Microchip Technology

ATTINY24A-CCU - 20MHz AVR 2KB Flash MCU | Microchip Technology

部品番号: ATTINY24A-CCU ✓ 生産中
1.8 V to 5.5 V Vdss 15-UFBGA (3 x 3 mm) Package 20 MHz Speed 2 KB (1K x 16) Memory
MOQ: 1 |

ATTINY24A-CCU 概要

Microchip Technology ATTINY24A-CCU is a picoPower 8-bit AVR RISC microcontroller with a 20 MHz maximum clock, 2 KB of in-system-programmable Flash memory, and a 15-UFBGA package measuring 3 x 3 mm. The device provides 128 bytes of EEPROM, 128 bytes of SRAM, 12 general-purpose I/O lines, and 32 general-purpose working registers for compact embedded-control designs.

An 8-bit AVR microcontroller is a low-complexity embedded processor that executes instructions using an accumulator-and-register architecture. The ATTINY24A belongs to Microchip's ATtiny family and combines general-purpose I/O, timers, analog conversion, serial communication, and nonvolatile program and data memory in one compact device. Its picoPower architecture is intended to balance responsive processing with low power consumption in battery-operated and embedded systems.

Key features include a 20 MHz clock, 2 KB of ISP Flash, 128 bytes of EEPROM, 128 bytes of SRAM, and 12 general-purpose I/O lines. An 8-bit timer/counter provides two PWM channels, while the device also incorporates USI and ADC functionality. These resources allow the ATTINY24A-CCU to handle sensing, control, communication, and actuator tasks without requiring a larger external processor.

The microcontroller's compact 3 x 3 mm 15-UFBGA package makes it suitable for space-constrained products. The manufacturer identifies the device as an industrial-temperature part with a 1.8 V to 5.5 V operating range. Its memory organization supports small firmware images, while EEPROM provides nonvolatile storage for calibration values, configuration parameters, and operating counters. SRAM remains comparatively limited, so firmware should avoid unnecessary buffering and deep call nesting.

Typical uses include low-cost sensor interfaces, LED lighting controllers, compact motor controls, industrial modules, and small consumer products. The ADC is useful for analog measurements, while the USI can support serial communication arrangements. The two PWM outputs are useful for dimming, proportional control, or driving low-power loads, subject to the electrical limits of the selected I/O and power-supply design.

PCB design should preserve access to programming and power pins while accounting for the compact BGA land pattern. Place decoupling capacitance close to the supply pins, route high-current and sensitive analog signals deliberately, and follow the manufacturer's pin and land-pattern guidance. Because the package is only 3 x 3 mm, assembly capability, solder paste volume, and inspection access should be confirmed before committing to volume production.

This product page combines the manufacturer's device description, package and memory characteristics, ordering information, verified distribution listings, engineering application guidance, and a specification comparison for faster component selection and PCB planning.

ドロップイン代替品: ATTINY24A-CCU — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

この製品に利用可能なドロップイン代替品はありません。

代替品をリクエスト

ATTINY24A-CCU 最大定格&電気的特性

Product Type 8-bit AVR RISC microcontroller
最大クロック周波数 20 MHz
Flash Memory 2 KB (1K x 16)
EEPROM Memory 128 bytes
SRAM 128 bytes
General-Purpose I/O Lines 12
General-Purpose Working Registers 32
Timer/Counter 8-bit timer/counter
PWM Channels 2
ADC Available
USI Available
Operating Voltage Range 1.8 V to 5.5 V
Temperature Grade Industrial
パッケージ 15-UFBGA (3 x 3 mm)
Programming In-system programming

ATTINY24A-CCU 15-ufbga (3 x 3 mm) ピン配置ガイド

ATTINY24A-CCU (15-ufbga (3 x 3 mm) パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。

ATTINY24A-CCU の 15-ufbga (3 x 3 mm) パッケージピン配置図

詳細なピン配置データはありません: ATTINY24A-CCU.

詳細は データシート をご参照ください。

主な用途

ATTINY24A-CCU の用途: 6 件s: Compact Sensor Interface, LED Dimming Controller, Industrial Control Module, Low-Power Data Logger, Small Motor Control, Portable Consumer Accessory.

🧩

Compact Sensor Interface

The ATTINY24A-CCU fits compact sensor modules that need local conversion, configuration, and control without a larger processor. Its 10-bit ADC capability can sample analog sensor signals, while the USI provides a path to serial communication with a host or peripheral. The 20 MHz clock allows responsive filtering and calibration, and 2 KB of ISP Flash accommodates a focused embedded firmware image. With only 128 bytes of SRAM, the firmware should process samples incrementally rather than buffering large histories. The 3 x 3 mm 15-UFBGA package also reduces board area, although the compact land pattern requires assembly capability suited to fine-pitch BGAs.

💡

LED Dimming Controller

The ATTINY24A-CCU is suitable for compact LED dimming and lighting-control modules because its timer/counter provides two PWM channels and its 12 I/O lines support switches, indicators, and fault signaling. The 20 MHz operating clock gives adequate control-loop headroom for flicker management and current adjustment, while the ADC can monitor a feedback or sensing input. The device operates from 1.8 V to 5.5 V, allowing integration with both low-voltage and 5 V lighting architectures. Designers should size the PWM and ADC pathways independently because only two PWM outputs are available, and should ensure the LED driver remains electrically isolated from sensitive timing functions.

🏭

Industrial Control Module

The ATTINY24A-CCU works well in small industrial-control modules that combine discrete inputs, local feedback, and a serial supervisory interface. Twelve general-purpose I/O lines can handle digital controls, while the ADC supports analog process monitoring and the USI assists with peripheral communication. Its industrial-temperature classification makes it appropriate for temperature ranges beyond typical consumer-only designs, subject to correct decoupling and enclosure design. The 20 MHz clock and 2 KB Flash constrain firmware complexity, so divide larger functions among neighboring controllers and retain only real-time decisions on this device.

🔋

Low-Power Data Logger

The ATTINY24A-CCU can serve as the controller in a small, periodically active data logger when application data can fit within its 2 KB program memory and 128 bytes of SRAM. The picoPower architecture supports the low-power operating concept, and the ADC can acquire the quantity being logged. EEPROM provides 128 bytes of nonvolatile storage for counters, calibration constants, or a small status record. Firmware should wake only when required, sample and store incrementally, and return the device to sleep to conserve battery energy. The 3 x 3 mm package helps reduce board size, but regulator quiescent current and sensor standby behavior will dominate final battery life.

⚡

Small Motor Control

The ATTINY24A-CCU is suitable for modest motor or actuator-control tasks where size and power matter more than extensive computation. Its two PWM outputs can command a driver stage, and the ADC can support basic current, position, or speed feedback when the external signal is properly conditioned. The 20 MHz clock provides timely control-loop execution, while 128 bytes of SRAM is adequate for simple state machines that avoid large motion buffers. A microcontroller cannot safely drive a motor directly; use a suitable driver, protection circuitry, and a defined fault shutdown path. Validate stall current and thermal performance in the final mechanical system.

📱

Portable Consumer Accessory

The ATTINY24A-CCU fits small portable accessories that require a few inputs, a serial link, and compact board area. Its 15-UFBGA package leaves more room for batteries, sensors, connectors, or RF circuitry, and the 1.8 V to 5.5 V operating range supports low-energy power architectures. The 20 MHz AVR core can manage button handling, status LEDs, and simple accessory protocols, while USI and ADC broaden the available peripheral options. Firmware must remain compact because Flash is 2 KB and SRAM is 128 bytes. Verify connector accessibility, programming access, and assembly yield before using such a small package in a high-volume consumer design.

What are the key specifications of ATTINY24A-CCU that engineers should know?
The ATTINY24A-CCU is a 20 MHz, 8-bit AVR microcontroller with 2 KB of ISP Flash, 128 bytes of EEPROM, 128 bytes of SRAM, and 12 general-purpose I/O lines in a 15-UFBGA package. According to the Microchip manufacturer product page, it also provides 32 working registers, an 8-bit timer/counter with two PWM channels, USI, and ADC capability. The compact 3 x 3 mm package suits small embedded products, while the 2 KB memory limit requires careful firmware sizing.
What is the ATTINY24A-CCU and where is its datasheet PDF?
The ATTINY24A-CCU is a Microchip ATtiny24A-family, picoPower 8-bit AVR microcontroller with 2 KB Flash and a 15-UFBGA package. The manufacturer product page is available at https://www.microchip.com/en-us/product/ATtiny24A, while the component-specific datasheet landing page is https://octopart.com/datasheet/microchip/ATTINY24A-CCU. Use the manufacturer document for the authoritative pin configuration, electrical limits, programming connections, and package drawings.
Where is the ATTINY24A-CCU pinout located?
The ATTINY24A-CCU pinout is documented in the ATtiny24A manufacturer datasheet, whose product entry is https://www.microchip.com/en-us/product/ATtiny24A. The device uses a 15-UFBGA package with 15 signal and power positions, so the package drawing and pin-description table should be consulted before assigning PCB nets. Use the exact -CCU ordering code when cross-checking the 3 x 3 mm land pattern.
How do I program an ATTINY24A-CCU?
The ATTINY24A-CCU is programmed through its in-system programming interface, with the ISP clock, data, and target voltage connections defined in the manufacturer datasheet. Its 20 MHz maximum operating frequency applies after the programmed fuse settings are selected. Keep the ISP interface accessible when possible, use a supported programmer and programming adapter, and confirm the device's clock, brownout, and lock-bit configuration before production programming.
What is the operating voltage range of ATTINY24A-CCU?
The ATTINY24A-CCU operates from 1.8 V to 5.5 V in the industrial-temperature configuration. According to the manufacturer product description and the device-family technical information, this range supports both low-voltage and conventional 5 V embedded systems. The selected regulator, decoupling network, ADC reference, and I/O levels must remain compatible with the chosen supply voltage.
What can replace the ATTINY24A-CCU on the same PCB?
No independently verified drop-in replacement is established for the ATTINY24A-CCU because pin compatibility, firmware support, and electrical matching must all be confirmed. The -CCUR ordering code may represent a tape-and-reel shipment form of the same 15-UFBGA device, but it is not counted as a distinct functional alternative. Use Microchip's cross-reference search and the manufacturer datasheet before considering any substitution for a populated production PCB.
Is the ATTINY24A-CCU the same as the ATTINY24A-SSU?
The ATTINY24A-CCU and ATTINY24A-SSU belong to the same ATtiny24A device family, but they do not use the same PCB footprint. The ATTINY24A-CCU uses a 15-UFBGA package measuring 3 x 3 mm, whereas the ATTINY24A-SSU uses a 14-pin SOIC package. Their shared family membership does not make them pin-to-pin replacements, so the -SSU version requires a different PCB footprint.
ATTINY24A-CCU vs ATTINY24V-10SSUR: which is better for a new design?
The ATTINY24A-CCU and ATTINY24V-10SSUR are not direct drop-in alternatives because their packages and ordering codes differ. The ATTINY24A-CCU is the compact 15-UFBGA option, while the ATTINY24V-10SSUR is a 10 MHz SSUR variant. A new space-constrained design may favor the 20 MHz ATTINY24A-CCU, but firmware, supply voltage, pin assignment, and PCB layout must be evaluated rather than treating the two as interchangeable.
When should I choose ATTINY24A-CCU over a larger ATtiny microcontroller?
Choose the ATTINY24A-CCU when the design needs only a 20 MHz AVR controller, 2 KB of Flash, 128 bytes each of SRAM and EEPROM, and 12 I/O lines. Its 15-UFBGA package reduces PCB area, but the 128-byte SRAM limit and 2 KB Flash capacity require a compact firmware architecture. Select a larger ATtiny device when the application needs more memory, timers, communication peripherals, or application code space.
Is ATTINY24A-CCU suitable for a compact battery-powered sensor product?
The ATTINY24A-CCU is suitable for many compact battery-powered sensor products because it combines a 20 MHz AVR core, low-power picoPower architecture, ADC capability, USI, and 2 KB of Flash in a 3 x 3 mm package. The operating range extends down to 1.8 V. Final battery life depends on the sleep mode, ADC duty cycle, regulator efficiency, and pull networks, which should be measured in the complete product.
What are the trade-offs of using ATTINY24A-CCU in an LED controller?
The ATTINY24A-CCU provides two PWM channels, 12 I/O lines, ADC capability, and enough Flash for a focused lighting-control application. Its 3 x 3 mm UFBGA package is attractive for compact lamps and modules, while the 20 MHz clock supports responsive control updates. However, two PWM outputs limit multi-channel dimming, and the 2 KB Flash and 128-byte SRAM require concise firmware.
Is ATTINY24A-CCU in stock and how do I check its availability?
Current component availability should be checked through the Request a Quote form on this page, where the exact ATTINY24A-CCU ordering code can be submitted for confirmation. The manufacturer product entry identifies the ATtiny24A family as active, but project-specific stock, lot availability, and delivery timing require a current quotation. Provide the required quantity, package form, and target date with the request.
What is the price of ATTINY24A-CCU?
Use the Request a Quote form on this page for a current ATTINY24A-CCU quotation. The form allows buyers to specify quantity, desired package shipment form, production schedule, and inspection requirements so the commercial response reflects the actual order. Price and inventory can change with market conditions, quantity, and lifecycle position, so a project-specific quote is more reliable than a static figure.
What is the lead time for ATTINY24A-CCU?
The ATTINY24A-CCU lead time should be confirmed through the Request a Quote form on this page using the required quantity and production date. Lead time can depend on available inventory, package shipment form, lot allocation, and whether the quantity is for prototype, qualification, or mass production. Include the scheduled first use and any inspection requirements in the request for a meaningful delivery response.
What is the best cross-brand equivalent for ATTINY24A-CCU?
No cross-brand equivalent is established for the ATTINY24A-CCU because a genuine replacement must retain the 15-UFBGA pin arrangement and closely match clock, memory, I/O, ADC, USI, supply voltage, and programming behavior. Microchip's cross-reference search can identify comparable parts, but it does not by itself prove drop-in compatibility. Use the manufacturer datasheet and validate the candidate's footprint, peripheral mapping, and firmware toolchain before substitution.

エンジニアリング参考データ: ATTINY24A-CCU — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose the ATTINY24A-CCU when the product needs a compact 3 x 3 mm controller with a 20 MHz AVR core, 2 KB of Flash, 128 bytes of SRAM and EEPROM, 12 I/O lines, ADC capability, USI, and two PWM channels. It is particularly suitable for small sensor interfaces, LED controllers, and simple actuator modules where board area is important. Do not select it when the firmware cannot fit within 2 KB or when the application requires substantial buffering in only 128 bytes of SRAM. The ATTINY24A-SSU is not a PCB substitute because it uses a different SOIC footprint, and the ATTINY24V-10SSUR is not a direct alternative because both its package and maximum clock differ. Before substituting any candidate, verify every pin, supply requirement, peripheral mapping, interrupt vector, fuse setting, and programming connection against the manufacturer documentation.

代替品との比較

パラメータ この製品
Package 15-UFBGA (3 x 3 mm)
Brand Microchip Technology
Architecture 8-bit AVR RISC
Maximum Clock Frequency 20 MHz
Flash Memory 2 KB
EEPROM Memory 128 bytes
SRAM 128 bytes
General-Purpose I/O 12 lines
PWM Channels 2
Operating Voltage 1.8 V to 5.5 V

主な差別化要因

  • Compact 20 MHz AVR implementation (vs ATTINY24V-10SSUR)
  • More compact package than the SOIC family option (vs ATTINY24A-SSU)
  • Broader clock-rate choice within the ATtiny24A family (vs ATTINY20-CCUR)

設計ノート

Treat the 15-UFBGA as a fine-pitch assembly design. Follow the manufacturer land pattern and solder-mask recommendations exactly, confirm the PCB pad dimensions against the current datasheet, and validate the stencil aperture and paste volume during process qualification. The 3 x 3 mm body provides little visual access, so consider X-ray inspection and plan for pin-1 orientation controls in the assembly documentation.

Place the required supply decoupling capacitors close to the device power pins and keep the return path short. The operating range of 1.8 V to 5.5 V does not remove the need to select capacitors with suitable DC-bias derating and temperature characteristics. If an ADC is used, separate or carefully partition analog and digital supply paths so switching activity on the main rail does not introduce unnecessary measurement error.

Do not confuse the -CCU 15-UFBGA ordering option with the -SSU 14-pin SOIC device. The packages do not share a PCB footprint. Also avoid designing around the full 2 KB Flash for features that are not required at startup; with 128 bytes of SRAM, large local arrays and deep buffered processing can cause stack or heap exhaustion. Review the exact fuse, clock, and memory map during firmware bring-up.

Keep the ISP programming interface accessible and route it away from switching nodes and high-current motor paths. Place sensitive ADC inputs away from clock edges, inductor fields, and fast digital return currents. For designs using USI, check line capacitance and pull-up requirements under the selected operating voltage. A short ground return and a continuous ground plane generally provide more reliable behavior than fragmented routing around the compact package.

コンプライアンス情報

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
鉛フリー
Unknown
ハロゲンフリー
Unknown
紛争鉱物
Unknown

The component is identified as an industrial-temperature ATtiny24A-family device, but specific environmental and material-compliance declarations were not identified for the exact ordering code.

データ検証日: 2026-11-14 — データはXAIPARTの部品エンジニアリングチームによって検証・管理されています

関連検索

attiny24a pinout attiny24a datasheet attiny24a ssu attiny24a mur attiny24a programming attiny24a ssur attiny24a ssnr ATTINY24A-CCU datasheet pdf ATTINY24A-CCU 15-UFBGA pinout ATTINY24A-CCU application circuit ATTINY24A-CCU equivalent ATTINY24A-CCU replacement ATTINY24A-CCU price ATTINY24A-CCU stock Microchip ATTINY24A-CCU

関連部品&用語

Microchip Technology ATTINY24A-CCU ATtiny24A AVR 8-bit microcontroller RISC architecture picoPower 20 MHz 2 KB Flash 128-byte EEPROM 128-byte SRAM 12 general-purpose I/O lines 8-bit timer/counter two PWM channels ADC USI 15-UFBGA UFBGA package family surface-mount package SMD in-system programming LED dimming controller industrial control module compact sensor interface
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示