Texas Instruments

DS90LV804TSQ - 4-Channel 800 Mbps LVDS Buffer | Texas Instruments

부품 번호: DS90LV804TSQ ✗ 단종
0.6 V Vdss 32-pin WQFN (5 x 5 mm) Package
MOQ: 1 |

DS90LV804TSQ 개요

Texas Instruments DS90LV804TSQ is a four-channel 800 Mbps LVDS buffer/repeater in a 32-pin WQFN package measuring 5 x 5 mm. The device adds internal input and output source termination, allowing designers to place termination close to receiver inputs and driver outputs while reducing external passive-component requirements. An output-enable control supports tri-state operation and low-power control of the LVDS outputs and internal bias generators.

An LVDS buffer, also called an LVDS repeater, is a high-speed interface device that regenerates differential signals so they can travel reliably across cables, backplanes, or board-to-board links. Its role in the signal-chain hierarchy is LVDS interface IC > signal buffer/repeater > differential line driver and receiver interface > high-speed digital communication component. Such buffers are especially useful when routing loss, impedance discontinuities, connector transitions, or long cable runs degrade signal integrity.

The DS90LV804 supports four LVDS channels at up to 800 Mbps per channel. Internal source termination on both inputs and outputs simplifies board layouts by bringing termination close to the relevant interface pins. This is particularly valuable in distributed systems where signal integrity depends on data rate, cable type, cable length, and termination strategy. The output-enable function adds another level of system control by allowing unused outputs and bias circuitry to enter a tri-state, low-power state.

The electrical design balances high data throughput with practical interconnect flexibility. LVDS signaling uses differential voltage and low-voltage swings to improve noise immunity and reduce electromagnetic emissions compared with single-ended high-speed signaling. Repeating the signal restores signal levels before it reaches another segment of the system, helping limit degradation across multiple distribution points. The DS90LV804 is therefore positioned as a four-lane LVDS signal-conditioning element rather than a general-purpose logic buffer.

Typical uses include point-to-point and distributed LVDS links inside industrial control systems, test equipment, communications equipment, and data-processing subsystems. The device can also support clock distribution, backplane routing, and cable-extension arrangements where four independent channels are useful. Its compact WQFN package helps reduce board area, but its exposed-pad construction and high-speed interfaces require careful thermal, grounding, and return-path planning.

For a new layout, use the manufacturer pin-description table and the 32-pin WQFN land pattern exactly. Place bypass and termination components close to their associated pins, preserve a continuous ground reference beneath the package, and avoid routing LVDS traces over splits in the reference plane. Validate differential impedance, pair length matching, connector transitions, and receiver thresholds with the intended cable and connector configuration.

This page consolidates the verified channel count, data rate, package, termination, power-state, and sourcing details into an engineering-focused guide. It also documents drop-in replacement constraints, pin-layout uncertainty, practical high-speed design guidance, and application-specific selection considerations for the DS90LV804TSQ.

드롭인 대체품: DS90LV804TSQ — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

DS90LV804TSQ/NOPB

✅ 드롭인
📦 32-pin WQFN (5 x 5 mm)
Same four-channel 800 Mbps architecture and 32-pin WQFN package; ordering code changes from TSQ to TSQ/NOPB, with terminal-finish terminology requiring final ordering-code review.

📋 참조 대체품 (카탈로그에 없음)

DS90LV804TSQX

✅ 드롭인
📦 32-pin WQFN (5 x 5 mm)
Same DS90LV804 family, four-channel 800 Mbps function, and 32-pin WQFN package; TSQX ordering suffix differs and its exact temperature and marking details require datasheet confirmation.

📋 참조 대체품 (카탈로그에 없음)

DS90LV804TSQX/NOPB

✅ 드롭인
📦 32-pin WQFN (5 x 5 mm)
Same DS90LV804 family and 32-pin WQFN footprint, with TSQX/NOPB ordering-code differences; confirm temperature grade, terminal finish, and exact marking before substitution.

📋 참조 대체품 (카탈로그에 없음)

DS90LV804TSQ 사양

Product Type 4-channel LVDS buffer/repeater
Number of Channels 4 channels
Maximum Data Rate 800 Mbps per channel
Input Termination Internal source termination
Output Termination Internal source termination
Output Enable Yes
Disabled Output State Tri-state, low-power mode
패키지 32-pin WQFN (5 x 5 mm)
핀 수 32 pins
Lead Style No lead
Package Shape Square
Temperature Grade Industrial
출력 전압 0.6 V
Moisture Sensitivity Level MSL 1
RoHS 상태 Non-compliant
REACH Status Unaffected

DS90LV804TSQ square 핀 구성 가이드

DS90LV804TSQ(square 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.

DS90LV804TSQ의 square 패키지 핀아웃 다이어그램

다음에 대한 상세 핀아웃 데이터 없음: DS90LV804TSQ.

다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.

일반적인 애플리케이션

DS90LV804TSQ 적합 용도: 6 애플리케이션s: Industrial Backplane LVDS Routing, Point-to-Point LVDS Cable Extension, Clock and Parallel-Signal Distribution, Test and Measurement Instrumentation, Data Processing Subsystems, Low-Power Managed Signal Distribution.

🏭

Industrial Backplane LVDS Routing

The DS90LV804TSQ fits four-channel industrial backplane routing because it regenerates differential signals at up to 800 Mbps per channel and provides internal input and output source termination. The device can preserve signal integrity across connector and board transitions where reflection or loss becomes significant. Placing the terminations close to interface pins simplifies the board while supporting controlled tri-state operation through the output-enable function. Validate differential impedance, pair-length balance, connector loss, and receiver thresholds in the complete backplane.

🌐

Point-to-Point LVDS Cable Extension

The DS90LV804TSQ is useful between a transmitter and distant receiver when four LVDS links must cross a cable assembly or routed board-to-board segment. Its four channels allow parallel data or independent control signals to be repeated consistently, while the 800 Mbps per-channel rate supports high-throughput industrial and communications links. Internal source termination reduces the number of external termination components. The complete channel must still be simulated and measured because cable length, skew, loss, and connector transitions determine achievable margin.

🖥️

Clock and Parallel-Signal Distribution

The DS90LV804TSQ can distribute a differential clock alongside three related low-voltage differential signals across a compact system. Four independently repeated channels are valuable when a source must reach several destinations through balanced wiring, and the output-enable control permits unused links to enter tri-state, low-power operation. The 32-pin WQFN package supports compact implementation, although exposed-pad layout and high-speed return paths remain essential. Confirm that every destination supports the repeater's LVDS levels and timing.

🔧

Test and Measurement Instrumentation

The DS90LV804TSQ is appropriate for high-speed internal routing in test and measurement equipment where several differential channels must pass through connectors, cables, or switching structures. Four channels at up to 800 Mbps provide a compact way to regenerate signals, while integrated input and output termination helps maintain controlled impedance near the device. The industrial temperature grade and output-enable control support robust instrument architectures. Use short return paths and verify timing margins against the acquisition or source circuitry.

🖥️

Data Processing Subsystems

The DS90LV804TSQ can serve as a four-lane interface conditioner between data-processing modules that exchange LVDS signals across a short cable or dense backplane. At 800 Mbps per channel, it regenerates the differential waveform before accumulated loss harms timing or amplitude. Its small 32-pin WQFN package preserves board area, and internal source termination reduces external component count. Care is required around processor supply sequencing, exposed-pad grounding, and any requirement for independently disabled outputs.

⚡

Low-Power Managed Signal Distribution

The DS90LV804TSQ fits systems that need high-speed links but must disable unused outputs to reduce activity. Its output-enable control places the LVDS outputs and internal bias generators into a tri-state, low-power mode, allowing power management to be coordinated with the rest of the equipment. Four channels provide useful consolidation for compact control, data, or clock routing. Firmware and hardware design must ensure that disabled outputs present the intended state to receivers and that power-up sequencing satisfies every downstream device.

What is the DS90LV804TSQ?
The DS90LV804TSQ is a four-channel, 800 Mbps LVDS buffer/repeater from Texas Instruments in a 32-pin WQFN package. According to the manufacturer product page, it provides internal input and output source termination, placing termination close to receiver inputs and driver outputs. An output-enable pin also controls the LVDS outputs and internal bias generators for tri-state, low-power operation.
What are the key specifications of DS90LV804TSQ that engineers should know?
The DS90LV804TSQ provides four LVDS channels, an 800 Mbps maximum data rate, internal input and output source termination, and an output-enable control. Texas Instruments identifies the package as 32-pin WQFN in a 5 x 5 mm outline. The device is an industrial-temperature-grade signal buffer/repeater, and the listed product information identifies a 0.6 V output value. Additional electrical limits should be confirmed in the manufacturer datasheet.
Where can I download the DS90LV804TSQ datasheet PDF?
The official DS90LV804 datasheet and supporting technical documentation are available from the Texas Instruments product page at https://www.ti.com/product/DS90LV804. The page provides the current manufacturer documentation for the DS90LV804 family and identifies the data sheet as revision L. Use the pin-description table, electrical-characteristics tables, and package drawings from that documentation when creating a PCB footprint or checking operating limits.
Where can I find the DS90LV804TSQ pinout?
The DS90LV804TSQ pinout is defined in the pin-configuration section of the Texas Instruments DS90LV804 data sheet linked from the official product page. The component is a 32-pin WQFN with an exposed thermal pad in a 5 x 5 mm outline. Use the manufacturer pin table rather than an inferred layout because the input termination, output enable, power pins, channel pins, and exposed-pad connections must be assigned exactly before routing.
Is DS90LV804TSQ the same as DS90LV804TSQ/NOPB?
The DS90LV804TSQ and DS90LV804TSQ/NOPB identify closely related orderable versions of the same four-channel, 800 Mbps LVDS buffer/repeater in a 32-pin WQFN package. The NOPB designation denotes a no-lead-free-terminology order variant, while TSQ carries the surface-mount package designation. Engineers should verify the exact orderable part number, marking, terminal finish, and current datasheet revision before treating the two as interchangeable production parts.
What is the best drop-in replacement for DS90LV804TSQ?
The DS90LV804TSQ/NOPB is the closest documented same-family replacement because it uses the same 32-pin 5 x 5 mm WQFN package and retains the four-channel, 800 Mbps LVDS architecture. No cross-brand drop-in replacement is established by the available manufacturer and cross-reference information. Treat the NOPB device as a candidate, then verify exact pin functions, electrical limits, temperature grade, and lifecycle status before production substitution.
Can DS15BR400 replace DS90LV804TSQ?
The DS15BR400 should not be treated as a confirmed pin-to-pin DS90LV804TSQ replacement. A Texas Instruments support discussion describes it as a possible drop-in replacement because the package is the same, but the discussion also states that the pinout is slightly different and leaves compatibility unconfirmed. Use it only after comparing every signal, power, enable, ground, and exposed-pad connection against both datasheets.
Where can I buy DS90LV804TSQ online?
Use the Request a Quote form on this XAIPART page to request DS90LV804TSQ availability, current commercial terms, and a formal quotation. The Request a Quote workflow provides a single route for price, stock confirmation, minimum-order quantity, and lead-time questions. The verified listings also identify the exact part in 32-pin 5 x 5 mm WQFN packaging, which helps confirm that the quotation concerns the correct orderable device.
What is the price of DS90LV804TSQ?
The current DS90LV804TSQ commercial price is not stated as a fixed amount on this page, and no qualifying quantity-break price table for the exact MPN is available in the verified listings. Submit the Request a Quote form with your required quantity, packaging preference, and destination. The quotation response should reflect current product availability, quantity breaks, and supply conditions rather than a stale historical price.
What is the lead time for DS90LV804TSQ?
The current lead time for DS90LV804TSQ must be confirmed through the Request a Quote form on this page. The verified listings establish the exact MPN and package, but they do not provide a manufacturer-authorized lead-time commitment for the requested quantity. Include your forecast quantity, target date, reel or tray requirements, and shipment destination when requesting the quotation.
Is DS90LV804TSQ in stock?
Stock status for a specific DS90LV804TSQ quantity should be confirmed through the Request a Quote form on this page because inventory changes by package, quantity, and fulfillment date. The manufacturer lists the DS90LV804 family as orderable, but that does not establish a fixed stock quantity. Request a written availability and lead-time confirmation for the exact orderable MPN before committing a production schedule.
When should I choose DS90LV804TSQ over another LVDS repeater?
Choose the DS90LV804TSQ when the design needs four independent LVDS channels, operation up to 800 Mbps per channel, integrated source termination at both input and output, and a compact 32-pin WQFN footprint. Its output-enable control supports controlled tri-state and low-power states, making it useful in multi-drop or power-managed systems. Select another device only when its channel count, package, voltage, reach, signaling mode, or pinout better matches the link.
Is DS90LV804TSQ suitable for industrial backplane and cable links?
The DS90LV804TSQ is suitable as a candidate for industrial high-speed LVDS routing because it provides four 800 Mbps channels, internal source termination, and an industrial temperature grade. Its usefulness depends on cable type, length, data rate, connector behavior, and the receiver's termination scheme. Validate insertion loss, reflections, differential impedance, and jitter in the complete channel before releasing a production design.
What are the main DS90LV804TSQ design considerations?
The primary DS90LV804TSQ design considerations are package thermal performance, differential-impedance continuity, return-path integrity, and correct termination placement. Texas Instruments highlights internal input and output source termination as a way to remove extra termination components and place terminations close to interface pins. Keep bypass capacitors and any optional discrete components close to their pins, maintain an uninterrupted ground plane, and route each differential pair over a continuous reference plane.
What is the DS90LV804TSQ used for?
The DS90LV804TSQ is used to regenerate four high-speed differential LVDS signals across board-to-board, backplane, cable, or internal routing segments. Operating at up to 800 Mbps per channel, it helps restore signal levels between distribution points while integrated source termination limits the need for separate resistors. Common uses include distributed industrial links, clock distribution, test equipment, and communications subsystems with controlled low-power output states.

엔지니어링 참조 데이터: DS90LV804TSQ — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose the DS90LV804TSQ for a four-lane LVDS interface that operates at up to 800 Mbps per channel and benefits from integrated input and output source termination. The output-enable pin is valuable when unused channels must enter a controlled tri-state, low-power condition. Select DS90LV804TSQ/NOPB when its ordering and terminal-finish terms match the procurement specification; confirm the full part number and marking. Choose DS90LV804TSQX or DS90LV804TSQX/NOPB when their exact temperature or ordering characteristics fit the design, after checking the manufacturer documentation. Do not substitute the DS15BR400 solely because it uses a similar package: its documented pinout differs and full compatibility has not been established. For designs requiring a different channel count, voltage, reach, or signaling standard, select a different interface device rather than forcing a package-level match.

대체품과의 비교

파라미터 이 제품 DS90LV804TSQ/NOPB DS90LV804TSQX DS90LV804TSQX/NOPB
Package 32-pin WQFN (5 x 5 mm) 32-pin WQFN (5 x 5 mm) 32-pin WQFN (5 x 5 mm) 32-pin WQFN (5 x 5 mm)
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Channel Count 4 channels 4 channels 4 channels 4 channels
Maximum Data Rate 800 Mbps per channel 800 Mbps per channel 800 Mbps per channel 800 Mbps per channel
Product Type LVDS buffer/repeater LVDS buffer/repeater LVDS buffer/repeater LVDS buffer/repeater
Input Termination Internal source termination Internal source termination Internal source termination Internal source termination
Output Termination Internal source termination Internal source termination Internal source termination Internal source termination
Output Enable Yes Yes Yes Yes
Disabled Output State Tri-state, low-power mode Tri-state, low-power mode Tri-state, low-power mode Tri-state, low-power mode

주요 차별점

  • Four independently repeated LVDS channels (vs DS90LV804TSQX)
  • Integrated termination at both sides of the buffer (vs DS90LV804TSQ/NOPB)
  • Output-enable-controlled low-power state (vs DS90LV804TSQX/NOPB)

설계 노트

Use the Texas Instruments 32-pin WQFN land pattern and exposed-pad connection exactly as specified in the manufacturer package drawing. Preserve a continuous ground reference beneath the device, keep LVDS pairs over that reference, and minimize stubs and test-pad branches. The internal source termination helps place termination near interface pins, but poor return-path continuity can still create reflections that undermine the benefit of the integrated terminations.

Validate the complete channel rather than only the DS90LV804TSQ output waveform. Model the source, receiver, cable or PCB loss, connector transitions, pair skew, and receiver termination with the actual 800 Mbps signaling conditions. Compare differential voltage, rise and fall time, eye opening, and jitter at the receiver. A channel that works with short point-to-point wiring may require different spacing, routing, or cable when repeated across a larger system.

Do not assume that every device sharing the 32-pin WQFN outline is a drop-in replacement. The DS15BR400 has been discussed as a possible replacement, but the documented pinout is slightly different and compatibility was not confirmed. Compare power, ground, enables, termination, channel inputs, channel outputs, and exposed-pad assignments pin by pin before substituting any part. Also verify the exact production orderable code rather than relying only on the base DS90LV804 family name.

The WQFN exposed pad is part of the thermal path as well as the electrical ground path. Follow the manufacturer's land-pattern and solder-process recommendations, use the recommended pad geometry, and avoid placing a keepout or isolated copper region under the device. Thermal performance depends on the board copper area and both-side thermal vias specified by the package documentation. Check enclosure temperature and adjacent heat sources when the interface repeater operates in a compact system.

규정 준수 정보

RoHS
Non Compliant
REACH
Compliant
AEC-Q100
Unknown
무연
Unknown
무할로겐
Unknown
분쟁 광물
Unknown

The cross-reference product information identifies the part as RoHS non-compliant, REACH unaffected, and MSL 1. AEC-Q100, lead-free, halogen-free, and conflict-minerals status are not established.

관련 검색

ds90lv804tsq nopb DS90LV804TSQ datasheet DS90LV804TSQ datasheet pdf DS90LV804TSQ pinout DS90LV804TSQ equivalent DS90LV804TSQ replacement DS90LV804TSQ drop-in replacement DS90LV804TSQ vs DS90LV804TSQ/NOPB DS90LV804TSQ price DS90LV804TSQ stock Texas Instruments DS90LV804TSQ DS90LV804TSQ application circuit DS90LV804TSQ 32 WQFN pinout DS90LV804TSQ LVDS repeater

관련 부품 & 용어

Texas Instruments DS90LV804TSQ DS90LV804TSQ/NOPB DS90LV804TSQX DS90LV804TSQX/NOPB DS15BR400 LVDS Low-Voltage Differential Signaling LVDS buffer LVDS repeater signal buffer/repeater interface IC differential line interface high-speed digital communication 800 Mbps internal source termination tri-state output output enable low-power mode 32-pin WQFN WQFN package QFN package family surface-mount device SMD industrial temperature grade MSL 1 RoHS REACH
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기