DS90LV804TSQ - 4-Channel 800 Mbps LVDS Buffer | Texas Instruments
部品番号: DS90LV804TSQ ✗ 生産終了DS90LV804TSQ 概要
An LVDS buffer, also called an LVDS repeater, is a high-speed interface device that regenerates differential signals so they can travel reliably across cables, backplanes, or board-to-board links. Its role in the signal-chain hierarchy is LVDS interface IC > signal buffer/repeater > differential line driver and receiver interface > high-speed digital communication component. Such buffers are especially useful when routing loss, impedance discontinuities, connector transitions, or long cable runs degrade signal integrity.
The DS90LV804 supports four LVDS channels at up to 800 Mbps per channel. Internal source termination on both inputs and outputs simplifies board layouts by bringing termination close to the relevant interface pins. This is particularly valuable in distributed systems where signal integrity depends on data rate, cable type, cable length, and termination strategy. The output-enable function adds another level of system control by allowing unused outputs and bias circuitry to enter a tri-state, low-power state.
The electrical design balances high data throughput with practical interconnect flexibility. LVDS signaling uses differential voltage and low-voltage swings to improve noise immunity and reduce electromagnetic emissions compared with single-ended high-speed signaling. Repeating the signal restores signal levels before it reaches another segment of the system, helping limit degradation across multiple distribution points. The DS90LV804 is therefore positioned as a four-lane LVDS signal-conditioning element rather than a general-purpose logic buffer.
Typical uses include point-to-point and distributed LVDS links inside industrial control systems, test equipment, communications equipment, and data-processing subsystems. The device can also support clock distribution, backplane routing, and cable-extension arrangements where four independent channels are useful. Its compact WQFN package helps reduce board area, but its exposed-pad construction and high-speed interfaces require careful thermal, grounding, and return-path planning.
For a new layout, use the manufacturer pin-description table and the 32-pin WQFN land pattern exactly. Place bypass and termination components close to their associated pins, preserve a continuous ground reference beneath the package, and avoid routing LVDS traces over splits in the reference plane. Validate differential impedance, pair length matching, connector transitions, and receiver thresholds with the intended cable and connector configuration.
This page consolidates the verified channel count, data rate, package, termination, power-state, and sourcing details into an engineering-focused guide. It also documents drop-in replacement constraints, pin-layout uncertainty, practical high-speed design guidance, and application-specific selection considerations for the DS90LV804TSQ.
ドロップイン代替品: DS90LV804TSQ — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
DS90LV804TSQ/NOPB
✅ ドロップイン📋 参考代替品(カタログ未掲載)
DS90LV804TSQX
✅ ドロップイン📋 参考代替品(カタログ未掲載)
DS90LV804TSQX/NOPB
✅ ドロップイン📋 参考代替品(カタログ未掲載)
DS90LV804TSQ 仕様
| Product Type | 4-channel LVDS buffer/repeater |
| Number of Channels | 4 channels |
| Maximum Data Rate | 800 Mbps per channel |
| Input Termination | Internal source termination |
| Output Termination | Internal source termination |
| Output Enable | Yes |
| Disabled Output State | Tri-state, low-power mode |
| パッケージ | 32-pin WQFN (5 x 5 mm) |
| ピン数 | 32 pins |
| Lead Style | No lead |
| Package Shape | Square |
| Temperature Grade | Industrial |
| 出力電圧 | 0.6 V |
| Moisture Sensitivity Level | MSL 1 |
| RoHS ステータス | Non-compliant |
| REACH Status | Unaffected |
DS90LV804TSQ square ピン配置ガイド
DS90LV804TSQ (square パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: DS90LV804TSQ.
詳細は データシート をご参照ください。
主な用途
DS90LV804TSQ の用途: 6 件s: Industrial Backplane LVDS Routing, Point-to-Point LVDS Cable Extension, Clock and Parallel-Signal Distribution, Test and Measurement Instrumentation, Data Processing Subsystems, Low-Power Managed Signal Distribution.
Industrial Backplane LVDS Routing
The DS90LV804TSQ fits four-channel industrial backplane routing because it regenerates differential signals at up to 800 Mbps per channel and provides internal input and output source termination. The device can preserve signal integrity across connector and board transitions where reflection or loss becomes significant. Placing the terminations close to interface pins simplifies the board while supporting controlled tri-state operation through the output-enable function. Validate differential impedance, pair-length balance, connector loss, and receiver thresholds in the complete backplane.
おすすめ
Point-to-Point LVDS Cable Extension
The DS90LV804TSQ is useful between a transmitter and distant receiver when four LVDS links must cross a cable assembly or routed board-to-board segment. Its four channels allow parallel data or independent control signals to be repeated consistently, while the 800 Mbps per-channel rate supports high-throughput industrial and communications links. Internal source termination reduces the number of external termination components. The complete channel must still be simulated and measured because cable length, skew, loss, and connector transitions determine achievable margin.
おすすめ
Clock and Parallel-Signal Distribution
The DS90LV804TSQ can distribute a differential clock alongside three related low-voltage differential signals across a compact system. Four independently repeated channels are valuable when a source must reach several destinations through balanced wiring, and the output-enable control permits unused links to enter tri-state, low-power operation. The 32-pin WQFN package supports compact implementation, although exposed-pad layout and high-speed return paths remain essential. Confirm that every destination supports the repeater's LVDS levels and timing.
おすすめ
Test and Measurement Instrumentation
The DS90LV804TSQ is appropriate for high-speed internal routing in test and measurement equipment where several differential channels must pass through connectors, cables, or switching structures. Four channels at up to 800 Mbps provide a compact way to regenerate signals, while integrated input and output termination helps maintain controlled impedance near the device. The industrial temperature grade and output-enable control support robust instrument architectures. Use short return paths and verify timing margins against the acquisition or source circuitry.
おすすめ
Data Processing Subsystems
The DS90LV804TSQ can serve as a four-lane interface conditioner between data-processing modules that exchange LVDS signals across a short cable or dense backplane. At 800 Mbps per channel, it regenerates the differential waveform before accumulated loss harms timing or amplitude. Its small 32-pin WQFN package preserves board area, and internal source termination reduces external component count. Care is required around processor supply sequencing, exposed-pad grounding, and any requirement for independently disabled outputs.
おすすめ
Low-Power Managed Signal Distribution
The DS90LV804TSQ fits systems that need high-speed links but must disable unused outputs to reduce activity. Its output-enable control places the LVDS outputs and internal bias generators into a tri-state, low-power mode, allowing power management to be coordinated with the rest of the equipment. Four channels provide useful consolidation for compact control, data, or clock routing. Firmware and hardware design must ensure that disabled outputs present the intended state to receivers and that power-up sequencing satisfies every downstream device.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: DS90LV804TSQ — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | DS90LV804TSQ/NOPB | DS90LV804TSQX | DS90LV804TSQX/NOPB |
|---|---|---|---|---|
| Package | 32-pin WQFN (5 x 5 mm) | 32-pin WQFN (5 x 5 mm) | 32-pin WQFN (5 x 5 mm) | 32-pin WQFN (5 x 5 mm) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Channel Count | 4 channels | 4 channels | 4 channels | 4 channels |
| Maximum Data Rate | 800 Mbps per channel | 800 Mbps per channel | 800 Mbps per channel | 800 Mbps per channel |
| Product Type | LVDS buffer/repeater | LVDS buffer/repeater | LVDS buffer/repeater | LVDS buffer/repeater |
| Input Termination | Internal source termination | Internal source termination | Internal source termination | Internal source termination |
| Output Termination | Internal source termination | Internal source termination | Internal source termination | Internal source termination |
| Output Enable | Yes | Yes | Yes | Yes |
| Disabled Output State | Tri-state, low-power mode | Tri-state, low-power mode | Tri-state, low-power mode | Tri-state, low-power mode |
主な差別化要因
- Four independently repeated LVDS channels (vs DS90LV804TSQX)
- Integrated termination at both sides of the buffer (vs DS90LV804TSQ/NOPB)
- Output-enable-controlled low-power state (vs DS90LV804TSQX/NOPB)
設計ノート
Use the Texas Instruments 32-pin WQFN land pattern and exposed-pad connection exactly as specified in the manufacturer package drawing. Preserve a continuous ground reference beneath the device, keep LVDS pairs over that reference, and minimize stubs and test-pad branches. The internal source termination helps place termination near interface pins, but poor return-path continuity can still create reflections that undermine the benefit of the integrated terminations.
Validate the complete channel rather than only the DS90LV804TSQ output waveform. Model the source, receiver, cable or PCB loss, connector transitions, pair skew, and receiver termination with the actual 800 Mbps signaling conditions. Compare differential voltage, rise and fall time, eye opening, and jitter at the receiver. A channel that works with short point-to-point wiring may require different spacing, routing, or cable when repeated across a larger system.
Do not assume that every device sharing the 32-pin WQFN outline is a drop-in replacement. The DS15BR400 has been discussed as a possible replacement, but the documented pinout is slightly different and compatibility was not confirmed. Compare power, ground, enables, termination, channel inputs, channel outputs, and exposed-pad assignments pin by pin before substituting any part. Also verify the exact production orderable code rather than relying only on the base DS90LV804 family name.
The WQFN exposed pad is part of the thermal path as well as the electrical ground path. Follow the manufacturer's land-pattern and solder-process recommendations, use the recommended pad geometry, and avoid placing a keepout or isolated copper region under the device. Thermal performance depends on the board copper area and both-side thermal vias specified by the package documentation. Check enclosure temperature and adjacent heat sources when the interface repeater operates in a compact system.
コンプライアンス情報
The cross-reference product information identifies the part as RoHS non-compliant, REACH unaffected, and MSL 1. AEC-Q100, lead-free, halogen-free, and conflict-minerals status are not established.