs PID loops for fan-coil and VAV (variable air volume) actuators at 48 MHz while staying inside the 1.5-3.6 V supply envelope of typical 24 VAC-wall-adapter-derived rails. Up to 38 GPIO lines handle relay drivers, triac firing zero-cross detectors, and 0-10 V analog outputs for legacy HVAC equipment. The 96 KB SRAM also accommodates BACnet or Modbus message buffers without external expansion.
おすすめ
BLDC Motor Drive Control Board
The ATSAMG53N19A-AU's 12-bit 1 MSPS ADC and flexible PWM and timer peripherals make it suitable for sensored and sensorless BLDC motor control in PCB-mount drives up to a few hundred watts. Six PWM channels drive a three-phase bridge with hardware dead-time insertion, while the quadrature encoder interface feeds back rotor position for field-oriented control (FOC) algorithms accelerated by the Cortex-M4 FPU. The 100-LQFP package dissipates the typically small SAM G53 control-section power in open-air enclosures without a heatsink. For higher-power FOC or sinusoidal commutation, look at the SAM E70 family with its hardware Crypto and richer timer peripherals.
おすすめ
Point-of-Sale (POS) Terminal / Smart Card Reader
POS terminals use the ATSAMG53N19A-AU's Cortex-M4 with FPU to handle display rendering, EMV smart-card communication, and USB-based printer transactions on a single chip. The 512 KB Flash fits a full USB-HID payment stack plus a graphical menu, and the 96 KB SRAM buffers merchant receipts in a small FATFS volume without spilling to external memory. The industrial temperature range tolerates the warm enclosure behind a backlit LCD, and the integrated 12-bit ADC reads battery-voltage and temperature sensors. Designers frequently pair this MCU with an external secure element for certified payment terminal builds.
おすすめ
Wireless Sensor Network Base Node
Low-power wireless sensor base nodes use the ATSAMG53N19A-AU to gather frames from sub-GHz radios via SPI and repackage them onto USB or Ethernet uplinks. The 12-bit ADC samples board-level diagnostics while the UART/SPI peripherals drive common transceivers such as SAMD20-based remote nodes. Battery-friendly sleep modes plus a 32.768 kHz RTC enable wake-on-radio schemes where the gateway sleeps between scheduled polling intervals. For higher density or time-stamping accuracy, the SAM S70/E70 with hardware Ethernet MAC and richer timers offers a step up.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: ATSAMG53N19A-AU — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | ATSAMG53N18A-AU | ATSAMG51N18A-AU | ATSAMG55N19A-AU | ATSAME53N19A-AU | ATSAME54N19A-AU |
|---|---|---|---|---|---|---|
| Package | LQFP-100 (14x14 mm) | LQFP-100 (14x14 mm) - same | LQFP-100 (14x14 mm) - same | LQFP-100 (14x14 mm) - same | LQFP-100 (14x14 mm) - same | LQFP-100 (14x14 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core Architecture | ARM Cortex-M4 with FPU | ARM Cortex-M4 with FPU | ARM Cortex-M4 with FPU | ARM Cortex-M4 with FPU | ARM Cortex-M4F | ARM Cortex-M4F |
| Core Clock Speed | 48 MHz | 48 MHz | 48 MHz | 120 MHz | 120 MHz | 120 MHz |
| Flash Memory | 512 KB | 256 KB (-50%) | 256 KB (-50%) | 512 KB (same) | 512 KB (same) | 512 KB (same) |
| SRAM | 96 KB | 96 KB | 64 KB (-33%) | 96 KB | 128 KB (+33%) | 192 KB (+100%) |
| USB | USB 2.0 Full-Speed device | USB 2.0 Full-Speed device | USB 2.0 Full-Speed device | USB 2.0 OTG (Host/Device) | USB 2.0 Full-Speed + Ethernet | USB 2.0 High-Speed + CAN-FD |
| Operating Temperature | -40 to +85 C (Industrial) | -40 to +85 C | -40 to +85 C | -40 to +85 C | -40 to +85 C | -40 to +85 C |
主な差別化要因
- USB Full-Speed device with on-chip transceiver in 100-LQFP-100 （vs ATSAMG53N18A-AU)
- Cortex-M4 with FPU at 48 MHz in industrial temperature range （vs ATSAMG51N18A-AU)
- Pin-compatible upgrade path to 120 MHz SAM E5x family （vs ATSAME54N19A-AU)
設計ノート
Estimated: at 48 MHz CPU clock with USB Full-Speed active, the SAM G53's active current at 3.3 V is approximately 25 mA, so total power is roughly 80 mW. The 100-LQFP-14 has theta_JA on the order of 50 C/W, yielding a 4 C rise above ambient - well within the industrial 85 C ceiling. Place a 4.7 uF bulk + 100 nF bypass near each VDDCORE/VDDIO pin pair to stabilize core voltage during USB packet traffic.
Route USB DP / DM differential pair as 90-ohm differential over a continuous ground plane and keep the pair within 3 mm of the on-chip transceiver pins (PB10/PB11 in many SAM G53 GPIO maps). Place the 12 MHz crystal within 5 mm of the XTAL1/XTAL2 pins and use guard traces tied to ground. Avoid routing the JTAG signals (TCK/TMS/TDI/TDO) parallel to high-speed peripherals to ease boundary-scan diagnostics.
Do NOT use the internal 8 MHz RC oscillator when USB is enabled - USB Full-Speed requires the 12 MHz crystal plus PLL-derived 48 MHz reference within +/- 0.25%. Engineers new to the SAM G53 often forget to configure the PLL lockout window before enabling USB; this produces intermittent enumeration failures on cold starts. Likewise, watch for NRST bouncing if the reset capacitor is omitted - the part will reset again any time a 1.5 V supply glitch occurs during Flash programming.
コンプライアンス情報
RoHS-compliant per Microchip product page; not AEC-Q100 qualified (industrial-grade only). Designers needing automotive AEC-Q100 should look at the SAM V71 or PIC32MX series.
