onsemi

MC14521BF - 24-Stage Binary Frequency Divider | onsemi

部品番号: MC14521BF ✗ 生産終了
16-pin PDIP Package External oscillator input buffer Speed
MOQ: 1 |

MC14521BF 概要

onsemi MC14521BF is a 24-stage binary frequency divider and counter IC with a 16-pin PDIP package. Its internal architecture contains 24 flip-flops, each dividing the frequency of the preceding stage by two, allowing the device to count through 2^24 states, or 16,777,216. The input circuit supports three operating modes: crystal oscillator, RC oscillator, and buffered external-oscillator input.

A binary frequency divider is a sequential logic device that reduces an input clock frequency by a fixed integer factor. The MC14521B belongs to the counter and multivibrator family of CMOS logic ICs, placing it within the broader semiconductor hierarchy of sequential logic, counters, frequency dividers, and clock-management circuits. Unlike a programmable divider or phase-locked loop, it implements a fixed divide-by-2^24 ratio at its output while retaining a simple external clocking architecture.

The principal feature of the MC14521BF is its 24-stage flip-flop chain. Each successive stage operates at one-half the frequency of the preceding stage, enabling a clock input to be divided into a substantially lower-frequency output. The manufacturer describes three input configurations: a crystal oscillator, an RC oscillator, or an input buffer for an externally supplied oscillator. These configurations give designers flexibility when creating stable timing references or dividing an existing system clock.

The internal counting architecture advances on each active clock transition. The 24-bit count range reaches 16,777,216, which makes the device useful for long timing intervals, fixed-ratio clock generation, event counting, and low-frequency timing references. Its fixed binary ratio differs from general-purpose programmable counters and makes system timing easier to analyze when a known divide factor is required.

Typical uses include timer and delay networks, pulse-rate reduction, instrumentation clocks, sequential test systems, low-frequency waveform generation, and digital timing references. In an RC or crystal-oscillator implementation, the device can establish its own timing source; with the buffered external-oscillator mode, it can instead divide a clock already present elsewhere in the system.

Designers should select the appropriate oscillator components and confirm the device’s electrical limits, supply requirements, and timing characteristics against the manufacturer datasheet before implementation. PCB layout should keep oscillator and timing paths compact, maintain a defined ground reference, and separate sensitive timing nodes from noisy switching circuits. The 16-pin PDIP package is suitable for through-hole assembly and prototype or legacy industrial equipment where a large package is acceptable.

This page combines the manufacturer function description, package and pin-count information, architecture details, application guidance, and a transparent assessment of drop-in replacement options. It also distinguishes the uniquely ordered MC14521BF ordering code from generic family references and focuses design decisions on the fixed 24-stage division behavior.

ドロップイン代替品: MC14521BF — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

このシリーズのバリエーション

同一シリーズでドロップイン互換のモデル: MC14521BF (同一形状・フットプリント) — 相違点: Logic Family, Package.

onsemi
Logic Family: CMOS
Package: 16-pin SOIC
比較対象 MC14521BF →

MC14521BE

✅ ドロップイン ⚠️ 仕様未検証
📦 16-pin SOIC (package code E)
MC14521BE differs from MC14521BF by ordering-code temperature grade, while retaining the 24-stage divider function; the exact grade and package marking must be confirmed against the onsemi datasheet.

📋 参考代替品(カタログ未掲載)

MC14521BD

✅ ドロップイン ⚠️ 仕様未検証
onsemi
📦 16-pin SOIC (package code D)
24-stage CMOS frequency divider · 24 flip-flops · 16,777,216 counts (2^24) · 2:1 · 1 element · Negative edge · 3 modes: crystal, RC, or external-oscillator input · 5 V

価格はお問い合わせください

データシートを見る →

MC14521BM

✅ ドロップイン ⚠️ 仕様未検証
📦 16-pin SOIC (package code M)
MC14521BM uses the same 16-pin SOIC footprint and 24-stage divide-by-two core, with ordering-code grade differences; verify its temperature range and operating limits in the manufacturer documentation.

📋 参考代替品(カタログ未掲載)

MC14521BFL

✅ ドロップイン ⚠️ 仕様未検証
📦 16-pin SOIC (package code FL)
MC14521BFL uses the same MC14521B 24-stage divider core in a 16-pin SOIC outline, with the FL ordering code potentially identifying a different grade or qualification class that must be checked.

📋 参考代替品(カタログ未掲載)

MC14521BAL

✅ ドロップイン ⚠️ 仕様未検証
📦 16-pin SOIC (package code AL)
MC14521BAL retains the 24-stage frequency-divider core and 16-pin SOIC footprint while adding an ordering-code qualification difference; confirm pinout and grade details before use.

📋 参考代替品(カタログ未掲載)

MC14521BF 最大定格&電気的特性

Product Type 24-stage frequency divider and counter IC
Number of Flip-Flops 24 stages
Total Division Ratio 2^24 (16,777,216:1)
Division Per Stage 2:1
Counter States 16,777,216 states
Operating Modes 3 modes
Crystal Oscillator Mode Supported
RC Oscillator Mode Supported
External Oscillator Buffer Mode Supported
Logic Family MC14521B CMOS counter and frequency-divider family
パッケージ 16-pin PDIP
ピン数 16 pins
Terminal Type 16 through-hole terminals
実装スタイル Through-hole PDIP
Output Function Divided clock output
Clock Input Function External oscillator input buffer
Count Advance On each active clock transition

MC14521BF 16-pin pdip ピン配置ガイド

MC14521BF (16-pin pdip パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。

MC14521BF の 16-pin pdip パッケージピン配置図

詳細なピン配置データはありません: MC14521BF.

詳細は データシート をご参照ください。

主な用途

MC14521BF の用途: 6 件s: Long-Duration Timer Reference, External Clock Frequency Reduction, RC-Oscillator Timing Network, Crystal-Based Low-Frequency Reference, Pulse and Event Rate Reduction, Instrumentation and Test-System Clocking.

⏱️

Long-Duration Timer Reference

The MC14521BF is useful when a system requires a slow timing reference derived from a much faster clock. Its 24 flip-flops divide the source by 2^24, producing a fixed 16,777,216:1 relationship that can extend a short oscillator period into a long counting interval. Place the device in a protected low-noise clock section, route the reference away from switching nodes, and account for propagation delay accumulated through the 24-stage chain when sequencing multiple events.

🌐

External Clock Frequency Reduction

The buffered external-oscillator mode allows MC14521BF to divide a master clock already distributed by another timing circuit. Because every one of its 24 stages divides by two, the device produces an extremely low-frequency derived clock from a stable high-frequency source. This arrangement is useful in instrumentation and control systems that need repeatable pulse pacing. Confirm input amplitude and frequency against the manufacturer limits, and keep the clock path short to minimize added jitter and noise susceptibility.

🔧

RC-Oscillator Timing Network

MC14521BF can establish a self-contained timing reference by operating as an RC oscillator, avoiding a separate master clock and the associated distribution network. Its 24-stage binary division then reduces that reference to a slow output suitable for supervisory timing or repetitive event generation. Select the RC network using the oscillator guidance in the onsemi MC14521B manufacturer datasheet, because component tolerance, temperature behavior, and loading influence the effective time base.

📡

Crystal-Based Low-Frequency Reference

The crystal-oscillator mode lets MC14521BF operate from a crystal-based timing reference when a stable low-frequency output is required without relying on an external oscillator buffer. The 24 flip-flops divide the established frequency by 2^24, creating a very slow clock or event cadence. Preserve a clean ground reference, place the oscillator network close to the device, and follow the manufacturer’s grounding and layout recommendations to reduce pickup and startup sensitivity.

📊

Pulse and Event Rate Reduction

When an input pulse stream is too fast for useful downstream counting, MC14521BF reduces its effective rate by the fixed 2^24 factor. The resulting slow cadence can pace indicator updates, supervisory actions, or test-system events while preserving the original clock’s frequency relationship. Treat the divider as a fixed-ratio functional block rather than a programmable prescaler, and verify the cumulative propagation delay and output behavior against the system timing budget.

🖥️

Instrumentation and Test-System Clocking

MC14521BF can derive a predictable slow timing reference for instrumentation, automated test equipment, and legacy industrial controllers. The internal 24-stage chain provides a large fixed division without requiring a bank of external counters. In such systems, isolate the oscillator and output paths from relays, power stages, and high-current switching equipment. A separate general-purpose timer can provide programmable or shorter intervals where the fixed 16,777,216:1 division is not appropriate.

What is the onsemi MC14521BF?
The onsemi MC14521BF is a 24-stage binary frequency divider and counter IC in a 16-pin PDIP package. According to the onsemi MC14521B manufacturer datasheet, it contains a chain of 24 flip-flops, with each stage dividing the preceding frequency by two. Its input circuit can operate as a crystal oscillator, an RC oscillator, or a buffer for an external oscillator.
What is the total division ratio of MC14521BF?
The MC14521BF has a total division ratio of 2^24, equivalent to 16,777,216:1. According to the onsemi MC14521B manufacturer datasheet, each of the 24 flip-flops divides the frequency of the previous stage by two. The resulting long division interval makes the device useful for fixed-ratio clock reduction, event counting, delay generation, and long-period timing references.
What are the three operating modes of MC14521BF?
The MC14521BF supports crystal-oscillator, RC-oscillator, and buffered external-oscillator operation. According to the onsemi MC14521B manufacturer datasheet, the input circuit can establish an internal timing reference with a crystal or RC network or act as an input buffer when the system already supplies an external oscillator. This flexibility allows the same divider to support standalone and system-synchronized timing designs.
Where can I download the MC14521BF datasheet PDF?
The official MC14521BF datasheet PDF is available from onsemi at https://www.onsemi.com/pdf/datasheet/mc14521b-d.pdf. The document is titled for the MC14521B family and describes the 24-stage divider architecture, three input operating modes, counter behavior, electrical characteristics, and package information. Use the manufacturer document for authoritative supply-voltage, timing, environmental, and pin-level design decisions.
Where can I find the MC14521BF pinout?
The MC14521BF pinout should be taken from the pin-description table and package drawing in the onsemi MC14521B manufacturer datasheet. The component is identified as a 16-pin PDIP device, but individual pin numbers and functions are not reproduced on this page to avoid transcribing them incorrectly. Use the manufacturer drawing when assigning PCB nets, and preserve all supply and ground connections shown there.
How does the MC14521BF frequency division work?
The MC14521BF divides the clock signal progressively through 24 flip-flops, with every stage operating at one-half the frequency of the preceding stage. According to the onsemi MC14521B manufacturer datasheet, the count advances on the active clock transition. Repeated division by two produces the fixed 2^24 ratio, or 16,777,216:1, between the internal timing reference and the divided output.
Can MC14521BF use an external oscillator?
Yes, the MC14521BF can use an external oscillator through its buffered external-oscillator input mode. According to the onsemi MC14521B manufacturer datasheet, the input circuit functions as an input buffer when an external oscillator is used. This mode is useful when a master system clock already exists and must be divided without introducing a separate RC or crystal timing network.
Can MC14521BF operate as an RC oscillator?
Yes, the MC14521BF includes an RC-oscillator operating mode. According to the onsemi MC14521B manufacturer datasheet, its input circuit can operate as an RC oscillator as well as a crystal oscillator or external-oscillator buffer. Component selection and timing accuracy must be based on the manufacturer oscillator equations and electrical characteristics, especially when the divider must maintain a predictable long-term time base.
When should I choose MC14521BF over a general-purpose counter?
Choose MC14521BF when the design needs a fixed divide-by-2^24 clock reduction or a long 16,777,216-count interval rather than programmable counting. According to the onsemi MC14521B manufacturer datasheet, its dedicated 24-stage divider and three oscillator modes simplify fixed-ratio timing. A general-purpose counter may be preferable when the ratio must be selected or changed dynamically.
Is MC14521BF suitable for event counting and long timing intervals?
Yes, the MC14521BF is suitable for event counting and long timing intervals because it advances through a 24-stage counter chain. According to the onsemi MC14521B manufacturer datasheet, the count reaches 2^24, or 16,777,216. It is particularly useful when an input event rate must be reduced to a slow cadence that can drive another timer, display, or control function.
What is the best drop-in replacement for MC14521BF?
No verified drop-in replacement for MC14521BF was established because the cross-reference results did not identify a candidate with the same 16-pin PDIP footprint, 24-stage division ratio, and oscillator-mode pinout. According to the onsemi MC14521B manufacturer datasheet, preserving the complete 24-stage architecture and terminal assignments is essential, so a functionally similar frequency divider should not be treated as a drop-in substitute without pin-by-pin validation.
Is there an onsemi equivalent to MC14521BF?
The onsemi MC14521B is the documented family associated with MC14521BF, but the ordering-code and package suffixes must still be checked before substitution. According to the onsemi MC14521B manufacturer datasheet, the device requires a 16-terminal package implementation and the same 24-stage divider function. The suffix associated with a particular package, temperature grade, or shipping configuration must not be treated as interchangeable without the manufacturer ordering information.
What onsemi equivalent should I use if MC14521BF becomes unavailable?
Request an availability and compatibility review through the Request a Quote form on this page when MC14521BF cannot be sourced. No onsemi part was confirmed as a pin-compatible 16-pin PDIP substitute, so assigning an equivalent requires the original manufacturer ordering table and a complete pinout comparison. Package size, terminal numbering, supply pins, oscillator connections, and output behavior must all match.
What is the lead time and stock status for MC14521BF?
Use the Request a Quote form on this page for the current MC14521BF stock status, minimum order quantity, and lead time. The available product listings do not provide a reliable quantity-break table or a manufacturer commitment for current availability. The component’s lifecycle status is also not explicitly stated in the product information, so it should not be assumed to be active, obsolete, or last-time-buy.
Where can I buy MC14521BF and check its price?
Use the Request a Quote form on this page to request MC14521BF pricing, current availability, and lead time. The retrieved listings do not contain explicit quantity-break prices for the exact ordering code, so no static unit price is presented. This approach also allows the requested package, quantity, and shipment destination to be evaluated together before an order is placed.
What are the key specifications of MC14521BF that engineers should know?
The key MC14521BF specifications are its 24-stage flip-flop architecture, 2^24 total division ratio, 16,777,216 counter states, three operating modes, and 16-pin PDIP package. According to the onsemi MC14521B manufacturer datasheet, each stage divides frequency by two, and the input can operate as a crystal oscillator, RC oscillator, or external-oscillator buffer. Confirm electrical limits and timing values directly in the manufacturer document.
Is MC14521BF RoHS and REACH compliant?
The RoHS and REACH status of MC14521BF is not explicitly stated in the retrieved manufacturer page or datasheet excerpts. Check the current onsemi product documentation and material-compliance records before treating the component as compliant for a regulated design. Lead-free, halogen-free, and conflict-minerals status should likewise remain unconfirmed until documented by the manufacturer or an applicable certification record.

エンジニアリング参考データ: MC14521BF — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose MC14521BF when the design specifically needs a fixed 24-stage binary divider with a 2^24 division ratio and three selectable timing modes: crystal oscillator, RC oscillator, or buffered external oscillator. Its 24-stage architecture is particularly useful for long counting intervals, slow event pacing, and low-frequency references. It is less appropriate when the division ratio must be programmable, when a much shorter timer interval is needed, or when a modern small-footprint package is required. No drop-in alternative was confirmed because the available cross-reference results did not establish a part with the same 16-pin PDIP footprint, terminal arrangement, and 24-stage functionality. Treat the family-level MC14521B name as a device description rather than automatic proof that every package, temperature, or ordering suffix is interchangeable. For a redesign, validate the complete pinout, oscillator components, output timing, supply requirements, and environmental constraints before approving a substitute.

設計ノート

Keep the oscillator components, timing pins, and divided output routing compact and away from high-current switching paths. A crystal or RC network is sensitive to parasitic capacitance, ground bounce, and radiated noise, while the external-oscillator mode can pick up jitter from a poorly controlled clock source. Use a continuous ground plane, short return paths, and a quiet placement area where the 16-pin PDIP package remains accessible for prototype rework.

Do not assume that the divided output preserves the input waveform shape. The device contains 24 sequential flip-flops, so propagation delay, transition behavior, and accumulated timing uncertainty across the chain determine the usable output waveform. Preserve clean edge transitions at the selected operating frequency, observe the manufacturer’s input and output timing limits, and leave suitable logic margin for any receiving circuit that must reliably detect each divided transition.

Avoid treating MC14521BF as a programmable counter or as a 24-bit programmable divider. Its division ratio is fixed at 2^24, or 16,777,216:1, and its ordering code identifies a specific 16-pin PDIP implementation. A substitute is only drop-in when its package, terminal numbering, power pins, oscillator connections, count sequence, and output behavior match; verify every function in the manufacturer pin table before approving a replacement.

コンプライアンス情報

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
鉛フリー
Unknown
ハロゲンフリー
Unknown
紛争鉱物
Unknown

No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement appears in the retrieved manufacturer and distributor information. These statuses require confirmation from current onsemi documentation.

関連検索

MC14521BF datasheet MC14521BF datasheet pdf MC14521BF pinout MC14521BF equivalent MC14521BF replacement MC14521BF cross reference onsemi MC14521BF MC14521BF 24 stage divider MC14521BF PDIP-16 MC14521BF frequency divider MC14521BF oscillator circuit MC14521BF price MC14521BF stock MC14521BF counter IC

関連部品&用語

onsemi MC14521BF MC14521B 24-stage frequency divider binary counter CMOS logic IC sequential logic clock divider frequency division division ratio 2^24 16,777,216 counter states crystal oscillator mode RC oscillator mode external oscillator input buffer flip-flop chain 16-pin PDIP through-hole package oscillator timing network logic IC counter and multivibrator MC74F538N CS82C54-12 MC74F243M fixed-ratio clocking
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示