CD4053BCM - Triple 2:1 240Ω Analog Switch | onsemi
部品番号: CD4053BCM ✓ 生産中CD4053BCM 概要
An analog multiplexer is a semiconductor switch that connects one of several analog inputs to a common output. The broader hierarchy is analog multiplexer or demultiplexer → analog switch → interface IC → semiconductor. A multiplexer combines signals onto one path, while a demultiplexer separates a shared path into multiple destinations. The CD4053BCM implements both functions through three 2:1 switch sections sharing the same address and inhibit controls.
The principal verified features are three switch circuits, a 2:1 configuration, 240 Ω ON resistance, a 16-SOIC package, and CMOS operation. Control inputs A, B, and C select the active route, while INHIBIT provides a common shutdown or isolation function. The manufacturer documentation also identifies low ON impedance and very low OFF leakage current. Typical electrical characteristics are tabulated from −55 °C through 125 °C, supporting industrial and extended-temperature designs.
The CD4053BCM is suited to signals that remain within the device’s supply and analog signal limits. Because the control inputs are digital while the switched paths are analog, the address logic may operate from the same supply rails when their voltage thresholds are compatible with the system. Input protection and signal-level behavior depend on the exact supply configuration, so the electrical characteristic tables should be checked for each channel state and operating condition.
Typical uses include sensor selection, instrumentation routing, signal multiplexing in test systems, audio channel selection, and general analog signal switching. Three independent 2:1 sections are particularly useful when several paired signals must be selected together. For example, a controller can route differential sensor outputs, alternate measurement paths, or share a converter input among several sources without changing the surrounding board layout.
PCB implementation should preserve short analog traces, use a continuous ground plane, and keep switching nodes compact to reduce coupling and parasitic capacitance. Avoid routing high-impedance or sensitive signals directly beside the address and inhibit traces. Decoupling capacitors should be placed close to the supply pins, while unused control inputs must be tied to a defined logic level rather than left floating.
This page organizes the verified electrical characteristics, pin information, drop-in alternatives, application guidance, and design considerations into one engineering reference. It also identifies which parameters require confirmation before substitution or redesign, helping engineers shorten component selection and PCB-review time.
ドロップイン代替品: CD4053BCM — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
CD74HC4053M
✅ ドロップイン📋 参考代替品(カタログ未掲載)
CD74HC4053PWR
✅ ドロップイン📋 参考代替品(カタログ未掲載)
CD74HC4053
✅ ドロップイン📋 参考代替品(カタログ未掲載)
SN74LV4053A
✅ ドロップイン📋 参考代替品(カタログ未掲載)
CD4053BMG4
✅ ドロップイン📋 参考代替品(カタログ未掲載)
CD4053BCM 最大定格&電気的特性
| Switch Circuit Count | 3 circuits |
| Multiplexer Configuration | 2:1 per circuit |
| ON Resistance | 240 Ω |
| Technology | CMOS |
| パッケージ | 16-SOIC |
| ピン数 | 16 pins |
| 実装タイプ | Surface mount |
| Select Inputs | A, B, and C |
| Control Inputs | A, B, C, and INHIBIT |
| Characteristic Temperature Points | −55 °C, 25 °C, and 125 °C |
| Supply Configuration | VDD, VSS, and VEE rails |
| Control Input Test Condition | VDD = 5 V |
| Control Input Load Condition | RL = 1 kΩ to VSS |
CD4053BCM 16-soic ピン配置ガイド
CD4053BCM (16-soic パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: CD4053BCM.
詳細は データシート をご参照ください。
主な用途
CD4053BCM の用途: 6 件s: Multiplexed Sensor Measurement, Instrumentation Signal Routing, Audio Channel Selection, Test-System Signal Multiplexing, Data Acquisition Front Ends, Battery-Powered Analog Systems.
Multiplexed Sensor Measurement
The CD4053BCM fits sensor-selection circuits that must route several measured signals to a shared amplifier or converter. Its three 2:1 sections can select three signal pairs, while the common address inputs keep the channels synchronized. The documented 240 Ω ON resistance gives designers a concrete impedance value to include in sensor settling and amplifier-input calculations. Because the device also provides very low OFF leakage, disabled channels can contribute less unwanted interaction with high-impedance sensors. Confirm the permitted signal range against the supply configuration and verify whether the source impedance requires a separate buffer.
おすすめ
Instrumentation Signal Routing
The CD4053BCM is appropriate for laboratory and industrial instrumentation that selects among several measurement paths without changing connectors or using multiple discrete relays. Three independently addressed 2:1 switch sections simplify routing of paired excitation and return signals. The 240 Ω ON resistance must be included in source-load calculations, particularly for high-impedance sensors and long cable runs. Its low OFF leakage characteristic helps reduce crosstalk between disabled paths. Layout should keep sensitive routes away from address and inhibit traces, while supply bypassing should be placed directly between the device power terminals.
おすすめ
Audio Channel Selection
The CD4053BCM can select audio or communications paths when the source impedance is low enough for the 240 Ω ON resistance to preserve signal amplitude. The three 2:1 sections support compact routing of related left/right or input/output pairs in analog equipment. Its very low OFF leakage helps maintain isolation between unselected sources, although common-mode range, distortion, and switching transients remain important considerations. Use short PCB traces, a continuous return plane, and decoupled supply pins to prevent digital control activity from coupling into the audio path. Verify the actual signal swing before operation.
おすすめ
Test-System Signal Multiplexing
The CD4053BCM is useful in automated test equipment that routes a shared source, instrument input, or stimulus across several circuit nodes. Its three 2:1 sections provide compact channel selection while the inhibit function supports isolation during test sequencing. Engineers can use the 240 Ω ON resistance when defining measurement accuracy and output-loading budgets. Care is required if the multiplexer switches near large transients, because supply bounce and control-edge coupling can disturb high-impedance measurements. Add local supply bypassing and avoid placing multiplexed analog traces beside digital address lines.
おすすめ
Data Acquisition Front Ends
The CD4053BCM can front a data-acquisition system by selecting which analog source reaches a common converter input. Three 2:1 sections make it practical to multiplex grouped channels while retaining one compact package and one set of address controls. The 240 Ω ON resistance should be checked against the converter’s acquisition time and the source impedance, because excessive loading can reduce settling accuracy. The device’s very low OFF leakage is beneficial when unused sources have high DC impedance. A grounded plane, short switched traces, and closely placed supply decoupling provide a stable return path and reduce digital coupling.
おすすめ
Battery-Powered Analog Systems
The CD4053BCM can reduce routing complexity in low-power analog systems by replacing several discrete switches with one CMOS multiplexer. Its three 2:1 sections support compact signal selection in portable instruments, condition-monitoring nodes, and compact sensor interfaces. Low OFF leakage is valuable when the selected source has a high impedance, while the 240 Ω ON resistance must remain compatible with the load. Supply current, switching speed, and permissible input swing should be reviewed for the actual operating mode. The INHIBIT control can also support isolation when the system needs a defined inactive state.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: CD4053BCM — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | CD74HC4053M | CD74HC4053PWR | CD74HC4053 | SN74LV4053A | CD4053BMG4 |
|---|---|---|---|---|---|---|
| Brand | onsemi | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Fairchild Semiconductor |
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Pin Count | 16 pins | 16 pins | 16 pins | 16 pins | 16 pins | 16 pins |
| Multiplexer Configuration | Triple 2:1 | Triple 2:1 | Triple 2:1 | Triple 2:1 | Triple 2:1 | Triple 2:1 |
| Technology | CMOS | Silicon-gate CMOS | Silicon-gate CMOS | CMOS | Low-voltage CMOS | CMOS |
| Control Inputs | A, B, C, and INHIBIT | Select and inhibit controls | Select and inhibit controls | Select and inhibit controls | Select and inhibit controls | A, B, C, and INHIBIT |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount |
主な差別化要因
- Documented channel resistance (vs CD74HC4053M)
- Matched 16-terminal footprint (vs CD74HC4053PWR)
- Extended-temperature characterization (vs SN74LV4053A)
設計ノート
Route the three analog switch sections symmetrically and keep each common terminal close to its associated switched terminal. Place the INHIBIT and A/B/C traces away from sensitive analog paths, and terminate unused control inputs at a defined logic level. A continuous ground plane provides a low-impedance return for switching transients, while short traces reduce parasitic capacitance that can slow settling after an address change.
Connect the supply terminals according to the manufacturer’s recommended configuration and place the local bypass capacitor directly beside the power pins. Avoid adding large bulk capacitance directly across the switched analog nodes unless the application requires it, since excessive node capacitance increases settling time after a selection change. Validate signal swing, supply voltage, and logic thresholds together to ensure every addressed state remains inside the rated operating region.
Do not treat the 240 Ω ON resistance as suitable for every source impedance. A high-impedance sensor may require a buffer, and a long cable may require lower channel resistance or a different switch architecture. Also avoid leaving A, B, C, or INHIBIT floating. For each design, review the pin-description and DC electrical tables together because package matching alone does not establish logic-level or analog-range compatibility.
Keep switching transients away from reference, clock, and high-gain analog nodes. If the source impedance is high, the device’s OFF leakage and PCB contamination can influence node voltage, so protective guarding and clean assembly practices may matter. For fast settling requirements, measure the complete address-transition waveform with the intended source and load because the on-resistance alone does not determine channel settling time.
コンプライアンス情報
RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not established by the referenced documentation excerpts. AEC-Q100 qualification is not applicable to this general-purpose interface IC.