CD4050BCN - Hex Non-Inverting CMOS Buffer | onsemi
部品番号: CD4050BCN ✓ 生産中CD4050BCN 概要
A CMOS logic buffer is a digital integrated circuit that reproduces its input signal at an output while providing gain and reducing the loading imposed on the driving circuit. The CD4050BC belongs to the CD4000 CMOS logic family, placing it in the hierarchy of CMOS logic, logic IC, and digital semiconductor. Unlike an open-collector buffer, its specified push-pull output uses both pull-up and pull-down output stages to produce a defined low or high voltage.
The principal features of the CD4050BCN are its six parallel non-inverting channels, one-bit signal handling, push-pull output stage, and single-supply operation. Each channel preserves the logical polarity of its input, allowing a buffer to be inserted without changing Boolean logic. The monolithic CMOS construction supports low quiescent power in many logic applications and combines high input impedance with a low-impedance output capable of driving subsequent digital stages.
Technical operation is based on complementary N-channel and P-channel enhancement-mode transistors. The two transistor types combine to create the input stage, output drive, and internal logic functions. Because the outputs are push-pull, a low output is actively pulled toward ground while a high output is actively pulled toward the positive supply. This architecture is appropriate for conventional CMOS logic rails and for interfaces where a buffered output must present a more defined drive condition to the next stage.
Typical uses include buffering control and status signals in digital systems, supporting multiple CMOS logic inputs, driving standard 4000-series logic, and isolating a sensitive digital source from downstream capacitance. The six-channel organization can also simplify designs that previously required multiple discrete buffers. Each buffered path retains non-inverting behavior, which is important when the original logic equation must remain unchanged.
Designers should verify the operating voltage, input and output timing limits, absolute maximum ratings, and temperature range against the manufacturer datasheet before using the device at a system rail. Decoupling should follow the manufacturer recommendation, and unused inputs must not be left floating. The 16-pin PDIP package is intended for through-hole PCB assembly rather than a surface-mount production flow.
This page organizes the CD4050BCN function, package information, verified alternatives, and practical selection considerations in one engineering-focused reference. It also distinguishes confirmed drop-in candidates from alternatives that use a different package, helping designers avoid replacement parts that require board changes.
ドロップイン代替品: CD4050BCN — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: CD4050BCN (同一形状・フットプリント) — 相違点: Bits per Element, Logic Type, Technology.
CD4050BE
✅ ドロップイン価格はお問い合わせください
データシートを見る →MC14050BCPG
✅ ドロップイン📋 参考代替品(カタログ未掲載)
CD4050BCN 最大定格&電気的特性
| Number of Elements | 6 elements |
| Bits per Element | 1 bit |
| Logic Type | Buffer, non-inverting |
| 出力タイプ | Push-pull |
| 出力数 | 6 outputs |
| Supply Voltage Count | 1 supply |
| Technology | Complementary MOS (CMOS) |
| トランジスタタイプ | N-channel and P-channel enhancement-mode MOSFETs |
| パッケージ | 16-pin PDIP |
| ピン数 | 16 pins |
| 実装タイプ | Through-hole |
CD4050BCN 16-pin pdip ピン配置ガイド
CD4050BCN (16-pin pdip パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: CD4050BCN.
詳細は データシート をご参照ください。
主な用途
CD4050BCN の用途: 6 件s: Digital Control-Signal Buffering, CMOS Logic Fan-Out Isolation, Single-Supply Logic-Level Conversion, Sequential Logic Control, Interface Between Logic Families, General-Purpose CMOS Signal Conditioning.
Digital Control-Signal Buffering
The CD4050BCN is suitable for buffering several digital control signals without changing their Boolean polarity. Its six channels provide one dedicated buffer path per bit, while the push-pull output stage produces a defined high or low state. Compared with driving a logic input directly from a high-impedance source, placing the device at the interface restores signal drive and isolates the source from downstream loading. For a control panel, for example, six buffered lines can carry enable, mode, reset, and status commands between circuit sections. The principal engineering checks are the chosen supply voltage, output current per channel, fan-out into the connected family, and whether the propagation delay is acceptable for the control timing.
おすすめ
CMOS Logic Fan-Out Isolation
The CD4050BCN can isolate a sensitive logic source from the capacitance presented by connected CMOS loads. Each of its six channels accepts a one-bit input and presents a push-pull output that does not invert the logic. This arrangement is useful when a generated or latched control signal must reach multiple 4000-series inputs without loading the original driver. The buffer’s six-channel structure allows several isolated paths to be implemented in one 16-pin PDIP package. Designers should determine the total input current drawn by the loads, compare it with the output-current rating in the manufacturer datasheet, and confirm that the added propagation delay remains compatible with the system timing.
おすすめ
Single-Supply Logic-Level Conversion
The CD4050BCN supports logic-level conversion using a single supply voltage, as identified in the manufacturer datasheet. This makes its non-inverting channels useful when a signal must be shifted into the voltage domain recognized by a compatible CMOS load. Unlike a dual-supply interface circuit, the device operates from one VDD rail and shares the same supply reference. The level-conversion behavior still requires careful threshold analysis: the input voltage must cross the receiving device’s switching threshold, and the output high and low levels must meet the load’s requirements. Check supply limits, input thresholds, output levels, and timing rather than assuming that every signal amplitude can be converted automatically.
おすすめ
Sequential Logic Control
The CD4050BCN can provide buffered, non-inverting control paths for a sequential logic block built from CMOS gates. Six channels make it practical to distribute clock-enable, reset, mode-select, and state-transition commands while preserving their active logic levels. A push-pull output is particularly useful when the control lines must present a consistent state across several connected logic inputs. Place the buffer close to the receiving logic when trace capacitance or shared-bus loading is significant. Verify the delay introduced by the buffer against the available timing margin, and ensure that the power rail can support all six outputs simultaneously when several control lines change at the same time.
おすすめ
Interface Between Logic Families
The CD4050BCN can serve as a bridge between a compatible CMOS signal source and a load that requires buffered non-inverting drive. The CD4050BC datasheet describes logic-level conversion using one supply voltage, while the six push-pull channels provide defined output states. A practical interface may use the device when the receiving logic cannot be driven reliably from a weak or high-impedance source. The buffer cannot arbitrarily translate incompatible voltage standards, so the engineer must verify that the input thresholds, output levels, supply range, and timing of both devices overlap. This makes the part suitable for compatible CMOS logic, but not for unrestricted conversion between unrelated voltage domains.
おすすめ
General-Purpose CMOS Signal Conditioning
The CD4050BCN provides a straightforward way to condition digital signals in mixed analog and control systems. Its non-inverting channels can buffer comparator, latch, or counter outputs before they reach another logic block, reducing sensitivity to input loading. The monolithic CMOS implementation combines N-channel and P-channel enhancement-mode transistors, while the push-pull output stage supports repeatable logic states. Because the device contains six channels, a board can allocate them to separate alarms, interlocks, mode commands, or acknowledgment signals rather than adding several discrete packages. The design review should include the allowable input levels, output drive, propagation delay, power consumption, and the requirement that every unused CMOS input be connected to a defined state.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: CD4050BCN — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | CD4050BE | MC14050BCPG |
|---|---|---|---|
| Package | 16-pin PDIP | DIP-16 | DIP-16 |
| Brand | onsemi | Texas Instruments | NXP |
| Logic Function | Hex non-inverting buffer | Hex non-inverting buffer | Hex non-inverting buffer |
| Number of Elements | 6 elements | 6 elements | 6 elements |
| Bits per Element | 1 bit | 1 bit | 1 bit |
| Mounting Type | Through-hole | Through-hole | Through-hole |
主な差別化要因
- Six dedicated non-inverting channels in one through-hole package (vs CD4050BE)
- Push-pull output specification (vs MC14050BCPG)
- Single-supply level-conversion function (vs CD4050BE)
設計ノート
Treat all 16 package leads according to the manufacturer pin-assignment table, including supply and ground identification. Place the device so that every input has a defined logic state; unused CMOS inputs must be tied to a valid rail rather than left floating. Because the CD4050BCN uses a 16-pin PDIP package, confirm that the PCB has the correct through-hole footprint, pin spacing, and drill pattern before releasing a board layout.
Confirm the complete VDD range, quiescent current, and output-current limits against the manufacturer datasheet. If multiple channels can switch simultaneously, size the supply trace and bypass capacitor for the combined dynamic current rather than a single steady output. The device performs logic-level conversion using one supply, so the chosen VDD must also satisfy the input thresholds and output-level requirements of every connected CMOS load.
Check propagation delay, output rise and fall behavior, and the capacitive load permitted for each channel before using the buffer in a timing-sensitive path. The push-pull output provides a more defined drive than an open-drain output, but long PCB traces or simultaneous output switching can still affect signal integrity. Keep sensitive routed away from the supply entry and output paths when the surrounding system contains fast-switching circuitry.
コンプライアンス情報
No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified in the product listings. AEC-Q100 is not applicable because the CD4050BCN is a general-purpose logic IC rather than an automotive-qualified device.