Texas Instruments

DS90CR281MTD - 28-Bit LVDS Channel Link Transmitter | TI

MPN: DS90CR281MTD ✓ Hoạt động
4.5 V to 5.5 V Vdss 56-TSSOP (0.240, 6.10 mm width) Package Yes; phase-locked transmit clock Speed
MOQ: 1 |

DS90CR281MTD Tóm tắt

Texas Instruments DS90CR281MTD is a 28-bit Channel Link transmitter that converts 28 CMOS/TTL data bits into four LVDS data streams, with a transmitted clock, in a 56-pin TSSOP package. The device operates from a 4.5 V to 5.5 V supply and is intended for high-speed parallel-to-differential data transmission over balanced cables.

What is a Channel Link transmitter? A Channel Link transmitter is a parallel-to-differential interface IC that serializes or multiplexes multiple low-voltage digital signals onto fewer differential pairs. LVDS, or Low Voltage Differential Signaling, is a high-speed electrical interface that uses the voltage difference between two conductors to improve noise immunity and reduce cable size. In the DS90CR281MTD, 28 CMOS/TTL bits and the clock are carried over four LVDS data streams plus a transmitted clock pair.

Key features include 28-bit parallel data input, four LVDS output streams, LVDS protocol support, and operation from a 4.5 V to 5.5 V supply. The multiplexing arrangement reduces the conductor count required for a wide parallel bus. This is particularly useful when a system must move data between circuit boards, across a cable, or between a parallel processing subsystem and a high-speed communications section while maintaining differential-signal integrity.

The DS90CR281MTD uses a phase-locked transmit clock that is transmitted with the data. This arrangement allows the receiving equipment to recover the associated data timing from the differential interface rather than relying on a separate single-ended clock conductor. The receiver must support the corresponding Channel Link data format and LVDS signaling levels, so cable length, connector geometry, termination, and receiver capability remain important system-level considerations.

Typical applications include industrial control and data acquisition systems, instrumentation, test and measurement equipment, high-speed backplanes, industrial networking, and embedded systems that transfer wide parallel data over a cable. The 56-pin TSSOP package is suitable for surface-mount assembly, although the device requires careful routing of the high-speed differential outputs and a stable supply-decoupling network.

For PCB implementation, place the device close to the source logic, route LVDS pairs as controlled-impedance differential nets, and keep the input and output return paths short. Verify the receiver’s input capacitance, cable length, connector loss, and termination strategy before release. The manufacturer datasheet and the TI DS90CR281 product page are the appropriate references for pin assignment, timing, electrical characteristics, and application details.

Bộ thay thế dễ dàng lắp đặt cho DS90CR281MTD — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

Các biến thể trong loạt này

Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với DS90CR281MTD (cùng hình factor và footprint) — khác nhau ở Package, Product Type.

Texas Instruments
Package: 56-pin TSSOP
Product Type: 28-bit Channel Link LVDS transmitter
So sánh với DS90CR281MTD →

DS90CR285MTD

✅ Drop-In
Texas Instruments
📦 56-TSSOP
28-bit Channel Link LVDS transmitter · 3.3 V · 66 MHz · 28 bits · LVCMOS/LVTTL · 4 differential streams · 1 differential stream · 5 LVDS links

Liên hệ để biết giá

Xem tài liệu →

DS90CR281MTD Thông số kỹ thuật

Product Type 28-Bit Channel Link Transmitter
Data Input Width 28 bits
LVDS Output Streams 4
Supply Voltage Range 4.5 V to 5.5 V
Protocol LVDS
Logic Input Type CMOS/TTL
Transmitter Type Transmitter
Hộp 56-TSSOP (0.240, 6.10 mm width)
Number of Terminals 56
Kiểu lắp đặt Surface Mount
Package Shape Rectangular
Terminal Form Gull Wing
Temperature Grade Commercial
Packaging Tube
Transmitted Clock Yes; phase-locked transmit clock
Differential Output Data Pairs 4 data pairs plus 1 clock pair

Hướng dẫn cấu hình chân DS90CR281MTD rectangular

Cấu hình chân cho DS90CR281MTD (rectangular gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.

Bảng cấu hình chân rectangular cho DS90CR281MTD

Không có dữ liệu chân cụ thể sẵn có cho DS90CR281MTD.

Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.

Ứng dụng tiêu biểu

DS90CR281MTD phù hợp cho 6 Áp dụngs: Industrial Data Acquisition, Test and Measurement Instrumentation, Industrial Networking, High-Speed Backplanes, Embedded Parallel Data Systems, Data Acquisition Cards.

🏭

Industrial Data Acquisition

The DS90CR281MTD is suitable for industrial data-acquisition systems that collect a wide parallel data set and transfer it to a remote processing or storage section. Its 28 CMOS/TTL input bits are converted into four LVDS data streams, reducing the number of conductors required across a cable or board-to-board link. The transmitted phase-locked clock supports timing recovery at the receiver. Use a receiver with compatible LVDS thresholds and verify cable length, data rate, grounding, and industrial environmental requirements.

🖥️

Test and Measurement Instrumentation

The DS90CR281MTD can connect a wide parallel measurement or control bus to a high-speed instrument chassis through balanced LVDS links. Four differential data streams carry the 28-bit payload more compactly than 28 single-ended conductors, while the transmitted clock provides the receiver with a timing reference. The design must account for connector loss, cable length, receiver bandwidth, termination, and the 4.5 V to 5.5 V supply requirement of the transmitter.

🌐

Industrial Networking

DS90CR281MTD is applicable to industrial network equipment that needs a compact differential connection between parallel processing logic and a communications or line-card module. LVDS helps maintain signal integrity over a balanced cable by rejecting common-mode noise and reducing the conductor count of the link. The implementation should be validated for the intended data rate, receiver capability, cable impedance, connector geometry, and the separation between switching circuitry and the differential pairs.

🖥️

High-Speed Backplanes

The DS90CR281MTD can be used in a backplane or mezzanine interface where a 28-bit parallel bus must cross a connector or cable assembly. Multiplexing the bus into four LVDS data streams reduces pressure on connector pin count and provides a differential signaling option that can improve noise immunity when the board stack-up and return path are controlled. Validate the receiver, connector insertion loss, differential impedance, skew budget, and timing margin before production release.

🧩

Embedded Parallel Data Systems

The DS90CR281MTD fits embedded systems in which a programmable or application-specific engine produces a wide parallel data stream that must be transferred to another subsystem. The four LVDS outputs offer a structured way to reduce wiring while retaining a transmitted clock for synchronization. Firmware and hardware integration must account for startup timing, supply sequencing, receiver latency, and the exact data mapping defined by the Channel Link implementation.

📺

Data Acquisition Cards

A data-acquisition card can use DS90CR281MTD to export sampled or processed parallel data over a compact differential cable connection. The 28-bit input and four LVDS streams are useful when the acquisition module has a broad internal data bus and the remote processor requires a high-bandwidth link. System design should include local decoupling, controlled-impedance routing, receiver termination, channel skew analysis, and a receiver architecture that supports the DS90CR281 Channel Link format.

What is the DS90CR281MTD used for?
The DS90CR281MTD is a Texas Instruments 28-bit Channel Link transmitter for converting parallel CMOS/TTL data into four LVDS data streams. It also transmits a phase-locked clock, allowing a compatible receiver to recover the associated data timing over a balanced cable or board-to-board connection. The manufacturer product information identifies the device as a 28-bit Channel Link transmitter using the LVDS protocol.
What is the operating voltage of DS90CR281MTD?
The DS90CR281MTD operates from a 4.5 V to 5.5 V supply. This supply range is stated in the DS90CR281MTD specifications and is appropriate for systems using a nominal 5 V power rail. The complete electrical limits, including input thresholds, output levels, and timing parameters, should be checked in the manufacturer datasheet before designing the interface.
How many LVDS data streams does DS90CR281MTD provide?
The DS90CR281MTD provides four LVDS data streams for its 28-bit parallel input. The transmitted clock is carried separately as a differential clock pair, making the interface use four data pairs and one clock pair in addition to the required return or reference conductors. This arrangement substantially reduces the conductor count compared with carrying 28 single-ended data signals and a clock independently.
Where can I download the DS90CR281MTD datasheet PDF?
The official Texas Instruments DS90CR281 product page provides the manufacturer datasheet and technical documentation for DS90CR281MTD. Search the product page for the DS90CR281 datasheet and order-information documents. The component is also listed as a 56-TSSOP interface device by distributors, which can help confirm the package and sourcing identity without replacing the manufacturer document as the engineering reference.
Where can I find the DS90CR281MTD pinout?
The DS90CR281MTD pinout is found in the pin-description and package-information sections of the Texas Instruments DS90CR281 datasheet. The device is identified as a 56-pin TSSOP, but the complete numbered signal assignment is not included in the distributor search text. Use the manufacturer pin-description table to map the parallel inputs, LVDS outputs, power pins, ground pins, and control connections before laying out a PCB.
Can DS90CR285MTD replace DS90CR281MTD?
DS90CR285MTD is a related Texas Instruments 28-bit Channel Link transmitter listed in the same package family, but it is identified as a 3.3 V rising-edge data-strobe LVDS transmitter. DS90CR281MTD operates from 4.5 V to 5.5 V, so the supply-voltage difference is approximately 2.2 V at the upper comparison point and must be considered. Verify the complete pinout, voltage levels, edge timing, and receiver compatibility before treating it as a drop-in replacement.
What is the difference between DS90CR281MTD and DS90CR285MTD?
The principal documented difference is the supply-voltage domain: DS90CR285MTD is identified as a 3.3 V rising-edge data-strobe LVDS transmitter, while DS90CR281MTD operates from 4.5 V to 5.5 V. Both are 28-bit Channel Link transmitters in the 56-pin TSSOP family. Exact data rate, strobe behavior, output timing, and pin compatibility should be compared in the manufacturer datasheets rather than inferred from the family name.
Is DS90CR281MTD suitable for industrial data-acquisition equipment?
Yes, DS90CR281MTD is suitable for industrial data-acquisition equipment when the system uses compatible CMOS/TTL inputs and an LVDS receiver. Its four LVDS data streams reduce the number of cable conductors needed for a wide parallel bus, while the transmitted clock supports timing recovery at the receiving end. Industrial temperature, isolation, grounding, surge protection, and enclosure requirements should be evaluated separately from the IC specification.
What is the best drop-in replacement for DS90CR281MTD?
The best replacement is the part whose complete pinout, supply voltage, logic levels, timing, LVDS output characteristics, and receiver compatibility match the existing board. DS90CR285MTD is a relevant same-family candidate, but the documented 3.3 V supply differs from the DS90CR281MTD 4.5 V to 5.5 V range. Therefore, verify the manufacturer pinout and electrical tables before committing to a replacement.
When should I choose DS90CR281MTD over a 3.3 V Channel Link transmitter?
Choose DS90CR281MTD when the surrounding logic operates from a 5 V supply and the board requires the documented 4.5 V to 5.5 V interface conditions. A 3.3 V Channel Link transmitter may be preferable in a system whose logic rails and receiver are fully 3.3 V compatible. The decision should be based on voltage levels, edge timing, data rate, pin mapping, and cable topology, not only on the 28-bit Channel Link label.
Does DS90CR281MTD require a separate clock connection?
The DS90CR281MTD includes a phase-locked transmit clock that is transmitted with the data, so the receiver can recover the associated clock from the differential clock pair. The interface still requires a compatible LVDS Channel Link receiver and correct board or cable termination. The datasheet should be used to confirm the electrical connection and timing requirements for the particular system implementation.
Where can I buy DS90CR281MTD and check the current lead time?
Use the Request a Quote form on this page to request DS90CR281MTD availability, current lead time, order quantity, and packaging requirements. The device is listed commercially as a 56-TSSOP Texas Instruments interface IC. Current stock and delivery timing can change, so a quote request is the appropriate way to confirm the exact MPN, tube quantity, and shipment schedule.
What is the price of DS90CR281MTD?
The current DS90CR281MTD commercial price depends on quantity, packaging, and market conditions. Use the Request a Quote form on this page to obtain a current quotation for the exact MPN and required quantity. The product is identified as a Texas Instruments 56-TSSOP Channel Link transmitter, and the 56-pin TSSOP tube packaging should be confirmed on the order.
Is DS90CR281MTD in stock?
Stock status for DS90CR281MTD should be confirmed through the Request a Quote form on this page, using the exact MPN and required tube quantity. The part is listed as a commercially graded 56-TSSOP interface device, but inventory availability can vary by quantity and supplier. A quote response can confirm current allocation, lead time, and shipment status for the intended order.
What are the key specifications of DS90CR281MTD that engineers should know?
The key documented specifications are a 28-bit CMOS/TTL input, four LVDS data streams, a 4.5 V to 5.5 V supply range, and a 56-pin TSSOP package. The device is a transmitter using the LVDS protocol and transmits a phase-locked clock. Data rate, timing limits, output levels, thermal limits, and detailed pin assignments should be taken from the manufacturer datasheet for the final design.
How do I design the PCB around DS90CR281MTD?
Place the DS90CR281MTD close to the parallel-logic source, provide local supply decoupling, and route the LVDS outputs as controlled-impedance differential pairs with matched spacing and minimal stubs. Confirm the receiver's termination requirements, connector or cable loss, and the maximum supported data rate. The search information identifies the package as 56-TSSOP, but the manufacturer pin-description table is required for exact PCB assignments.

Dữ liệu tham khảo kỹ thuật cho DS90CR281MTD — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose DS90CR281MTD when the system uses a 5 V logic domain and needs a 28-bit CMOS/TTL input converted to four LVDS data streams with a transmitted clock. The 56-pin TSSOP package is appropriate for a surface-mounted board design, but the exact data rate, pinout, output timing, and receiver requirements must be confirmed from the manufacturer documentation. DS90CR285MTD is a related 3.3 V rising-edge data-strobe transmitter in the same package family; consider it only when the power domain and edge behavior are compatible, or when a supply-domain change is acceptable. Because no other drop-in candidate was confirmed by the cross-reference results, do not substitute a generic LVDS transmitter solely because it has 28 data inputs. Validate voltage levels, clocking, receiver format, termination, cable length, and PCB layout as one complete interface.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này DS90CR285MTD
Package 56-TSSOP (0.240, 6.10 mm width) 56-TSSOP
Brand Texas Instruments Texas Instruments
Product Type 28-Bit Channel Link Transmitter +3.3 V Rising Edge Data Strobe LVDS 28-Bit Channel Link Transmitter
Supply Voltage Range 4.5 V to 5.5 V 3.3 V
Data Input Width 28 bits 28 bits
Protocol LVDS LVDS

Bảo phân biệt quan trọng

  • Documented 5 V supply-domain operation (vsDS90CR285MTD)
  • Four LVDS data streams for a 28-bit payload (vsDS90CR285MTD)
  • Phase-locked clock transmitted with the data (vsDS90CR285MTD)

Ghi chú thiết kế

Route the DS90CR281MTD LVDS outputs as controlled-impedance differential pairs with constant spacing, minimal vias, and no unnecessary stubs. Match the PCB differential impedance to the receiver and cable specification, and keep the pair paths away from high-current switching nodes. Confirm output timing, skew, receiver capacitance, and the maximum supported data rate using the manufacturer datasheet before fixing the interconnect.

Place the DS90CR281MTD close to the parallel-logic source and place the local supply-decoupling network at the device power pins. Use the shortest practical connection from the source outputs to the transmitter inputs and maintain a continuous return path beneath the interface. The 56-pin TSSOP package leaves limited routing flexibility around the device, so floorplanning the logic and differential nets together is preferable to late-stage via changes.

Do not treat the 28-bit Channel Link designation as proof that every related transmitter is electrically interchangeable. DS90CR285MTD is documented as a 3.3 V rising-edge data-strobe device, whereas DS90CR281MTD uses a 4.5 V to 5.5 V supply. Before substitution, compare power rails, input thresholds, output levels, edge polarity, clock behavior, data mapping, and every numbered pin in the manufacturer pin-description tables.

Separate the LVDS routing from noisy power converters, clock-generating circuits, relay drivers, and high-speed memory buses where the board stack-up permits. Maintain a nearby ground reference and use a low-impedance chassis or enclosure connection when the cable leaves the board. EMI performance depends on connector shielding, cable balance, common-mode behavior, and the return path, so validate the complete assembly rather than only the transmitter output.

Thông tin tuân thủ

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

The available manufacturer and distributor information identifies the part as a commercial-grade Texas Instruments 56-TSSOP interface IC. RoHS, REACH, lead-free, halogen-free, and conflict-minerals statuses are not stated in the available product information.

Dữ liệu được xác minh vào: 2026-11-10 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

DS90CR281MTD datasheet DS90CR281MTD pinout DS90CR281MTD datasheet pdf DS90CR281MTD specifications DS90CR281MTD equivalent DS90CR281MTD replacement DS90CR281MTD cross reference DS90CR281MTD vs DS90CR285MTD DS90CR281MTD price DS90CR281MTD stock Texas Instruments DS90CR281MTD 56-TSSOP LVDS transmitter DS90CR281MTD industrial interface DS90CR281MTD Channel Link DS90CR281MTD 4.5 V 5.5 V

Các bộ phận và thuật ngữ liên quan

Texas Instruments DS90CR281MTD DS90CR285MTD 28-Bit Channel Link Channel Link transmitter LVDS Low Voltage Differential Signaling CMOS/TTL parallel-to-differential interface data transmitter interface IC semiconductor phase-locked transmit clock differential data pair 56-TSSOP TSSOP package surface-mount package industrial data acquisition test and measurement industrial networking high-speed backplane data acquisition card power management
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ