DS90CR281MTD - 28-Bit LVDS Channel Link Transmitter | TI
部品番号: DS90CR281MTD ✓ 生産中DS90CR281MTD 概要
What is a Channel Link transmitter? A Channel Link transmitter is a parallel-to-differential interface IC that serializes or multiplexes multiple low-voltage digital signals onto fewer differential pairs. LVDS, or Low Voltage Differential Signaling, is a high-speed electrical interface that uses the voltage difference between two conductors to improve noise immunity and reduce cable size. In the DS90CR281MTD, 28 CMOS/TTL bits and the clock are carried over four LVDS data streams plus a transmitted clock pair.
Key features include 28-bit parallel data input, four LVDS output streams, LVDS protocol support, and operation from a 4.5 V to 5.5 V supply. The multiplexing arrangement reduces the conductor count required for a wide parallel bus. This is particularly useful when a system must move data between circuit boards, across a cable, or between a parallel processing subsystem and a high-speed communications section while maintaining differential-signal integrity.
The DS90CR281MTD uses a phase-locked transmit clock that is transmitted with the data. This arrangement allows the receiving equipment to recover the associated data timing from the differential interface rather than relying on a separate single-ended clock conductor. The receiver must support the corresponding Channel Link data format and LVDS signaling levels, so cable length, connector geometry, termination, and receiver capability remain important system-level considerations.
Typical applications include industrial control and data acquisition systems, instrumentation, test and measurement equipment, high-speed backplanes, industrial networking, and embedded systems that transfer wide parallel data over a cable. The 56-pin TSSOP package is suitable for surface-mount assembly, although the device requires careful routing of the high-speed differential outputs and a stable supply-decoupling network.
For PCB implementation, place the device close to the source logic, route LVDS pairs as controlled-impedance differential nets, and keep the input and output return paths short. Verify the receiver’s input capacitance, cable length, connector loss, and termination strategy before release. The manufacturer datasheet and the TI DS90CR281 product page are the appropriate references for pin assignment, timing, electrical characteristics, and application details.
ドロップイン代替品: DS90CR281MTD — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: DS90CR281MTD (同一形状・フットプリント) — 相違点: Package, Product Type.
DS90CR285MTD
✅ ドロップイン価格はお問い合わせください
データシートを見る →DS90CR281MTD 仕様
| Product Type | 28-Bit Channel Link Transmitter |
| Data Input Width | 28 bits |
| LVDS Output Streams | 4 |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Protocol | LVDS |
| Logic Input Type | CMOS/TTL |
| Transmitter Type | Transmitter |
| パッケージ | 56-TSSOP (0.240, 6.10 mm width) |
| Number of Terminals | 56 |
| 実装タイプ | Surface Mount |
| Package Shape | Rectangular |
| Terminal Form | Gull Wing |
| Temperature Grade | Commercial |
| Packaging | Tube |
| Transmitted Clock | Yes; phase-locked transmit clock |
| Differential Output Data Pairs | 4 data pairs plus 1 clock pair |
DS90CR281MTD rectangular ピン配置ガイド
DS90CR281MTD (rectangular パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: DS90CR281MTD.
詳細は データシート をご参照ください。
主な用途
DS90CR281MTD の用途: 6 件s: Industrial Data Acquisition, Test and Measurement Instrumentation, Industrial Networking, High-Speed Backplanes, Embedded Parallel Data Systems, Data Acquisition Cards.
Industrial Data Acquisition
The DS90CR281MTD is suitable for industrial data-acquisition systems that collect a wide parallel data set and transfer it to a remote processing or storage section. Its 28 CMOS/TTL input bits are converted into four LVDS data streams, reducing the number of conductors required across a cable or board-to-board link. The transmitted phase-locked clock supports timing recovery at the receiver. Use a receiver with compatible LVDS thresholds and verify cable length, data rate, grounding, and industrial environmental requirements.
おすすめ
Test and Measurement Instrumentation
The DS90CR281MTD can connect a wide parallel measurement or control bus to a high-speed instrument chassis through balanced LVDS links. Four differential data streams carry the 28-bit payload more compactly than 28 single-ended conductors, while the transmitted clock provides the receiver with a timing reference. The design must account for connector loss, cable length, receiver bandwidth, termination, and the 4.5 V to 5.5 V supply requirement of the transmitter.
おすすめ
Industrial Networking
DS90CR281MTD is applicable to industrial network equipment that needs a compact differential connection between parallel processing logic and a communications or line-card module. LVDS helps maintain signal integrity over a balanced cable by rejecting common-mode noise and reducing the conductor count of the link. The implementation should be validated for the intended data rate, receiver capability, cable impedance, connector geometry, and the separation between switching circuitry and the differential pairs.
おすすめ
High-Speed Backplanes
The DS90CR281MTD can be used in a backplane or mezzanine interface where a 28-bit parallel bus must cross a connector or cable assembly. Multiplexing the bus into four LVDS data streams reduces pressure on connector pin count and provides a differential signaling option that can improve noise immunity when the board stack-up and return path are controlled. Validate the receiver, connector insertion loss, differential impedance, skew budget, and timing margin before production release.
おすすめ
Embedded Parallel Data Systems
The DS90CR281MTD fits embedded systems in which a programmable or application-specific engine produces a wide parallel data stream that must be transferred to another subsystem. The four LVDS outputs offer a structured way to reduce wiring while retaining a transmitted clock for synchronization. Firmware and hardware integration must account for startup timing, supply sequencing, receiver latency, and the exact data mapping defined by the Channel Link implementation.
おすすめ
Data Acquisition Cards
A data-acquisition card can use DS90CR281MTD to export sampled or processed parallel data over a compact differential cable connection. The 28-bit input and four LVDS streams are useful when the acquisition module has a broad internal data bus and the remote processor requires a high-bandwidth link. System design should include local decoupling, controlled-impedance routing, receiver termination, channel skew analysis, and a receiver architecture that supports the DS90CR281 Channel Link format.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: DS90CR281MTD — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | DS90CR285MTD |
|---|---|---|
| Package | 56-TSSOP (0.240, 6.10 mm width) | 56-TSSOP |
| Brand | Texas Instruments | Texas Instruments |
| Product Type | 28-Bit Channel Link Transmitter | +3.3 V Rising Edge Data Strobe LVDS 28-Bit Channel Link Transmitter |
| Supply Voltage Range | 4.5 V to 5.5 V | 3.3 V |
| Data Input Width | 28 bits | 28 bits |
| Protocol | LVDS | LVDS |
主な差別化要因
- Documented 5 V supply-domain operation (vs DS90CR285MTD)
- Four LVDS data streams for a 28-bit payload (vs DS90CR285MTD)
- Phase-locked clock transmitted with the data (vs DS90CR285MTD)
設計ノート
Route the DS90CR281MTD LVDS outputs as controlled-impedance differential pairs with constant spacing, minimal vias, and no unnecessary stubs. Match the PCB differential impedance to the receiver and cable specification, and keep the pair paths away from high-current switching nodes. Confirm output timing, skew, receiver capacitance, and the maximum supported data rate using the manufacturer datasheet before fixing the interconnect.
Place the DS90CR281MTD close to the parallel-logic source and place the local supply-decoupling network at the device power pins. Use the shortest practical connection from the source outputs to the transmitter inputs and maintain a continuous return path beneath the interface. The 56-pin TSSOP package leaves limited routing flexibility around the device, so floorplanning the logic and differential nets together is preferable to late-stage via changes.
Do not treat the 28-bit Channel Link designation as proof that every related transmitter is electrically interchangeable. DS90CR285MTD is documented as a 3.3 V rising-edge data-strobe device, whereas DS90CR281MTD uses a 4.5 V to 5.5 V supply. Before substitution, compare power rails, input thresholds, output levels, edge polarity, clock behavior, data mapping, and every numbered pin in the manufacturer pin-description tables.
Separate the LVDS routing from noisy power converters, clock-generating circuits, relay drivers, and high-speed memory buses where the board stack-up permits. Maintain a nearby ground reference and use a low-impedance chassis or enclosure connection when the cable leaves the board. EMI performance depends on connector shielding, cable balance, common-mode behavior, and the return path, so validate the complete assembly rather than only the transmitter output.
コンプライアンス情報
The available manufacturer and distributor information identifies the part as a commercial-grade Texas Instruments 56-TSSOP interface IC. RoHS, REACH, lead-free, halogen-free, and conflict-minerals statuses are not stated in the available product information.